S2208000045 REV.D
Service Bulletin/Repair Instructions
Backup Camera Poor Image Quality Inspection
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2208000045 REV.D
Backup Camera Poor Image Quality Inspection
S2523000003 REV.A
Door Latch, Handle And Ajar Additional Service Information.
08-075-26 REV. A
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2208000045 REV.C
Backup Camera Poor Image Quality Inspection
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
08-075-26
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
109871
POWER TRANSFER UNIT - NONE
109872
POWER TRANSFER UNIT - NONE
S1721000016 REV.B
Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked.
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
S2508000102
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S1805000006 REV.B
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
9100325 Rev 1
Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
9100645
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
9100653
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S258A000017
Door speaker Inoperative or No Sound
08-220-25
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
23-008-25
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
102934
THROTTLE BODY
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2523000003
Door Latch, Handle And Ajar Additional Service Information.
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100468
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
9100444
Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369692AD) is the proper repair.
9100445
Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369691AD) is the proper repair.
S2208000045 REV.B
Backup Camera Poor Image Quality Inspection
08-220-24
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience the following: ● A moan noise or shudder feeling from the rear axle during low speed cornering, most notable in a parking lot or low speed maneuvering. This bulletin involves reprogramming the DTCM with the latest available software.
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
23-004-24 REV. A
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
08-153-24
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
97892
SWITCH - BRAKE
2300424
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S248A000001
SOS and Assistance Call Not Working After Radio Exchange Unit Installed
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1721000016
Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked, Set.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
S2308000032
Intermittently The Vehicle exhibits No Crank No Start. Vehicle Goes Into Limp Home Mode. Multiple DTC?s And Warning Lights
S2108000093
Apple CarPlay Does Not Work Or Not Connecting
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
ZD7
Customer Satisfaction Notification ZD7 - Radio Software update
S238A000028
Radio Black Screen, Freezing, Reset, Cutting Out Or Inoperative Intermittently
ReferenceZD7
Customer Satisfaction Notification ZD7 - Radio Software Update
0814023
Radio Over The Air JR34.41F Updating to JR34.42F Software Version ? Mobile WiFi inoperative upon start up. ? WiFi hotspot gives ?No Internet? connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.41F to JR34.42F. NOTE: The National campaign for this FOTA update launched July 5, 2023.
BulletinA
Customer Satisfaction Notification ZD7 - Radio Software Update
1806423
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTC)s: ? **P24D1-00 -Particulate Matter Sensor Regeneration Incomplete. NOTE: This software update will help prevent P24D1-00 from setting.
0700723
Water Quality When Mixed With Engine Coolant
S238A000024
SOS, Assistance Calls Not Successful After Radio Replacement or Radio Software Update
9100142
Mirror
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S228A000028
Radio Remained On After Ignition Is Switched Off, Dead Battery From Excessive Radio Current Draw
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
0804523
Radio Over The Air Updating to 34.42 Software Version ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
08-038-23
Radio Over The Air JR34.3 Updating to JR34.32.Software Version Customers may experience one or more of the following: Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.
S2308000009
Electric Power Steering (EPS) Will Not Calibrate, Negative Response Error Code 0X10
08-022-23
Radio Over The Air Updating to 40.12 Software Version Mobile Wi-Fi inoperative upon start up. Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.
S2323000002
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
S2324000001
Passenger Front Carpet Is Wet or Damp
S2218000023
Malfunction Indicator Lamp (MIL) Illuminated. Diagnostic Trouble Code (DTC) U02A3 ? Lost Communication ith Particulate Matter (PM) Sensor, Set After PM Sensor Replacement.
08-003-22 REV. A
UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2008000131 Rev.
U11E9 Lost Communication with AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
0821422
Radio Over The Air Updates to JR34.3/JR34.4 and JR34.41
0818022
Radio Enhancements Software Level 1848.34 This bulletin involves updating the radio software level to 1848.34. Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch issue, features, modes and App?s change without drivers input (does not affect rearview camera). Wireless connectivity pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.
S1823000031
Flat Tow Or Recreational Towing KL Cherokee
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
0815022
Flash: Heating Ventilation and Air Conditioning (HVAC) Updates This bulletin involves reprogramming the HVAC module with the latest available software. Customers may experience the following: During a remote start, the heated wheel, seat, mirrors and/or the ElectricBack Light (EBL) may not turn on.
S228A000017
Battery Drain Suspected or "Identified" From USB or Media Hub
S2208000138
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S228A000004RevB
Panasonic VP4R Wi-Fi New Enrollment Pause
2302422
Headlamp Condensation Clearing Procedure This bulletin is to communicate the procedure for headlamp condensation clearing.
S228A000004RevA
Panasonic VP4R Wi-Fi New Enrollment Pause
S1523000016
A Rattle Or Creak Noise Is Heard From The Dual Pane Sunroof Area.
S228A000004
Panasonic VP4R Wi-Fi New Enrollment Pause
08-037-22
Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate the procedure for rear tail lamp condensation clearing. Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operatingtemperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e., a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into avapor. Turning the tail lamps on will usually accelerate this process.Clear Tail Lamp AssemblyTail Lamp Assembly with CondensationImages are not specific to vehicle, and only used for showing the tail lamps either clearFig. 1or having a condensation build up within the tail lamp assemblyFig. 2per the procedure.
1807922
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs have been set: P1D83 - Implausible Engine Oil Temperature Signal Received. P2610 - PCM Internal Engine Off Timer Performance. Customers may experience one or more of the following: An audible clunk after applying throttle from a coasting condition, predominantlyin fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph). Software was updated to better address this condition. A message on the instrument cluster stating ?Speed limiter ready? afterthe first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(Equipped with NH2 Sales Code Only). Inform the customer after the software update thatthe proper operative will be when the customer presses the speed limiter button twice, a messageon the instrument cluster stating ?Speed limiter ready? and the AVSL feature will work correctly (Equipped with NH2 Sales Code Only).
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2208000073
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
S1708000118
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S1708000118 RevB
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S2208000068
?Device Not Supported? Message on the radio screen
0800322
UAQ and UCQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth® pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.
18-090-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. Customers may also experience the following condition:When the cruise control is engaged and the Active Vehicle Speed Limiter (AVSL) button is pressed, Instrument Panel Cluster (IPC) display skips ?Cruise Control Canceled? message and displays ?Speed Limiter Ready?. In addition the following software enhancement are included:Improved idle after a hot restart.
S2108000204
Radio Lockup In The Software Installation Screen After Accepting FOTA Update (Incorrect "S2008000204" indicated on published document)
9004401
DIFFERENTIAL, Rear Axle (KL 4WD w/DK2 = 1-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM · 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · 68550586A$ service RDMs have a 20 clutch plate design · Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA · If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540645AA for the 24 plate RDM with a new pump. · Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M
9004402
DIFFERENTIAL, Rear Axle (KL 4WD w/DK4 = 2-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM · 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design · Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. · If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540646AA for the 24-plate RDM with a new pump. · Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti
S2008000131RevC
U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
S2108000062
U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
S2108000198
Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit
0500421
Front Click Noise at Low Speed Turns
S2108000170
Head unit button stuck DTC code B14DA-2A
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
0809921
UAQ and UCQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth® pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.
S2125000002
Customer complaint includes a Mil-on condition. Upon further investigation, one or more of the following fault codes may be set in the PCM:
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
S2008000059RevB
Error Code 20 Message On the Radio Screen
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S2008000059RevA
Error Code 20 Message On the Radio Screen
S2108000098RevB
Radio Screen Freeze, Blank Screen And Reset
S2108000127 Rev.
Radio Reboot Continually
S2108000127-1
Radio Reboot Continually
S2108000127REVA
Radio Reboot Continually
S2108000127RevA
Radio Reboot Continually
S2108000130
Bubbles Or Delamination On The Radio Display
S2108000119
Apple CarPlay Malfunctioning, Does Not Launch Or Is Cutting In An Out On Wired And Wireless Connection, Radio Stuck When IPhone Is Connected
S2108000127
Radio Reboot Continually
08-093-21
UAS, UAQ, UCS, UAV, UCV and UCQ Radio Over The Air Software Version Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay® connectivity improvement. Improvement to Bluetooth® phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.
0809321
UAS, UAQ, UCS, UAV, UCV and UCQ Radio Over The Air Software Version Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay® connectivity improvement. Improvement to Bluetooth® phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.
S2008000010
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
S2008000010 Rev.
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
S2108000120
Radio Volume Uncontrollable Or Changing On Its Own
OD21T001
Safety Recall Communication ? Continental Tire the Americas, LLC (?CTA?) Campaign #21T-001
S2108000098
Radio Screen Freeze, Blank Screen And Reset
S2108000098 Rev.
Radio Screen Freeze, Blank Screen And Reset
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
08-070-21
ULQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 34.2. If the software update is performed on a radio with software below 19.9, the radio could be damaged and will need to be replaced. Customers may experience one or more of the following:Lost radio presets. Radio display screen is black when the ignition is on. Radio may reset, turn itself off and then back on again. Park assist chime will continue to chime after the vehicle is turn off. Radio will display the incorrect speed limit in kph when approaching a road speed camera. In addition the following enhancements are included:Voice Recognition (VR) and Bluetooth® improvements. Improvements for Off-road pages.
0807021
ULQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 34.2. If the software update is performed on a radio with software below 19.9, the radio could be damaged and will need to be replaced. Customers may experience one or more of the following:Lost radio presets. Radio display screen is black when the ignition is on. Radio may reset, turn itself off and then back on again. Park assist chime will continue to chime after the vehicle is turn off. Radio will display the incorrect speed limit in kph when approaching a road speed camera. In addition the following enhancements are included:Voice Recognition (VR) and Bluetooth® improvements. Improvements for Off-road pages.
S1708000118 Rev.
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination After Key Off
S1908000107
Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated
S1908000107 Rev.
Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
08-060-21
Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate that a new procedure for rear tail lamp condensation clearing that is now available in the service information.
0806021
Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate that a new procedure for rear tail lamp condensation clearing that is now available in the service information.
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S2108000080
Radio Replacement Reset Routine, Radio Has Missing Icons Or Are Grayed Out
S2124000004
A/C does not cool and vehicle is low on Freon charge but no leak is found with sniffer or black light anywhere in the system
08-033-21
UGQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. The radio may need up tothree USB flash drivesto get the software level to 39.5 Customers may experience one or more of the following:No option to enable or disable the heated seat or steering wheel. Destination information will not clear. Voice Recognition (VR) stays in French while the language is set to English. Radio may reset after Bluetooth® phone receives two text messages one after another. False message displayed ?turn vehicle to run? or ? key on to access menu? when the ignition is already in the run position. Jeep off road page is missing. Latitude and Longitude values on the Jeep off road page is missing. Russian language missing. In addition, the following enhancement are included in this update:Add auto park brake functionality to the control setting in the radio.
0803321
UGQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. The radio may need up tothree USB flash drivesto get the software level to 39.5 Customers may experience one or more of the following:No option to enable or disable the heated seat or steering wheel. Destination information will not clear. Voice Recognition (VR) stays in French while the language is set to English. Radio may reset after Bluetooth® phone receives two text messages one after another. False message displayed ?turn vehicle to run? or ? key on to access menu? when the ignition is already in the run position. Jeep off road page is missing. Latitude and Longitude values on the Jeep off road page is missing. Russian language missing. In addition, the following enhancement are included in this update:Add auto park brake functionality to the control setting in the radio.
S2108000002 Rev.
In Cold Temperatures The Customer May Complain Of An Intermittent No Crank, Cranks And Stalls, Stops Cranking Fails To Start
S2108000002RevC
In Cold Temperatures The Customer May Complain Of An Intermittent No Crank, Cranks And Stalls, Stops Cranking Fails To Start
18-021-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC).P2610 - PCM Internal Engine Off Timer Performance. Customers may experience one or more of the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).Software was updated to better address this condition. A message on the instrument cluster stating ?Speed limiter ready? after the first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(Equipped with NH2 Sales Code Only).Inform the customer after the software update that the proper operative will be when the customer presses the speed limiter button twice, a message on the instrument cluster stating ?Speed limiter ready? and the AVSL featurewill work correctly (Equipped with NH2 Sales Code Only).
1802121
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC).P2610 - PCM Internal Engine Off Timer Performance. Customers may experience one or more of the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).Software was updated to better address this condition. A message on the instrument cluster stating ?Speed limiter ready? after the first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(Equipped with NH2 Sales Code Only).Inform the customer after the software update that the proper operative will be when the customer presses the speed limiter button twice, a message on the instrument cluster stating ?Speed limiter ready? and the AVSL featurewill work correctly (Equipped with NH2 Sales Code Only).
9004352
RELAY, Micro **This applies to the 2020 KL and 2021 KL Only!!** Owner reports in colder temperatures the vehicle may exhibit a No Start or and/or a Start and Stall fail to Start condition. Vehicle will start normally when PDC or vehicle is warmed up. This symptom may also be accompanied by DTC P1279 -STARTER CONTROL CIRCUIT 2 OPEN. Refer to SOL Publication S2108000002 REV B to ensure it is applicable to the vehicle prior to moving forward. For SOL S2108000002 REV B, the Denso 68406797AA may not be available / may be on Backorder. In the event 68406797AA is on backorder, another validated Denso relay to use is 68244159AA. Quantities for this relay are limited, we kindly request to only order on an as needed basis until mid March 2021 so customer vehicles currently exhibiting this issue can be repaired. CAUTION: Denso relay part number 68244159AA can only be used in the Run/Start relay location. Premature relay failure will occur if used in other locations. Other locations require relays which can handle higher duty cycle requirements. Note: Only the Run/Start relay will require replacement for the issue identified in S2108000002 REV B. No other Song Chuan relays should be replaced for this condition.
S2108000002RevB
In Cold Temperatures The Customer May Complain Of An Intermittent No Crank, Cranks And Stalls, Stops Cranking Fails To Start
S2108000045
Favorite Song On-Air Alert List Empty
08-015-21
Radio Enhancements This bulletin involves updating the radio software level to 1848.34. Customers may experience one or more of the following:Radio display screen flickers. Radio resets with RPM less than 1000 RPM (DT and JL with 3.0L Diesel). Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.
23-003-21
Rear Tires Rubbing On Splash Shields/Wheel Liners This bulletin involves inspecting for the wrong size tire and wheel assemblies and possibly replacing all five wheel assemblies, Tire Pressure Monitoring (TPM) sensors, flashing the Electronic Power Steering (EPS) and performing a Proxi alignment. Customers may experience the following condition: The rear 17 in. tires are rubbing on the wheel liners. This condition is due to an incorrect 17 in. tire and wheel size, for the North Edition packages that require 18 in. tires and wheels.
18-001-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC.P1614-00 - ECU Reset-Recovery Occurred(North America Only). Customers may experience a message on the instrument cluster stating "Speed Limiter Ready" after the first press of thespeed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(Sales Code NH2).Inform the customer after the software update that the proper operative will be when thecustomer presses the speed limiter button twice a message on the instrument cluster stating "Speed limiter ready" and the AVSL feature will workcorrectly(Sales Code NH2).
9004342
WINDSHIELD Windshield cracked or blemish. When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.
W43 Rev 1 Combo
Customer Satisfaction Notification W43 Tire Rub & Chrome Exhaust
S2108000002
In Extremely Cold Temperatures The Customer May Complain Of An Intermittent No Crank, Cranks And Stalls, Stops Cranking Fails To Start
S2023000047
Water Leak From A Pillar / Windshield Area
23-026-20 REV. A
Rear Tires Rubbing On Splash Shields/Wheel Liners This bulletin involves inspecting for the wrong size tire and wheel assemblies and possibly replacing all five wheel assemblies, Tire Pressure Monitoring (TPM) sensors, flashing the Electronic Power Steering (EPS) and performinga Proxi alignment. Customers may experience the following condition: The rear 17 in. tires are rubbing on the wheel liners. This conditionis due to an incorrect 17 in. tire and wheel size, for the North Edition packages that require 18 in. tires and wheels.
18-080-20 REV. A
Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20201101 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20201101, for details on this service action.
1808020
Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20201101 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20201101, for details on this service action.
9004335
Turbocharger If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed o-ring for a leak. The o-ring is serviced separately and complete turbo replacement may not be necessary.
18-105-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition: Engine Start/Stop inoperative after previous software update. Remote start inoperative (South Korea vehicles only). Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator
1810520
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition:Engine Start/Stop inoperative after previous software update. Remote start inoperative(South Korea vehicles only). Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator
S1908000194
(Rev. A) Hands Free Liftgate Takes Multiple Foot Kicks to Open After The Vehicle Enters A Full Bus Sleep Cycle
S1908000194 Rev.
(Rev. A) Hands Free Liftgate Takes Multiple Foot Kicks to Open After The Vehicle Enters A Full Bus Sleep Cycle
S2008000172
Radio Screen Flickering When Using Apple CarPlay Or Android Auto.
S2018000012
Check engine lamp on. Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.
23-026-20
Rear Wheels Rubbing On Splash Shields/Wheel Liners This bulletin involves inspecting for the wrong size tire and wheel assemblies and possibly replacing all five wheel assemblies, Tire Pressure Monitoring (TPM) sensors, flashing the Electronic Power Steering (EPS) and performing a Proxi alignment. Customers may experience the following condition:The rear 17 in. tires are rubbing on the wheel liners. This condition is due to an incorrect 17 in. tire and wheel size, for the North Edition packages that require 18 in. tires and wheels.
2302620
Rear Wheels Rubbing On Splash Shields/Wheel Liners This bulletin involves inspecting for the wrong size tire and wheel assemblies and possibly replacing all five wheel assemblies, Tire Pressure Monitoring (TPM) sensors, flashing the Electronic Power Steering (EPS) and performing a Proxi alignment. Customers may experience the following condition:The rear 17 in. tires are rubbing on the wheel liners. This condition is due to an incorrect 17 in. tire and wheel size, for the North Edition packages that require 18 in. tires and wheels.
W43
Customer Satisfaction Notification W43 Tire Rub & Chrome Exhaust
W43 Combo
Customer Satisfaction Notification W43 Tire Rub & Chrome Exhaust
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100220
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2008000162
Power Lift-gate Will Not Close From Power Lift-gate Button
S2008000131RevB
U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
07-002-20
Heater Hoses Installed Incorrectly This bulletin involves inspecting the heater hoses and possibly draining the engine coolant, swapping the heater hoses and refilling the engine coolant. Some vehicles may have been built with one or more of the following:Heater hoses installed in reversed order. If the coolant was drained and replaced, a sign the heater hoses are reversed is the vehicle will also make a gurgling noise.
0700220
Heater Hoses Installed Incorrectly This bulletin involves inspecting the heater hoses and possibly draining the engine coolant, swapping the heater hoses and refilling the engine coolant. Some vehicles may have been built with one or more of the following:Heater hoses installed in reversed order. If the coolant was drained and replaced, a sign the heater hoses are reversed is the vehicle will also make a gurgling noise.
18-085-20 REV. A
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC).P2610 - PCM Internal Engine Off Timer Performance. Customers may experience one or more of the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph). A message on the instrument cluster stating ?Speed limiter ready? after the first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(Equipped with NH2 Sales Code Only).Inform the customer after the software update that the proper operative will be when the customer presses the speed limiter button twice, a message on the instrument cluster stating ?Speed limiter ready?and the AVSL feature will work correctly (Equipped with NH2 Sales Code Only).
1808520REVA
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC).P2610 - PCM Internal Engine Off Timer Performance. Customers may experience one or more of the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph). A message on the instrument cluster stating ?Speed limiter ready? after the first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(Equipped with NH2 Sales Code Only).Inform the customer after the software update that the proper operative will be when the customer presses the speed limiter button twice, a message on the instrument cluster stating ?Speed limiter ready?and the AVSL feature will work correctly (Equipped with NH2 Sales Code Only).
23-007-20 REV. A
Hood Closing Effort This bulletin involves informing technicians that the hood should not be adjusted for closing effort being high. The customer may describe that the hood takes extra effort to close.
9001496
CAP, Engine Oil, Fill (O RING, Oil Filler Cap) For all model years, models and engines using oil fill caps with O-Ring seals: These O-Rings are now available for service. The green O-Ring is part 68029299A$. The black O-Ring is to be serviced by the green O-Ring. The blue O-Ring (thicker cross section than green & black) is part 68029300A$.~ If ordering this oil filler cap for a warranty repair due to a damaged/missing O-ring, please note that returned caps replaced for an O-ring issue will be subject to chargeback.
S1823000054 Rev.
(Revision C) Hood Flutter or Shake While Driving
S2008000141
Navigation Shows Incorrect Location
S2008000062 Rev.
(Revision A) No Start, Check Engine Lamp On, Multiple Cluster Warning Lamps On
18-085-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).
21-020-20 REV. A
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P1614 - ECU Reset-Recovery Occurred. Customers may also experience the following: An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48-72 kph (30-45 mph).
18-080-20
Flash: Powertrain Control Module (PCM) Updates - AN-K4-18-20200824 Refer to China Joint Venture (JV) released document AN-K4-18-20200824, for details on this service action.
18-006-20 REV. A
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC.P1614-00 - ECU Reset-Recovery Occurred(North America Only). Customers may experience a message on the instrument cluster stating " Speed limiter ready " after the first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(Sales Code NH2).Inform the customer after the software update that the proper operative will be when the customer presses the speed limiter button twice a message on the instrument cluster stating " Speed limiter ready " and the AVSL feature will work correctly(Sales Code NH2).
18-007-20 REV. A
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC).P2610 - PCM Internal Engine Off Timer Performance. Customers may also experience a message on the instrument cluster stating " Speed limiter ready " after the first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(equipped with NH2 Sales Code only).Inform the customer after the software update that the proper operative will be when the customer presses the speed limiter button twice a message on the instrument cluster stating " Speed limiter ready " and the AVSL feature will work correctly(equipped with NH2 Sales Code only).
1800620REVA
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC.P1614-00 - ECU Reset-Recovery Occurred(North America Only). Customers may experience a message on the instrument cluster stating " Speed limiter ready " after the first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(Sales Code NH2).Inform the customer after the software update that the proper operative will be when the customer presses the speed limiter button twice a message on the instrument cluster stating " Speed limiter ready " and the AVSL feature will work correctly(Sales Code NH2).
1800720REVA
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC).P2610 - PCM Internal Engine Off Timer Performance. Customers may also experience a message on the instrument cluster stating " Speed limiter ready " after the first press of the speed limiter button and the Active Vehicle Speed Limiter (AVSL) is inoperative(equipped with NH2 Sales Code only).Inform the customer after the software update that the proper operative will be when the customer presses the speed limiter button twice a message on the instrument cluster stating " Speed limiter ready " and the AVSL feature will work correctly(equipped with NH2 Sales Code only).
S2008000130
Radio UConnect GPS Based Trip Computer Missing
S2008000131
U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
23-021-20
A-Pillar Water Leak This bulletin involves partially removing both front wheel liners and adding spray foam near the body load beam ends, on each side of the vehicle. Customers may comment on the following:Wet front carpets inside the cabin near the driver, passenger or both, front floor A-pillar areas.
2302120
A-Pillar Water Leak This bulletin involves partially removing both front wheel liners and adding spray foam near the body load beam ends, on each side of the vehicle. Customers may comment on the following:Wet front carpets inside the cabin near the driver, passenger or both, front floor A-pillar areas.
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
11-003-20
Drone, Pop, or Rattle Noise From The Passenger Side Floor Area This bulletin involves inspecting the under floor exhaust system and possibly replacing the exhaust pipe assembly and gaskets. Customers may comment on one or more of the following:A drone, pop, or rattle noise, emitting from the passenger floor area while driving usually over large bumps or uneven pavement.
1100320
Drone, Pop, or Rattle Noise From The Passenger Side Floor Area This bulletin involves inspecting the under floor exhaust system and possibly replacing the exhaust pipe assembly and gaskets. Customers may comment on one or more of the following:A drone, pop, or rattle noise, emitting from the passenger floor area while driving usually over large bumps or uneven pavement.
S2021000004
Valve Body Learn Procedure On WiTech Shows The Transmission Is Not In The Proper Gear After Repairs
18-056-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may also experience the following condition:When the cruise control is engaged and the Active Vehicle Speed Limiter (AVSL) button is pressed, Instrument Panel Cluster (IPC) display skips ?Cruise Control Canceled? message and displays ?Speed Limiter Ready?. In addition the following software enhancement are included:Improved idle after a hot restart.
1805620
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may also experience the following condition:When the cruise control is engaged and the Active Vehicle Speed Limiter (AVSL) button is pressed, Instrument Panel Cluster (IPC) display skips ?Cruise Control Canceled? message and displays ?Speed Limiter Ready?. In addition the following software enhancement are included:Improved idle after a hot restart.
S2008000094
Uconnect Market Place APP Fatal Error Message
21-042-20
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:P1614-00 - ECU Reset-Recovery Occurred.
2104220
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:P1614-00 - ECU Reset-Recovery Occurred.
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
S1908000210
Hands Free Power Sliding Door And Liftgate Feature Operates Intermittently
S2018000008
Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)
S19080000047
Volume Uncontrollable Or Stuck On High
S1908000047
Volume Uncontrollable Or Stuck On High
S2008000077
VP2R Radio Clock Not Keeping Time
11-002-20
Missing Chrome Exhaust Tips This bulletin involves inspecting and replacing the muffler assembly if necessary. Customers may notice the chrome tips on the mufflers are missing when the Monroney label shows it should have them.
1100220
Missing Chrome Exhaust Tips This bulletin involves inspecting and replacing the muffler assembly if necessary. Customers may notice the chrome tips on the mufflers are missing when the Monroney label shows it should have them.
S2023000029
Drone Pop Noise From Passenger Side Floor Area
S2008000073
VP4 Panasonic Radio USB Software Update Error Codes And Guidelines For Recovery
09-003-20 REV. C
Inspect Throttle Body Assembly This bulletin involves inspecting the Julian date on the throttle body and possibly replacing it. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P2100 - Electronic Throttle Control Motor Circuit/Open - Bank 1. The customer may also describe the vehicle is in limp home mode.
W28
Customer Satisfaction Notification U28 Uconnect App
08-053-20
UAQ and UCQ Radio Enhancements This bulletin provides information regarding a radio software update 34.2, which is part of a safety recall. Customers may experience one or more of the following:Hard buttons on rearview mirror do not launch SOS or Assist Calls. Inaccurate clock time. Bluetooth® device is slow to pair. Loss of saved radio presets. No audio output coming from the radio. Can not control audio volume. Rear view camera display will not turn on. GPS unable to load and find location. Voice recognition unable to recognize contact to place calls. Phone book is unable to load/sync.
23-015-20
Disinfectant Solution Recommended for COVID-19
S2008000062
No Start, Check Engine Lamp On, Multiple Cluster Warning Lamps On
S2008000059
Error Code 20 Message On the Radio Screen
S2008000060
Radio Issues With iPhone 11
S2008000048
Phone Contacts Will Not Load
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
9004221
HEADLAMP After performing the headlamp condensation clearing service procedure in Service Library (#0820118820), If the headlamp(s) is/are being replaced for a Moisture/Condensation issue, please e-mail pictures of the Moisture/Condensation issue to: FCA Redacted Content Then proceed with the repair. Questions?: Call FCA Redacted Content.
9004244
COOLER, Transmission Oil Work procedure to address fluid leak issue with the transmission oil cooler on the MP (Part # 68249191A$), KL (Part # 68399021A$) and RU (Part # 68217322A$) needs to be followed. Service Instructions for the Condition of a TOC fluid leak: 1) Mark the leakage area if visible to assist in diagnosis and determination of the area where the leak has occurred. 2) If fluid leak was caused by damage or leakage at the transmission oil cooler: - Replace transmission oil cooler - Test drive and verify no additional fluid leaks 3) If fluid leak was caused by leak at quick connect fittings: - Replace transmission oil cooler lines - Test drive and verify no additional fluid leaks
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
S1823000053
Water Leak On Floor Near A Pillar
S2023000022
Window Slow To Raise Or Lower May Be Noisy
S2008000045
Apps Or Icons Grayed Out
S2008000046
Cruise Control Inoperative
S2018000003
Customer complaint may include MIL/Check Engine lamp on. Upon further inspection, fault code P219A - Bank 1 Air-Fuel Ratio Imbalance may be found in the powertrain control module (PCM) as pending, active, or stored. Other fault codes P1066, P1068, P106A, or P106C (Solenoid Valve Switch Off Time Out of Range) may also be stored. Customer may also complain about loss of power or engine running rough while P219A is active.
S1823000054
Hood Flutter or Shake While Driving
S1808000175
LED Front Fog Lamps Flicker Or Intermittently Light, Are Dim Or Inoperative. A U11E9, or B16FB-15 may be set
S1908000208
Satellite Radio Inoperative Radio Has Code B156B-13.
09-003-20 REV. B
Inspect Throttle Body Assembly This bulletin involves inspecting the Julian date on the throttle body and possibly replacing it. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P2100 - Electronic Throttle Control Motor Circuit/Open - Bank 1. The customer may also describe the following:The vehicle is in limp home mode.
S2008000022
Service 4WD Lamp On, 4WD System Unavailable Service Required Message Displayed On Cluster
21-020-20
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P1614 - ECU Reset-Recovery Occurred.
09-003-20 REV. A
Inspect Throttle Body Assembly This bulletin involves inspecting the Julian date on the throttle body and possibly replacing it. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P2100 - Electronic Throttle Control Motor Circuit/Open - Bank 1. The customer may also describe the following:The vehicle is in limp home mode.
08-035-20
Flash: Radio Frequency Hub Module (RF-HUB) Updates This bulletin involves reprogramming the RF-HUB with the latest software available. The customer may describe that the Uconnect remote function inoperable when using the phone/mobile App.Remote operations from the Uconnect app, listed below, are inoperative:Remote operations/Remote commands using the app for Lock, Unlock and Remote start.
08-032-20
Lane Departure and Park Assist Features Inoperable This bulletin involves performing a Proxi routine and calibrate Electronic Power Steering (EPS) Customers may notice the Odometer flashing. Upon further investigation the technician may find one of the following DTCs have been set:B2204-55 - ECU Configuration Mismatch - Not Configured. Customers may also describe the following condition:The lane departure and the park assist features do not work.
S2023000013
Water Leak In Area Of A Pillar Or On Passenger Floor
S2008000013
Key Programming, Security Pin Request, Pin Invalid
S1805000006
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
09-003-20
Inspect Throttle Body Assembly This bulletin involves inspecting the Julian date on the throttle body and possibly replacing it. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P2100 - Electronic Throttle Control Motor Circuit/Open - Bank 1. The customer may also describe the following:The vehicle is in limp home mode.
09-002-20 REV. A
Camshaft Whining Noise This bulletin involves replacing the camshaft. The customer may describe the following: An excessive whining noise coming from the engine. Whining noise can usually be heard at idle.
09-002-20
Camshaft Whining Noise This bulletin involves replacing the camshaft. The customer may describe the following:An excessive whining noise coming from the engine. Whining noise can usually be heard at idle.
23-007-20
Hood Closing Effort This bulletin involves informing technicians that the hood should not be adjusted for closing effort being high. The customer may describe that the hood takes extra effort to close.
08-124-19
Radio Enhancements This bulletin involves updating the radio software level to 1848.24. Customers may experience one or more of the following: Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
25-001-19
Instrument Panel Cluster (IPC) Message about Diesel Particulate Filter (DPF) Regeneration
2500119
Instrument Panel Cluster (IPC) Message about Diesel Particulate Filter (DPF) Regeneration
9004150
SEAL, Input If looking to replace stubshaft due to ATX fluid leaking, do not replace PTU seals. None of the seals from the PTU side will need to be replaced whenever the ATX stubshaft is replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft, it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft - PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.
04-001-19
Pentastar Upgrade Oil Fill Level after an Oil Change This bulletin involves rechecking the oil fill level after filling the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.