Vehicle report

2019 JEEP CHEROKEE

Service bulletins

286 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

03-001-26

Service Bulletin/Repair Instructions

Unable to Complete 01C Recall Drive Cycle C14A7-97 Active Technicians may experience the following: SYMPTOM: ● After performing Recall 01C, the vehicle may get a 'Service AWD' message on the EVIC.

03-002-26

Service Bulletin/Repair Instructions

Stop/Start Illuminated, 0x22 During Fork Wear Routine Technicians may experience the following: SYMPTOM: ● Negative response 0X22 after Recall 01C flash triggers one or more communication codes with controllers.

S2208000045 REV.D

Service Bulletin/Repair Instructions

Backup Camera Poor Image Quality Inspection

S2523000003 REV.A

Service Bulletin/Repair Instructions

Door Latch, Handle And Ajar Additional Service Information.

08-075-26 REV. A

Service Bulletin/Repair Instructions

Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

21-027-26 REV. A

Service Bulletin/Repair Instructions

Two Speed Power Transfer Unit Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): ? C1494-07 - PTU Fork Position-Mechanincal Failures. Customers m

111432

Warranty Program/Extension

D-26-10 (XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

111447

Warranty Program/Extension

ID-26-19 (XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

14078

Warranty Program/Extension

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

14079

Warranty Program/Extension

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

14081

Warranty Program/Extension

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

14082

Warranty Program/Extension

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

21-027-26

Service Bulletin/Repair Instructions

Two Speed Power Transfer Unit Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): ? C1494-07 - PTU Fork Position-Mechanincal Failures. Customers m

18-044-26

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi

S2208000045 REV.C

Service Bulletin/Repair Instructions

Backup Camera Poor Image Quality Inspection

S1408000384 REV.J

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

08-075-26

Service Bulletin/Repair Instructions

Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

S1408000384 REV.I

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

S1721000016 REV.B

Service Bulletin/Repair Instructions

Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked.

9100736

Service Bulletin/Repair Instructions

Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

S1805000006 REV.B

Service Bulletin/Repair Instructions

ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

9100325 Rev 1

Service Bulletin/Repair Instructions

Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.

23-008-25 REV. A

Service Bulletin/Repair Instructions

Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

02-002-25 REV. A

Service Bulletin/Repair Instructions

Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.

31-001-25 REV. B

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

9100645

Service Bulletin/Repair Instructions

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

9100653

Service Bulletin/Repair Instructions

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

31-001-25 REV. A

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

31-001-25

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

08-220-25

Service Bulletin/Repair Instructions

Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

S2208000138 REV.B

Service Bulletin/Repair Instructions

Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed

S2323000002 REV.A

Service Bulletin/Repair Instructions

Washer Light On And Will Not Turn Off After Adding Washer Solvent.

9100471

Service Bulletin/Repair Instructions

CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.

23-008-25

Service Bulletin/Repair Instructions

Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.

102934

Service Bulletin/Repair Instructions

THROTTLE BODY

S1408000384 REV.H

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

S2523000003

Service Bulletin/Repair Instructions

Door Latch, Handle And Ajar Additional Service Information.

S1408000384 REV.G

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

9100468

Service Bulletin/Repair Instructions

FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

9100445

Service Bulletin/Repair Instructions

Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369691AD) is the proper repair.

S2208000045 REV.B

Service Bulletin/Repair Instructions

Backup Camera Poor Image Quality Inspection

S228A000017 REV.A

Service Bulletin/Repair Instructions

Battery Drain Suspected or "Identified" From USB or Media Hub

09-018-24

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

23-004-24 REV. A

Service Bulletin/Repair Instructions

Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.

31-001-24

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

08-153-24

Service Bulletin/Repair Instructions

Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

S1408000384 REV.F

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

97892

Other

SWITCH - BRAKE

2300424

Service Bulletin/Repair Instructions

Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.

S248A000001

Service Bulletin/Repair Instructions

SOS and Assistance Call Not Working After Radio Exchange Unit Installed

S1408000384

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

S1721000016

Service Bulletin/Repair Instructions

Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked, Set.

9100229

Service Bulletin/Repair Instructions

LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.

9004542

Service Bulletin/Repair Instructions

Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.

9100226

Service Bulletin/Repair Instructions

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

93023

Service Bulletin/Repair Instructions

Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)

93120

Service Bulletin/Repair Instructions

FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC

S2108000093

Service Bulletin/Repair Instructions

Apple CarPlay Does Not Work Or Not Connecting

9100196

Service Bulletin/Repair Instructions

Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used

ZD7

Service Bulletin/Repair Instructions

Customer Satisfaction Notification ZD7 - Radio Software update

ReferenceZD7

Service Bulletin/Repair Instructions

Customer Satisfaction Notification ZD7 - Radio Software Update

BulletinA

Service Bulletin/Repair Instructions

Customer Satisfaction Notification ZD7 - Radio Software Update

1806523

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software.

0700723

Service Bulletin/Repair Instructions

Water Quality When Mixed With Engine Coolant

S238A000024

Service Bulletin/Repair Instructions

SOS, Assistance Calls Not Successful After Radio Replacement or Radio Software Update

0811223

Service Bulletin/Repair Instructions

Rear Tail Lamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). This bulletin is to communicate the procedure for rear tail lamp condensation clearing.

9100142

Service Bulletin/Repair Instructions

Mirror

1804823

Service Bulletin/Repair Instructions

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

0900323

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ? Oil pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

9003357A

Service Bulletin/Repair Instructions

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

9003357a

Service Bulletin/Repair Instructions

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

S228A000028

Service Bulletin/Repair Instructions

Radio Remained On After Ignition Is Switched Off, Dead Battery From Excessive Radio Current Draw

9003357

Service Bulletin/Repair Instructions

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

3100123

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

08-038-23

Service Bulletin/Repair Instructions

Radio Over The Air JR34.3 Updating to JR34.32.Software Version Customers may experience one or more of the following: Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.

S2308000009

Service Bulletin/Repair Instructions

Electric Power Steering (EPS) Will Not Calibrate, Negative Response Error Code 0X10

09-003-23

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: Oil pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

88806

Service Bulletin/Repair Instructions

Warranty Bulletin D-23-01 - (XB1) 2.4L Engine ? Select 2014 - 2019 Jeep Cherokee (KL), 2017 - 2018 Jeep Compass (MP), 2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

S2323000002

Service Bulletin/Repair Instructions

Washer Light On And Will Not Turn Off After Adding Washer Solvent.

S2218000023

Service Bulletin/Repair Instructions

Malfunction Indicator Lamp (MIL) Illuminated. Diagnostic Trouble Code (DTC) U02A3 ? Lost Communication ith Particulate Matter (PM) Sensor, Set After PM Sensor Replacement.

08-003-22 REV. A

Service Bulletin/Repair Instructions

UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

31-002-22

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

08-229-22

Service Bulletin/Repair Instructions

Radio Over The Air Software Version Update to 22.66 This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from IR22.64 and IR22.65 to IR22.66. The national launch for the FOTA is expected to begin on January 09, 2023. ? Wi-Fi hotspot connection not working. ? No internet connection message on the phone when trying to connect to a device

09-013-22

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

S2008000131 Rev.

Service Bulletin/Repair Instructions

U11E9 Lost Communication with AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated

18-161-22

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. P2C90 - Crankcase Ventilation System - Hose "A" Disconnected. P1D73 - AGS performance fault. P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(Enlarged Europe and Middle East/Africa) only equipped with Gas ParticulateFilter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included: AGS stuck condition (The customer won't see an issue, but this calibrationallows AGS performance fault - P1D73, to work correctly). Software corrects an issue with the wrong cylinder identification if an injectorcircuit performance fault is set in the PCM: If any of the series of injector control circuit faults are set, please refer tothe bullet-pointed list below to determine which injector to address.

0821422

Service Bulletin/Repair Instructions

Radio Over The Air Updates to JR34.3/JR34.4 and JR34.41

S1823000031

Service Bulletin/Repair Instructions

Flat Tow Or Recreational Towing KL Cherokee

3100122

Service Bulletin/Repair Instructions

Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

S228A000017

Service Bulletin/Repair Instructions

Battery Drain Suspected or "Identified" From USB or Media Hub

S2208000138

Service Bulletin/Repair Instructions

Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed

S228A000004RevB

Service Bulletin/Repair Instructions

Panasonic VP4R Wi-Fi New Enrollment Pause

2302422

Service Bulletin/Repair Instructions

Headlamp Condensation Clearing Procedure This bulletin is to communicate the procedure for headlamp condensation clearing.

S228A000004RevA

Service Bulletin/Repair Instructions

Panasonic VP4R Wi-Fi New Enrollment Pause

S1523000016

Service Bulletin/Repair Instructions

A Rattle Or Creak Noise Is Heard From The Dual Pane Sunroof Area.

S228A000004

Service Bulletin/Repair Instructions

Panasonic VP4R Wi-Fi New Enrollment Pause

08-037-22

Service Bulletin/Repair Instructions

Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate the procedure for rear tail lamp condensation clearing. Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operatingtemperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e., a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into avapor. Turning the tail lamps on will usually accelerate this process.Clear Tail Lamp AssemblyTail Lamp Assembly with CondensationImages are not specific to vehicle, and only used for showing the tail lamps either clearFig. 1or having a condensation build up within the tail lamp assemblyFig. 2per the procedure.

0807622

Service Bulletin/Repair Instructions

UAS, UAQ, UCS, UAV, UCV and UCQ Radio Over The Air Software Version Updates

1807722

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: P1D83 - Implausible Engine Oil Temperature Signal Received. P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit P0616 - Starter Control Circuit Lo. - Starter Control Circuit High. P0607 - ECU Internal Performance

S2209000004

Service Bulletin/Repair Instructions

If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.

S2208000073

Service Bulletin/Repair Instructions

No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting

S1708000118

Service Bulletin/Repair Instructions

Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off

S1708000118 RevB

Service Bulletin/Repair Instructions

Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off

S2208000068

Service Bulletin/Repair Instructions

?Device Not Supported? Message on the radio screen

0800322

Service Bulletin/Repair Instructions

UAQ and UCQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth® pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

CSNW20

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

S2208000028

Service Bulletin/Repair Instructions

Connected Services Will Not Work After Radio Replacement

W20

Service Bulletin/Repair Instructions

Powertrain Control Module.

S2108000204

Service Bulletin/Repair Instructions

Radio Lockup In The Software Installation Screen After Accepting FOTA Update (Incorrect "S2008000204" indicated on published document)

9004401

Service Bulletin/Repair Instructions

DIFFERENTIAL, Rear Axle (KL 4WD w/DK2 = 1-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM · 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · 68550586A$ service RDMs have a 20 clutch plate design · Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA · If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540645AA for the 24 plate RDM with a new pump. · Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M

9004402

Service Bulletin/Repair Instructions

DIFFERENTIAL, Rear Axle (KL 4WD w/DK4 = 2-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM · 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design · Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. · If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540646AA for the 24-plate RDM with a new pump. · Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti

S2008000131RevC

Service Bulletin/Repair Instructions

U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated

S2108000062

Service Bulletin/Repair Instructions

U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated

S2108000198

Service Bulletin/Repair Instructions

Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit

0500421

Service Bulletin/Repair Instructions

Front Click Noise at Low Speed Turns

S2108000170

Service Bulletin/Repair Instructions

Head unit button stuck DTC code B14DA-2A

S2108000163

Service Bulletin/Repair Instructions

No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration

S2109000004

Service Bulletin/Repair Instructions

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

0809921

Service Bulletin/Repair Instructions

UAQ and UCQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth® pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

2300521

Service Bulletin/Repair Instructions

Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

2300521REVB

Service Bulletin/Repair Instructions

Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

S1809000007

Service Bulletin/Repair Instructions

Customer Complaint May Include Engine Oil Leak Or Consumption

S1809000007RevC

Service Bulletin/Repair Instructions

Customer Complaint May Include Engine Oil Leak Or Consumption

S2008000059RevB

Service Bulletin/Repair Instructions

Error Code 20 Message On the Radio Screen

9004386

Service Bulletin/Repair Instructions

WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

S2008000059RevA

Service Bulletin/Repair Instructions

Error Code 20 Message On the Radio Screen

S2108000098RevB

Service Bulletin/Repair Instructions

Radio Screen Freeze, Blank Screen And Reset

S2108000127 Rev.

Service Bulletin/Repair Instructions

Radio Reboot Continually

S2108000127-1

Service Bulletin/Repair Instructions

Radio Reboot Continually

S2108000127REVA

Service Bulletin/Repair Instructions

Radio Reboot Continually

S2108000127RevA

Service Bulletin/Repair Instructions

Radio Reboot Continually

S2108000130

Service Bulletin/Repair Instructions

Bubbles Or Delamination On The Radio Display

S2108000119

Service Bulletin/Repair Instructions

Apple CarPlay Malfunctioning, Does Not Launch Or Is Cutting In An Out On Wired And Wireless Connection, Radio Stuck When IPhone Is Connected

S2108000127

Service Bulletin/Repair Instructions

Radio Reboot Continually

08-093-21

Service Bulletin/Repair Instructions

UAS, UAQ, UCS, UAV, UCV and UCQ Radio Over The Air Software Version Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay® connectivity improvement. Improvement to Bluetooth® phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.

0809321

Service Bulletin/Repair Instructions

UAS, UAQ, UCS, UAV, UCV and UCQ Radio Over The Air Software Version Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay® connectivity improvement. Improvement to Bluetooth® phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.

23-005-21 Rev. A

Service Bulletin/Repair Instructions

Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

S2008000010

Service Bulletin/Repair Instructions

Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns

S2008000010 Rev.

Service Bulletin/Repair Instructions

Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns

S2108000120

Service Bulletin/Repair Instructions

Radio Volume Uncontrollable Or Changing On Its Own

OD21T001

Service Bulletin/Repair Instructions

Safety Recall Communication ? Continental Tire the Americas, LLC (?CTA?) Campaign #21T-001

S2108000098

Service Bulletin/Repair Instructions

Radio Screen Freeze, Blank Screen And Reset

S2108000098 Rev.

Service Bulletin/Repair Instructions

Radio Screen Freeze, Blank Screen And Reset

S1809000007 Rev.

Service Bulletin/Repair Instructions

Customer Complaint May Include Engine Oil Leak Or Consumption

08-070-21

Service Bulletin/Repair Instructions

ULQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 34.2. If the software update is performed on a radio with software below 19.9, the radio could be damaged and will need to be replaced. Customers may experience one or more of the following:Lost radio presets. Radio display screen is black when the ignition is on. Radio may reset, turn itself off and then back on again. Park assist chime will continue to chime after the vehicle is turn off. Radio will display the incorrect speed limit in kph when approaching a road speed camera. In addition the following enhancements are included:Voice Recognition (VR) and Bluetooth® improvements. Improvements for Off-road pages.

0807021

Service Bulletin/Repair Instructions

ULQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 34.2. If the software update is performed on a radio with software below 19.9, the radio could be damaged and will need to be replaced. Customers may experience one or more of the following:Lost radio presets. Radio display screen is black when the ignition is on. Radio may reset, turn itself off and then back on again. Park assist chime will continue to chime after the vehicle is turn off. Radio will display the incorrect speed limit in kph when approaching a road speed camera. In addition the following enhancements are included:Voice Recognition (VR) and Bluetooth® improvements. Improvements for Off-road pages.

S1708000118 Rev.

Service Bulletin/Repair Instructions

Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination After Key Off

S1908000107

Service Bulletin/Repair Instructions

Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated

S1908000107 Rev.

Service Bulletin/Repair Instructions

Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated

W20 Combo Phase4

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

S1608000226

Service Bulletin/Repair Instructions

Battery Tester Warranty Code Procedures, Midtronics Charger Update Process

S2008000113

Service Bulletin/Repair Instructions

No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message

S2008000113 Rev.

Service Bulletin/Repair Instructions

No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message

08-060-21

Service Bulletin/Repair Instructions

Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate that a new procedure for rear tail lamp condensation clearing that is now available in the service information.

0806021

Service Bulletin/Repair Instructions

Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate that a new procedure for rear tail lamp condensation clearing that is now available in the service information.

S16080002261

Service Bulletin/Repair Instructions

Battery Tester Warranty Code Procedures, Medtronic Update Process

S1821000001

Service Bulletin/Repair Instructions

Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders

9004009

Service Bulletin/Repair Instructions

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

S2108000080

Service Bulletin/Repair Instructions

Radio Replacement Reset Routine, Radio Has Missing Icons Or Are Grayed Out

S2108000075

Service Bulletin/Repair Instructions

Transfer Case Terrain Selector Switch LED Inoperative

S2124000004

Service Bulletin/Repair Instructions

A/C does not cool and vehicle is low on Freon charge but no leak is found with sniffer or black light anywhere in the system

08-033-21

Service Bulletin/Repair Instructions

UGQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. The radio may need up tothree USB flash drivesto get the software level to 39.5 Customers may experience one or more of the following:No option to enable or disable the heated seat or steering wheel. Destination information will not clear. Voice Recognition (VR) stays in French while the language is set to English. Radio may reset after Bluetooth® phone receives two text messages one after another. False message displayed ?turn vehicle to run? or ? key on to access menu? when the ignition is already in the run position. Jeep off road page is missing. Latitude and Longitude values on the Jeep off road page is missing. Russian language missing. In addition, the following enhancement are included in this update:Add auto park brake functionality to the control setting in the radio.

0803321

Service Bulletin/Repair Instructions

UGQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. The radio may need up tothree USB flash drivesto get the software level to 39.5 Customers may experience one or more of the following:No option to enable or disable the heated seat or steering wheel. Destination information will not clear. Voice Recognition (VR) stays in French while the language is set to English. Radio may reset after Bluetooth® phone receives two text messages one after another. False message displayed ?turn vehicle to run? or ? key on to access menu? when the ignition is already in the run position. Jeep off road page is missing. Latitude and Longitude values on the Jeep off road page is missing. Russian language missing. In addition, the following enhancement are included in this update:Add auto park brake functionality to the control setting in the radio.

S2108000048

Service Bulletin/Repair Instructions

CEL Lamp On, Drained Battery No Start, DTC B25A9-00 Front Door Handle Sense

18-020-21

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High.P0607 - ECU Internal Performance.

1802021

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High.P0607 - ECU Internal Performance.

S2108000045

Service Bulletin/Repair Instructions

Favorite Song On-Air Alert List Empty

S1808000233 Rev.

Service Bulletin/Repair Instructions

The Passive Entry Door Handle Does Not Unlock The Door And B25A3-00 Or B25A4-00 May Be Active

S1808000233RevA

Service Bulletin/Repair Instructions

The Passive Entry Door Handle Does Not Unlock The Door And B25A3-00 Or B25A4-00 May Be Active

W20 Combo Phase3

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module (Revision 2)

08-016-21

Service Bulletin/Repair Instructions

Radio and Back-up Camera Enhancements This bulletin involves updating the radio software level to 1848.34. Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Ghost Touch, features, modes and App?s changing without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first start the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Audio distortion (KL vehicles). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay® or Android Auto Google® maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. Personal Identification Number (PIN) clears and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. Intermittently requires an anti-theft code to be entered. Software update also includes software enhancement.SXM sound and behavior improvements.

W20 Combo Phase2

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

23-005-21

Service Bulletin/Repair Instructions

Front Seat Side Shield Updated Service Procedure This bulletin informs the technician that when either of the front seat side shields are replaced the buckle will need to be replacedas well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle willneed to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

W20 Combo

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

9004335

Service Bulletin/Repair Instructions

Turbocharger If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed o-ring for a leak. The o-ring is serviced separately and complete turbo replacement may not be necessary.

18-063-20 REV. B

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition: Engine Start/Stop inoperative. Remote start inoperative (South Korea vehicles only). Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator

1806320

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition:Engine Start/Stop inoperative. Remote start inoperative(South Korea vehicles only). Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator

S1908000194

Service Bulletin/Repair Instructions

(Rev. A) Hands Free Liftgate Takes Multiple Foot Kicks to Open After The Vehicle Enters A Full Bus Sleep Cycle

S1908000194 Rev.

Service Bulletin/Repair Instructions

(Rev. A) Hands Free Liftgate Takes Multiple Foot Kicks to Open After The Vehicle Enters A Full Bus Sleep Cycle

18-001-20 REV. B

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20201001 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20201001, for details on this service action.

1800120

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20201001 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20201001, for details on this service action.

S2008000172

Service Bulletin/Repair Instructions

Radio Screen Flickering When Using Apple CarPlay Or Android Auto.

S2018000012

Service Bulletin/Repair Instructions

Check engine lamp on. Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.

S1908000028 Rev.

Service Bulletin/Repair Instructions

(Rev. A) Power Inverter Load Ratings

S1908000102

Service Bulletin/Repair Instructions

(Rev. A) Power Inverter Load Ratings

31-002-20

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

3100220

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

S2008000131RevB

Service Bulletin/Repair Instructions

U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated

18-063-20 REV. A

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates The previous release for this PCM software has been removed. Software updates to correct issues will be re-released by the end of 4th quarter 2020.

1806320REVA

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates The previous release for this PCM software has been removed. Software updates to correct issues will be re-released by the end of 4th quarter 2020.

18-084-20 REV. A

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance

1808420REVA

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance

9001496

Service Bulletin/Repair Instructions

CAP, Engine Oil, Fill (O RING, Oil Filler Cap) For all model years, models and engines using oil fill caps with O-Ring seals: These O-Rings are now available for service. The green O-Ring is part 68029299A$. The black O-Ring is to be serviced by the green O-Ring. The blue O-Ring (thicker cross section than green & black) is part 68029300A$.~ If ordering this oil filler cap for a warranty repair due to a damaged/missing O-ring, please note that returned caps replaced for an O-ring issue will be subject to chargeback.

18-001-20 REV. A

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20200908 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20200908, for details on this service action.

18-088-20

Service Bulletin/Repair Instructions

Flash: Dosing Control Unit (DCU) Updates This bulletin involves reprogramming the DCU with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set:U05A3-00 - Invalid Data Received From Reductant Quality Module. P20F4-00 - Reductant Consumption Too Low. P20F5-00 - Reductant Consumption Too High. P208E-00 - Reductant Injector Stuck Closed - Bank 1 Unit 1.

S1823000054 Rev.

Service Bulletin/Repair Instructions

(Revision C) Hood Flutter or Shake While Driving

S2008000141

Service Bulletin/Repair Instructions

Navigation Shows Incorrect Location

S2008000062 Rev.

Service Bulletin/Repair Instructions

(Revision A) No Start, Check Engine Lamp On, Multiple Cluster Warning Lamps On

18-084-20

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance Plausibility.

21-045-20

Service Bulletin/Repair Instructions

Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience any one of the following: An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48-72 kph (30-45 mph). Poor shift quality or ?bump? experienced during 2-1 coast downs with light brake or no brake applied. Vehicle does not default to automatic drive. Paddle shifters are disabled. "Shift not allowed' displayed in cluster when attempting to upshift while already in 9th gear.

S2008000130

Service Bulletin/Repair Instructions

Radio UConnect GPS Based Trip Computer Missing

S2008000131

Service Bulletin/Repair Instructions

U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated

18-063-20

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition:Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Particulate matter (soot) sensor faults codes. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator

9003637

Service Bulletin/Repair Instructions

USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

S2021000004

Service Bulletin/Repair Instructions

Valve Body Learn Procedure On WiTech Shows The Transmission Is Not In The Proper Gear After Repairs

S2008000101

Service Bulletin/Repair Instructions

Blind Spot Indicator Light Remains On In High Ambient Temperatures

18-052-20

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(EMEA only equipped with Gas Particulate Filter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included:Software corrects an issue with the wrong cylinder identification if an injector circuit performance fault is set in the PCM:If any of the series of injector control circuit faults are set, please refer to the bullet-pointed list below to determine which injector to address.For reference, the correct injector circuit performance faults are listed below:P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. Customers may also experience the following condition:Audible noise from the Low Temperature Radiator (LTR) coolant pump, at low speeds. Abnormal noise from the radiator cooling fan. LTR runs too long after the engine is turned off.

1805220

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(EMEA only equipped with Gas Particulate Filter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included:Software corrects an issue with the wrong cylinder identification if an injector circuit performance fault is set in the PCM:If any of the series of injector control circuit faults are set, please refer to the bullet-pointed list below to determine which injector to address.For reference, the correct injector circuit performance faults are listed below:P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. Customers may also experience the following condition:Audible noise from the Low Temperature Radiator (LTR) coolant pump, at low speeds. Abnormal noise from the radiator cooling fan. LTR runs too long after the engine is turned off.

21-041-20

Service Bulletin/Repair Instructions

Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.

2104120

Service Bulletin/Repair Instructions

Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.

09-006-20 REV. B

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

0900620

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

S2008000093

Service Bulletin/Repair Instructions

Blind Spot Or Park Assist Warnings, False Activation

S1908000210

Service Bulletin/Repair Instructions

Hands Free Power Sliding Door And Liftgate Feature Operates Intermittently

S2018000008

Service Bulletin/Repair Instructions

Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)

S2008000089

Service Bulletin/Repair Instructions

SGW (Security Gateway Module) Setting DTC B235A-00 ECU In-Plant- Mode

S19080000047

Service Bulletin/Repair Instructions

Volume Uncontrollable Or Stuck On High

S1908000047

Service Bulletin/Repair Instructions

Volume Uncontrollable Or Stuck On High

S1908000079

Service Bulletin/Repair Instructions

Travellink Fuel Prices Are Incorrect

S2008000077

Service Bulletin/Repair Instructions

VP2R Radio Clock Not Keeping Time

09-006-20 REV. A

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

S2008000073

Service Bulletin/Repair Instructions

VP4 Panasonic Radio USB Software Update Error Codes And Guidelines For Recovery

09-006-20

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

18-047-20

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance

S2008000068

Service Bulletin/Repair Instructions

Intermittently The Stop/Start (ESS) System Is Inoperative

S1908000101

Service Bulletin/Repair Instructions

Remote Phone App Does Not Communicate With Vehicle Radio

23-015-20

Service Bulletin/Repair Instructions

Disinfectant Solution Recommended for COVID-19

S2008000062

Service Bulletin/Repair Instructions

No Start, Check Engine Lamp On, Multiple Cluster Warning Lamps On

S2008000059

Service Bulletin/Repair Instructions

Error Code 20 Message On the Radio Screen

S2008000060

Service Bulletin/Repair Instructions

Radio Issues With iPhone 11

S2008000061

Service Bulletin/Repair Instructions

Cluster Warning Lamps On, Vehicle Does Not Start, Battery Lamp Illuminates At Times During Driving

S2008000048

Service Bulletin/Repair Instructions

Phone Contacts Will Not Load

08-049-20

Service Bulletin/Repair Instructions

Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

9004221

Service Bulletin/Repair Instructions

HEADLAMP After performing the headlamp condensation clearing service procedure in Service Library (#0820118820), If the headlamp(s) is/are being replaced for a Moisture/Condensation issue, please e-mail pictures of the Moisture/Condensation issue to: FCA Redacted Content Then proceed with the repair. Questions?: Call FCA Redacted Content.

9004244

Service Bulletin/Repair Instructions

COOLER, Transmission Oil Work procedure to address fluid leak issue with the transmission oil cooler on the MP (Part # 68249191A$), KL (Part # 68399021A$) and RU (Part # 68217322A$) needs to be followed. Service Instructions for the Condition of a TOC fluid leak: 1) Mark the leakage area if visible to assist in diagnosis and determination of the area where the leak has occurred. 2) If fluid leak was caused by damage or leakage at the transmission oil cooler: - Replace transmission oil cooler - Test drive and verify no additional fluid leaks 3) If fluid leak was caused by leak at quick connect fittings: - Replace transmission oil cooler lines - Test drive and verify no additional fluid leaks

18-039-20

Service Bulletin/Repair Instructions

Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season

S2019000002

Service Bulletin/Repair Instructions

Hands On Steering Wheel Message In EVIC

S1823000053

Service Bulletin/Repair Instructions

Water Leak On Floor Near A Pillar

S2023000022

Service Bulletin/Repair Instructions

Window Slow To Raise Or Lower May Be Noisy

S2008000045

Service Bulletin/Repair Instructions

Apps Or Icons Grayed Out

S2008000046

Service Bulletin/Repair Instructions

Cruise Control Inoperative

S2018000003

Service Bulletin/Repair Instructions

Customer complaint may include MIL/Check Engine lamp on. Upon further inspection, fault code P219A - Bank 1 Air-Fuel Ratio Imbalance may be found in the powertrain control module (PCM) as pending, active, or stored. Other fault codes P1066, P1068, P106A, or P106C (Solenoid Valve Switch Off Time Out of Range) may also be stored. Customer may also complain about loss of power or engine running rough while P219A is active.

S1823000054

Service Bulletin/Repair Instructions

Hood Flutter or Shake While Driving

S1808000175

Service Bulletin/Repair Instructions

LED Front Fog Lamps Flicker Or Intermittently Light, Are Dim Or Inoperative. A U11E9, or B16FB-15 may be set

S1908000208

Service Bulletin/Repair Instructions

Satellite Radio Inoperative Radio Has Code B156B-13.

18-023-20

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0780 - Gear Shift Malfunction. P050B - Cold Start Ignition Timing Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. Customers may also comment on one or more of the following:Extended engine crank times or possibly a no start condition(South Korea with Sales Code EDD only). The engine fails to restart while in Engine Stop/Start (ESS) mode. This is usually accompanied withDTC P06EF.

08-034-20

Service Bulletin/Repair Instructions

Flash: Electric Power Steering (EPS) Module Enhancements This bulletin involves updating the EPS module with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:C1592-01 - Electronic Power Steering Motor Circuit - General Electrical Failure. C2217-00 - Electric Power Steering Module Internal.If C2217-00 is active and there is no steering assist with the engine running, this Bulletin does not apply. Normal diagnosis should be performed. In addition, customers may experience one or more of the following concerns:Vehicle may have a slight pull during heavy acceleration.The vehicle pull mentioned only applies to a potential torque steer condition which may occur under heavy acceleration. All other vehicle pulling symptoms need to be diagnosed separate from this bulletin. The customer may experience a warning notification ?Service Power Steering? in the Electronic Vehicle Information Center (EVIC).

08-032-20

Service Bulletin/Repair Instructions

Lane Departure and Park Assist Features Inoperable This bulletin involves performing a Proxi routine and calibrate Electronic Power Steering (EPS) Customers may notice the Odometer flashing. Upon further investigation the technician may find one of the following DTCs have been set:B2204-55 - ECU Configuration Mismatch - Not Configured. Customers may also describe the following condition:The lane departure and the park assist features do not work.

08-027-20

Service Bulletin/Repair Instructions

2.4L Ignition Coil Boot Replacement This bulletin involves replacing all four ignition coil insulating boots. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

S2023000013

Service Bulletin/Repair Instructions

Water Leak In Area Of A Pillar Or On Passenger Floor

S2008000013

Service Bulletin/Repair Instructions

Key Programming, Security Pin Request, Pin Invalid

S1805000006

Service Bulletin/Repair Instructions

ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

09-002-20 REV. A

Service Bulletin/Repair Instructions

Camshaft Whining Noise This bulletin involves replacing the camshaft. The customer may describe the following: An excessive whining noise coming from the engine. Whining noise can usually be heard at idle.

09-002-20

Service Bulletin/Repair Instructions

Camshaft Whining Noise This bulletin involves replacing the camshaft. The customer may describe the following:An excessive whining noise coming from the engine. Whining noise can usually be heard at idle.

S2008000009

Service Bulletin/Repair Instructions

2019 KL, Cherokee, Battery Dead, No Crank, No Start

08-125-19

Service Bulletin/Repair Instructions

Flash: Radio Frequency Hub Module (RF-HUB) Updates AN-K4MCA-08-20191203 Refer to China Joint Venture (JV) released document AN-K4MCA-08-20191203, for details on this service action.

08-119-19

Service Bulletin/Repair Instructions

Flash: Electric Power Steering (EPS) Module Enhancements - AN-K4MCA-19-20191030 Refer to China Joint Venture (JV) released document AN-K4MCA-19-20191030, for details on this service action.

9004037

Service Bulletin/Repair Instructions

COVER, Handle (Interior Liftgate Handle) For a concern of the liftgate handle or cover coming loose and falling off while functioning it and the vehicle build date is after 4/30/2019, please contact Joyce Elsner at (248) 705-9579 to get both the trim panel and outer handle set back for further analysis. If no response in 15 minutes, proceed with repair.

9004174

Service Bulletin/Repair Instructions

HANDS FREE ASSEMBLY, Power Liftgate For a concern of intermittent operation of the liftgate kick sensor, replacing this part with another AA level part will not resolve the concern. When the vehicle is in sleep mode (key off for more than 15 minutes) and an improper kick is detected, the module fails to send a signal for subsequent good kicks but is resolved with a key cycle. Engineering is working on a solution ETA Feb 2020. Do not replace with another AA level part for this concern or the issue will persist.

31-004-19

Service Bulletin/Repair Instructions

Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.

31-005-19

Service Bulletin/Repair Instructions

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.

3100319

Service Bulletin/Repair Instructions

Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.

3100419

Service Bulletin/Repair Instructions

Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.

3100519

Service Bulletin/Repair Instructions

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.

3100619

Service Bulletin/Repair Instructions

Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.

9003825

Service Bulletin/Repair Instructions

LATCH, Hood For the following concerns, please verify secondary plunger switch before replacing hood latch with primary switch. Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch.

18-023-19 REV. B

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance Plausibility.

18-024-19 REV. C

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. Customers may also comment on one or more of the following:Extended engine crank times or possibly a no start condition(South Korea with Sales Code EDD only). The engine fails to restart while in Engine Stop/Start (ESS) mode. This is usually accompanied withDTC P06EF.

18-089-19

Service Bulletin/Repair Instructions

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

1802319

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance Plausibility.

1802419

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. Customers may also comment on one or more of the following:Extended engine crank times or possibly a no start condition(South Korea with Sales Code EDD only). The engine fails to restart while in Engine Stop/Start (ESS) mode. This is usually accompanied withDTC P06EF.

1808919

Service Bulletin/Repair Instructions

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

25-001-19

Service Bulletin/Repair Instructions

Instrument Panel Cluster (IPC) Message about Diesel Particulate Filter (DPF) Regeneration

2500119

Service Bulletin/Repair Instructions

Instrument Panel Cluster (IPC) Message about Diesel Particulate Filter (DPF) Regeneration

08-108-19

Service Bulletin/Repair Instructions

Flash: Instrument Panel Cluster (IPC) Updates This bulletin involves updating the IPC with the latest available software. Customers may comment on one or more of the following:Messages such as ?Engine Will Not Restart In XXX KM, Refill DEF? or ?Engine Will Not Restart, Refill DEF? display in the Electronic Vehicle Information Center (EVIC) for three seconds then disappear. Arabic messages are not displayed correctly in the IPC.

9004150

Service Bulletin/Repair Instructions

SEAL, Input If looking to replace stubshaft due to ATX fluid leaking, do not replace PTU seals. None of the seals from the PTU side will need to be replaced whenever the ATX stubshaft is replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft, it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft - PTU input shaft spline interface.  PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.

18-024-19 REV. B

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak. Customers may also comment on one or more of the following: Extended engine crank times or possibly a no start condition(South Korea with Sales Code EDD only). The engine fails to restart while in Engine Stop/Start (ESS) mode. This is usually accompanied withDTC P06EF.

18-065-19 REV. A

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20191009 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20191009, for details on this service action.

18-024-19 REV. A

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one ormore of the following Diagnostic Trouble Codes (DTCs) have been set:P0456 - EVAP System Small Leak. P06EF - Engine Restart Performance. Customers may also comment on the following:The engine fails to restart while in Engine Stop/Start (ESS) mode. This is usually accompanied with DTC P06EF.

02-005-19 REV. A

Service Bulletin/Repair Instructions

Knock or Clunk Type Noise In Front Left Suspension This bulletin involves inspecting and possibly replacing the spring in the left front strut assembly. Knocking type noise coming from the front left side of the vehicle.

08-003-19 REV.C

Service Bulletin/Repair Instructions

Radio and Back-up Camera Enhancements This bulletin involves updating the radio software level to 1848.24. Customers may experience one or more of the following: Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Ghost Touch, features, modes and App?s changing without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first start the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Audio distortion (KL vehicles). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay® or Android Auto Google® maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. Personal Identification Number (PIN) clears and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. Intermittently requires an anti-theft code to be entered. Software update also includes software enhancement. SXM sound and behavior improvements.

02-005-19

Service Bulletin/Repair Instructions

Knock or Clunk Type Noise In Front Left Suspension This bulletin involves inspecting and possibly replacing the spring in the left front strut assembly. Knocking type noise coming from the front left side of the vehicle.

18-065-19

Service Bulletin/Repair Instructions

Flash: Powertrain Control Module (PCM) Updates - AN-K4-21-20190516 Refer to China Joint Venture (JV) released document AN-K4-21-20190516, for details on this service action.

08-003-19 REV. B

Service Bulletin/Repair Instructions

Radio and Back-up Camera Enhancements This bulletin involves updating the radio software level to 1848.24. Customers may experience one or more of the following:Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Ghost Touch, features, modes and App?s changing without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first start the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Audio distortion (KL vehicles). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay® or Android Auto Google® maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. Personal Identification Number (PIN) clears and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. Intermittently requires an anti-theft code to be entered. Software update also includes software enhancement.SXM sound and behavior improvements.

9003220

Service Bulletin/Repair Instructions

RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

21-029-19

Service Bulletin/Repair Instructions

Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. The customer may describe the following:Poor 1-2 or 2-3 upshifting.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.