Vehicle report

2018 JEEP CHEROKEE

Compare every JEEP CHEROKEE yearNHTSA and EPA records

Service bulletins

150 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

03-001-26

Service Bulletin/Repair Instructions

Unable to Complete 01C Recall Drive Cycle C14A7-97 Active Technicians may experience the following: SYMPTOM: ● After performing Recall 01C, the vehicle may get a 'Service AWD' message on the EVIC.

03-002-26

Service Bulletin/Repair Instructions

Stop/Start Illuminated, 0x22 During Fork Wear Routine Technicians may experience the following: SYMPTOM: ● Negative response 0X22 after Recall 01C flash triggers one or more communication codes with controllers.

S2208000045 REV.D

Service Bulletin/Repair Instructions

Backup Camera Poor Image Quality Inspection

S2523000003 REV.A

Service Bulletin/Repair Instructions

Door Latch, Handle And Ajar Additional Service Information.

21-027-26 REV. A

Service Bulletin/Repair Instructions

Two Speed Power Transfer Unit Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): ? C1494-07 - PTU Fork Position-Mechanincal Failures. Customers m

111432

Warranty Program/Extension

D-26-10 (XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

111447

Warranty Program/Extension

ID-26-19 (XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

14078

Warranty Program/Extension

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

14079

Warranty Program/Extension

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

14081

Warranty Program/Extension

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

14082

Warranty Program/Extension

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

21-027-26

Service Bulletin/Repair Instructions

S1408000384 REV.J

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

S1408000384 REV.I

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

S1721000016 REV.B

Service Bulletin/Repair Instructions

Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked.

9100736

Service Bulletin/Repair Instructions

Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

31-001-25 REV. B

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

9100645

Service Bulletin/Repair Instructions

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

9100653

Service Bulletin/Repair Instructions

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

31-001-25 REV. A

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

31-001-25

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

S2208000138 REV.B

Service Bulletin/Repair Instructions

Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed

S2323000002 REV.A

Service Bulletin/Repair Instructions

Washer Light On And Will Not Turn Off After Adding Washer Solvent.

9100471

Service Bulletin/Repair Instructions

CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.

S1408000384 REV.H

Service Bulletin/Repair Instructions

S2523000003

Service Bulletin/Repair Instructions

Door Latch, Handle And Ajar Additional Service Information.

S1408000384 REV.G

Service Bulletin/Repair Instructions

9100468

Service Bulletin/Repair Instructions

FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

09-018-24

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

31-001-24

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

S1408000384 REV.F

Service Bulletin/Repair Instructions

97892

Other

SWITCH - BRAKE

S1408000384

Service Bulletin/Repair Instructions

S1721000016

Service Bulletin/Repair Instructions

Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked, Set.

9100229

Service Bulletin/Repair Instructions

LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.

9004542

Service Bulletin/Repair Instructions

Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.

9100226

Service Bulletin/Repair Instructions

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

93023

Service Bulletin/Repair Instructions

Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)

93120

Service Bulletin/Repair Instructions

FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC

9100196

Service Bulletin/Repair Instructions

Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used

ZD7

Service Bulletin/Repair Instructions

Customer Satisfaction Notification ZD7 - Radio Software update

ReferenceZD7

Service Bulletin/Repair Instructions

Customer Satisfaction Notification ZD7 - Radio Software Update

BulletinA

Service Bulletin/Repair Instructions

Customer Satisfaction Notification ZD7 - Radio Software Update

0700723

Service Bulletin/Repair Instructions

Water Quality When Mixed With Engine Coolant

1804823

Service Bulletin/Repair Instructions

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

0900323

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ? Oil pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

9003357A

Service Bulletin/Repair Instructions

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

9003357a

Service Bulletin/Repair Instructions

9003357

Service Bulletin/Repair Instructions

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

3100123

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

09-003-23

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: Oil pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

88806

Service Bulletin/Repair Instructions

Warranty Bulletin D-23-01 - (XB1) 2.4L Engine ? Select 2014 - 2019 Jeep Cherokee (KL), 2017 - 2018 Jeep Compass (MP), 2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

S2323000002

Service Bulletin/Repair Instructions

Washer Light On And Will Not Turn Off After Adding Washer Solvent.

31-002-22

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

09-013-22

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

3100122

Service Bulletin/Repair Instructions

Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

S2208000138

Service Bulletin/Repair Instructions

Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed

S1523000016

Service Bulletin/Repair Instructions

A Rattle Or Creak Noise Is Heard From The Dual Pane Sunroof Area.

0807622

Service Bulletin/Repair Instructions

UAS, UAQ, UCS, UAV, UCV and UCQ Radio Over The Air Software Version Updates

S2209000004

Service Bulletin/Repair Instructions

If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.

S2208000073

Service Bulletin/Repair Instructions

No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting

S1708000118

Service Bulletin/Repair Instructions

Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off

S1708000118 RevB

Service Bulletin/Repair Instructions

Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off

1804622

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC):P06EF - Engine Restart Performance. Customers may experience the following:Long engine crank after an Engine Stop/Start (ESS) event.

CSNW20

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

W20

Service Bulletin/Repair Instructions

Powertrain Control Module.

9004401

Service Bulletin/Repair Instructions

DIFFERENTIAL, Rear Axle (KL 4WD w/DK2 = 1-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM · 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · 68550586A$ service RDMs have a 20 clutch plate design · Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA · If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540645AA for the 24 plate RDM with a new pump. · Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M

9004402

Service Bulletin/Repair Instructions

DIFFERENTIAL, Rear Axle (KL 4WD w/DK4 = 2-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM · 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design · Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. · If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540646AA for the 24-plate RDM with a new pump. · Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti

S2108000198

Service Bulletin/Repair Instructions

Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit

0500421

Service Bulletin/Repair Instructions

Front Click Noise at Low Speed Turns

S2108000163

Service Bulletin/Repair Instructions

No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration

S2109000004

Service Bulletin/Repair Instructions

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

2300521

Service Bulletin/Repair Instructions

Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

2300521REVB

Service Bulletin/Repair Instructions

S1809000007

Service Bulletin/Repair Instructions

Customer Complaint May Include Engine Oil Leak Or Consumption

S1809000007RevC

Service Bulletin/Repair Instructions

Customer Complaint May Include Engine Oil Leak Or Consumption

9004386

Service Bulletin/Repair Instructions

WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

23-005-21 Rev. A

Service Bulletin/Repair Instructions

S1809000007 Rev.

Service Bulletin/Repair Instructions

Customer Complaint May Include Engine Oil Leak Or Consumption

S1908000107

Service Bulletin/Repair Instructions

Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated

S1908000107 Rev.

Service Bulletin/Repair Instructions

Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated

W20 Combo Phase4

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

S1608000226

Service Bulletin/Repair Instructions

Battery Tester Warranty Code Procedures, Midtronics Charger Update Process

S2008000113

Service Bulletin/Repair Instructions

No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message

S2008000113 Rev.

Service Bulletin/Repair Instructions

No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message

S16080002261

Service Bulletin/Repair Instructions

Battery Tester Warranty Code Procedures, Medtronic Update Process

S1821000001

Service Bulletin/Repair Instructions

Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders

9004009

Service Bulletin/Repair Instructions

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

W20 Combo Phase3

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module (Revision 2)

W20 Combo Phase2

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

23-005-21

Service Bulletin/Repair Instructions

Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replacedas well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle willneed to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

W20 Combo

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

S1908000028 Rev.

Service Bulletin/Repair Instructions

(Rev. A) Power Inverter Load Ratings

S1908000102

Service Bulletin/Repair Instructions

(Rev. A) Power Inverter Load Ratings

31-002-20

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

3100220

Service Bulletin/Repair Instructions

9003637

Service Bulletin/Repair Instructions

USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

S2021000004

Service Bulletin/Repair Instructions

Valve Body Learn Procedure On WiTech Shows The Transmission Is Not In The Proper Gear After Repairs

S2008000010

Service Bulletin/Repair Instructions

Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns

09-006-20 REV. B

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

0900620

Service Bulletin/Repair Instructions

9003968

Service Bulletin/Repair Instructions

CONDENSER, Air Conditioning CONDITION 1: If it is determined that the A/C compressor does not engage due to a refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

S2008000093

Service Bulletin/Repair Instructions

Blind Spot Or Park Assist Warnings, False Activation

09-006-20 REV. A

Service Bulletin/Repair Instructions

09-006-20

Service Bulletin/Repair Instructions

23-015-20

Service Bulletin/Repair Instructions

Disinfectant Solution Recommended for COVID-19

S2008000058

Service Bulletin/Repair Instructions

Rear Power Liftgate Does Not Unlock

08-049-20

Service Bulletin/Repair Instructions

Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

9004244

Service Bulletin/Repair Instructions

COOLER, Transmission Oil Work procedure to address fluid leak issue with the transmission oil cooler on the MP (Part # 68249191A$), KL (Part # 68399021A$) and RU (Part # 68217322A$) needs to be followed. Service Instructions for the Condition of a TOC fluid leak: 1) Mark the leakage area if visible to assist in diagnosis and determination of the area where the leak has occurred. 2) If fluid leak was caused by damage or leakage at the transmission oil cooler: - Replace transmission oil cooler - Test drive and verify no additional fluid leaks 3) If fluid leak was caused by leak at quick connect fittings: - Replace transmission oil cooler lines - Test drive and verify no additional fluid leaks

18-039-20

Service Bulletin/Repair Instructions

Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season

S2019000002

Service Bulletin/Repair Instructions

Hands On Steering Wheel Message In EVIC

S1823000053

Service Bulletin/Repair Instructions

Water Leak On Floor Near A Pillar

S2023000022

Service Bulletin/Repair Instructions

Window Slow To Raise Or Lower May Be Noisy

S2018000003

Service Bulletin/Repair Instructions

Customer complaint may include MIL/Check Engine lamp on. Upon further inspection, fault code P219A - Bank 1 Air-Fuel Ratio Imbalance may be found in the powertrain control module (PCM) as pending, active, or stored. Other fault codes P1066, P1068, P106A, or P106C (Solenoid Valve Switch Off Time Out of Range) may also be stored. Customer may also complain about loss of power or engine running rough while P219A is active.

9004247

Service Bulletin/Repair Instructions

Glass Run Window Seal For an issue of glass squeaking or making noise when rolling up/down. Verify that glass run seal is clear and clean of any dirt or debris, and make sure glass is in window track/window glass run seal, then roll window up and down fully 3 times to verify the issue repeats. Clean window track, window, and glass run seal if dirt or debris is found. If window is not in window track or inside glass run seal, repair condition using original glass run seal if no deformities are found in the seal. If glass run seal is deformed, replace glass run seal and ensure seal is fully installed in door channel prior to glass reinstallation. If lubricant is needed during repair, use Mopar part # 04773427A$ or 05019059A$ (approved Krytox lubricant for weatherstrips). For additional information contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

S1808000175

Service Bulletin/Repair Instructions

LED Front Fog Lamps Flicker Or Intermittently Light, Are Dim Or Inoperative. A U11E9, or B16FB-15 may be set

S1808000072

Service Bulletin/Repair Instructions

No Start, Keyless Button Only Goes To Accessory, 3rd Brake Lamp And Left Rear Tail Lamp Dim

21-018-20

Service Bulletin/Repair Instructions

Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customer may experience a undesirable or long 5-4 shift during a vehicle coast-down.

08-027-20

Service Bulletin/Repair Instructions

2.4L Ignition Coil Boot Replacement This bulletin involves replacing all four ignition coil insulating boots. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

S2023000013

Service Bulletin/Repair Instructions

Water Leak In Area Of A Pillar Or On Passenger Floor

S2008000013

Service Bulletin/Repair Instructions

Key Programming, Security Pin Request, Pin Invalid

S1805000006

Service Bulletin/Repair Instructions

ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

9004214

Service Bulletin/Repair Instructions

ENGINE, Long Block For 2017 and 2018 model year vehicles at U.S. dealers only Engineering is seeking information regarding engine operation. Before replacing a Tigershark equipped 2017/2018 KL or MP. Please call FCA Redacted Content . Have VIN last 8 and engine serial number available (located on sticker on valve cover - example TZEP1171811106.) If no response in 15 minutes, proceed with repair.

9004022

Service Bulletin/Repair Instructions

Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

08-111-19 REV. A

Service Bulletin/Repair Instructions

RA3 and RA4 GPS Calibration Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)

VB3

Service Bulletin/Repair Instructions

Revised Customer Satisfaction Notification VB3 ? Navigation Flash

VB3 REV1

Service Bulletin/Repair Instructions

Revised Customer Satisfaction Notification VB3 ? Navigation Flash

31-004-19

Service Bulletin/Repair Instructions

Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.

31-005-19

Service Bulletin/Repair Instructions

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.

3100319

Service Bulletin/Repair Instructions

Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.

3100419

Service Bulletin/Repair Instructions

3100519

Service Bulletin/Repair Instructions

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.

3100619

Service Bulletin/Repair Instructions

Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.

D-19-25

Service Bulletin/Repair Instructions

RRT 19-090 (Service Bulletin 08-111-19) 2013-2018 Multiple Vehicles RA3/RA4 Radio GPS Certification Error

D1925

Service Bulletin/Repair Instructions

RRT 19-090 (Service Bulletin 08-111-19) 2013-2018 Multiple Vehicles RA3/RA4 Radio GPS Certification Error

9003825

Service Bulletin/Repair Instructions

LATCH, Hood For the following concerns, please verify secondary plunger switch before replacing hood latch with primary switch. Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch.

08-111-19

Service Bulletin/Repair Instructions

RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)

0811119

Service Bulletin/Repair Instructions

RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)

18-089-19

Service Bulletin/Repair Instructions

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

1808919

Service Bulletin/Repair Instructions

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

9003220

Service Bulletin/Repair Instructions

RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

9003293

Service Bulletin/Repair Instructions

A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

D-17-21

Service Bulletin/Repair Instructions

Radio Pre-Authorization Program - Select 7.0/8.4/8.4N Radios (New and Exchange) - 2018 Model Year Vehicles

2104617

Service Bulletin/Repair Instructions

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) withthe latest available software. Customers may experience the following:Longer than usual shift times when performing garage shifts (P to R and Rto D). Poor shift quality or ?bump? experienced during foot on throttle2-1 downshift.

9003783

Service Bulletin/Repair Instructions

Shifter - Automatic Transmission If a 2015 - 18MY KL ONLY is brought in with a ?Service Shifter? message on the cluster and/or the following DTCs are present indicating loss of communication with the shifter: U0103, U0103-87. Prior to beginning any repair, please call John Zbranchik at 248-576-0756 or Pablo Flores at 248-576-3972. If no reply contact Dil Weerasinha at 248-944-5967 or Jay Nagle 248-576-5657. If you are unable to contact any of the above, and all the DTCs related to loss of comm are STORED, first perform a vehicle scan with a wiTECH tool or similar and email the log to john.zbranchik@fcagroup.com and pablo.flores1@fcagroup.com. Ensure all stored DTCs in the vehicle are recorded in the log. Use the tool to clear all codes and ensure the ?Service Shifter? message does not return. If this is the first occurrence of this issue on this vehicle, do NOT replace the shifter at this time. If any DTCs related to loss of comm with the shifter are ACTIVE, a full bus log is highly desired. Please contact a regional tech representative to acquire this log. After the log is acquired, or if this is not feasible, check for loose/bent pins, spread terminals on both the male pin cavity in the shifter and the female connector from the body harness take out and all grounds. If no issues are found, replace the shifter and return it to the Quality Engineering Center (QEC).

9003789

Service Bulletin/Repair Instructions

KL Gear Shift Module For 2015-2018 KL ONLY, if vehicle DTC Code P1C86-1D (PRNDL Display Current out of Range) is verified as either stored or active please contact Pablo Flores in FCA Chassis Engineering at cell (248) 979-7062. If no response in 15 minutes, proceed with repair. For additional repair see NOTES below: NOTE 1: If DTC P1C86-1D is still active after inspecting harness connections from Service Procedure (STEP 2). DO NOT replace SHIFTER ASSEMBLY. Instead, replace PRNDM bezel only. NOTE 2: After replacing PRNDL Assembly, clear DTCs and check to confirm DTC does not return. Please return parts back to FCA Engineering if PRNDM is deemed non-functional after performing this Tech Tip. For 2015-2018 KL ONLY; If vehicle DTC Code P1C86-1D (PRNDL Display Current out of Range) is verified as either stored or active please contact Pablo Flores in FCA Chassis Engineering at cell (248) 979- 7062. If no response in 15 minutes, proceed with repair. For additional repair see NOTES below: NOTE 1: If DTC P1C86-1D is still active after inspecting harness connections from Service Procedure (STEP 2). DO NOT replace SHIFTER ASSEMBLY. Instead, replace PRNDM bezel only. NOTE 2: After replacing PRNDL Assembly, clear DTCs and check to confirm DTC does not return. Please return parts back.

9003109

Service Bulletin/Repair Instructions

Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

9003696

Service Bulletin/Repair Instructions

Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

05152029

Service Bulletin/Repair Instructions

Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

9002519

Service Bulletin/Repair Instructions

82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.