Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1721000016 REV.B
Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked.
107418
SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
9100645
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
9100653
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
U90 - Parts Ordering
U90 - Parts Ordering
09-018-24
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
100096
U90 Parts Ordering
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1721000016
Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked, Set.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
S2325000007
MIL/check engine lamp comes on after performing U90 recall PCM software update.
9004542
Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
RecallU90
Emissions Recall U90 - Catalyst Efficiency
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
2101423
Power Transfer Unit (PTU) Broken Input Spline XJ1 Warranty Extension Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? 1720-00 - Output Speed Sensor Wheel Speed Rationality. ? P215C-00 - Output Shaft Speed Wheel Speed Correlation. This bulletin involves replacing the PTU assembly with an updated part.
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
91486
Warranty Bulletin D-23-10 (XJ1) Power Transfer Unit (PTU) - Select 2014 - 2017 Jeep Cherokee (KL)
91490
FCA Caribbean Warranty Bulletin ID-23-11 (XJ1) Power Transfer Unit (PTU) - Select 2014 - 2017 Jeep Cherokee (KL)
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
0900323
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ? Oil pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
09-003-23
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: Oil pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
88806
Warranty Bulletin D-23-01 - (XB1) 2.4L Engine ? Select 2014 - 2019 Jeep Cherokee (KL), 2017 - 2018 Jeep Compass (MP), 2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
09-013-22
2.4L Engine Oil Consumption Test The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2208000138
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S1523000016
A Rattle Or Creak Noise Is Heard From The Dual Pane Sunroof Area.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
V51
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
CSNW20
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W20
Powertrain Control Module.
9004401
DIFFERENTIAL, Rear Axle (KL 4WD w/DK2 = 1-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM · 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · 68550586A$ service RDMs have a 20 clutch plate design · Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA · If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540645AA for the 24 plate RDM with a new pump. · Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M
9004402
DIFFERENTIAL, Rear Axle (KL 4WD w/DK4 = 2-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM · 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design · Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. · If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540646AA for the 24-plate RDM with a new pump. · Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti
S1723000030
Service Electric Park Brake Message
W84
Customer Satisfaction Notification W84 Powertrain Software Update
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
2300521
Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.
2300521REVB
Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
23-005-21 Rev. A
Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.
21-017-21 Rev. A
Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following: Grinding noise coming from under the vehicle while driving. Vehicle will not move.
2101721
Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following: Grinding noise coming from under the vehicle while driving. Vehicle will not move.
21-017-21
Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following:Grinding noise coming from under the vehicle while driving. Vehicle will not move.
2101721-1
Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following:Grinding noise coming from under the vehicle while driving. Vehicle will not move.
2101721REVA
Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following:Grinding noise coming from under the vehicle while driving. Vehicle will not move.
2101721RevA
Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following:Grinding noise coming from under the vehicle while driving. Vehicle will not move.
74595
Warranty Bulletin D-21-07 (X89) Power Transfer Unit - 2014-2017 Jeep Cherokee (KL)
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
W20 Combo Phase4
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W84 Combo Phase3
Customer Satisfaction Notification W84 Powertrain Software Update
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
W20 Combo Phase3
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module (Revision 2)
W84 Combo Phase2
Customer Satisfaction Notification W84 Powertrain Software Update
W20 Combo Phase2
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W84 Combo Phase1
Customer Satisfaction Notification W84 Powertrain Software Update
23-005-21
Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replacedas well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle willneed to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100220
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
10-001-20
Airbag Warning Lamp (AWL) Illuminated B0028-13 and B0020-13 This bulletin involves inspecting and installing a jumper harness in the front seats if needed. Customers may experience a AWL illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in memory:B0028-13 - Right Side Seat Deployment Squib 1 - Circuit Open. B0020-13 - Left Side Seat Deployment Squib 1 - Circuit Open.
1000120
Airbag Warning Lamp (AWL) Illuminated B0028-13 and B0020-13 This bulletin involves inspecting and installing a jumper harness in the front seats if needed. Customers may experience a AWL illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in memory:B0028-13 - Right Side Seat Deployment Squib 1 - Circuit Open. B0020-13 - Left Side Seat Deployment Squib 1 - Circuit Open.
09-006-20 REV. B
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
0900620
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
9003968
CONDENSER, Air Conditioning CONDITION 1: If it is determined that the A/C compressor does not engage due to a refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
09-006-20 REV. A
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
09-006-20
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
S1823000053
Water Leak On Floor Near A Pillar
S2023000022
Window Slow To Raise Or Lower May Be Noisy
S1808000175
LED Front Fog Lamps Flicker Or Intermittently Light, Are Dim Or Inoperative. A U11E9, or B16FB-15 may be set
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
08-111-19 REV. A
RA3 and RA4 GPS Calibration Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
VB3
Revised Customer Satisfaction Notification VB3 ? Navigation Flash
VB3 REV1
Revised Customer Satisfaction Notification VB3 ? Navigation Flash
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
D-19-25
RRT 19-090 (Service Bulletin 08-111-19) 2013-2018 Multiple Vehicles RA3/RA4 Radio GPS Certification Error
D1925
RRT 19-090 (Service Bulletin 08-111-19) 2013-2018 Multiple Vehicles RA3/RA4 Radio GPS Certification Error
08-111-19
RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
0811119
RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
9004144
RADIO, MULTI Media For RA3 and RA4 8.4? radio concern of reoccurring update request pop-up on each key cycle after a radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.
08-089-19
Flash Over The Air (FOTA) Software Update RA3 and RA4 Radio This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
21-025-19
Nine-Speed Automatic Transmission (X80 Warranty Extension) This bulletin involves extending the warranty on the nine-speed automatic transmissions.
9003663
Side Window Air Deflectors There is a new (side window) deflector kit P/N released for Cherokee. P/N 82215206 is coded with usage on black trim models (sales code +MMF). Kit P/N for "bright" trim usage should be 82213940AB (sales code +MMP). Please make sure parts personnel understand the distinction between the 2 different applications before ordering.
08-094-17
RG3 RG4 RJ3 RJ4 Radio EnhancementsThis bulletin involves inspecting and updating the radio software, if required.?Navigation Failed? message is displayed (2014 MY WK and KL with RG4). Clock does not automatically update to local time (2014 MY WK and KL with RG4). Poor or no connection to cellular network (2014 MY WK and KL with RG4). HVAC temperature out of sync with radio display (2014 MY KL with RG4). Some Uconnect App remote commands do not execute with the vehicle (2014 MY WK and KL with RG4). Display goes blank/black (2014 MY WK and KL with RG4).Cyrillic keyboard is missing in phone book (2014 MY WK and KL with RG4).Incorrect speed limit on NAV speed camera indication (2014 MY WK and KL with RG4). Poor reception for AM/FM radio.Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played.SD, USB or BTSA modes may become non-functional for a given ignition cycle.Track names may be displayed twice in USB or SD media modes.Voice Recognition (VR) command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK)Vehicle only.DAB is inoperative.Wrong routing for addresses with a longitude between 0 and -1 degrees. Speed camera UK&Spain complaining that the speed camera feature was not available with the latest MY14 software.SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only).Battery drain due to the radio and cluster back-lighting staying on. Postal Code smart speller logic enhancements (EMEA markets only).AM/FM steering wheel mode switch button not working (LATAM markets only).Navigation Lockout Disable while vehicle is in motion (EMEA markets only).Removed network status indicators for SRT/APPS.VR says 'cancel' when starting (App) applications.iPod would not resume playing after a VR session or phone call.Removed the cell signal indicators in the SRT and Apps button on non-US vehicles.Rear camera may show a black screen for 3 secon
9003355
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
08-028-17 REV. B
RA3 and RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).
9003579
Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY: Prior to replacing ORC part numbers, please contact FCA engineering if ANY of the following Diagnostic trouble codes are Stored or Active in the ORC module: DTC: B223D-00 - OCM DTC Present DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair. FCA Engineering Contacts: Jay Nagle (ORC Module, Driver/passenger seat track position sensor, OCM for PF, KL or UF Vehicles ONLY) @ cell (248) 576-5657
0807117
This bulletin involves inspecting and updating the radio software, if required. A customer may experience one or more of the following conditions. Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 Only). HVAC temperature out of sync with radio display (KL vehicles). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Radio will lock up. Radio display screen is black or blank. Battery drain - due to radio remains on. HVAC temperature out of sync with radio display (KL vehicles). Track names may be displayed twice in USB or SD media modes. SD, USB or BTSA modes may become non-functional for a given ignition cycle. Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played. Navigation function may reset itself after using One-Shot VR. Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear. Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Park Sense tone continuously on. Radio display may show. Please insert USB Stick? Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to reverse. iPod would not resume playing after a VR session or phone call. Radio reset, screen lockup, blank screen or sluggish system.
9003755
Cover Kit Please note that if you are attempting to get the cover kit and it is not available the gasket is available as a separate part number in the kit which is 04753095AB.
0802817
This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
08-028-17
RA3 And RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
03-007-16
Front Of Vehicle Lateral Vibration During Low Speed Acceleration This bulletin involves replacing both front half shafts. The customer may describe a lateral wiggle, wobble, shake, shimmy, or shudder type vibration in the vehicle while accelerating at low speeds, typically between 16-32 kph (10-20 mph).
18-093-16 REV. A
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find, one or more of the following DTCs set in the PCM memory: P0116 - Coolant Temperature Sensor Performance. P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. U1424 - Implausible Engine Torque Signal Received. P1239 - Engine Oil Temperature Too Low, set in cold ambient temperatures. P0298 - Engine Oil Temperature Too High, set in cold ambient temperatures. P0300 - Multiple Cylinder Misfire, may set at a 1-2 upshift above 6000 RPM.In addition, some customers may experience one or more of the following conditions: Possible rough idle when engaging Drive while in 4 LOW after a cold start. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.
21-035-16
Transmission Shift And Drivability Enhancements For P0901-00. This bulletin involves performing transmission harness replacement per S55 recall.Both the PCM and TCM must be up to date for these changes to be effective after the transmission harness repair. Customers may experience a Malfunction Indicator Lamp (MIL) illumination after S55 recall TCM flash has been performed. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0901-00 - Clutch 1 Actuator Control Circuit Range Performance.
2500216
Replace Purge Control Valve Hose This bulletin involves replacing the purge control valve hose assembly. The customer may describe a slight noise coming from the engine compartment at the purge control valve area on the engine.
68194950
Dual Pane Sunroof and Sunshade Motor 1. Prior to ordering this part for loss of one touch function, please re-calibrate the sunroof motor per detailed instructions in Tech Connect to see if that corrects the issue. 2. 2014 / 2015 KL: Both the sunroof and sunshade motors must be at version REV 3.0.7. Motors replaced require the same level to calibrate successfully. If necessary, replace both motors to match for proper calibration.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
06-001-16 REV. A
Clutch Pedal Operation X62 Extended Warranty This bulletin involves the replacement of the hydraulic clutch master cylinder and reservoir hose. Some customers may experience a reduction in clutch pedal stroke.
D-160-1
(X62) Hydraulic Clutch Master Cylinder / Reservoir Hose - 2013-2015 Dodge Dart and 2014-2015 Jeep Cherokee (Rev. A) To announce an extended warranty on the Hydraulic Clutch Master Cylinder/ Reservoir Hose on the following vehicles: ? 2013-2015 Dodge Dart (PF) ? 2014-2015 Jeep Cherokee (KL)
68264880A
Parts.
68264880A$
Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY:~ Prior to replacing ORC part numbers, please contact FCA engineering if ANY of the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent, corroded, or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Malcolm Whitehouse (OCM Module - PF,KL, or UF Vehicles ONLY)@248-462-4703 or Malcolm.Whitehouse@fcagroup.com.~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com~
05047457A
Multi-Air Actuator Assembly For 2.4 Tigershark Engine ONLY: When attempting to diagnose P Codes related to the MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.
18-093-16
FLASH: POWERTRAIN DIAGNOSTIC AND SYSTEM ENHANCEMENTS THIS BULLETIN INVOLVES REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS) SET IN THE PCM MEMORY: · **P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. · P2610 - PCM INTERNAL ENGINE OFF TIMER PERFORMANCE. · U1424 - IMPLAUSIBLE ENGINE TORQUE SIGNAL RECEIVED.** · P1239 - ENGINE OIL TEMPERATURE TOO LOW, SET IN COLD AMBIENT TEMPERATURES. · P0298 - ENGINE OIL TEMPERATURE TOO HIGH, SET IN COLD AMBIENT TEMPERATURES. · P0300 - MULTIPLE CYLINDER MISFIRE, MAY SET AT A 1-2 UPSHIFT ABOVE 6000 RPM. IN ADDITION, SOME CUSTOMERS MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING CONDITIONS: · POSSIBLE ROUGH IDLE WHEN ENGAGING DRIVE WHILE IN 4 LOW AFTER A COLD START. · CORRECTED A GENERIC SCAN TOOL DISPLAY ISSUE REGARDING MODE 6 DATA ACCURACY.
18-060-16
Flash: Powertrain Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTCs) set in the PCM memory: · **P0335 - Crankshaft Position Sensor Circuit (Sales Code ERB). · P0300 - Multiple Cylinder Misfire (Sales Code ERB). · P0306 - Cylinder 6 Misfire. With automatic transmission (Sales Code ERB) (Sales Code DGJ). · P0456 - EVAP System Small Leak (Sales Code ERB).** · P2097- Downstream Fuel Trim System 1 Rich. · P2099- Downstream Fuel Trim System 2 Rich. · P0830- Clutch Pedal Switch ?A? Circuit. With manual transmission (Sales Code DEH). · P1239- Engine Oil Temperature Too Low. · U0140 - Lost Communication With Body Control Module. · Corrected a generic scan tool display issue regarding Mode 6 data accuracy.
08-024-16 REV. B
Flash: Radio Frequency Hub Module (RFHM) Enhancement This bulletin involves updating the RFHM with the latest available software. Customers may describe the instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (ten minutes or more).
68227808A$
REAR DIFFERENTIAL OR REAR DIFFERENTIAL ACTUATION MOTOR IF YOU ARE ATTEMPTING TO REPAIR A WHISTLING/HIGH PITCHED NOISE FROM THE REAR DIFFERENTIAL AREA FCA HAS RELEASED TSB 03-003-16 JUNE 21 TO ADDRESS THIS CONCERN
03-003-16
Drivetrain Control Module (DTCM) This bulletin involves replacing and reconfiguring the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience a constant high pitched whine coming from rear axle area.
68105583A$
PENTASTAR OIL FILTER ADAPTER BEFORE REPLACING THIS PART, PLEASE CALL ANY ONE OF THE FOLLOWING PEOPLE. ENGINEERING IS SEEKING INFORMATION REGARDING THIS PART.~ DYE MUST BE USED TO DETERMINE WHERE THE LEAK IS COMING FROM BEFORE REPLACING. ALSO PLEASE CHECK THE RECENTLY UPDATED SERVICE BULLETIN NUMBER 09-008-15. ~ FIRST: NICK MORAND CELL (248) 410-5078 - NICK.MORAND@FCAGROUP.COM SECOND: BOB JACKSON CELL (248) 944-0466 - BOB.JACKSON@FCAGROUP.COM THIRD: JOE LOVELL CELL (734 309-6467 - JOE.LOVELL@FCAGROUP.COM IF A RESPONSE IS NOT RECEIVED WITHIN 15 MINS, THEN PROCEED WITH THE NECESSARY REPAIR.
08-039-16 REV. A
Transmission Wiring Harness Repair Or Replacement For No Start Or Stiff Steering This bulletin involves inspecting the transmission wire harness and installing mastic patch. If rub through is visible replace wire harness. A small number of customers may experience a no start condition, stiff steering or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs): · U0131 - Lost Communication With Power Steering Control Module. · U0100-00 - Lost Communication With ECM/PCM. · P0512-00 - Starter Request Circuit.
08-039-16 REV.A
TRANSMISSION WIRING HARNESS REPAIR OR REPLACEMENT FOR NO START OR STIFF STEERING THIS BULLETIN INVOLVES INSPECTING THE TRANSMISSION WIRE HARNESS AND INSTALLING MASTIC PATCH. IF RUB THROUGH IS VISIBLE REPLACE WIRE HARNESS. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A NO START CONDITION, STIFF STEERING OR A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS): · U0131 - LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE. · U0100-00 - LOST COMMUNICATION WITH ECM/PCM. · P0512-00 - STARTER REQUEST CIRCUIT.
23-028-16
Rattle/Squeak From Rear Seat Armrest This bulletin involves inspecting the rear seat cushion frame for metal to metal contact, resulting in rattle noise. The customer may describe a rattle from the 60% portion of the rear seat. Metal to metal contact may be heard in either area.
23-027-16
Rattle/Squeak From Lower Rear Seat This bulletin involves inspecting the rear seat track adjuster bar speed nut fasteners. The customer may describe a rattling/ticking noise from rear seat track(s)/seat track adjuster bar area.
2302716
Rattle/Squeak From Lower Rear Seat This bulletin involves inspecting the rear seat track adjuster bar speed nut fasteners. The customer may describe a rattling/ticking noise from rear seat track(s)/seat track adjuster bar area.
08-064-16
Headlamp Leveling Switch Position Not Correct This bulletin involves running the wiTECH function: Configure BUX Headlamp Parameters. Customers may describe that the headlamp leveling switch positions are opposite of the actual headlamp positions (Fig. 1). For example, switch down position is headlamps up and vice versa.
1UT661X9A
ATX Shifter Assembly Description: For KL ONLY: Before this part is replaced for any issue please call John Tache on cell (248) 841-6711. If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any symptoms and DTCs identified with the scan tool and document them on the repair order.
68105583A
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
18-004-16 REV. A
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: 2015 KL Only · **P0335 - Crankshaft Position Sensor Circuit.** · P0456 - EVAP System Small Leak. · P0300 - Multiple Cylinder Misfire. · P0301 - Cylinder 1 Misfire. · P0302 - Cylinder 2 Misfire. · P0303 - Cylinder 3 Misfire. · P0304 - Cylinder 4 Misfire. · P2610 - PCM Internal Engine Off Timer Performance. · P1607 - PCM Internal Shutdown Timer Rationality. · U0402 - Implausible Data Received From TCM (ED6). · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050D - Cold Start Rough Idle. · P2172 - High Airflow/Vacuum Leak Detected. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only · P2172 - High Airflow/Vacuum Leak Detected. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. · P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions: · Cold Engine Startup Flare and Idle Surge (ED6). · Intermittent elevated engine RPM at start up. · Less than desired gear engagement in lower ambient temperatures. · Less than desired idle performance.
1800416REVA
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: 2015 KL Only · **P0335 - Crankshaft Position Sensor Circuit.** · P0456 - EVAP System Small Leak. · P0300 - Multiple Cylinder Misfire. · P0301 - Cylinder 1 Misfire. · P0302 - Cylinder 2 Misfire. · P0303 - Cylinder 3 Misfire. · P0304 - Cylinder 4 Misfire. · P2610 - PCM Internal Engine Off Timer Performance. · P1607 - PCM Internal Shutdown Timer Rationality. · U0402 - Implausible Data Received From TCM (ED6). · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050D - Cold Start Rough Idle. · P2172 - High Airflow/Vacuum Leak Detected. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only · P2172 - High Airflow/Vacuum Leak Detected. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. · P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions: · Cold Engine Startup Flare and Idle Surge (ED6). · Intermittent elevated engine RPM at start up. · Less than desired gear engagement in lower ambient temperatures. · Less than desired idle performance.
68141352A
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
24-007-16
Flash: HVAC System Enhancement This bulletin involves reprogramming the HVAC control module with the latest available software. The customer may describe one of the following: · **The radio temperature display does not match the HVAC controller temperature display. · After a temperature slide bar movement, the radio display shows the temperature slider waiting for about three seconds and then the slide bar jumps again. · Insufficient heating or cooling inside the vehicle.** · After the ignition has been turned off for over four minutes, the MTC HVAC controls change to a different setting. The temperature setting should remain where the temperature was last set at. When the temperature slider bar is left at mid way point or less, the setting will revert to a cooler setting depending on where it was set before.
2400716
Flash: HVAC System Enhancement This bulletin involves reprogramming the HVAC control module with the latest available software. The customer may describe one of the following: · **The radio temperature display does not match the HVAC controller temperature display. · After a temperature slide bar movement, the radio display shows the temperature slider waiting for about three seconds and then the slide bar jumps again. · Insufficient heating or cooling inside the vehicle.** · After the ignition has been turned off for over four minutes, the MTC HVAC controls change to a different setting. The temperature setting should remain where the temperature was last set at. When the temperature slider bar is left at mid way point or less, the setting will revert to a cooler setting depending on where it was set before.
0806016
Electronic parking brake module connector water intrusion.
68175510A
Rear trailing arm/link.
68175510A$
Rear trailing arm/link. Customer noise issue due to loose trailing link If a trailing link is damaged or noisy, please call Steve Lin at Cell 909-569-5117 prior to removing the part. If you do not hear from us within 15 minutes please continue with the repair.
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
08-054-16
RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. **Improvements: · Ability to communicate with Siri via UConnect. · Ability to press Voice Recognition (VR) button for more than one second.** A customer may experience one or more of the following conditions: · **Poor or no connection to cellular network (U.S. market only). · HVAC temperature out of sync with radio display (KL vehicles).** · Track names may be displayed twice in USB or SD media modes. · SD, USB or BTSA modes may become non-functional for a given ignition cycle. · Duplicate song titles may be displayed in USB mode. · Last track is displayed but next track is being played. · Navigation function may resets itself after using One-Shot VR. · Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. · GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. · A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. · Back-up camera image may be unclear or jittery/stutters at times. · Enables Via Mobile software features when released to consumers (U.S. market only). · Able to adjust audio balance / fade settings during a VR session. · Correct condition where user could not exit screen off mode. · Mute button status was not being displayed correctly. · Presets where not shown correctly or were deleted. · Enhancements to POI. · ParkSense tone continuously on. · Radio display may shows ?Please insert USB Stick?. · Enhancement made when video is display in radio when using PAL format video disks. · Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. · Navigation may not start or may lose position. · Rear camera may show a black screen for 3 seconds upon going to rev
08-029-16
Accessory Kit to Enhance Flat Tow Performance The customer may describe that their vehicle shakes or bounces while being flat towed. If the customer describes the symptom/condition listed above, a Mopar Accessory kit is available to improve flat tow towing behavior. Ensure that all instructions included in the kit (#K6862569), are followed during the install process.
08-029-16 REV. A
Accessory Kit to Enhance Flat Tow Performance The customer may describe that their vehicle shakes or bounces while being flat towed. If the customer describes the symptom/condition listed above, a Mopar Accessory kit is available to improve flat tow towing behavior. Ensure that all instructions included in the kit (#K6862569), are followed during the install process.
08-047-16
Flash: RK4 Radio Enhancements This bulletin involves updating the radio's software. The customer may describe one of the following condition(s): · After initially using radio with USB, radio will suddenly not play using USB. · Track names are displayed twice in USB and Secure Digital (SD) media modes. · Intermittent audio streaming while using USB and SD media devices.
0804716
RK4 Radio Enhancements
21-016-16
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · **P0887-00 - TCM Power Control Circuit High (Sales Codes ED6 and EHB). · P061B-00 - Internal Control Module Torque Calculation Performance (Sales Codes ED6 and EHB).** · P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. · P072F-00 - Stuck In Gear 4. · P076F-00 - Gear 7 shift Incorrect Ratio. · P0810-00 - Clutch Position Control Error. · P1CC9-00 - Unable To Engage Gear. · P0734-00 - Gear 4 Shift Incorrect Ratio. In addition, the following transmission shift and performance improvements are included in this software release: · **2-1 downshift quality when using Electronic Range Shifter (ERS) mode. · Garage shifts (Park to Reverse or Drive) (Sales Code EHB). · Poor 3-1 downshift quality when coasting to a stop (Sales Code ED6).** · 3-2 downshift delay while driving on inclines. · Overall coastdown shift quality. · Throttle response and performance feel. · Management and prevention of busy shifting. · Lift foot/change mind shift quality.
2101616
Transmission Diagnostic And Shift Enhancements.
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
08-039-16
Harness Repair Or Replacement For No Start Or Stiff Steering This bulletin involves inspecting the wire harness and installing mastic patch. If rub through is visible replace wire harness. A small number of customers may experience a no start condition, stiff steering or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs): · U0131 - Lost Communication With Power Steering Control Module. · U0100-00 - Lost Communication With ECM/PCM. · P0512-00 - Starter Request Circuit.
0803916
This bulletin involves inspecting the wire harness and installing mastic patch. If rub through
08-038-16
Flash: Electronic Parking Brake Module Enhancement This bulletin involves updating the Electronic Parking Brake (EPB) module software. The customer may describe the EPB does not engage with the ?Auto Apply? feature selected.
0803816
This bulletin involves updating the Electronic Parking Brake (EPB) module software.
R69
The Selective Catalytic Reduction (SCR) catalyst on about 11,400 vehicles is experiencing washcoat degradation, which may lead to the exceedance of exhaust emission standards.
S13
The Owner?s Manual and User Guide on about 99,000 of the above vehicles may have incorrect information regarding flat towing vehicles. Improper flat towing may result in vehicle shake while flat towing over rough roads.
0802916
The customer may describe that their vehicle shakes or bounces while being flat towed.
68246267A
Active Grill Shutter (AGS)
D-16-07
To announce the removal of the 9-speed 948TE transmission from the Powertrain Pre-Authorization Program
D1607
To announce the removal of the 9-speed 948TE transmission from the Powertrain Pre-Authorization Program
68317170A
9 Speed transaxle.
08-022-16
Accessory Kit to Enhance Flat Tow Performance The customer may describe that their vehicle shakes or bounces while being flat towed. Only perform this repair procedure if the customer?s VIN is listed in VIP or your RRT VIN list. Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all engine systems are functioning as designed. If DTCs or symptom conditions, other than the ones listed above are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin.
0802216
Accessory Kit to Enhance Flat Tow Performance.
21-008-16
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2100816
Power Transfer Unit (PTU) Motor Position Enhancements.
18-012-16
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
5LC23DX9A
Load Floor Handle.
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
68194950A$
Dual Pane Sunroof and Sunshade Motor Both the sunroof and sunshade motors must be at version REV 3.0.7. Motors replaced require the same REV level to calibrate successfully. If necessary, replace both motors to match for proper calibration.
07-001-16
Belt Tensioner Noise During Cold Start This bulletin involves replacing the belt tensioner. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0°C (32°F) and below.
06-001-16
Clutch Pedal Operation X62 Extended Warranty This bulletin involves the replacement of the hydraulic clutch master cylinder and reservoir hose. Some customers may experience a reduction in clutch pedal stroke.
0600116
Clutch Pedal Operation X62 Extended Warranty.
18-004-16
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination.
1800416
Powertrain Diagnostic And System Improvements.
D-16-01 X62
Warranty.
D1601X62
Warranty Bulletin
18-005-15 REV F
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): 2015 KL Only ? P0456 - EVAP System Small Leak. ? P0300 - Multiple Cylinder Misfire. ? P0301 - Cylinder 1 Misfire. ? P0302 - Cylinder 2 Misfire. ? P0303 - Cylinder 3 Misfire. ? P0304 - Cylinder 4 Misfire. ? P2610 - PCM Internal Engine Off Timer Performance. ? P1607 - PCM Internal Shutdown Timer Rationality. ? U0402 - Implausible Data Received From TCM (ED6). ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions: ? Cold Engine Startup Flare and Idle Surge (ED6). ? Intermittent elevated engine RPM at start up. ? Less than desired gear engagement in lower ambient temperatures. ? Less than desired idle performance. These conditions apply to 2015 model year vehicles only.
18-005-15 REV. F
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination.
1800515 REV F
Powertrain Diagnostic And System Improvements.
1800515REVF
Powertrain Diagnostic And System Improvements.
21-070-15
Flash: PTU Motor Position Enhancements This bulletin involves updating the software in the Power Transfer Unit (PTU), Rear Driveline Module (RDM) and Drivetrain Control Module (DTCM). A customer with a KL vehicle may experience difficulty shifting out of 4 Wheel Low (4WL). A customer with a UF vehicle may experience All Wheel Drive (AWD) not operating correctly. On further inspection the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? C1494-92-PTU Fork Position - Performance or Incorrect Operation. ? C1499-92-RDM Motor Position - Performance or Incorrect Operation. ? C1496-92-PTU Motor Position - Performance or Incorrect Operation.
2107015
PTU Motor Position Enhancements.
08-123-15
RA2 RG2 RJ2 Radio Enhancements This bulletin involves updating the radio's software. The customer may notice one or more of the following: ? Potential for inoperative or blank radio display. ? Radio displays message ?Please insert update USB? ? AM/FM presets lost over an ignition cycle. ? Ipod Synchronization will be incomplete causing the voice recognition to be inoperative. ? Display shows multiple USB media song titles in the browse menu. ? System incorrectly comes up in Aux mode. ? Unable to change CD tracks with steering wheel controls. ? May be able to change AM/FM frequencies while changing SXM frequencies. ? Display screen dim. ? Paired phone list is deleted after ignition cycle. ? Not able to pair phone. ? Unable to delete paired device from list. ? Removed the ability to pair phones while the vehicle is in motion. ? Voice command not able to play new text messages. ? SXM presets are lost at times. ? SXM disappeared and failed to re-register. ? Intermittently the wrong selected media is played. ? Noises (pops and cracks) for AM/FM. ? Audio controls are locked out after using Voice Recognition (VR). ? IPOD will not resume playing after phone call. ? IPOD ?Repeat? function is not turned on. ? IPOD songs not accessible through VR without ?genre?. ? IPOD shuffle does not continue after ignition cycle. ? Not able to restore to default setting. ? Potential for battery draw on E-Call function. ? Steering wheel control seek up/down function not working. ? Steering wheel control press and hold skipping channels. ? Intermittently the wrong pop-ups or displays is shown. ? Intermittently the phone or media will freeze. ? Presets or clock setting are lost after software updates. ? Climate ON/OFF pop-up will not longer appear. ? Can?t change media source to Disc. ? Wrong EQ setting being used. ? Mute function not working correctly. ? No audio on phone calls. Improvements ? VR command, p
1UT66QX9A
Part Description: ATX shifter assembly Issue Description: Before this part is replaced for any issue please call John Grzecki on cell (248) 379-0969. If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any symptoms and DTCs identified with the scan tool and document them on the repair order
06509898A
Part Description: Nut - Front Hub & Bearing Issue Description: Whenever replacing the front Hub & Bearing Halfshaft Nut, make sure to torque to proper spec of 150 ft/lbs (200 Nm) and crimp according to procedure in TechConnect. (This torrque is higher than other platforms). Failure to do so will result in eventual Hub & Bearing failure (noise).~
08-120-15
Intermittent No Start And/Or Instrument Cluster 4WD Indicator Lamp Illuminated This bulletin involves inspecting the wire harness for chafing and repairing or replacing the harness as necessary. The customer may describe the instrument cluster 4WD indicator lamp is illuminated and/or an intermittent no start condition.
D-15-21RevA
Powertrain Service Center-Pre-Authorization Program Updaves - 8-Speed, 9-Speed / TREMEC Assemblies Rev. A.
68257699A
Please contact Dennis Gauthier at cell (248) 613-9756 before replacing the part. If no response is received within 15 minutes, then please proceed with repair. ~
68317470A
Part Description: 2014 KL 9-Speed service transaxle with 2015 common hardware Issue Description: This 9-speed transaxle must be ordered thru Mopar?s Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM).~ This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.
D-15-21
Powertrain Service Center-Pre-Authorization Program Updaves - 8-Speed, 9-Speed / TREMEC Assemblies
08-103-15
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Track names may be displayed twice in USB or SD media modes. ? Voice Recognition command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK) Vehicle only. ? DAB (Digital Audio Broadcast) is inoperative. ? Wrong routing for addresses with a longitude between 0 and -1 degrees. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they sho
RL317270A
Part Description: 2014 KL 9-Speed service transaxle with 2015 common hardware Issue Description: This 9-speed transaxle must ordered thru Mopar?s Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM). This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.
RL317270A$
Part Description: 2014 KL 9-Speed service transaxle with 2015 common hardware Issue Description: This 9-speed transaxle must ordered thru Mopar?s Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM). This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.
18-005-15 REV-E
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs). 2015 KL Only ? U0402 - Implausible Data Received From TCM (ED6). ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions. These conditions apply to 2015 model year vehicles only. ? Cold Engine Startup Flare and Idle Surge (ED6). ? Intermittent elevated engine RPM at start up. ? Less than desired gear engagement in lower ambient temperatures. ? Less than desired idle performance.
18-005-15 REV. E
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs). 2015 KL Only ? U0402 - Implausible Data Received From TCM (ED6). ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions. These conditions apply to 2015 model year vehicles only. ? Cold Engine Startup Flare and Idle Surge (ED6). ? Intermittent elevated engine RPM at start up. ? Less than desired gear engagement in lower ambient temperatures. ? Less than desired idle performance.
08-097-15
FLASH: ABS Module Enhancements This bulletin involves updating the ABS Module software. New software is available to optimize Advanced Brake Assist (ABA) performance in low tractions situations.
SB-08-097-15
2014-2015 (KL)JEEP CHEROKEE AND 2015 (UF)CHRYSLER 200: THIS BULLETIN DEALS WITH LATEST SOFTWARE AVAILABLE TO OPTIMIZE ADVANCED BRAKE ASSIST PERFORMANCE IN LOW TRACTION SITUATIONS *CN
SB-08-091-15
JEEP CHEROKEE: ENGINE FAILS TO START UPON FIRST ATTEMPT, IPC MAY DISPLAY WRONG TRANSLATIONS, LOW BATTERY VOLTAGE AND/OR ENGINE STOP START NOT AVAILABLE. ENGINE CONTROL MODULE AND THE INSTRUMENT PANEL CLUSTER, IF REQUIRED, MADE NEED SOFTWARE UPGRADE *CN
03-003-15
Front Of Vehicle Lateral Vibration During Low Speed Acceleration This bulletin involves replacing both front half shafts. The customer may describe a lateral wiggle, wobble, shake, shimmy, or shudder type vibration in the vehicle while accelerating at low speeds, typically between 10-20 mph (16-32 kph).
SB-03-003-15
2014-2015 JEEP CHEROKEE: CUSTOMER MAY EXPERIENCE A LATERAL WIGGLE, SHAKE, WOBBLE, SHUDDER, OR SHIMMY TYPE VIBRATION IN VEHICLE WHILE ACCELERATING BETWEEN 10-20 MPH, AT LOW SPEEDS *CN
21-051-15
Flash: Improved Transmission Shift Quality This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or describe one or more of the following conditions. Upon further investigation, a technician may find the listed Diagnostic Trouble Code (DTC) stored in the TCM memory. ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? When driving on grades the 3-2 downshift is hard to achieve or not available. ? Poor shift quality during a 5-3 coast down.
SB-21-051-15
2014 JEEP CHEROKEE: A MALFUNCTION INDICATOR LAMP ILLUMINATION MAY BE EXPERIENCED BY CUSTOMERS. BULLETIN INCLUDES PROCEDURE ON FLASH REPROGRAMMING OF THE TRANSMISSION CONTROL MODULE WITH LATEST SOFTWARE *CN
21-008-15 REV-B
Transmission Shift Quality C-Clutch Snap Ring This bulletin involves removing the transmission, disassembling, and replacing the C-Clutch snap ring. A small number of customers may experience less than desired shift quality during a 5-4 downshift and/or Malfunction Indicator Lamp (MIL) Illumination. Upon further inspection, the technician may find Diagnostic Trouble Code (DTC) U0402 setting in the Powertrain Control Module (PCM) memory.
SB-21-008-15
JEEP/CHRYSLER: INFORMATION REGARDING AN ISSUE, ON SOME VEHICLES, WHEREBY DURING 5-4 DOWNSHIFTING, IS LESS THAN DESIRED AND MALFUNCTION INDICATOR LAMP (MIL) WILL ILLUMINATE AND REMOVING, DISASSEMBLING AND REPLACING THE C-CLUTCH SNAP RING AND TRANSMISSION. MODEL 2014-15 JEEP CHEROKEE, CHRYSLER 200. *PE UPDATED 10/15/15. *PE
18-005-15 REV-D
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs). 2015 KL Only ? U0402 - Implausible Data Received From TCM (ED6). ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions. These conditions apply to 2015 model year vehicles only ? Cold Engine Startup Flare and Idle Surge (ED6). ? Intermittent elevated engine RPM at start up. ? Less than desired gear engagement in lower ambient temperatures. ? Less than desired idle performance.
18-005-15 REV.B
CHRYSLER 2014-2015 JEEP CHEROKEE: VEHICLE EXPERIENCE A MALFUNCTION INDICATOR LAMP. THIS INVOLVES ERASING AND PROGRAMMING THE POWER CONTROL MODULE WITH LATEST SOFTWARE. *LJ UPDATED 9/4/15. *PE
08-072-15 REV-A
RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. A customer may experience, one or more of the following conditions. ? Track names may be displayed twice in USB or SD media modes. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? Navigation function may resets itself after using One-Shot Voice Recognition (VR). ? Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. ? GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. ? A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. ? Back-up camera image may be unclear or jittery/stutters at times. ? Enables Via Mobile software features when released to consumers. (U.S. market only) ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connecting. ? iPod would not resume playing after a VR session or phone call. ? Radio reset, screen lockup, blank screen or sluggish system respo
SB-08-072-15REVA
CERTAIN VEHICLES ARE HAVING RADIO, NAVIGATIONAL ISSUES REQUIRING SOFTWARE UPDATE. MODEL 2013-14. *PE
08-076-15
Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. A customer may describe that the ambient temperature display is slow to update. Upon further investigation the technician may find the Diagnostic Trouble Code (DTC) U1220-87 ?Lost Steering Lock Request Message - Missing Message?.
SB08-076-15
JEEP: BULLETIN ON SOFTWARE UPDATE FOR THE BODY CONTROL MODULE. AMBIENT TEMPERATURE DISPLAY IS SLOW TO UPDATE. *CN
08-072-15
RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. A customer may experience, one or more of the following conditions. ? Improved Radio security protection to reduce the potential risk of unauthorized and unlawful access to vehicle systems (U.S. Market Only). ? Track names may be displayed twice in USB or SD media modes. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? Navigation function may resets itself after using One-Shot Voice Recognition (VR). ? Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. ? GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. ? A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. ? Back-up camera image may be unclear or jittery/stutters at times. ? Enables Via Mobile software features when released to consumers. (U.S. market only) ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connec
08-067-15
RM4 Radio Enhancements (Japan Only) This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: ? Digital TV, television display screen may be blurry. ? Song names displayed twice in USB and SD media modes. ? Radio may displays or voice prompt ?Please check ETC device? (Electronic Toll Collection). ? Poor navigation guides through overpass or underpasses, multi-level intersections. ? Navigation Turn-by-turn guidance setting may be cleared after ignition is cycled. ? Navigation may reset while driving.
08-016-15 REVA
Poor Radio Reception This bulletin involves replacing the satellite antenna if needed. A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies to 2014-2015 WD, WK or KL Vehicles. A customer may experience a popping noise when listening to AM stations.
21-043-15
Flash: Transmission Shift and Diagnostic Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination on vehicles equipped with a 948TE 9 speed automatic transmission (sales code DFH or DFJ). Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. ? P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P072F-00 - Stuck in Gear 4 ? P076F-00 - Gear 7 shift incorrect ratio ? P0810-00 - Clutch position control error ? P1CC9-00 - Unable to engage gear ? P0734-00 - Gear 4 shift incorrect ratio ? P061B-00 - Internal control module torque calculation performance In addition, the following transmission shift and performance improvements are included in this software release. ? 3-2 downshift delay while driving on inclines. ? Garage shifts (Park to Reverse or Drive). ? Overall coastdown shift quality. ? Throttle response and performance feel. ? Management and prevention of busy shifting. ? Lift foot/change mind shift quality.
08-061-15
Incorrect cruise control set speed is diplayed.
0806115
Incorrect cruise control set speed is diplayed.
03-002-15
Drone noise at steady state engine RPM.
0300215
Drone noise at steady state engine RPM.
23-021-15
Squeak Noise Coming From The Rear Seat This bulletin involves applying tape to the rear seat track J-rail. The customer may describe a squeak noise coming from the rear seat, typically when the seat is unoccupied. The noise may be caused by metal to metal contact of the rear seat track J-rail.
2302115
Squeak Noise Coming From The Rear Seat This bulletin involves applying tape to the rear seat track J-rail. The customer may describe a squeak noise coming from the rear seat, typically when the seat is unoccupied. The noise may be caused by metal to metal contact of the rear seat track J-rail.
2103315
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software followed by a drive validation. The following software enhancement, for the 948TE 9-speed transmission, is being released to improve diagnostics for the following Diagnostic Trouble Codes (DTCs): ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P0887 - TCM Power Control Circuit High ? P1720 - Output Speed Sensor-Wheel Speed Rationality ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective ? P215C - Output Shaft Speed Wheel Speed Correlation ? U0401 - Implausible Data Received From ECM-PCM The software also enables DTC P07A7 - Transmission Friction Element C Stuck On to set in the case of a dislodged C-clutch snap-ring.
2301615
Front Passenger Fold Flat Seat Back Inoperative This bulletin involves adjusting the passenger fold flat seat back cable. The customer may describe that the passenger front fold flat seat back is inoperative and the seat back will not fold down.
23-016-15
Front Passenger Fold Flat Seat Back Inoperative This bulletin involves adjusting the passenger fold flat seat back cable. The customer may describe that the passenger front fold flat seat back is inoperative and the seat back will not fold down.
18-005-15 REVC
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs). 2015 KL Only: ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only: ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions. These conditions apply to 2015 model year vehicles only: ? Intermittent elevated engine RPM at start up. ? Less than desired gear engagement in lower ambient temperatures. ? Less than desired idle performance.
21-015-15 REVA
Flash: C1499-92-RDM Motor Position C1496-92-PTU Motor Position This bulletin involves updating the software in the Power Transfer Unit (PTU), Rear Driveline Module (RDM) and Drivetrain Control Module (DTCM). A customer with a KL vehicle may experience difficulty shifting out of 4 Wheel Low (4WL). A customer with a UF vehicle may experience All Wheel Drive (AWD) not operating correctly. On further inspection the Technician my find Diagnostic Trouble Codes (DTCs): ? C1499-92-RDM Motor Position - Performance or Incorrect Operation. ? C1496-92-PTU Motor Position - Performance or Incorrect Operation.
21-015-15REV.A
CHRYSLER JEEP CHEROKEE 2014-2015, CHRYSLER 200: BULLETIN INFORMATION INVOLVING UPDATING THE SOFTWARE IN THE POWER TRANSFER UNIT, REAR, DRIVELINE MODULE & DRIVETRAIN CONTROL MODULE. *LJ
07-002-15 REV. A
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
18-005-15 REV. B
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low.
9003024
Part Description: Steering Column Control Module - Clockspring Issue Description: Please note the Steering angle sensor is not in the SCCM/Clockspring on 2014 and newer Cherokee.~ Refer to section 19 Steering gear for more detail on the steering angle sensor.
21-015-15
Flash: C1499-92-RDM Motor Position C1496-92-PTU Motor Position This bulletin involves updating the software in the Power Transfer Unit (PTU), Rear Driveline Module (RDM) and Drivetrain Control Module (DTCM). A customer with a (KL) vehicle may experience difficulty shifting out of 4 Wheel Low (4WL). A customer with a (UF) vehicle may experience All Wheel Drive (AWD) not operating correctly. On further inspection the Technician my find Diagnostic Trouble Codes (DTCs): ? C1499-92-RDM Motor Position - Performance or Incorrect Operation. ? C1496-92-PTU Motor Position - Performance or Incorrect Operation.
02-004-15
Cold Temperature Squeak/Creak Noise While Turning The Steering Wheel This bulletin involves applying Nye® lubricant to the front strut mounts. Customer may describe a creak or squeak noise while turning the steering wheel. Noise is typically more noticeable during cold temperatures below 4°C (40°F), noise may go away when temperature warms up.
0200415
Cold Temperature Squeak/Creak Noise While Turning The Steering Wheel This bulletin involves applying Nye® lubricant to the front strut mounts. Customer may describe a creak or squeak noise while turning the steering wheel. Noise is typically more noticeable during cold temperatures below 4°C (40°F), noise may go away when temperature warms up.
08-016-15
Poor Radio Reception This bulletin involves replacing the satellite antenna if needed. A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.
0801615
Poor Radio Reception This bulletin involves replacing the satellite antenna if needed. A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.
1400115
Diesel Fuel Filter Weepage in Extreme Cold Conditions This bulletin involves installing a new fuel/ water separator filter. Diesel fuel weepage from bottom of the vehicle when a cold soaked vehicle is started at temperatures of -13 F (-25 C) or below when using artic diesel fuel or a cold weather diesel fuel additive.
08-013-15
Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: ? A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. ? Intermittent No Start condition Without any DTCs (Vehicles with steering column lock, only). ? U1220-87 - Lost Steering Lock Request Message - Missing Message. ? U1517-87 - Body Controller Secret Code - Missing Message. ? B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. ? Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH (3 KPH), (Manual Transmission only). ? Puddle Lamps will not turn off when the engine is started, (Manual Transmission only). NOTE: If battery system DTC P0562 Battery/System Voltage Low or P0563 Battery/System Voltage High are set, normal charging system diagnostics needs to be performed.
0801315
Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: ? A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. ? Intermittent No Start condition Without any DTCs (Vehicles with steering column lock, only). ? U1220-87 - Lost Steering Lock Request Message - Missing Message. ? U1517-87 - Body Controller Secret Code - Missing Message. ? B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. ? Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH (3 KPH), (Manual Transmission only). ? Puddle Lamps will not turn off when the engine is started, (Manual Transmission only). NOTE: If battery system DTC P0562 Battery/System Voltage Low or P0563 Battery/System Voltage High are set, normal charging system diagnostics needs to be performed.
21-001-15
Service Bulletin/RRT 21-001-15/15-003 Superseded By Customer Satisfaction Notification (CSN) R01 Refer to service procedures outlined in CSN R01.
21-001-15 REV. A
Service Bulletin/RRT 21-001-15/15-003 Superseded By Customer Satisfaction Notification (CSN) R01 Refer to service procedures outlined in CSN R01.
2100115
Service Bulletin/RRT 21-001-15/15-003 Superseded By Customer Satisfaction Notification (CSN) R01 Refer to service procedures outlined in CSN R01.
2100115REVA
Service Bulletin/RRT 21-001-15/15-003 Superseded By Customer Satisfaction Notification (CSN) R01 Refer to service procedures outlined in CSN R01.
9003029
Part Description: Steering Column and Seals. Issue Description: If the customer complains of a steering column squeak when turning the wheel in low speed maneuvers (parking lot, driveway) in cold weather, the following inspection procedure will assist in preventing a misdiagnosis.~ Inspect the suspension front coil spring to isolators. This can be done by first letting the vehicle cold soak. The noise is normally heard in temperatures ranging from 15- 40 degrees (F). With one person in the vehicle turning the steering wheel, place your hand on the front spring. If a vibration is felt when the noise is heard by the vehicle occupant, the issue is from the front suspension ? not in the steering column. Do not service the steering column.
21-008-15 REV. A
Transmission Shift Quality C-Clutch Snap Ring This bulletin involves removing the transmission, disassembling, and replacing the C-Clutch snap ring. A small number of customers may experience less than desired shift quality during a 5-4 downshift and/or Malfunction Indicator Lamp (MIL) Illumination. Upon further inspection, the technician may find Diagnostic Trouble Code (DTC) U0402 setting in the Powertrain Control Module (PCM) memory.
21-008-15A
Transmission Shift Quality C-Clutch Snap Ring This bulletin involves removing the transmission, disassembling, and replacing the C-Clutch snap ring. A small number of customers may experience less than desired shift quality during a 5-4 downshift and/or Malfunction Indicator Lamp (MIL) Illumination. Upon further inspection, the technician may find Diagnostic Trouble Code (DTC) U0402 setting in the Powertrain Control Module (PCM) memory.
2100815-1
Transmission Shift Quality C-Clutch Snap Ring This bulletin involves removing the transmission, disassembling, and replacing the C-Clutch snap ring. A small number of customers may experience less than desired shift quality during a 5-4 downshift and/or Malfunction Indicator Lamp (MIL) Illumination. Upon further inspection, the technician may find Diagnostic Trouble Code (DTC) U0402 setting in the Powertrain Control Module (PCM) memory.
2100815REVA
Transmission Shift Quality C-Clutch Snap Ring This bulletin involves removing the transmission, disassembling, and replacing the C-Clutch snap ring. A small number of customers may experience less than desired shift quality during a 5-4 downshift and/or Malfunction Indicator Lamp (MIL) Illumination. Upon further inspection, the technician may find Diagnostic Trouble Code (DTC) U0402 setting in the Powertrain Control Module (PCM) memory.
21-010-15
9 Speed Tutorial Awareness This bulletin provides awareness of 9 Speed Tutorial.
2101015
9 Speed Tutorial Awareness This bulletin provides awareness of 9 Speed Tutorial.
21-008-15
Transmission Shift Quality C-Clutch Snap Ring This bulletin involves removing the transmission, disassembling, and replacing the C-Clutch snap ring. A small number of customers may experience less than desired shift quality during a 5-4 downshift and/or Malfunction Indicator Lamp (MIL) Illumination. Upon further inspection, the technician may find Diagnostic Trouble Code (DTC) U0402 setting in the Powertrain Control Module (PCM) memory.
2100815
Transmission Shift Quality C-Clutch Snap Ring This bulletin involves removing the transmission, disassembling, and replacing the C-Clutch snap ring. A small number of customers may experience less than desired shift quality during a 5-4 downshift and/or Malfunction Indicator Lamp (MIL) Illumination. Upon further inspection, the technician may find Diagnostic Trouble Code (DTC) U0402 setting in the Powertrain Control Module (PCM) memory.
SB-21-001-15
CHRYSLER/JEEP: TSB CONTAINS AN OWNER NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. TO PREVENT C-CLUTCH SNAP FROM DISLODGING, A NEW SOFTWARE ENHANCEMENT IS RELEASED TO CHANGE THE CHARACTERISTICS OF CLUTCH APPLICATION BY REPROGRAMMING TRANSMISSION CONTROL MODULE (TCM) AND POWERTRAIN CONTROL MODULE (PCM). MODEL 2014-15 JEEP CHEROKEE, 2015 CHRYSLER 200. *PE UPDATED 06/29/15. *LJ
21-007-15
9 Speed Transmission Shift Enhancements - Adaptation Learn Procedure This bulletin involves performing a subjectivity shift quality rating and performing the transmission adaptation learn procedure if required. Customers may indicate that their transmission shift quality does not meet their expectations.
11-001-15
Sputter Type Noise Emitted From Exhaust This bulletin involves inspecting and replacing the resonator if required. The customer may notice a sputter type noise coming from under the vehicle.
08-011-15
B2128-17 - Sensor Supply Voltage - Circuit Voltage Above Threshold And/Or U045A-86 - Implausible Data Received From Parking Assist Module - Signal Invalid This bulletin involves updating the Park Assist Module (PAM) software. Some customers may comment that when pressing the Parallel and/or Perpendicular Park Assist button when the vehicle is stopped (during stop/start event) it will not illuminate. Additionally the customer may experience a false park assist detection. This is caused by ground reflections, on vehicles equipped with XH3 or XH4. If the customer wish to do a Parallel and/or Perpendicular Park Assist (PPPA) maneuver and they push the PPPA button, then the cluster may display, "Active ParkSense Temporarily Unavailable?. This is an intermittent condition and will only last for one key cycle. On further inspection the technician may find DTC U045A-86 - Implausible Data Received From Parking Assist Module - Signal Invalid and/or a B2128-17 - Sensor Supply Voltage - Circuit Voltage Above Threshold set in the PAM.
18-005-15 REV. A
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low.
18-005-15
Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low.
07-002-15
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
08-111-14
Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. Without any DTCs (Vehicles with steering column lock, only). U1220-87 - Lost Steering Lock Request Message - Missing Message. U1517-87 - Body Controller Secret Code - Missing Message. B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH (3 KPH), (Manual Transmission only). Puddle Lamps will not turn off when the engine is started, (Manual Transmission only).If battery system DTC P0562 Battery/System Voltage Low or P0563 Battery/System Voltage High are set, normal charging system diagnostics needs to be performed.
0811114
Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the
18-060-14 REV. C
Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). * P2172 - High Airflow/Vacuum Leak Detected. * Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2015 KL Vehicles equipped with a 3.2L engine (Sales Code EHB) built on or before November 20, 2014 (MDH 1120XX). * P2067- Fuel Level Sensor 2 Circuit Low (International Only). * Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). * P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. * P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range.
18-060-14REV.C
DODGE 2014-2015 JEEP CHEROKEE: DUE TO UPGRADED NEW REVISIONS OF REPROGRAMMING AND ERASING SOFTWARE FOR POWERTRAIN CONTROL MODULE (PCM). *LJ UPDATED 05/01/15. *LJ
1806014REVC
Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2015 KL Vehicles equipped with a 3.2L engine (Sales Code EHB) built on or before November 20, 2014 (MDH 1120XX). ? P2067- Fuel Level Sensor 2 Circuit Low (International Only). ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range.
1806014a
Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following
09-005-14 REV.A
Service Bulletin/RRT 09-005-14/14-071 Superseded By Customer Satisfaction Notification (CSN) P55 Refer to service procedures outlined in CSN P55.
09-005-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0900514
Service Bulletin/RRT 09-005-14/14-071 Superseded By Customer Satisfaction Notification (CSN) P55 Refer to service procedures outlined in CSN P55.
0900514REVA
Service Bulletin/RRT 09-005-14/14-071 Superseded By Customer Satisfaction Notification (CSN) P55 Refer to service procedures outlined in CSN P55.
21-018-14 REV. B
Flash: Transmission Shift and Diagnostic Enhancements This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software.Vehicles that are being updated from TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number) will not require the 9 Speed Adaptation Drive Learn Procedure to be performed. However, vehicles being updated from any other software part number will require the Adaptation Drive Learn Procedure to be performed. Refer to all applicable published service bulletins regarding the 9 Speed Adaptation Drive Learn procedure for detailed repair procedures and labor times. Diagnostic Trouble Code (DTC) robustness improvements are included in this software release. These improvements apply to the following DTCs: P072F- Stuck in Gear 4 P076F- Gear 7 shift incorrect ratio P0810- Clutch position control error P1CC9- Unable to engage gear P0734- Gear 4 shift incorrect ratio P061B- Internal control module torque calculation performance
2101814
Flash: Transmission Shift and Diagnostic Enhancements This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software.Vehicles that are being updated from TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number) will not require the 9 Speed Adaptation Drive Learn
2101814REVB
Flash: Transmission Shift and Diagnostic Enhancements This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software.Vehicles that are being updated from TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number) will not require the 9 Speed Adaptation Drive Learn Procedure to be performed. However, vehicles being updated from any other software part number will require the Adaptation Drive Learn Procedure to be performed. Refer to all applicable published service bulletins regarding the 9 Speed Adaptation Drive Learn procedure for detailed repair procedures and labor times. Diagnostic Trouble Code (DTC) robustness improvements are included in this software release. These improvements apply to the following DTCs: P072F- Stuck in Gear 4 P076F- Gear 7 shift incorrect ratio P0810- Clutch position control error P1CC9- Unable to engage gear P0734- Gear 4 shift incorrect ratio P061B- Internal control module torque calculation performance
0800314REVA
Integrated Center Stack Missing Buttons This bulletin involves replacing the integrated center stack (ICS) bezel. Summit Edition (sales code AAU) vehicles built with incorrect ICS, missing buttons for Front & Rear Park Assist (sales code XAG) and Forward Collision Warning (sales code LSR).
2100314REVA
Flash: 845RE Transmission Shift Enhancements, 2-1 Downshift This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB)
08-018-14
Flash: Instrument Cluster Shows "Low Battery Voltage" Erroneously This bulletin involves flashing the Instrument Cluster with a new software. The customer may experience ?Low Battery Voltage? text message shown erroneously in the EVIC.
08-018-14 REV.A
Flash: Instrument Cluster Shows "Low Battery Voltage" Erroneously This bulletin involves flashing the Instrument Cluster with a new software. The customer may experience "Low Battery Voltage" text message shown erroneously in the EVIC.
08-050-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-102-14
Flash: IPC Software Enhancements This bulletin involves upgrading the software in the Instrument Panel Cluster (IPC). The customer may experience one or all of the following: - IPC may display the wrong translations in all languages ( APAC Market excluded). - ?Low Battery Voltage? text message shown erroneously in the EVIC.
0801814
Instrument Cluster Shows "Low Battery Voltage" Erroneously.
0810214
IPC Software Enhancements
18-060-14
Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2015 KL Vehicles equipped with a 3.2L engine (Sales Code EHB) built on or before October 21, 2014 (MDH 1021XX). ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range.
18-060-14 REV. B
Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). * P2172 - High Airflow/Vacuum Leak Detected. * Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2015 KL Vehicles equipped with a 3.2L engine (Sales Code EHB) built on or before October 21, 2014 (MDH 1021XX). * Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). * P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. * P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range.
1806014-1
Diagnostic And System Improvements
21-027-14
Service Bulletin/RRT 21-027-14/14-070 Superseded By Customer Satisfaction Notification (CSN) P56 Refer to service procedures outlined in CSN P56.
21-027-14 REV. A
Service Bulletin/RRT 21-027-14/14-070 Superseded By Customer Satisfaction Notification (CSN) P56 Refer to service procedures outlined in CSN P56.
21-027-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-060-14 REV. A
Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2015 KL Vehicles equipped with a 3.2L engine (Sales Code EHB) built on or before October 21, 2014 (MDH 1021XX). ? Improved software to enable Transmission Control Module (TCM) quick learnenhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range.
18-060-14-1
Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2015 KL Vehicles equipped with a 3.2L engine (Sales Code EHB) built on or before October 21, 2014 (MDH 1021XX). ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range.
18-060-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
09-006-14
Blue Smoke At Start Up This bulletin involves replacing the cylinder head, if required. Customers may notice blue smoke coming from the tail pipe at start up.
0900614
Blue Smoke At Start Up
1806014
Diagnostic and System Improvements
08-021-14 REV. C
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. DAB (Digital Audio Broadcast) is inoperative. Wrong routing for addresses with a longitude between 0 and -1 degrees. Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. DAB preset list on the top of the screen doesn't change while scrolling with steering controls. Rear view camera jitter. Tuner reception software enhancements. HVAC temperature control enhancements. SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). Battery drain due to the radio and cluster back-lighting staying on. Postal Code smart speller logic enhancements (EMEA markets only). AM/FM steering wheel mode switch button not working (LATAM markets only). Navigation Lockout Disable while vehicle is in motion (EMEA markets only). Removed network status indicators for SRT/APPS. Voice Recognition (VR) says 'cancel' when starting (App) applications. iPod would not resume playing after a VR session or phone call. Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. rear camera may show a black screen for 3 seconds upon going to reverse. Navigation would not start or would lose position. Removal of parental control under Apps menu. Turn by Turn navigation in the cluster set to ON by default. Transfer button does not pick-up and transfer incoming call. Some Russian letters are caps when they should be lower-case. Touch screen locks up in navigation, when Russian is selected. Address search availably when the vehicle is moving (EMEA markets only). VR messages in Spanish talks to fast. Recognition enhancement for Russian VR. Hands free audio too low for non-amp vehicle (KL). Intermittently Registration expired pop-up appears on display screen. Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). Incorrect time to destination
0802114
RG3 RG4 RJ3 RJ4 Radio Enhancements
08-094-14
Engine Does Not Start at The First Attempt This bulletin involves upgrading the software in the Electronic Steering Lock (ESL). The customer may experience where the engine fails to start at the first attempt. Initial cranking is inhibited but able to start/crank on the second attempt. On further inspection the technician may find DTC B1A92-09- ?Steering Lock Motor - Component Failures? stored in the ESL Module.
0809414
Engine Does Not Start at The First Attempt
18-054-14
Intermittent Extended Crank, Long Crank Time. This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.
1805414
Intermittent Extended Crank, Long Crank Time.
21-032-14
9 Speed Transmission Shift Enhancements - Adaptation Learn Procedure This bulletin involves performing a subjectivity shift quality rating and performing the transmission adaptation learn procedure if required. Customers may indicate that their transmission shift quality does not meet their expectations.
2103214
9 Speed Transmission Shift Enhancements - Adaptation Learn Procedure
08-076-14 REV. A
Flash: ECM and IPC Software Enhancements This bulletin involves upgrading the software in the Engine Control Module (ECM) and the Instrument Panel Cluster (IPC). The customer may experience one or all of the following: - The engine fails to start at the first attempt using the Keyless Ignition Node (KIN) button. - IPC may display the wrong translations in all languages ( APAC Market excluded). - Confusing the vehicle start logic condition based on the vehicle standing in the Start and Stop mode. - ?Stop/Start Not Ready-Battery Charging? maybe displayed erroneously. - ?Low Battery Voltage? text message shown erroneously in the EVIC.
08-076-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0807614
ECM and IPC Software Enhancements
30-001-14 REV A.
CHRYSLER: DODGE DURANGO, GRAND CHEROKEE REPAIRS FOR THE FOLLOWING VEHICLES ARE TO BE PERFORMED ACCORDING TO THIS NOTICE. FRONT HALF SHAFT CLAMPS HAVE BEEN INSTALLED INCORRECTLY. *LJ
81-016-1053
CHRYSLER: 2014-2015 JEEP CHEROKEE, CHRYSLER 200 TRANSMISSION MAY NOT ALLOW THE TRANSAXLE TO SHIFT GEAR DUE TO TRANSMISSION CONTROL MODULE SOFTWARE. *LJ SEE DOCUMENT SEARCH BUTTON FOR OWNERS LETTER *LJ
08-084-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-081-14
MIL Illumination DTC U11E9 After Fascia Removal This bulletin involves confirming that the Active Grille Shutter (AGS) electrical harness connector is properly connected.
0808114
MIL Illumination DTC U11E9 After Fascia Removal This bulletin involves confirming that the Active Grille Shutter (AGS) electrical harness connector is properly connected.
08-076-14
Engine Does Not Start at the First Attempt This bulletin involves upgrading the software in the Powertrain Control Module (PCM). A customer may experience, the engine fails to start at the first attempt using the Keyless Ignition Node (KIN) button.
08-077-14
Flash: Key Programming Improvements This bulletin involves updating the Radio Frequency HUB (RF HUB) with new software. The technician may have issues when trying to program new keys or installing Mopar remote start kits. Before programming keys make sure the RF HUB has the latest software in it.
0807714
Flash: Key Programming Improvements This bulletin involves updating the Radio Frequency HUB (RF HUB) with new software. The technician may have issues when trying to program new keys or installing Mopar remote start kits. Before programming keys make sure the RF HUB has the latest software in it.
09-005-14
Replace Engine Drive Belt This bulletin involves replacing the engine serpentine belt. The engine drive belt may exhibit a noise.
2102714
Flash: MIL Illumination For P0733, P061B, P1DB8 This bulletin involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available. ? P0733 Gear 3 Shift Incorrect Ratio ? P061B Internal Control Module Torque Calculation Performance ? P1DB8 Due to erroneous DTC ? Improved downshift response in Adaptive Cruise Control (ACC) operation when there is a driver override.
18-031-14 REV. A
Flash: MIL Illumination P1239, P0298- Engine Oil Temperature Too Low Or High, P0300 Multiple Cylinder Misfire, Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P1239 - Engine Oil Temperature Too Low, set in cold ambient temperatures. P0298 - Engine Oil Temperature Too High, set in cold ambient temperatures. P0300 - Multiple Cylinder Misfire, may set at a 1-2 upshift above 6000 RPM. Possible rough idle when engaging Drive while in 4 LOW after a cold start .The following system improvements have also been included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy.
18-031-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
1803114
Flash: MIL Illumination P1239, P0298- Engine Oil Temperature Too Low Or High, P0300 Multiple Cylinder Misfire, Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P1239 - Engine Oil Temperature Too Low, set in cold ambient temperatures. P0298 - Engine Oil Temperature Too High, set in cold ambient temperatures. P0300 - Multiple Cylinder Misfire, may set at a 1-2 upshift above 6000 RPM. Possible rough idle when engaging Drive while in 4 LOW after a cold start .The following system improvements have also been included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy.
18-046-14
Flash: MIL Illumination P219A-Air Fuel Ratio Cylinder Imbalance Bank 1 This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that Diagnostic Trouble Code P219A-Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM.
09-003-14
Strong Vibration And Loud Boom When Placed In Reverse At High Idle Speed This bulletin involves replacing the rear engine mount. Strong vibration and loud boom sound when placed in reverse during cold high idle (over 1100 RPM) and engine coolant temperature less than 70 degrees Fahrenheit (21 degrees Celsius).
02-001-14 REV. B
Cold Temperature Squeak/Creak Noise While Turning The Steering Wheel This bulletin involves applying Nye® lubricant to the front strut mounts. Customer may describe a creak or squeak noise while turning the steering wheel. Noise is typically more noticeable during cold temperatures below 4°C (40°F), noise may go away when temperature warms up.
02-001-14REV.B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-064-14
RJ4 Navigation Enhancements This bulletin involves inspecting and updating the radio software, if required. A customer may experience, one or more of the following conditions. Peru maps not available. When using navigation route guidance with Spanish language selected the customer will have English voice guidance presented when it should be in Spanish.
08-021-14 REV. B
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they should be lower-case. ? Touch screen locks up in navigation, when Russian is selected. ? Address search availably when the vehicle is moving (EMEA markets only). ? VR messages in Spanish talks to fast. ? Recognition enhancement for Russian VR. ? Hands free audio too low for non-amp vehicle (KL). ? Intermittently ?Registration expired? pop-up appears on display screen. ? Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). ? Incorrect time to destination, when
08-036-14 REV. A
RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. A customer may experience, one or more of the following conditions. Navigation function may resets itself after using One-Shot Voice Recognition (VR). Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers. (U.S. market only) Able to adjust audio balance / fade settings during a VR session. Correct, condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on. Enhancement to navigation routing. Radio display may shows ?Please insert USB Stick?. Enhancement made when video is display in radio when using PAL format video disks. Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to reverse. Enhancements for iPod or iPhone devices that may not start playing after connecting. iPod would not resume playing after a VR session or phone call. Radio reset, screen lockup, blank screen or sluggish system response time. Compass indicator turns off. Touch screen shut down message. Radio surround sound will not stay ON. Driver memory feature causes Sirius XM failure. Loss of radio presets. Battery drain - due to radio remains on. Uconnect apps don't load. AM/FM popping noises and/or static. Backup camera display is blank
08-062-14
Replace Radio No AM Or FM Reception This bulletin involves replacing the RJ radio with a RA sales code radio. No FM or AM reception.
18-034-14 REV. A
P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
21-018-14 REV. A
Flash: Transmission Shift and Diagnostic Enhancements This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software. NOTE: Vehicles that are being updated from TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number) will not require the transmission Adaptation Learn Procedure as indicated in Service Bulletin 21-013-13. However, vehicles that are being updated from any other TCM software may require the transmission Adaptation Learn Procedure. Refer to Service Bulletin 21-013-13 for detailed procedures. Failure to perform the procedures outlined in Service Bulletin 21-013-13 on vehicles that were updated from any other TCM software besides p/n 682235$$AN or 682354$$AN may result in undesirable shift quality. Diagnostic Trouble Code (DTC) robustness improvements are included in this software release. These improvements apply to the following DTC?s: ? P072F- Stuck in Gear 4 ? P076F- Gear 7 shift incorrect ratio ? P0810- Clutch position control error ? P1CC9- Unable to engage gear ? P0734- Gear 4 shift incorrect ratio ? P061B- Internal control module torque calculation performance NOTE: Diagnostic Trouble Code (DTC) robustness improvements were included in TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number). Standard diagnostic trouble shooting procedures should be followed for any vehicle equipped with TCM software p/n 682235$$AN or 682354$$AN exhibiting any of the previous codes. Transmission shift improvements are included in this software release. These improvements apply to the following: ? Garage shifts (Park to Reverse or Drive). ? Coastdown shift quality. ? Shift quality. ? Throttle response and performance feel. ? Management and prevention of busy shifting. ? Lift foot/change mind shift quality.
08-054-14
Flash: RM4 UCONNECT AM/FM/BT/NAV/Voice Navigating Resets When Driving This bulletin involves update the radio with new software. Customer may experience the navigation resets while driving.
21-020-14
Flash: Improved Transmission 5-3 Coast Down Shift Quality This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software.Vehicles that are being updated from TCM software p/n 682411$$AA, 682235$$AN or 682354$$AN ($$ are wild cards for any number) will not require the transmission Adaptation Learn Procedure as indicated in Service Bulletin 21-013-13. However, vehicles that are being updated from any other TCM software may require the transmission Adaptation Learn Procedure. Refer to Service Bulletin 21-013-13 for detailed procedures. Failure to perform the procedures outlined in Service Bulletin 21-013-13 on vehicles that were updated from any other TCM software besides p/n 682411$$AA, 682235$$AN or 682354$$AN may result in undesirable shift quality. Customers may indicate that they experience poor shift quality during a 5-3 coast down.
18-034-14
P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
SB-18-034-14
ON SOME MODEL VEHICLES AND JEEPS, (MY 2013-2014)MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATES AND DIAGNOSTIC TROUBLE CODE (DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE
08-050-14
Flash: Instrument Panel Cluster Translation Update For Japan And South Korea This bulletin involves flashing the instrument cluster to repair incorrect characters appearing in the cluster display. The customer may experience Korean characters in the instrument cluster for a few seconds when the door is opened and when the engine is turned off. The wrong characters only appear for a few seconds then the cluster displays the correct characters.
0805014
Flash: Instrument Panel Cluster Translation Update For Japan And South Korea
21-018-14
Flash: Transmission Shift and Diagnostic Enhancements This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software. NOTE: Vehicles that are being updated from TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number) will not require the transmission Adaptation Learn Procedure as indicated in Service Bulletin 21-013-13. However, vehicles that are being updated from any other TCM software may require the transmission Adaptation Learn Procedure. Refer to Service Bulletin 21-013-13 for detailed procedures. Failure to perform the procedures outlined in Service Bulletin 21-013-13 on vehicles that were updated from any other TCM software besides p/n 682235$$AN or 682354$$AN may result in undesirable shift quality. Diagnostic Trouble Code (DTC) robustness improvements are included in this software release. These improvements apply to the following DTC?s: ? P072F- Stuck in Gear 4 ? P076F- Gear 7 shift incorrect ratio ? P0810- Clutch position control error ? P1CC9- Unable to engage gear ? P0734- Gear 4 shift incorrect ratio ? P061B- Internal control module torque calculation performance NOTE: Diagnostic Trouble Code (DTC) robustness improvements were included in TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number). Standard diagnostic trouble shooting procedures should be followed for any vehicle equipped with TCM software p/n 682235$$AN or 682354$$AN exhibiting any of the previous codes. Transmission shift improvements are included in this software release. These improvements apply to the following: ? Garage shifts (Park to Reverse or Drive). ? Coastdown shift quality. ? Shift quality. ? Throttle response and performance feel. ? Management and prevention of busy shifting. ? Lift foot/change mind shift quality.
08-047-14
Flash: Crank No Start When Using Remote Start In Very Cold Temperatures This bulletin involves updating the software in the Body Control Module (BCM). The customer may experience when using the remote start in very cold weather, (-20 F -29 C) the vehicle will crank but will not start. The vehicle will only crank for a short time then stops. The BCM will see that the RPM is to low and will disengage the starter. The updated software will increase the time the BCM looks at the RPM and lower the RPM threshold from 400 to 300 RPM.
0804714
Flash: Crank No Start When Using Remote Start In Very Cold Temperatures
No83
MasterTech Updates
9003081
Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
08-008-14
RA2 RG2 Or RJ2 Radio Update To Prevent Display Screen Lockup This bulletin involves updating the radio's software or replacing the radio if required. A customer may experience the radio display screen is locked on the Ram logo. This software update is to prevent this condition from occurring. Vehicles equipped with satellite radio (sales code RSD) may have a condition were the radio may reset a few times during a drive cycle. This condition is very intermittent.
08-008-14 REV. B
RA2 RG2 Or RJ2 Radio Update To Prevent Display Screen Lockup This bulletin involves updating the radio's software or replacing the radio if required. A customer may experience the radio display screen is locked on the Ram logo. This software update is to prevent this condition from occurring. Vehicles equipped with satellite radio (sales code RSD) may have a condition were the radio may reset a few times during a drive cycle. This condition is very intermittent.
18-031-14
Flash: MIL Illumination P1239- Engine Oil Temperature Too Low. Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: ? P1239 - Engine Oil Temperature Too Low The following system improvements have also been included in this software release: ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy
02-001-14
Cold Temperature Squeak/Creak Noise While Turning The Steering Wheel This bulletin involves applying Nye® lubricant to the front strut mounts. Customer may describe a creak or squeak noise while turning the steering wheel. Noise is typically more noticeable during cold temperatures below 4°C (40°F), noise may go away when temperature warms up.
02-001-14 REV. A
Cold Temperature Squeak/Creak Noise While Turning The Steering Wheel This bulletin involves applying Nye® lubricant to the front strut mounts. Customer may describe a creak or squeak noise while turning the steering wheel. Noise is typically more noticeable during cold temperatures below 4°C (40°F), noise may go away when temperature warms up.
02-001-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-036-14
RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. A customer may experience, one or more of the following conditions. ? Navigation display enhancement. ? Enables Via Mobile software features when released to consumers. ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connecting. ? iPod would not resume playing after a VR session or phone call. ? Radio reset, screen lockup, blank screen or sluggish system response time. ? Compass indicator turns off. ? Touch screen shut down message. ? Radio surround sound will not stay ON. ? Driver memory feature causes Sirius XM failure. ? Loss of radio presets. ? Battery drain - due to radio remains on. ? Uconnect apps don't load. ? AM/FM popping noises and/or static. ? Backup camera display is blank. ? Compass direction may be incorrect. ? Vehicle's Icon changes on the navigation map. ? Loss of vehicle position on NAV map. ? ?Vehicle Phone Requires Service? message appears on 8.4? screen. ? Nav turn-by-turn enhancements. ? Nav map guidance enhancements. ? Nav text overlaps in detour menu. ? Nav map, vehicle location enhancements in areas with low GPS signals. ? Navigation shows vehicle in San
08-033-14
RA2 RJ2 Or RG2 Radio With B2204 ECU Configuration Mismatch - Not Configured After Proxi This bulletin involves updating the radio's software and performing a proxi alignment. The Technician may experience, when trying to add a sales code to the vehicle and then performing a BCM Proxi configuration, a DTC may set, DTC B2204-55 ECU Configuration Mismatch - Not Configured.
18-013-14 REV. A
Flash: MIL Illumination P2251- O2 Sensor 1/1 Negative Current Control Circuit Open and/or P0031- O2 Sensor 1/1 Heater Circuit Low This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTC?s) have been set: P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open P0031 - O2 Sensor 1/1 Heater Circuit Low
18-013-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-021-14 REV. A
RG3 RG4 RJ3 RJ4 RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? Some Russian letters are caps when they should be lower-case. ? Touch screen locks up in navigation, when Russian is selected. ? Address search availably when the vehicle is moving (EMEA markets only). ? VR messages in Spanish talks to fast. ? Recognition enhancement for Russian VR. ? Hands free audio too low for non-amp vehicle (KL). ? Intermittently ?Registration expired? pop-up appears on display screen. ? Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). ? Incorrect time to destination, when ignition is cycled. ? Volume adjustment for navigation prompts, for phone call. ? Incorrect rear to center fade displayed at start up. ? Translation enhancements for French German and Spanish. ? Right arrow doesn't work for advancing through preset. ? Map zoom level reduced. ? Park sense audio tone stuck on. ?
08-026-14
Flash: RK4 RM4 RL4 UCONNECT 8.4N AM/FM/BT/NAV This bulletin provides software to fix the following issues: Simplified Chinese handwriting recognition issue applicable to China CIP radio, (RK4) eCall message related battery drain issue applicable to China/Japan/S.Korea (RK4,RM4,RL4) Simplified Chinese handwriting recognition issue applicable to China CIP radio, (RK4) eCall message related battery drain issue applicable to China/Japan/S.Korea (RK4,RM4,RL4)
18-013-14
Flash: MIL Illumination P2251- O2 Sensor 1/1 Negative Current Control Circuit Open and/or P0031- O2 Sensor 1/1 Heater Circuit Low This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTC?s) have been set: ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open ? P0031 - O2 Sensor 1/1 Heater Circuit Low
08-019-14
Flash: Remote Proximity Keyless Entry May Not Unlock The Manual Liftgate This bulletin involves updating the Radio Frequency HUB (RF HUB) with new software. Customers may experience that the manual liftgate will not unlock automatically with the remote proximity keyless entry system. The liftgate can be unlocked, using the liftgate unlock button on the FOBIK.
21-007-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
23-003-14
Clicking Noise While Operating The Right Front Exterior Door Handle This bulletin involves removing, modifying, and reinstalling the right front exterior door handle. The right front exterior door handle rubs against the beltline reinforcement inside the door resulting in a clicking noise when operating the exterior door handle.
SB-21-014-13
JEEP: TRANSMISSION CONTROL MODULE (TCM), ON SOME JEEPS, WITH NEW SOFTWARE ROBUSTNESS IMPROVEMENTS, EXPERIENCING INCONSISTENT AND/OR HARSH 1-2 OR 2-3 UPSHIFTS. MODEL 2014 CHEROKEE. *PE
08-093-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-049-13REV.G
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-093-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
24-003-13REV.B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-049-13REV.F
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-089-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-002-13REV.C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
24-003-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
D-13-35
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-058-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.