9100905
Service Bulletin/Repair Instructions
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
9100905
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
9100902
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S2623000001 REV.A
Rotary Shifter Lights Blinking, Shifter Not Moving, Not Going Into Gear.
S2523000032 REV.B
Steering Dragging While Recreational Flat Towing Behind RV.
113528
SHAFT - AXLE HALF
113529
SHAFT - AXLE HALF
9100866
Display Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.
08-274-26
Power Folding Seat Wire Harness Pinched Customers may experience one or more of the following: SYMPTOM: ● Battery is depleted. NOTE: Battery depletion may be due to a pinched power folding seat wire harness behind the left quarter panel by the cargo tie down fastener. ● Loss of function of the rear folding seats. ● Rear folding seat behavior is not functioning as expected. This bulletin involves repairing a pinched power folding seat wire harness behind the left quarter panel.
9100859
Before replacing any part, check the DOT on the glass or the PN to make sure you choose the replacement part from the correct supplier: DOT 615 - 6NC10TRMAH - CIE Supplier DOT 1038 - 6NC07TRMAR - CIE Supplier DOT 1065 - 7TF32TRMAB, 7TF33TRMAB - HCMF Supplier
9100833 REV1
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
112639
THROTTLE BODY – NONE
112640
THROTTLE BODY – NONE
113123
SPRING KIT - DISC BRAKE PAD
9100811 Rev 4
Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
S2102000004 REV.D
WL Front Control Arm Bushing - Handling Link Has Loose Rubber Appearance
112979
CAMERA - REAR VIEW
112980
CAMERA - REAR VIEW
S2623000041 REV.A
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed. Rev A
112842
BOLT - HEX FLANGE HEAD
9100833
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S268A000014
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
112856
HEATER - ELECTRIC COOLANT
112857
HEATER - ELECTRIC COOLANT
S1623000028 Rev. K
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2608000028
Intermittent Operation of the Third Row Power Seat, 12volt Battery Drain
S2503000001 REV.A
Service 4WD Message, With Any Combination Of The Following Front Axle Disconnect (FAD) Diagnostic Trouble Codes
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S1623000028 REV.J
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
S2623000041
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed.
08-221-26 REV. A
R1H Radio U41.10 USB Software Update Customers may experience one or more of the following: ● FCW OFF light ON with no DTCs and can't turn off. ● Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera Functions Normally). ● Paddle shifters not working/no longer a setting. ● Autolocks not working. ● Auto headlights not working. ● AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). ● Album Art flickering issue. ● Blank screen and then reboot every 2 minutes and 40 seconds. ● CarPlay icon disappears from main screen while still active, leaving no navigation path back. ● Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after FOTA. ● Valet mode sends duplicate requests causing HU and vehicle state misalignment. ● Rear seat media page intermittently shows a blank screen. ● Unable to select or drag 'Pitch and Roll' widget on home screen. ● USB playback resumes incorrectly, skipping to next track after reconnect. ● Album art not displayed on HMI despite availability in media. ● Incorrect call timer displayed for conference calls. ● Call status remains 'active' on widget after call ends. ● Second call status not updated on home screen widget. ● Rear entertainment tab intermittently blank when switching apps. ● System crashes for 20 to 30 seconds after voice reply action. ● Media progress bar continues incorrectly after second call acceptance. ● CarPlay device fails to reconnect automatically or manually. ● Rear HVAC lock/unlock text missing while icon is present. ● Visual glitch observed on Front Passenger Display Module (FPDM) display. ● Surround view camera accessible while driving across apps (unexpected behavior). ● IPC navigation map fails to load despite radio showing navigation. ● Head Up Display (HUD) layout resets after overnight sleep cycle. ● ParkSense triggers unintended surround camera activation. ● HUD settings not retained after ignition cycle. ● Audio focus stuck on VR; selected message not read. ● Preset bar appears blank after overnight sleep cycle. ● FM channel switches unexpectedly and reverts after delay. ● Massage activation causes HU black screen/media disruption. ● Non-applicable ambient lighting setting visible in vehicle menu. ● Navigation screen appears black after system startup. ● Track name flickers on status bar during CarPlay playback. ● HU toggles between Home and Media screens without user input. ● Phantom touch causes navigation to switch from full screen to split view. ● HU redirects to CarPlay tab when exiting camera unexpectedly. ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (Rearview Camera Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (Rearview Camera Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (Rearview Camera Functions Normally). ● Ghost touch on Navigation screen (Rearview Camera Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after view camera event selected by customer in the Camera View Pages (Rearview Camera Functions Normally). This bulletin involves inspecting and if required, updating the radio software level to U41.10. Depending on the radio's current software level the radio may need a one or two USB update.
OTHERDOC_164
Radio Over The Air Update to U41.10 R1H Software Version (FOTA) Customers may experience one or more of the following: Inaccurate status or information displayed during phone calls- Voice Recognition performance- Carplay connectivity issues- Black / blank screens for Navigation or Media apps not affecting rearview camera funtionality- Visual glitch on Front passenger Display- Unresponsive widgets- Light & Dark mode discrepancy between screen views- Unresponsive hard button to turn screen off- Incomplete or innacurate pop-up notifications- Radio stuck in Valet Mode- Phantom / Ghost touch on Media screens- Incorrect menu displayed
9100826
WL DDM/PDM Mirror Blindspot inoperative If DTC is present DTC B285F-15 Blind Spot Warning Light Control-Circuit Short to Battery or Open Before replacing DDM/PDM. Inspect connection on Mirror connector end. Perform electrical continuity test. After succesful continuity test. Via Witech perform hard reset and clear DTC.
S1623000028 REV.I
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
9100811Rev3
***68375577A$ is not showing the correct verbiage please update and correct*** Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
23-019-26
Hot Cup Holders Customers may comment on the following: ● When the rear heat temperature is set at or near max hot output, the front center console's surfaces, first row and second row cup holders and storage bins are getting warm to the touch. This bulletin involves removing the front center console and installing an insulator foam pad on top of the Center Console air duct.
08-221-26
R1H Radio U41.10 USB Software Update Customers may experience one or more of the following: ● **FCW OFF light ON with no DTCs and can't turn off. ● Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera (RVC) Functions Normally). ● Paddle shifters not working/No longer a setting. ● Autolocks not working. ● Auto headlights not working. ● AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). ● Album Art flickering issue. ● Blank screen and then reboot every 2 minutes and 40 seconds. ● CarPlay icon disappears from main screen while still active, leaving no navigation path back. ● Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after FOTA. ● Valet mode sends duplicate requests causing HU and vehicle state misalignment. ● Rear seat media page intermittently shows a blank screen. ● Unable to select or drag 'Pitch and Roll' widget on home screen. ● USB playback resumes incorrectly, skipping to next track after reconnect. ● Album art not displayed on HMI despite availability in media. ● Incorrect call timer displayed for conference calls. ● Call status remains 'active' on widget after call ends. ● Second call status not updated on home screen widget. ● Rear entertainment tab intermittently blank when switching apps. ● System crashes for 20 to 30 seconds after voice reply action. ● Media progress bar continues incorrectly after second call acceptance. ● CarPlay device fails to reconnect automatically or manually. ● Rear HVAC lock/unlock text missing while icon is present. ● Visual glitch observed on FPDM display. ● Surround view camera accessible while driving across apps (unexpected behavior). ● IPC navigation map fails to load despite HU showing navigation. ● HUD layout resets after overnight sleep cycle. ● ParkSense triggers unintended surround camera activation. ● HUD settings not retained after ignition cycle. ● Audio focus stuck on VR; selected message not read. ● Preset bar appears blank after overnight sleep cycle. ● FM channel switches unexpectedly and reverts after delay. ● Massage activation causes HU black screen/media disruption. ● Non-applicable ambient lighting setting visible in vehicle menu. ● Navigation screen appears black after system startup. ● Track name flickers on status bar during CarPlay playback. ● HU toggles between Home and Media screens without user input. ● Phantom touch causes navigation to switch from full screen to split view. ● HU redirects to CarPlay tab when exiting camera unexpectedly.** ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally) This bulletin involves inspecting and if required, updating the radio software level to **U41.10.** Depending on the radio's current software level the radio may need a one or two USB update.
9100811 REV1
Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
S2123000070 REV.A
After Electric Power Steering (EPS) Replacement, Diagnostic Trouble Code (DTC) C221C-00 ECU Not Programmed/Flash Required Is Set
9100532 REV1
Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, Electronic Stability Control (ESC) light on, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced. Note: WL / WS SCCMs do not contain a Steering Angle Sensor (SAS) The Steering Angle is computed within the Electronic Power Steering (EPS) module. See Electronic Power Steering (EPS) module for diagnosis and repair procedures.
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
9100811
Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the tension link. This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
S248A000015 REV.A
Poor Audio Quality And Or Static From Wireless Devices
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
111702
SWITCH - LIFTGATE
111619
ACTUATOR - A/C AND HEATER
111620
ACTUATOR - A/C AND HEATER
S2102000004 REV.C
WL Front Control Arm Bushing - Handling Link Has Loose
S2523000003 REV.A
Door Latch, Handle And Ajar Additional Service Information.
18-050-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0300 - Multiple Cylinder Misfire - In Active or Stored status set during cold start catalyst heating. ● P0301 - Cylinder 1 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0302 - Cylinder 2 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0303 - Cylinder 3 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0304 - Cylinder 4 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0305 - Cylinder 5 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0306 - Cylinder 6 Misfire - In Active or Stored status set during cold start catalyst heating. Customers may also comment on one or more of the following: ● Check engine illuminates when fueling the vehicle while the engine is running. ● Vehicle has a noticeable misfire. ● Vehicle idles rough. ● Engine noise. NOTE: Noise is heard coming from the valvetrain. In addition, the following software enhancement is available: ● Update to prevent customers from driving their vehicles while the Electric Park Brake (EPB) is engaged. Engine torque will be limited to prevent the Rear Drive Unit from being damaged. NOTE: Previously, the EPB would remain engaged without any torque limit which could lead to the Rear Drive Unit being damaged/broken. This bulletin involves reprogramming the PCM with the latest available software.
08-075-26 REV. A
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S2623000024
U0422-00 Implausible Data From BCM Set In Central ADAS Decision Module (CADM).
S2623000022
Buzz Squeak Rattle (BSR) Noise From Rear Of Vehicle.
S1623000028 REV.H
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2223000022 REV.E
Power Liftgate Inoperative Or Intermittently Will Not Open Or Close.
111118
COVER - CARGO AREA
S2602000003
Clunk, Creaking, Squeaking, Knocking Noise From Front Suspension Over Bumps And Or Rough Road Conditions.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2608000015
Memory Seat Does Not Work There Is No Response from The Seat While Pressing the Memory Seat Profiles from the Switch Diagnostic Trouble Code (DTC) B1D9B-54- Seat Horizontal Front Stop Not Learned-Missing Calibration
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
110592
SENSOR - PINCH
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
110608
SPEAKER - NONE
9100761 Rev 1
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
110447
WATER PUMP
110448
WATER PUMP
08-075-26
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S228A000025 REV.A
Harman R1H Uconnect 5 Radio Software Flash Error Codes
S2623000007
The Handsfree Kick Feature Does Not Work Or Works Intermittently.
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
109003
HOSE - SUNROOF DRAIN
9100761
Open a star case prior to ordering or installing a replacement 68436288A$ or Z8436288A$ PN This includes AM, AJ or AK level. AM level is not available to order at this time. AJ or AK level is recommended to verify proper connected services at this time.
9100755
Any 2021-2022MY WL that has the right power liftgate anti-pinch sensor or power liftgate module(PLGM) replaced, both components need to be replaced as a pair.
S2523000089 REV.A
Passive Entry Exterior Door Handle Inoperative When Touched For Lock And Or Unlock.
08-014-26
Not applicable to vehicles built for US market. R1H Radio U40.20 USB Software Update - Korea Customers may experience one or more of the following: ● T-maps navigation feature is intermittently not available due to map loading. ● When the navigation speed alarm margin is set and the while driving the vehicle between the speed limit and the set margin, the navigation speed alarm will sound off continuously and the user is unable to control the volume. ● After setting a navigation destination and then the customer is following the navigation route, the navigation system will stop operating. ● Navigation touch screen menu is inoperable after setting a navigation destination. The home screen widget will be black and the navigation display map will no longer show the navigation route. ● WI-FI software update pop up is being triggered in non connected vehicles. ● Vehicle Forward Collision Warning must have two options: OFF / Warning + Active Braking. ● Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects Right Hand Drive RHD only. ● With ignition on and radio on, the radio display freezes then restarts (Rearview Camera (RVC) functions normally). ● Radio is taking more than one minute to start after starting the engine (RVC functions normally). ● System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode (RVC functions normally). This bulletin involves inspecting and if required, updating the radio software level to U40.20. Depending on the radio's current software level the radio may need a one or two USB update. M08 FSAR-RSU-6722 -2-
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
S2521000004 REV.B
The customer is experiencing a clicking or pop noise from the steering knuckle and bearing area during turns while driving.
9100753
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.
S2623000001
Rotary Shifter Lights Blinking, Shifter Not Moving, Not Going Into Gear.
S2623000002
Service Shifter Message On Instrument Cluster With Loss Of Communication Diagnostic Trouble Code (DTC) Related To The Shifter.
109231
LATCH - LIFTGATE
109232
LATCH - LIFTGATE
S2521000004 Rev.A
Note: actual release date was 12/22/2025 The customer is experiencing a clicking or pop noise from the steering knuckle and bearing area during turns while driving.
109161
SWITCH - TRANSFER CASE, RIDE HEIGHT, TERRAIN SELECT
109157
ARMREST - REAR DOOR TRIM
S2521000005
The customer states the ABS and Traction Control warning comes on. Vehicle sets wheel speed BSCM/ABS fault codes.
S2523000094
Power Liftgate Noise During Gate Operation
108974
THROTTLE BODY - NONE
108941
MODULE - STEERING CONTROL
108942
MODULE - STEERING CONTROL
S2521000006
Service 4WD light on in the cluster. C14A1-74 DTC will be present (Active or Stored).
108833
AMPLIFIER - NONE
S258A000021
Diagnostic Trouble Code (DTC) B15A1-00 Media Port Connection 1 Connection Found Set.
S2423000012 REV.D
Power Liftgate Is Inoperative or Won’t Close.
S2523000089
Passive Entry Exterior Door Handle Inoperative When Touched For Lock And Or Unlock.
S2523000065 REV.A
Diagnostic Trouble Code DTC(s) C1593-00, C2217-00, U0131-00. and Service Electric Power Steering Messages.
S2521000004
The customer is experiencing a "clicking" noise during turns while driving on WL vehicles
S2509000009
Engine Oil Leak
105646
MODULE - STEERING CONTROL & COLUMN
S2522000003
Tire Pressure Monitor (TPM) Warning Lamp On Or Flashing. Sensor(s) Not Reading And Or Showing Dashes.
08-310-25
R1H Radio U33.43 USB Software Update Customers may experience one or more of the following: ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally) This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio's current software level the radio may need a one or two USB update
08-302-25 REV. A
Not applicable to vehicles built for US market. Radio USB Update to U40.20 Customers may experience one or more of the following: ● Temperature displayed in the radio display screen and rear HVAC are mismatched. ● Auto door locks are inoperable. This bulletin involves inspecting and if required, updating the radio software level to U40.20. Depending on the radio’s current software level the radio may need a one or two USB update.
08-237-25 REV. A
Not applicable to vehicles built for US market. R1H Radio U40.20 USB Software Update Customers may experience one or more of the following: ● **Temperature displayed in the radio display and rear HVAC are mismatched.** ● Wi-fi Software update pop-up is being triggered in non connected vehicles. ● Radio freezes and then restarts. ● Head Unit (HU) freezes and then restarts. ● HU is taking more than one minute to start after starting the engine. ● System displays blank screen in E-Hybrid tab when user switched to dark theme mode. Rearview Camera (RVC) functions normally. This bulletin involves inspecting and if required, updating the radio software level to **U40.20**. Depending on the radio’s current software level the radio may need a one or two step USB update
08-266-25 REV. A
Not applicable to vehicles built for US market. R1H Radio U40.20 USB Software Update - Korea Customers may experience one or more of the following: ● **T-maps navigation feature is intermittently not available due to map loading. ● When the navigation speed alarm margin is set and the while driving the vehicle between the speed limit and the set margin, the navigation speed alarm will sound off continuously and the user is unable to control the volume. ● After setting a navigation destination and then the customer is following the navigation route, the navigation system will stop operating. ● Navigation touch screen menu is inoperable after setting a navigation destination. The home screen widget will be black and the navigation display map will no longer show the navigation route.** ● WI-FI Software update pop up is being triggered in non connected vehicles. ● Vehicle Forward Collision Warning must have two options: OFF/ Warning + Active Braking. ● Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects RHD only. ● With key on and radio on, The radio display freezes then restarts (Rearview Camera (RVC) functions normally). ● Radio is taking more than one minute to start after starting the engine (RVC functions normally). ● System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode (RVC functions normally). This bulletin involves inspecting and if required, updating the radio software level to **U40.20**. Depending on the radio's current software level the radio may need a one or two USB update
08-313-25
Flash: Amplifier (AMP) Diagnostic and System Updates Customers may experience one or more of the following: ● **Droning noises coming out of the speakers at specific RPMs that range from 1200 to 1800 RPM. Probability of occurence is most likely during cold ambient temperatures.** ● High pitched noise at start up or idle under cold conditions. This bulletin involves updating the AMP with the latest available software.
S2519000008 REV.A
Noise From Front End While Steering Or Turning The Steering Wheel.
S2523000079
Rear Door Mounted Window Switch Button Is Inoperative, Stuck, Or Switch Button Does Not Return To Original Position After Pushed.
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
9100671
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
106345
SHAFT - STEERING COLUMN INTERMEDIATE
106346
SHAFT - STEERING COLUMN INTERMEDIATE
106357
CENTER STACK - DISPLAY
08-266-25
Not applicable to vehicles built for US market. R1H Radio U33.43 USB Software Update Customers may comment on one or more of the following: ● WI-FI Software update pop up is being triggered in non connected vehicles. ● Vehicle Forward Collision Warning must have two options: OFF/ Warning + Active Braking. ● Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects RHD only. ● With key on and radio on, The radio display freezes then restarts. ● Radio is taking more than one minute to start after starting the engine. ● System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio’s current software level the radio may need a one or two step USB update
S2223000074 REV.B
Power Side Steps Reverse, Stop In Motion, Do Not Deploy Or Stow, And May Have a Chirp Noise.
S2408000079 REV.A
Liftgate Lock Button Inoperative, Cluster Message “Service Keyless System”
08-237-25
Not applicable to vehicles built for US market. R1H Radio U33.43 USB Software Update Customers may experience one or more of the following: ● Wi-fi Software update pop-up is being triggered in non connected vehicles. ● Radio freezes and then restarts. ● Head Unit (HU) freezes and then restarts. ● HU is taking more than one minute to start after starting the engine. ● System displays blank screen in E-Hybrid tab when user switched to dark theme mode. This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio’s current software level the radio may need a one or two step USB update.
S2108000236 REV.B
Windshield HUD (Head Up Display) Display Features
S258A000017
Door speaker Inoperative or No Sound
S2509000001 REV.B
Engine Rattle Noise
S258A000002 REV.A
Radio Screen Goes Blank, Rearview Camera (RVC) Functions Normally
106320
Warranty Newsletter – Volume 11, Issue 7
106321
FCA Caribbean Warranty Newsletter – Volume 11, Issue 7
S2422000001 REV.D
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
08-220-25
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S2523000061 REV.A
Blind Spot Mirror Warning Inoperative Or Intermittently Inoperative. Service Blind Spot Message In Cluster.
09-018-25
Engine Cylinder Block Porosity Inspection - Engine Cold Start Rough Idle Customers may experience the following: ● Rough engine idle when cold starting the engine. ● Low coolant level in coolant recovery bottle.
105648
MODULE - ENGINE CONTROLLER
S2519000006
Steering Repair Information Involving Toe Angle. Tie Rod And Or Electric Power Steering (EPS) Units.
21-009-25 REV. C
850RE D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2219000005 REV.D
Check Engine Lamp On. Warning Messages in the Cluster. U0131 Lost Communication with Power Steering Control Module Set.
S2523000065
Diagnostic Trouble Code DTC(s) C1593-00, C2217-00, U0131-00. and Service Electric Power Steering Messages.
S2523000061
Blind Spot Mirror Warning Inoperative Or Intermittently Inoperative. Service Blind Spot Message In Cluster.
9100614
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
105590
Warranty Newsletter – Volume 11, Issue 6
105591
FCA Caribbean Warranty Newsletter – Volume 11, Issue 6
S2523000054
Intermittent Vibration Buzz Squeak Rattle (BSR) Shaking Felt In Steering Wheel.
08-179-25
12 Channel Amplifier Popping Noise Sound Customers may experience the following: ● Popping sound coming from the speakers during engine start/run. This bulletin involves replacing the Audio Amplifier.
S2519000004
Steering Wheel Off Center. Customer Complaint/Technician Observation: Customer may state the vehicle drives straight but the steering wheel is off center. They may also describe the condition as a pull or a lead due to them trying to keep the steering wheel centered. Discussion: Drive on both highway and city roads if possible. If equipped with air suspension, place the vehicle in normal ride height (NRH). Refer to Service Library 02 - Front Suspension / Wheel Alignment / Diagnosis and Testing for a list of conditions, possible causes and corrections.
S2519000004REVA
Steering Wheel Off Center. Customer Complaint/Technician Observation: Customer may state the vehicle drives straight but the steering wheel is off center. They may also describe the condition as a pull or a lead due to them trying to keep the steering wheel centered. Discussion: Drive on both highway and city roads if possible. If equipped with air suspension, place the vehicle in normal ride height (NRH). Refer to Service Library 02 - Front Suspension / Wheel Alignment / Diagnosis and Testing for a list of conditions, possible causes and corrections.
9100594
Front Door Interior Panels: Warped Interior Door Panel / Broken Panel / Door Panel Not Fully Seated Observation: Would observe that the interior door panel is not properly seated or attached. Panel(s) may appear warped or out of position in some areas. No signs of damage should be expected. How to diagnose: Visually inspect the door panel(s) for proper installation and check for the presence of broken or loose clips. Remove the panel and inspect clips and clip towers. Next step would be reinstalling the panel if visual inspection does not find any issues. Repair Procedure: Require a picture of the door panel(s) in the 'as found' condition so we can understand what warped means in the claims that are being created. After, check the door panel for proper installation and for the presence of broken or loose clips. Remove the panel, following normal servicing procedure, and inspect clips and clip towers. If any clips are broken or missing, replace prior to reinstalling original door. After confirmation that no loose/broken/damaged clips and/or clip towers, and reinstalling door panels does not correct issue, then a 'front door trim panel' kit / claim would be acceptable. In this case, Stellantis would like to request the panel back. How to validate fix: Verify that door has no loose/broken/damaged clips and/or clip towers. Replace any broken/missing clips where possible. Then validate that reinstalling the interior door panel addresses initial issue made within the claim.
9100595
Front Door Interior Panels: Warped Interior Door Panel / Broken Panel / Door Panel Not Fully Seated Observation: Would observe that the interior door panel is not properly seated or attached. Panel(s) may appear warped or out of position in some areas. No signs of damage should be expected. How to diagnose: Visually inspect the door panel(s) for proper installation and check for the presence of broken or loose clips. Remove the panel and inspect clips and clip towers. Next step would be reinstalling the panel if visual inspection does not find any issues. Repair Procedure: Require a picture of the door panel(s) in the 'as found' condition so we can understand what warped means in the claims that are being created. After, check the door panel for proper installation and for the presence of broken or loose clips. Remove the panel, following normal servicing procedure, and inspect clips and clip towers. If any clips are broken or missing, replace prior to reinstalling original door. After confirmation that no loose/broken/damaged clips and/or clip towers, and reinstalling door panels does not correct issue, then a 'front door trim panel' kit / claim would be acceptable. In this case, Stellantis would like to request the panel back. How to validate fix: Verify that door has no loose/broken/damaged clips and/or clip towers. Replace any broken/missing clips where possible. Then validate that reinstalling the interior door panel addresses initial issue made within the claim.
02-002-25
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
09-011-25
Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise.
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
S2519000003
Slight Pull, Drift, Wander. Lack Of Precise Steering.
104686
BOLT - HEX FLANGE HEAD
08-105-25 REV. A
Flash: Trailer Tow Module (TTM) Updates Customers may comment on one or more of the following: ● If the vehicle is traveling at less than 5 kph (3 mph) and the brake pedal is pressed, then both turn lights will flash for two milliseconds. ● If the vehicle is traveling at less than 5 kph (3 mph) and one turn light is activated, then the opposite turn light will flash for 20 milliseconds. NOTE: This issue only effects the trailer lighting This bulletin involves updating the TTM with the latest available software.
9100498 Rev 3
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
9100534 Rev 1
Transmission "Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
9100570
Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible "glitter" or debris in the pan does not justify complete unit replacements.
S2523000046
Check Engine Lamp On. Diagnostic Trouble Code (DTC) P1D73 And Or P05AE For Active Grill Shutter (AGS).
104683
CARPET - REAR FLOOR
S2523000040
Center Console Armrest Lid Does Not Stay Open, Feels Loose, Does Not Latch.
S2523000036
Sunroof Inoperative, Not Moving To Open Or Closed Positions.
S2108000241 REV.B
No Crank, No Start, Start Stop Inoperative
S2523000034
C008E-00 Setting After Windshield Replacement
104558
FCA Caribbean Warranty Newsletter – Volume 11, Issue 4
104557
Warranty Newsletter – Volume 11, Issue 4
08-105-25
Flash: Trailer Tow Module(TTM) Updates Customers may comment on one or more of the following: ● If the vehicle is traveling at less than 5 kph (3 mph) and the brake pedal is pressed, then both turn lights will flash for two milliseconds. ● If the vehicle is traveling at less than 5 kph (3 mph) and one turn light is activated, then the opposite turn light will flash for 20 milliseconds This bulletin involves updating the TTM with the latest available software.
21-009-25 REV. B
850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2523000023
Trailer Tow Lights Inoperative. Diagnostic Trouble Codes (DTCs) B166E-13 B17AD-13 May Be Set.
S2523000010 REV.A
Exterior Rear View Mirror Stained And Will Not Clean.
S2509000001 REV.A
Engine Rattle Noise
S258A000011
Crackle, Pop or Growl noise At Start-up
9100534
Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback.
9100532
MODULE Steering Control Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced.
103953
VALVE - OIL CONTROL
9100390 Rev 1
D Clutch Repair Kit For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback.
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
08-063-25
Radio USB update to U33.43 Customers may experience one or more of the following: ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally). REPAIR SUMMARY: This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio’s current software level the radio may need a one or two USB update.
9100502
LOWER ACTIVE GRILL SHUTTER If the upper or lower AGS seems to be inop please make sure you CLEAR the DTCs BEFORE swapping the old AGS for a new one, and test if the error code returns. Very often the wiring harness presents corrosion, so make sure to check it for any damage BEFORE swapping the AGS. Corrosion in the harness disrupts communication with the AGS, which sets up the DTCs for AGS performance and lights the CEL. If the AGS is inop and it will be replaced and sent back to Stellantis also send back the wiring harness with it. Make sure to fully perform the PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE as indicated in the service library.
S2509000002
Engine Noise
S258A000009
Apple CarPlay Does Not Complete The First Initial Wireless Connection.
S2123000084 REV.A
1st Row Seat Belt Retractor D-Ring Is Binding And Not Able To Rotate
S2423000008 REV.A
SOS Button Inoperative And Or Unavailable. B1552-2A Code Set.
S2423000034 REV.A
Defroster Grille Has Gaps And Or Is Not Sitting Flush.
S2513000001
Grille molding applique is sticking out at the headlamp
S2523000016
Replacement Exterior Mirror Glass Connector Does Not Match For Blind Spot.
9100498 REV 1
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
S2108000015 REV.J
Uconnect Box Require Service Message
S2523000011
Exterior Mirror Blind Spot LED Indicator Inoperative Or Will Not Turn Off. Diagnostic Trouble Code (DTC) B285F-11 And Or B285F-15 Set.
9100500
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
S2223000074 REV.A
Exterior Power Fold Mirror Does Not Travel To Full Extend or Fold Positions.
S2523000010
Exterior Rear View Mirror Stained And Will Not Clean.
S2509000001
Engine Rattle Noise
23-008-25
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S2219000005 REV.C
Check Engine Lamp On. Warning Messages In The Cluster. U0131 Lost Communication With Power Steering Control Module Set.
S228A000005 REV.E
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
9100498
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets).
S2503000001
Service 4WD Message, Diagnostic Trouble Codes (DTCs) C1463-94 Front Axle Disconnect Control-Unexpected Operation, and/or C1463-92 Front Axle Disconnect-Performance or Incorrect Operation, Set.
S2503000002
Service 4WD Message Illuminated. Diagnostic Trouble Code (DTC) C1477-98 Transfer Case Clutch Component Or System Over Temperature, Set.
102939
LATCH – FRONT & REAR DOOR
21-009-25 REV.A
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch
102934
THROTTLE BODY
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
102811
TRANSMISSION - 8 SPEED
S2523000006
Buzz Squeak Rattle (BSR) Noise At Idle.
21-009-25
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
S2523000003
Door Latch, Handle And Ajar Additional Service Information.
21-039-24 REV. H
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.