Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IB13-R-001G
This bulletin outlines the procedures for using the Alpine Exchange Program (the "Exchange Program"). The Exchange Program must be used when any Alpine radio or other component covered by this bulletin is repaired under warranty and may also be used for radio and component repairs not covered under warranty. Contact Alpine directly for pricing and payment methods applicable to radio and component repairs not covered under warranty.
WB13-X-001B
Isuzu Commercial Truck of America, Inc. (ICTA) is providing the following procedural recommendations to improve dealer efficiency when submitting Parts Warranty claims. We strongly recommend dealers follow these procedures in order to avoid delays in Parts Warranty claim payments and/or claim chargeback. This bulletin was revised to add a Parts Warranty Form
WB13-X-001A
Isuzu Commercial Truck of America, Inc. (ICTA) is providing the following procedural recommendations to improve dealer efficiency when submitting Parts Warranty claims. We strongly recommend dealers follow these procedures in order to avoid delays in Parts Warranty claim payments and/or claim chargeback.
IB09-X-002B
The following is a list of the Isuzu-recommended Threebond product part numbers identified in the various Isuzu Workshop Manuals and bulletins. If a Threebond product is unavailable, we recommend that you utilize the chart below to find equivalent of similar products (when available) from Loctite and Permatex.
IB09-X-004C
The Isuzu Commercial Truck of America (ICTA) Service Technical Assistance Center (TAC) provides diagnostic support to Isuzu dealer technicians repairing Isuzu vehicles in and out of vehicle warranty. A TAC case number will be issued solely for information tracking purposes and future contact reference.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIC6107A
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-06-01-012G
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
PIC5491J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5029G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
PIC5953A
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5226A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5338
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT5264C
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIT3271G
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC3278F
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT5264A
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIP5232
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5226
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT3099M
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIC5959B
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP5163A
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5088E
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
PIC5588B
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
05-06-04-035D
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
PIC5953
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5163
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
SB-13-04-S004
ISUZU: FUEL LEVER SENSOR SPECIAL POLICY ADJUSTMENT. CONTACTS MAY WEAR PREMATURELY. THIS MAY CAUSE THE GAUGE TO READ EMPTY EVEN AFTER FILLING THE FUEL TANK. MALFUNCTION INDICATOR LIGHT (MIL) MAY ALSO BECOME ILLUMINATED. *KB
PIC3718E
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
PIT3173C
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
PIC4310H
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT4907A
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIC4935D
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
379
INTERMITTENT NO CRANK, NO START, OR DELAYED CRANK. *NJ
0704003
ERRATIC SPEEDOMETER OPERATION OR SPEEDOMETER NEEDLE SHAKES ABOVE 60 MPH. *NJ
0704004
ABS LIGHT ON, DTC C0040 STORED. *NJ
191
ABS, RED BRAKE, SVC AND 4WD LIGHT ON, HVAC BLOWER INOPERATIVE. *NJ
96
DTC C0327 WITH OR WITHOUT ADDITIONAL DTC'S SETTING. WITH 4WD. *NJ
0511001
CENTER HIGH-MOUNT STOP LAMP (CHMSL) APPLIQUE LOOSE. *NJ
0605001
SERVICE 4WD LIGHT ILLUMINATED, DTC C0374 SET. *NJ
0701002
INFORMATION ON NEW IN-VEHICLE SERVICE PROCEDURE FOR REMOVAL/INSTALLATION OF LL8 CYLINDER HEAD. *NJ
0711015
REAR LIFTGATE GLASS MAY NOT LOCK WHEN USING REMOTE KEYLESS ENTRY (RKE) KEY FOB TRANSMITTER/DOOR LOCK SWITCH, LIFTGATE HATCH OR LIFTGATE GLASS MAY LOCK/UNLOCK WHEN REAR LIFTGATE GLASS BUTTON DEPRESSED. *NJ
0709002
ABS LIGHT ON, DTC'S C0265, C0201, U1041 SET AND / OR LOSS OF COMMUNICATION WITH BRAKE MODULE. *KB
0702001
VARIOUS DRIVEABILITY SYMPTOMS DUE TO CLOGGED FUEL INJECTORS, MIL DTC'S P0171, P0172, P0174, P0300, P1174, AND P1175. *KB UPDATED 08-03-07. *KB
0705004
INFORMATION ON 2-3 UP-SHIFT OR 3-2 DOWNSHIFT CLUNK NOISE IS HEARD. *KB
0704002
PRNDL DISPLAY REDUCED VISIBILITY FOR APPROXIMATELY ONE MINUTE. *KB
0710001
RELEASE OF STEERING GEAR STUB SHAFT BEARING KIT FOR SERVICE. *KB
0711003
DOORS ARE HARD TO CLOSE. *KB
0711004
SAFETY BELT LOCKING CONDITIONS. *KB
0707001
WHINE NOISE FROM REAR AXLE. VEHICLES WITH A 4.2L ENGINE. *KB
0711001
4.2L LL8 ENGINE - FLASHING AND/OR MIL LIGHT, ROUGH IDLE, MISFIRES DTC'S P0300, P0301, P0302, P0303, P0304, P0305, P0306. *KB
0611015
NOISE COMING FROM INSTRUMENT PANEL CLUSTER. *KB
0605004
DIAGNOSTIC TROUBLE CODE (DTC) P0757 SET, MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED, POOR PERFORMANCE OF TRANSMISSION, TRANSMISSION SLIPPING. *KB
0606003
REVISED SHOCK MODULE REPLACEMENT (SERVICE MANUAL REVISION). *KB
0611007
DISTORTION IN OUTER SURFACE OF VEHICLE GLASS. *KB
0612003
LOSS OF BLOWER MOTOR SPEEDS EXCEPT FOR LOW SPEED OR INOPERATIVE. MANUAL TEMP CONTROL, OR HEATER ONLY. *KB
0608002
TIRE CHARACTERISTICS OF ORIGINAL EQUIPMENT TIRES. *KB
0611006
PASSENGER OCCUPANT SENSING SYSTEM CONCERNS WITH CUSTOM UPHOLSTERY, ACCESORY SEAT HEATERS OR OTHER COMFORT ENHANCING DEVICES. *KB
0611012
REAR LIFTGATE BINDS, IMPROPER FIT. THIS MAY BE CAUSED BY BROKEN WELDS OR CRACKS THAT FORMED AROUND THE INNER TWO WELDS. *KB
0405002
INFORMATION ON 2-3 UP-SHIFT OR 3-2 DOWNSHIFT CLUNK SOUND. *TT
0605005
INFORMATION REGARDING AUTOMATIC TRANSMISSION SHIFT LOCK CONTROL FUNCTION. *TT
0404004
PROPER CONNECTION INFORMATION TO AVOID BLOWN 125 AMP FUSE AND VARIOUS INTERIOR ELECTRICAL SYSTEM CONDITION WHEN JUMP STARTING VEHICLE. *TT
0504003
DIAGNOSTIC INFORMATION ON HEADLAMPS FLICKER OR MOMENTARILY DIM WHILE DRIVING. *TT DIAGNOSTIC INFORMATION TO CLARIFY EFFECT OF SECONDARY AIR INJECTION SYSTEM ON HEADLAMP FLICKER. *TT
0604001
MALFUNCTION INDICATOR LAMP (MIL) ON CHECK ENGINE LIGHT ON, DTC P0526 SET. *TT
0604S001
DIAGNOSTIC INFORMATION TO CLARIFY EFFECT OF SECONDARY AIR INJECTION SYSTEM ON HEADLAMP FLICKER. *TT
0505005
SERVICE 4WD LIGHT ILLUMINATED, DIAGNOSTIC TROUBLE CODE (DTC) C0374 SET. *TT
0601001
OPERATING CHARACTERISTICS OF THE ELECTRO-VISCOUS (EV) FAN CLUTCH AND DIAGNOSTIC TIPS FOR COOLING FAN NOISE, DELAYED TRANSMISSION SHIFTS AND/OR ENGINE REVVING TOO HIGH. *TT
0604003
INTERMITTENT NO CRANK, NO START. *TT
06313003
ONSTART GENERATION 6 (DIGITAL) SYSTEM INOPERATIVE, HAS NO POWER, LED LIGHT NOT ON. *TT
0505013
DIAGNOSTIC TIPS FOR AUTOMATIC TRANSMISSION DTC P0756. *TT
0611003
DOOR LATCH FREEZING IN COLD TEMPERATURES. *TT
0405S008
DIAGNOSTIC INFORMATION ON DIAGNOSTIC TROUBLE CODE P0894 AND P1870. *TT
0604002
MALFUNCTION INDICATOR LAMP (MIL) ON/DIAGNOSTIC TROUBLE CODE(S) (DTC) P0300, P0171 AND P0174, MISFIRE DUE TO FUEL INJECTOR CONNECTORS CROSSED/SWAPPED/INCORRECTLY INSTALLED. *TT
0405005
DIAGNOSTIC TIPS FOR DIAGNOSTIC TROUBLE CODE (DTC) P0756 2-3 SHIFT VALVE PERFORMANCE. *TT
0505007
DIAGNOSTIC TROUBLE CODE (DTC) P0757 SET, MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED, POOR PERFORMANCE OF TRANSMISSION, TRANSMISSION SLIPPING. *TT
0506003
REVISED STABILIZER SHAFT REPLACEMENT (SERVICE MANUAL REVISION). *TT
0514004
ELIMINATING UNWANTED ODORS IN VEHICLES. *TT
00505006
MALFUNCTION INDICATOR LAMP (MIL) ON, TRANSMISSION STUCK IN SECOND OR THIRD GEAR, INSTRUMENT CLUSTER INOPERATIVE (VERIFY AND REPAIR SOURCE OF VOLTAGE LOSS IN TRANSMISSION SOLENOID POWER SUPPLY CIRCUIT). *TT
0505S006
MALFUNCTION INDICATOR LAMP (MIL) ON, TRANSMISSION STUCK IN SECOND OR THIRD GEAR, INSTRUMENT CLUSTER INOPERATIVE (VERIFY AND REPAIR SOURCE OF VOLTAGE LOSS IN TRANSMISSION SOLENOID POWER SUPPLY CIRCUIT. *JB
0505S012
4L60 AUTOMATIC TRANSMISSION DIAGNOSTIC INFORMATION ON HARSH 1-2 UPSHIFT. *JB
0501S007
INFORMATION ON USE OF KENT MOORE BOLT EXTRACTOR TOOL KIT EN-47702 FOR REMOVING CYLINDER HEAD OR MAIN BEARING CAP BOLTS ON INLINE ENGINES. *AK
0503S002
I/M READINESS AS PART OE EMISSION INSPECTION AND MAINTENANCE PROGRAM FOR OBD II VEHICLES. TO INCLUDE ISUZU I-280 AND I-350 2003 - 2005. *AK
0505002
DIAGNOSIS OF CRACK OR BROKEN TRANSMISSION CASE. *EH
0505009
1-2, 2-3, 3-4 SHIFT AND TORQUE CONVERTER CLUTCH (TCC) CHARACTERISTICS DURING COLD WEATHER OPERATION ON 4L60-E TRANSMISSIONS. TO INCLUDE 2006 ISUZU ASCENDER. *TT
0505010
ENGAGEMENT TIME OF ELECTRONICALLY CONTROLLED 4L60-E TRANSMISSIONS. *TT
0507002
SQUEAK, SQUEAL OR WHISTLE NOISE FROM FRONT. *TT
0501005
OIL LEAK UNDER EXTREME COLD TEMPERATURES. *TT
0508001
INFORMATION ON TIRE RADIAL FORCE VARIATION. TO INCLUDE 2006 ISUZU ASCENDER. *TT
0508002
COLD TIRE CHARACTERISTICS OF THE MANUFACTURER GM ORIGINAL EQUIPMENT TIRES. *TT
0512002
INTERMITTENT SLOW TO COOL HVAC PERFORMANCE CONCERNS IN HIGH AMBIENT TEMPERATURES AND/OR HIGH HUMIDITY CONDITIONS AFTER START UP, ESPECIALLY AT LOW ENGINE SPEEDS. *TT
0505003
THROTTLE TIP IN CLUNK NOISE AT LOW SPEEDS. *EH
0511008
RECONNECTION OF REAR WINDOW DEFROSTER CONTACT OR TAB. *EH
0511S005
LIFTGATE OR LIFTGATE GLASS BINDS, DOES NOT OPEN COMPLETELY, CHMSL HITS ROOF. *TT
0411S001
FRONT DOOR A-PILLAR WATER INTRUSION. *TT
0505004
SHIFT STABILIZATION FEATURE FOR HYDRAMATIC 4L60E TRANSMISSION. *EH
0505S002
SERVICE ENGINE SOON (SES) LIGHT ON, DIAGNOSTIC TROUBLE CODE (DTC) P0741, HARSH SHIFT, CRUISE CONTROL INOPERATIVE. *TT
0507001
LUBRICANT OIL LEAK FROM FRONT AREA OF VEHICLE. *EH
0507S001
LUBRICANT/OIL LEAK FROM FRONT AREA OF VEHICLE. *TT
0511002
DISTORTIOPN IN OUTER SURFACE OF VEHICLE GLASS. *EH
0511004
EXTERIOR LAMP CONDENSATION AND REPLACEMENT GUIDELINES. *TT
0513001
ERROR CODES ON RADIO DISPLAY THEIR CAUSE AND CORRECTIVE ACTION. *EH
0513002
BUZZ TYPE NOISE COMING FROM REAR SPEAKERS. *EH
0504001
VARIOUS INTERIOR ELECTRICAL CONCERNS IP GAUGES LIGHTING INOPERATIVE HVAC CONTROLS INOPERATIVE BLOWER MOTOR INOPERATIVE RADIO INOPERATIVE FLASHER INOPERATIVE. *EH
0511003
OUTSIDE REARVIEW MIRROR VIBRATION. *EH
0512001
INTERMITTENT A/C PERFORMANCE CONCERNS IN HIGH AMBIENT TEMPERATURES AND OR HIGH HUMIDITY CONDITIONS ESPECIALLY AT LOW ENGINE SPEEDS. *EH FINAL RELEASE. *TT
0510001
STEERING SYSTEM MOAN, GROAN, SHUDDER AND/OR VIBRATION TYPE NOISE DURING LOW SPEED TURNING MANEUVERS. *TT
0411S005
VEHICLE PAINT CODES. *TT
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.