S2208000045 REV.D
Service Bulletin/Repair Instructions
Backup Camera Poor Image Quality Inspection
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2208000045 REV.D
Backup Camera Poor Image Quality Inspection
S2523000003 REV.A
Door Latch, Handle And Ajar Additional Service Information.
08-075-26 REV. A
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2208000045 REV.C
Backup Camera Poor Image Quality Inspection
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
08-075-26
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
109871
POWER TRANSFER UNIT - NONE
109872
POWER TRANSFER UNIT - NONE
S1721000016 REV.B
Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked.
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
108458
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
108461
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
S2508000102
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S1805000006 REV.B
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
9100325 Rev 1
Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S258A000017
Door speaker Inoperative or No Sound
08-220-25
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100599
Underhood start/stop safety The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
23-008-25
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
102934
THROTTLE BODY
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2523000003
Door Latch, Handle And Ajar Additional Service Information.
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100468
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
9100444
Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369692AD) is the proper repair.
9100445
Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369691AD) is the proper repair.
S2208000045 REV.B
Backup Camera Poor Image Quality Inspection
08-220-24 REV. A
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience the following: ● A moan noise or shudder feeling from the rear axle during low speed cornering, most notable in a parking lot or low speed maneuvering. This bulletin involves reprogramming the DTCM with the latest available software.
S2408000003 REV.A
“Forward Collision Warning (FCW) Unavailable Service Required” message or a Service Active Lane Management Warning Light ‘ON'
101095
Bracket - Fender Mounting
08-220-24
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience the following: ● A moan noise or shudder feeling from the rear axle during low speed cornering, most notable in a parking lot or low speed maneuvering. This bulletin involves reprogramming the DTCM with the latest available software.
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
23-004-24 REV. A
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2408000015 REV.C
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
08-153-24
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
23-038-24
Passenger Heated Seat Cushion Inoperative Customer may experience the following: ● Passenger heated seat does not work.
21-030-24
Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0810-00 - Clutch Position Control Error. ● P16F0-00 - SPI Comm Hardware Fault. Customers may also comment on one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning indicator is on. NOTE: Require key cycle to recover. ● Shifts rough occasionally when coming down to a stop. ● Shifts rough occasionally when accelerating. ● Shifts rough when transitioning from EV to Hybrid operation on low SoC. ● Shifts rough when engines starts. ● On part throttle accelerations with little to no battery available the transition from battery power to engine on is harsh and abrupt. ● The engine oil life on dashboard drops down too fast when the engine oil dilution reaches high level without the ability to recover. **This bulletin involves reprogramming the TCM with the latest available software.** NOTE: **Please be sure that the 04B recall is completed prior to performing this TSB. This TCM software update is covered by the 04B recall if still incomplete.**
23-026-24 REV. A
Front Door Nameplate is Loose Customers may experience the following: ● The left, right or both front door nameplates or flags are not adhering (loose) to the door panel. Letters may have fallen off Fig. 1 from the nameplate assembly. This bulletin involves inspecting both front door nameplate assemblies for missing or loose letters/flag and possibly replacing one or both front door nameplate assemblies.
97892
SWITCH - BRAKE
0802824
Radio Over The Air Update from QR39.82F to QR40.12 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
0802624
Radio Over The Air Update from QR39.5 to QR40.11 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.5 to QR40.11. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
0802524
Radio Over The Air Updating to QR40.12 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.
2300424
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
0824523
Radio Over The Air Update to Q339.3 to QR39.62 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.
9100264
PSU Oil Pump Assy
S1721000016
Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked, Set.
0823023
Radio Over The Air Updating From QR39.6 to QR40.12 Software Version Customers may experience one or more of the following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.
S238A000048
Radio Reset After Clock Adjustment
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
S2323000075
2nd Row Center Seat Lazy Or Slow When Folding.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
2400623
A/C Diagnostic LOP Change
S2308000032
Intermittently The Vehicle exhibits No Crank No Start. Vehicle Goes Into Limp Home Mode. Multiple DTC?s And Warning Lights
S2108000093
Apple CarPlay Does Not Work Or Not Connecting
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0818123
Radio Over The Air Updating to QR40.12 Software Version ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.62 and QR39.57 to QR40.12. NOTE: National launch for this FOTA update is expected to begin August 16, 2023
S238A000034
USB Hub In-Operable
S238A000028
Radio Black Screen, Freezing, Reset, Cutting Out Or Inoperative Intermittently
9100160
Power wndow switch passenger
1807523
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P219A - Bank 1 Air-Fuel Ratio Imbalance. This bulletin involves reprogramming the PCM with the latest available software.
S2308000068
Front Inverter Outlet and Rear Center Console Power
0700723
Water Quality When Mixed With Engine Coolant
9100153A
B2768-49 Right Impact Pressure Sensor-Internal Failure, prior to replacement of any components please contact FCA Redacted Content for further assistance. If no response in 15 minutes, proceed with repair.
S238A000024
SOS, Assistance Calls Not Successful After Radio Replacement or Radio Software Update
0700523
Engine Coolant Leak Coolant leak under vehicle and/or low coolant warning on dash. This bulletin involves inspecting and replacing the ECT sensor if required.
0812023
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) or warning lamp illumination. Upon further investigation the technician may find that the multiple Diagnostic Trouble Codes (DTCs) have been set: ? C1403-29 - Transfer Case Range Position Sensor-Signal Invalid. ? C14AA-62 - Transfer Case Motor Position Sensor Supply-Signal Compare Failure. This bulletin involves reprogramming the DTCM with the latest software available.
9100142
Mirror
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
Newsletter
FCA CARIBBEAN WARRANTY OPERATIONS NEWSLETTER
9100158
Power Window 1 Gang Before Replacing the Switch, please verify the following: 1- Check the switch internal resistance to verify the values are within specification stated in the service procedures. 2- Swap the switch with the issue with the other side. This switch is used in both rear doors. If after the swap the issue is now present at the other door and the original door position no longer has the issue, replace the switch.
0806423
Radio Over The Air Updating to QR40.12 Software Version Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.
2302923
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.
2302623A
Gap At Front Door Panels Either or both front door inside trim panels are loose or have a gap at the doors. This bulletin involves re-securing the front door trim panels to the doors.
S2108000015
Uconnect Box Require Service Message
2302623
Gap At Front Door Panels Either or both front door inside trim panels are loose or have a gap at the doors. This bulletin involves re-securing the front door trim panels to the doors.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.