U67 Combo Rev11
Warranty Program/Extension
Emissions Recall U67 - Catalytic Converter Efficiency - Dealer Notification (Revision 11)
Vehicle report
2015 JEEP COMPASS
Service bulletins
131 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
9100645
Service Bulletin/Repair Instructions
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
9100653
Service Bulletin/Repair Instructions
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
103954
Service Bulletin/Repair Instructions
ACTUATOR - A/C AND HEATER
104087
Service Bulletin/Repair Instructions
ACTUATOR - A/C AND HEATER
S1408000384
Service Bulletin/Repair Instructions
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
Service Bulletin/Repair Instructions
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Service Bulletin/Repair Instructions
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Service Bulletin/Repair Instructions
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
Service Bulletin/Repair Instructions
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Service Bulletin/Repair Instructions
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Service Bulletin/Repair Instructions
Water Quality When Mixed With Engine Coolant
1804823
Service Bulletin/Repair Instructions
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
U67 Combo Rev10
Service Bulletin/Repair Instructions
Emissions recal U67 Catalytic Converter Efficiency
U67
Service Bulletin/Repair Instructions
Some of the above-involved vehicles may exceed NOx (Oxides of Nitrogen) emission level standards due to loss of catalytic converter efficiency
3100122
Service Bulletin/Repair Instructions
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
Service Bulletin/Repair Instructions
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
V51
Service Bulletin/Repair Instructions
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
S2108000163
Service Bulletin/Repair Instructions
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Service Bulletin/Repair Instructions
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
9004386
Service Bulletin/Repair Instructions
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
9004378
Service Bulletin/Repair Instructions
KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
S1608000226
Service Bulletin/Repair Instructions
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S16080002261
Service Bulletin/Repair Instructions
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Service Bulletin/Repair Instructions
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Service Bulletin/Repair Instructions
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Service Bulletin/Repair Instructions
Customer complaint may include engine oil leak/consumption.
71058
Service Bulletin/Repair Instructions
Warranty Bulletin D-20-18 (X86) Active Head Restraint - Select 2012-2017 Jeep Compass/Jeep Patriot (MK) and 2012 Dodge Caliber (PM) (Rev. B)
23-029-20 REV. A
Service Bulletin/Repair Instructions
Active Head Restraint (AHR) Inadvertent Deployment - X86 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.
70305
Service Bulletin/Repair Instructions
Warranty Bulletin D-20-18 (X86) Active Head Restraint - Select 2012-2017 Jeep Compass/Jeep Patriot (MK) and 2012 Dodge Caliber (PM) (Rev. A)
69919
Service Bulletin/Repair Instructions
Warranty Bulletin D-20-18 (X86) Active Head Restraint - Select 2010-2017 Jeep Compass (MK) and 2010-2012 Dodge Caliber (PM)
23-029-20
Service Bulletin/Repair Instructions
Active Head Restraint (AHR) Inadvertent Deployment - X86 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
2302920
Service Bulletin/Repair Instructions
Active Head Restraint (AHR) Inadvertent Deployment - X86 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
S1908000028 Rev.
Service Bulletin/Repair Instructions
(Rev. A) Power Inverter Load Ratings
S1908000102
Service Bulletin/Repair Instructions
(Rev. A) Power Inverter Load Ratings
9004268
Service Bulletin/Repair Instructions
THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
9004265
Service Bulletin/Repair Instructions
TRANSMISSION, 5 Speed Replacing OE transmission 05106789A$/68042789A$ with reman transmission R8142073A$ replace with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever
9004266
Service Bulletin/Repair Instructions
TRANSMISSION, 5 Speed On replacing OE transmission 05106567A$/68042567A$ with reman transmission R8142074A$ replace with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever
S1721000016
Service Bulletin/Repair Instructions
Service 4wd Light On, Message AWD System Service Required
23-015-20
Service Bulletin/Repair Instructions
Disinfectant Solution Recommended for COVID-19
08-049-20
Service Bulletin/Repair Instructions
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Service Bulletin/Repair Instructions
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Service Bulletin/Repair Instructions
Hands On Steering Wheel Message In EVIC
S1508000480
Service Bulletin/Repair Instructions
Speed Control Operates Intermittently
18-058-19 REV. B
Service Bulletin/Repair Instructions
No Start After Powertrain Control Module (PCM) Replacement and/or Reprogramming
9004022
Service Bulletin/Repair Instructions
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Service Bulletin/Repair Instructions
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Service Bulletin/Repair Instructions
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Service Bulletin/Repair Instructions
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Service Bulletin/Repair Instructions
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Service Bulletin/Repair Instructions
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Service Bulletin/Repair Instructions
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Service Bulletin/Repair Instructions
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Service Bulletin/Repair Instructions
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
Service Bulletin/Repair Instructions
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
Service Bulletin/Repair Instructions
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003220
Service Bulletin/Repair Instructions
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
T12
Service Bulletin/Repair Instructions
Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.
9003355
Service Bulletin/Repair Instructions
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
9003413
Service Bulletin/Repair Instructions
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
9003109
Service Bulletin/Repair Instructions
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Service Bulletin/Repair Instructions
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
9003694
Service Bulletin/Repair Instructions
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Service Bulletin/Repair Instructions
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Service Bulletin/Repair Instructions
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9002718
Service Bulletin/Repair Instructions
Hands Free Module - Convergence Telematics Module (CTM) Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
9003231
Service Bulletin/Repair Instructions
RHB/RBZ Radio For JK, MK, and RT ONLY: RHB/RBZ radio that supports Bluetooth and Hands- Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE
25-003-16 REV. A
Service Bulletin/Repair Instructions
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
18-048-16 REV. A
Service Bulletin/Repair Instructions
Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: P0335 - Crankshaft Position Sensor Circuit. P0456 - Evap System Small Leak. P219A - Bank 1 Air Fuel Ratio Imbalance. P050B - Cold Start Ignition Timing Performance.The following software enhancement is also available: Engine is hard to start at temperatures -29°C (-20°F) for vehicles utilizing E15 fuel only (Sales Code ECN). Cruise control acceleration rate may be considered objectionable to some customers if the accel button is held down.
2500316
Service Bulletin/Repair Instructions
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
05058172
Service Bulletin/Repair Instructions
Radiator Hose, Radiator Cap This GPOP is for two issues: 1) Part Number 05058172A. Look for folded hose at the clamped end of the hose 2) Part Number 4596198. If leak is coming from the cap, change only the cap and retest.~ For any questions about this TechTip call Sergio Santi. cell phone: (248) 613-1978 If no response in 15 minutes, please continue with repair.~
2304216
Service Bulletin/Repair Instructions
Incorrect Wheel Certification Label This bulletin involves installing new wheel rim size overlay labels. Incorrect wheel rim size printed on certification label.
05152029
Service Bulletin/Repair Instructions
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
05091960A
Service Bulletin/Repair Instructions
Hands Free Module - CTM ? Peiker Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
05091960A$
Service Bulletin/Repair Instructions
Hands Free Module - CTM ? Peiker Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
05-003-16
Service Bulletin/Repair Instructions
Low Frequency Moan Heard During First Brake Apply This bulletin involves installing an anti-vibration bracket to the rear brake caliper. A low frequency moan is heard during the first brake apply when in reverse while the vehicle is cold or has been parked for several hours. An audio sound file of the moan can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing. If the low frequency moan can be verified, the addition of the anti-vibration bracket may correct the condition.
0500316
Service Bulletin/Repair Instructions
Low Frequency Moan Heard During First Brake Apply This bulletin involves installing an anti-vibration bracket to the rear brake caliper. A low frequency moan is heard during the first brake apply when in reverse while the vehicle is cold or has been parked for several hours. An audio sound file of the moan can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing. If the low frequency moan can be verified, the addition of the anti-vibration bracket may correct the condition.
68232878A
Service Bulletin/Repair Instructions
MODULE, Totally Integrated Power (TIPM) For MK vehicles ONLY; If the customer experiences a no start due to dead battery; If the battery is dead due to radiator cooling fan stuck on (Fan runs during battery charging with key off). Before replacing the TIPM for this issue please contact Saji John at cell (248) 890-0324, or Rob Samko at cell (248) 379-4093. If response is not received within 15 minutes, continue with normal repair procedure.
68232878A$
Service Bulletin/Repair Instructions
MODULE, Totally Integrated Power (TIPM) For MK vehicles ONLY; If the customer experiences a no start due to dead battery; If the battery is dead due to radiator cooling fan stuck on (Fan runs during battery charging with key off). Before replacing the TIPM for this issue please contact Saji John at cell (248) 890- 0324, or Rob Samko at cell (248) 379-4093. If response is not received within 15 minutes, continue with normal repair procedure.
05091326A$
Service Bulletin/Repair Instructions
RHB/RBZ Radio For JK, MK, and RT ONLY: RHB/RBZ radio that supports Bluetooth and Hands- Free. For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
68018109A$
Service Bulletin/Repair Instructions
Actuator- A/C Heater Before replacing this actuator call Matt Sasina at cell (248) 464-4982. If no response in 15 minutes, continue with repair.
S18 v.2
Service Bulletin/Repair Instructions
NOTE: S18 originally published in July. Manverter changed to Maniverter. Alternate Transportation section wording revised. Customer Satisfaction Notification S18 - Engine Oil Consumption The engine on about 480 of the above vehicles may experience low oil pressure originating from an oil consumption issue. This may result in oil starvation and possible engine failure. The engine long block assembly must be replaced on the involved vehicles.
68105583A
Service Bulletin/Repair Instructions
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
RL305553A
Service Bulletin/Repair Instructions
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
S18
Service Bulletin/Repair Instructions
Customer Satisfaction Notification S18 - Engine Oil Consumption The engine on about 480 of the above vehicles may experience low oil pressure originating from an oil consumption issue. This may result in oil starvation and possible engine failure. The engine long block assembly must be replaced on the involved vehicles.
68141352A
Service Bulletin/Repair Instructions
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
0900616REVA
Service Bulletin/Repair Instructions
2.0L Or 2.4L Long Block Replacement
09-006-16
Service Bulletin/Repair Instructions
2.0L Or 2.4L Long Block Replacement This bulletin involves replacing the long block due to incorrect machining operation on the cylinder head. The customer may describe the engine is consuming oil.
0900616
Service Bulletin/Repair Instructions
2.0L Or 2.4L Long Block Replacement This bulletin involves replacing the long block due to incorrect machining operation on the cylinder head. The customer may describe the engine is consuming oil.
Z5091195A
Service Bulletin/Repair Instructions
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
Service Bulletin/Repair Instructions
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
68277402A
Service Bulletin/Repair Instructions
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
08-043-16
Service Bulletin/Repair Instructions
Flash: Wireless Control Module (WCM) Diagnostic And System Enhancements This bulletin involves updating the Wireless Control Module (WCM) with new software. A small number of customers may experience a no crank, no start or Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs): B1A25 - INVALID KEY. B1A29 - SKIM Basestation Mismatch.
0804316
Service Bulletin/Repair Instructions
This bulletin involves updating the Wireless Control Module (WCM) with new software.
18-044-16
Service Bulletin/Repair Instructions
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P0335 - Crankshaft Position Sensor Circuit. P0456 - Evap System Small Leak.** P219A - Bank 1 Air Fuel Ratio Imbalance. P050B - Cold Start Ignition Timing Performance. Other software enhancements included that will address some customers concerns: · **Cruise control acceleration rate may be considered objectionable to some customers if the accel button is held down. · Engine is hard to start at temperatures -29°C (-20°F) for vehicles utilizing E15 fuel only.**
1804416
Service Bulletin/Repair Instructions
Powertrain Diagnostic And System Enhancements.
05149171A$
Service Bulletin/Repair Instructions
Oxygen Sensor Before replacing the Upstream (1/1) O2 Sensor on a 2.4L MK due to a P0131 fault code, please contact Vijay Thiruvenkatachary at cell (906) 281-8495.~ Before replacing the Left Downstream (2/2) O2 Sensor on a 3.6L JK due to a P0157 fault code, please call Jerry Tomlin at cell (248) 202-5329. ~ Engineering would like determine whether the sensor has been contaminated with oil.~ If no response is received within 15 minutes, then continue with repair. For all other fault codes, please perform the applicable diagnostic routine.
0802916
Service Bulletin/Repair Instructions
The customer may describe that their vehicle shakes or bounces while being flat towed.
L0003157
Service Bulletin/Repair Instructions
Tail Lamp Bulb If the tail lamp bulb (L00003157) on a 2015 or 2016 MK is being replaced for any reason, engineering would like to have the bulb and the entire lamp assembly replaced and returned for analysis. If you have any questions, please contact Brigitte Wicks at cell (248) 202-9869. Also please make sure to send the part to Brigitte's attention when it is returned. Thank you.
0801416
Service Bulletin/Repair Instructions
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
RL108213A$
Service Bulletin/Repair Instructions
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
53034160A
Service Bulletin/Repair Instructions
Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
08-115-15
Service Bulletin/Repair Instructions
Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.
56046094A
Service Bulletin/Repair Instructions
Part Description: Cruise Control Switch Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair
56046094A$
Service Bulletin/Repair Instructions
Part Description: Cruise Control Switch Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair
05105572A
Service Bulletin/Repair Instructions
Part Description: Wheel Speed Sensor Issue Description: Before replacing the front wheel speed sensors, please call Gurdial Dhami at cell (226) 346-7919. If you do not receive a return call after 15 minutes, please proceed with repair.
05105572A$
Service Bulletin/Repair Instructions
Part Description: Wheel Speed Sensor Issue Description: Before replacing the front wheel speed sensors, please call Gurdial Dhami at cell (226) 346-7919. If you do not receive a return call after 15 minutes, please proceed with repair.
68166534A
Service Bulletin/Repair Instructions
Part Description: Horn and Bracket Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair.~
68166534A$
Service Bulletin/Repair Instructions
Part Description: Horn and Bracket Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair.~
21-042-15 REV-A
Service Bulletin/Repair Instructions
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience one of the following: ? Calibration will prevent unintentional engagement of AutoStick (Manual Mode) when shifter is bumped or tapped. ? Poor shift quality or a delayed shifts.
18-063-15
Service Bulletin/Repair Instructions
Flash: MIL Illumination, Cold Start and Cruise Control Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination and/or any of the following: ? Cruise Control acceleration feels to fast at low speeds (35 mph / 56 kph). ? Engine is hard to start when cold Upon further investigation, the technician may find Diagnostic Trouble Codes (DTCs): P219A - Bank 1 Air Fuel Ratio Imbalance. P050B - Cold Start Ignition Timing Performance.
SB-18-063-15
Service Bulletin/Repair Instructions
2015 JEEP COMPASS/PATRIOT: CUSTOMERS MAY COMPLAIN OF A MALFUNCTION INDICATOR LAMP ILLUMINATION. ALSO CUSTOMERS MAY EXPERIENCE CRUISE CONTROL ACCELERATION FEELS TO FAST AT LOW SPEEDS AND WHEN ITS COLD ENGINE IS HARD TO START *CN
23-035-15
Service Bulletin/Repair Instructions
Sunroof Leak Under High Water Pressure This bulletin involves installing a new sunroof service trough. The customer may describe a water leak at the rear of the sunroof when using a high pressure touchless car wash.
08-025-15
Service Bulletin/Repair Instructions
Flash: Auto Lock Feature Inoperative This bulletin involves updating the Cab Compartment Node (CCN) software. The customer may notice that the power door lock will not auto lock when the vehicle starts moving forward.
21-011-15
Service Bulletin/Repair Instructions
Transmission Fluid Overfill After Repair This bulletin involves inspecting and adjusting the transmission fluid to the correct level. A small number of customers may experience slight reduction in transmission performance after a recent repair. This may be due to an overfill condition after incorrect fill procedures being followed at the time of the repair.
2101115
Service Bulletin/Repair Instructions
Transmission Fluid Overfill After Repair This bulletin involves inspecting and adjusting the transmission fluid to the correct level. A small number of customers may experience slight reduction in transmission performance after a recent repair. This may be due to an overfill condition after incorrect fill procedures being followed at the time of the repair.
23-002-15
Service Bulletin/Repair Instructions
Key Code Missing This bulletin involves key codes that are not on file.
07-001-15
Service Bulletin/Repair Instructions
Coolant Bottle Recovery Hose Improperly Attached Check the tie strap for the coolant bottle recovery hose and replace if required. Coolant bottle recovery hose may not be properly attached.
08-112-14
Service Bulletin/Repair Instructions
Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.
0811214
Service Bulletin/Repair Instructions
Hands Free Feature Inoperative
05-003-14 REV. A
Service Bulletin/Repair Instructions
Low Frequency Moan Noise Heard During First Brake Apply This bulletin involves installing an anti-vibration bracket to the rear brake caliper. A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours.An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing.If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.
05-003-14REV.A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0500314
Service Bulletin/Repair Instructions
Low Frequency Moan Noise Heard During First Brake Apply This bulletin involves installing an anti-vibration bracket to the rear brake caliper. A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours.An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing.If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.
0500314REVA
Service Bulletin/Repair Instructions
Low Frequency Moan Noise Heard During First Brake Apply This bulletin involves installing an anti-vibration bracket to the rear brake caliper. A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours.An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing.If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.
18-070-14
Service Bulletin/Repair Instructions
Flash: MIL Illumination, P219A, P050B And Cold Start Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may see erroneous illuminated malfunction indicator lamps (MIL) and have a hard start cold condition. ? P219A Bank 1 Air Fuel Ratio Imbalance ? P050B Cold Start Ignition Timing Performance
1807014
Service Bulletin/Repair Instructions
MIL Illumination, P219A, P050B And Cold Start Improvements
23-033-14
Service Bulletin/Repair Instructions
Key Code Missing This bulletin involves reporting the key code on the vehicle repair order. The key codes were not recorded during manufacturing.
2303314
Service Bulletin/Repair Instructions
Key Code Missing
05-003-14
Service Bulletin/Repair Instructions
Low Frequency Moan Noise Heard During First Brake Apply This bulletin involves installing an anti-vibration bracket to the rear brake caliper. A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours. An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing. If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.
02-003-13
Service Bulletin/Repair Instructions
This bulletin involves centering the vehicles steering wheel. The steering wheel is off center.
9002519
Service Bulletin/Repair Instructions
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.