S2208000045 REV.D
Service Bulletin/Repair Instructions
Backup Camera Poor Image Quality Inspection
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2208000045 REV.D
Backup Camera Poor Image Quality Inspection
S2523000003 REV.A
Door Latch, Handle And Ajar Additional Service Information.
08-075-26 REV. A
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2208000045 REV.C
Backup Camera Poor Image Quality Inspection
9100778
If replacing $8474412A$ with $8474413A$ version, verify vehicle is proxied and configured properly. The 4412 part does not have RSD (SXM) capability. The 4413 part has RSD (SXM) capability and will not have an antenna connected. If replacement radio does not function, verify RSD sales code is added to configurator.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
08-075-26
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
109871
POWER TRANSFER UNIT - NONE
109872
POWER TRANSFER UNIT - NONE
S1721000016 REV.B
Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked.
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
S2508000102
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S1805000006 REV.B
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
9100325 Rev 1
Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
9100645
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
9100653
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S258A000017
Door speaker Inoperative or No Sound
08-220-25
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
9100458
Engine Complete With scope to reduce cost per repair, Stellantis Engineering ask to use long block instead of engine complete replacement for GME T4 DOHC. Before to replace Long Block Engineering is asking to follow these checks for an overheating suspect diagnosis: 1) BLOC-CHECK-KIT (BLOCK TESTER or CO2 Tester) 2) CYLINDER LEAKAGE TEST 3) COOLING SYSTEM LEAKS -INTERNAL ENGINE LEAKAGE INSPECTION If no one of this checks (1-2-3) fails it does not need to replace long block ( even less full engine) but just the component causing the coolant leak.
23-008-25
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
102934
THROTTLE BODY
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2523000003
Door Latch, Handle And Ajar Additional Service Information.
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100468
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
9100444
Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369692AD) is the proper repair.
9100445
Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369691AD) is the proper repair.
S2208000045 REV.B
Backup Camera Poor Image Quality Inspection
08-220-24 REV. A
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience the following: ● A moan noise or shudder feeling from the rear axle during low speed cornering, most notable in a parking lot or low speed maneuvering. This bulletin involves reprogramming the DTCM with the latest available software.
08-220-24
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience the following: ● A moan noise or shudder feeling from the rear axle during low speed cornering, most notable in a parking lot or low speed maneuvering. This bulletin involves reprogramming the DTCM with the latest available software.
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
23-004-24 REV. A
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
08-153-24
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
18-057-24
Flash: Powertrain Control Module (PCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** ● P02EE - Cylinder 1 Injector Circuit Performance. ● P02EF - Cylinder 2 Injector Circuit Performance. ● P02F0 - Cylinder 3 Injector Circuit Performance. ● P02F1 - Cylinder 4 Injector Circuit Performance. **Customers may also comment on one or more of the following: ● Cruise control inoperable. ● Lack of power after being in prolonged heat. ● Engine Stop/Start (ESS) is not working.** This bulletin involves reprogramming the PCM with the latest available software.
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
97892
SWITCH - BRAKE
0802824
Radio Over The Air Update from QR39.82F to QR40.12 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
0802624
Radio Over The Air Update from QR39.5 to QR40.11 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.5 to QR40.11. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
0802524
Radio Over The Air Updating to QR40.12 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.
2300424
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
0824523
Radio Over The Air Update to Q339.3 to QR39.62 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.
S1721000016
Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked, Set.
0823023
Radio Over The Air Updating From QR39.6 to QR40.12 Software Version Customers may experience one or more of the following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.
S238A000048
Radio Reset After Clock Adjustment
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9004542
Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
2400623
A/C Diagnostic LOP Change
S2308000032
Intermittently The Vehicle exhibits No Crank No Start. Vehicle Goes Into Limp Home Mode. Multiple DTC?s And Warning Lights
S2108000093
Apple CarPlay Does Not Work Or Not Connecting
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
ZD7
Customer Satisfaction Notification ZD7 - Radio Software update
0818123
Radio Over The Air Updating to QR40.12 Software Version ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.62 and QR39.57 to QR40.12. NOTE: National launch for this FOTA update is expected to begin August 16, 2023
S238A000034
USB Hub In-Operable
S238A000028
Radio Black Screen, Freezing, Reset, Cutting Out Or Inoperative Intermittently
ReferenceZD7
Customer Satisfaction Notification ZD7 - Radio Software Update
BulletinA
Customer Satisfaction Notification ZD7 - Radio Software Update
0700723
Water Quality When Mixed With Engine Coolant
S238A000024
SOS, Assistance Calls Not Successful After Radio Replacement or Radio Software Update
9100142
Mirror
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
0806423
Radio Over The Air Updating to QR40.12 Software Version Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.
2302923
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S228A000028
Radio Remained On After Ignition Is Switched Off, Dead Battery From Excessive Radio Current Draw
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2308000009
Electric Power Steering (EPS) Will Not Calibrate, Negative Response Error Code 0X10
08-022-23
Radio Over The Air Updating to 40.12 Software Version Mobile Wi-Fi inoperative upon start up. Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.
S2323000002
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
S2324000001
Passenger Front Carpet Is Wet or Damp
08-003-22 REV. A
UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2008000131 Rev.
U11E9 Lost Communication with AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
9100008
Telematic box module 2
9100096
Base Headlamp Bright, Base Headlamp Black
S1823000031
Flat Tow Or Recreational Towing KL Cherokee
0816922
Flash: Blind Spot Monitor (BSM) System Updates This bulletin involves updating the Left and Right Blind Spot Sensor (LBSS/RBSS) latest available software. The customer may experience the following: False alerts from the blind spot system, with no vehicle in the blind spot zones.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
0815022
Flash: Heating Ventilation and Air Conditioning (HVAC) Updates This bulletin involves reprogramming the HVAC module with the latest available software. Customers may experience the following: During a remote start, the heated wheel, seat, mirrors and/or the ElectricBack Light (EBL) may not turn on.
S228A000017
Battery Drain Suspected or "Identified" From USB or Media Hub
S2208000138
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2225000002
Upon scan tool inspection, DTCs for P0133-O2 Sensor Circuit Slow Response 1/1 and P0153-O2 Sensor Circuit Slow Response 2/1 may be present in the Powertrain Control Module (PCM) in a PENDING STATE ONLY (not Active or Stored). This may occur on very low mileage vehicles after the vehicle?s very first Stop/Start (ESS) event.
S228A000004RevB
Panasonic VP4R Wi-Fi New Enrollment Pause
1812022
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs have been set: P1D83 - Implausible Engine Oil Temperature Signal Received. U0418 Implausible Data Received From Brake System Control Module. DTC U0418 can be set erroneously due to a low battery (below 10 volts).Customers may experience the following: An audible clunk after applying throttle from a coasting condition, predominantlyin fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).
2302422
Headlamp Condensation Clearing Procedure This bulletin is to communicate the procedure for headlamp condensation clearing.
S228A000004RevA
Panasonic VP4R Wi-Fi New Enrollment Pause
0811822
Adaptive Cruise Control (ACC) Updates This bulletin involves a service procedure/adjustment to the ACC system. The vehicle may come in with the following Diagnostic Trouble Code (DTC): C14A4-00 - Sensor Adjustment Required. The customer may also describe that the Adaptive Cruise Control (ACC) is not functioning properly.
S1523000016
A Rattle Or Creak Noise Is Heard From The Dual Pane Sunroof Area.
S228A000004
Panasonic VP4R Wi-Fi New Enrollment Pause
18-078-22
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs have been set: P0031 - O2 Sensor 1/1 Heater Circuit Low. U0418 - Implausible Data Received From Brake System Control Module. DTC U0418 can be set erroneously due to a low battery (below 10 volts).
08-037-22
Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate the procedure for rear tail lamp condensation clearing. Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operatingtemperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e., a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into avapor. Turning the tail lamps on will usually accelerate this process.Clear Tail Lamp AssemblyTail Lamp Assembly with CondensationImages are not specific to vehicle, and only used for showing the tail lamps either clearFig. 1or having a condensation build up within the tail lamp assemblyFig. 2per the procedure.
S2223000035
Blind Spot System False Alerts. Blind Spot Indicator On In Mirror For No Reason.
S2208000095
Map, Dome, Overhead Console (OHC) Lamps Inoperative
1807822
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Code (DTC): U0418 - Implausible Data Received From Brake System Control Module. DTC U0418 can be set erroneously due to a low battery (below 10 volts).
1807322
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P2097 - Downstream Fuel Trim System 1 Rich. P2099 - Downstream Fuel Trim System 2 Rich.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2208000073
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
S1708000118
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S1708000118 RevB
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S2208000068
?Device Not Supported? Message on the radio screen
0800322
UAQ and UCQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth® pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.
S2108000204
Radio Lockup In The Software Installation Screen After Accepting FOTA Update (Incorrect "S2008000204" indicated on published document)
S2008000131RevC
U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
S2108000062
U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
S2108000198
Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit
S2108000181RevA
Media Hub And Or Wireless Charging Pad Is Inoperative
S2108000181a
Media Hub And Or Wireless Charging Pad Is Inoperative
S2108000170
Head unit button stuck DTC code B14DA-2A
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
75745
HUB AND BEARING - WHEEL
75610
BASE - FLOOR CONSOLE
75567
LATCH - FRONT DOOR
75490
CAMSHAFT - INTAKE
75227
MUFFLER AND TAILPIPE ? EXHAUST
S2125000002
Customer complaint includes a Mil-on condition. Upon further investigation, one or more of the following fault codes may be set in the PCM:
75446
GLASS - SUNROOF
0808821
Radio Enhancements This bulletin involves updating the radio software level to 2036.06. Customers may experience the following: Ghost Touch, features, modes and App?s changing without drivers input. Product plan UUID is not correct in Carplay®. Carplay audio does not always resume. Battery save vs. Battery Charge toggles back to Battery Charge after sleep cycle. When ?Charge Now? is selected on key-off outside of the charging schedule ? it does nothing. In addition, the following enhancements are included:Update power supply source from 1 amp to 2.1 amps. GOOGLE® certification enhancements - screen flickers
0808821REVA
Radio Enhancements This bulletin involves updating the radio software level to 2036.06. Customers may experience the following: Ghost Touch, features, modes and App?s changing without drivers input. Product plan UUID is not correct in Carplay®. Carplay audio does not always resume. Battery save vs. Battery Charge toggles back to Battery Charge after sleep cycle. When ?Charge Now? is selected on key-off outside of the charging schedule ? it does nothing. In addition, the following enhancements are included:Update power supply source from 1 amp to 2.1 amps. GOOGLE® certification enhancements - screen flickers
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
75267
TUBE - TURBO WATER FEED
S2108000098RevB
Radio Screen Freeze, Blank Screen And Reset
S2108000127 Rev.
Radio Reboot Continually
S2108000127-1
Radio Reboot Continually
S2108000127REVA
Radio Reboot Continually
S2108000127RevA
Radio Reboot Continually
S2108000130
Bubbles Or Delamination On The Radio Display
S2108000119
Apple CarPlay Malfunctioning, Does Not Launch Or Is Cutting In An Out On Wired And Wireless Connection, Radio Stuck When IPhone Is Connected
S2108000127
Radio Reboot Continually
S2008000010
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
S2008000010 Rev.
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
08-088-21
Radio Enhancements This bulletin involves updating the radio software level to 2036.06. Customers may experience the following:Product plan UUID is not correct in Carplay®. Carplay audio does not always resume. Battery save vs. Battery Charge toggles back to Battery Charge after sleep cycle. When ?Charge Now? is selected on key-off outside of the charging schedule ? it does nothing. In addition, the following enhancements are included:Update power supply source from 1 amp to 2.1 amps. GOOGLE® certification enhancements - screen flickers
S2108000120
Radio Volume Uncontrollable Or Changing On Its Own
S2108000098
Radio Screen Freeze, Blank Screen And Reset
S2108000098 Rev.
Radio Screen Freeze, Blank Screen And Reset
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
S2123000030
Lumbar Adjustment Not Working
S1908000107
Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated
S1908000107 Rev.
Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
08-060-21
Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate that a new procedure for rear tail lamp condensation clearing that is now available in the service information.
0806021
Rear Tail Lamp Condensation Clearing Procedure This bulletin is to communicate that a new procedure for rear tail lamp condensation clearing that is now available in the service information.
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S2108000080
Radio Replacement Reset Routine, Radio Has Missing Icons Or Are Grayed Out
18-019-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following Diagnostic Trouble Codes (DTCs). P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance.
1801921
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following Diagnostic Trouble Codes (DTCs). P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance.
S2124000004
A/C does not cool and vehicle is low on Freon charge but no leak is found with sniffer or black light anywhere in the system
S2108000002 Rev.
In Cold Temperatures The Customer May Complain Of An Intermittent No Crank, Cranks And Stalls, Stops Cranking Fails To Start
S2108000002RevC
In Cold Temperatures The Customer May Complain Of An Intermittent No Crank, Cranks And Stalls, Stops Cranking Fails To Start
9004352
RELAY, Micro **This applies to the 2020 KL and 2021 KL Only!!** Owner reports in colder temperatures the vehicle may exhibit a No Start or and/or a Start and Stall fail to Start condition. Vehicle will start normally when PDC or vehicle is warmed up. This symptom may also be accompanied by DTC P1279 -STARTER CONTROL CIRCUIT 2 OPEN. Refer to SOL Publication S2108000002 REV B to ensure it is applicable to the vehicle prior to moving forward. For SOL S2108000002 REV B, the Denso 68406797AA may not be available / may be on Backorder. In the event 68406797AA is on backorder, another validated Denso relay to use is 68244159AA. Quantities for this relay are limited, we kindly request to only order on an as needed basis until mid March 2021 so customer vehicles currently exhibiting this issue can be repaired. CAUTION: Denso relay part number 68244159AA can only be used in the Run/Start relay location. Premature relay failure will occur if used in other locations. Other locations require relays which can handle higher duty cycle requirements. Note: Only the Run/Start relay will require replacement for the issue identified in S2108000002 REV B. No other Song Chuan relays should be replaced for this condition.
S2108000002RevB
In Cold Temperatures The Customer May Complain Of An Intermittent No Crank, Cranks And Stalls, Stops Cranking Fails To Start
S2108000045
Favorite Song On-Air Alert List Empty
9004342
WINDSHIELD Windshield cracked or blemish. When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.
S2108000002
In Extremely Cold Temperatures The Customer May Complain Of An Intermittent No Crank, Cranks And Stalls, Stops Cranking Fails To Start
18-101-20 REV. A
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).
S2023000047
Water Leak From A Pillar / Windshield Area
S2008000172
Radio Screen Flickering When Using Apple CarPlay Or Android Auto.
S2018000012
Check engine lamp on. Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.
69484
Safety Recall W81 2021 Jeep Cherokee Front Lower Control Arm
18-101-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).
1810120
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).
21-050-20
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).
2105020
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience the following:An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48 - 72 kph (30 - 45 mph).
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.