114537
Service Bulletin/Repair Instructions
EVAPORATOR - AIR CONDITIONING
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
114537
EVAPORATOR - AIR CONDITIONING
114538
EVAPORATOR - AIR CONDITIONING
9100897Rev1
Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Reservoir 68087240AA Temperature Sensor 68041137AF Compressor Assembly Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
9100897
Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Temperature Sensor 68041137AF Service Components Reference Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
9100833 REV1
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
112639
THROTTLE BODY – NONE
112640
THROTTLE BODY – NONE
S2208000045 REV.D
Backup Camera Poor Image Quality Inspection
112857
HEATER - ELECTRIC COOLANT
S1623000028 Rev. K
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S1623000028 REV.J
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S1623000028 REV.I
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000023
Power Liftgate Inoperative.
S1623000028 REV.H
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2208000045 REV.C
Backup Camera Poor Image Quality Inspection
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
110447
WATER PUMP
110448
WATER PUMP
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
109231
LATCH - LIFTGATE
109232
LATCH - LIFTGATE
08-396-25
Drivetrain Control Module (DTCM) Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C1403 - 92 Transfer Case Range Position Sensor - Performance Or Incorrect Operation. ● U0403 - 00 Implausible Data Received From Transfer Case. Customers may experience the following: ● Service 4WD Light On in Instrument Panel Control (IPC) This bulletin involves replacing the DTCM.Drivetrain Control Module (DTCM) Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C1403 - 92 Transfer Case Range Position Sensor - Performance Or Incorrect Operation. ● U0403 - 00 Implausible Data Received From Transfer Case. Customers may experience the following: ● Service 4WD Light On in Instrument Panel Control (IPC) This bulletin involves replacing the DTCM.
108974
THROTTLE BODY - NONE
108546
ISOLATOR - ENGINE MOUNT
108840
Hose- Oil Cooler Inlet, Outlet
108547
ISOLATOR - ENGINE MOUNT
S2509000009
Engine Oil Leak
105646
MODULE - STEERING CONTROL & COLUMN
9100670
Data collection required for all 2020-2026MY vehicles with 3.6L PSU engines during any of their first 3 engine oil changes. This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.
9100671
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
9100645
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
9100639
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
S258A000017
Door speaker Inoperative or No Sound
S2509000001 REV.B
Engine Rattle Noise
9100627
To inform dealers about the 850RE valve body PN: R8348504A connector: the original 16-pin connector included six pins that were not used in this application. To simplify the design, the connector has been optimized and updated to a 10-pin configuration.
21-009-25 REV. C
850RE D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100622
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
9100618
Display Verify Z part number availability. Order a Z part number for all Exchange Orders: Warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only.
9100614
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
09-015-25
Spark Knock/Engine Symptoms Customers may experience the following: ● Knocking or pinging noise coming from the engine upon acceleration. This bulletin involves cleaning the piston heads and cylinder head combustion chambers to resolve a spark knock condition being caused by oil intrusion through the PCV system.
105590
Warranty Newsletter – Volume 11, Issue 6
105591
FCA Caribbean Warranty Newsletter – Volume 11, Issue 6
02-002-25
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
09-011-25
Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise.
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
105038
TUBE - FUEL INJECTOR SUPPLY & GASKET - NONE
105039
TUBE - FUEL INJECTOR SUPPLY & GASKET - NONE
9100498 Rev 3
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
9100534 Rev 1
Transmission "Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
9100570
Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible "glitter" or debris in the pan does not justify complete unit replacements.
9100546
Display Verify Z part number availability. Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only.
21-009-25 REV. B
850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2509000004
Misfire DTCs, Rough Idle, Valvetrain Noise
S2509000001 REV.A
Engine Rattle Noise
9100534
Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback.
103953
VALVE - OIL CONTROL
9100390 Rev 1
D Clutch Repair Kit For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback.
S2509000002
Engine Noise
9100498 REV 1
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
9100500
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
102812
RAIL - FUEL
9100498
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets).
21-009-25 REV.A
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch
102934
THROTTLE BODY
9100494
FUEL PUMP/LEVEL UNIT MODULE For vehicles with Saddle Fuel Tanks, need to determine if there are any DTCs in wiTECH. Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
102811
TRANSMISSION - 8 SPEED
21-009-25
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
21-039-24 REV. H
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch
S2208000045 REV.B
Backup Camera Poor Image Quality Inspection
9100448
HEADREST Incoming Vehicles with Deployed Active Head Rest (AHR) should have a through enquiry. If there is no Broken Pieces or Electrical failure, Direction to follow the RESET Procedure in service Library to RESET the AHR
21-039-24 REV. G
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
101232
Plate - Planetary
21-039-24 REV. F
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
21-039-24 REV. E
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
21-039-24 REV. D
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
21-039-24 REV. C
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
100164
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
21-039-24 REV. B
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
99500
CARRIER – PLANETARY & SHAFT KIT - OUTPUT
S2421000001
No Reverse And/Or Forward Gear After D-Clutch Repair.
9100390
D Clutch Repair Kit TSB 21-039-24 REV A - D-Clutch repair kit missing Carrier Output Shaft Seals It has been identified the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.
98931
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
98933
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
21-039-24 REV. A
D Clutch Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
S2307000002 REV.B
Suspected Engine Coolant Leak
21-039-24
D Clutch Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
9100338REV1
GENERATOR Engine Prior to alternator/generator removal: 1. Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section "System Operation - Smart Charging System". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC.
S1908000050 REV.A
Checking Radio Software Level On A VP2 Radio
9100344
VALVE BODY & CONTROL UNIT Transmission Ensure clutch pressure check has been completed and documented prior to valve body replacement.
S2307000002 REV.A
Suspected Engine Coolant Leak
9100337
PUMP WATER For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
S248A000001
SOS and Assistance Call Not Working After Radio Exchange Unit Installed
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100276
Spring Front Upr - Isolator Before replacing this part. Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.
S2309000013
Verifying Camshaft Diagnosis
0901923
Cold Engine Ticking Noise From Exhaust Manifold Area The customer may describe an ticking noise from the exhaust manifold location(s) when cold. This bulletin involves replacing the exhaust manifolds.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
S2221000003
8-Speed Transmission, Additional Transmission Fluid Leak Inspection/Repair Guidelines.
9100212
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
S2108000138
Steering Column Power Tilt Inoperative
S2307000002
Suspected engine coolant leak.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
S2008000031
Low Charging Voltage Displayed On Cluster
S2108000093
Apple CarPlay Does Not Work Or Not Connecting
S1808000152
CEL (Check Engine Lamp) Illuminated, P057B Brake Pedal Position Sensor Performance
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
ZD7
Customer Satisfaction Notification ZD7 - Radio Software update
1400523
Fuel Nozzle Premature Shut Off The customer may experience the following: ? Hard to fill fuel tank, premature fuel nozzle shut off. This bulletin involves inspecting and replacing the fuel filler tube
ReferenceZD7
Customer Satisfaction Notification ZD7 - Radio Software Update
0814023
Radio Over The Air JR34.41F Updating to JR34.42F Software Version ? Mobile WiFi inoperative upon start up. ? WiFi hotspot gives ?No Internet? connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.41F to JR34.42F. NOTE: The National campaign for this FOTA update launched July 5, 2023.
BulletinA
Customer Satisfaction Notification ZD7 - Radio Software Update
S2309000002
MIL lamp-on. Engine noise, rattle. Misfire or rough running.
0700723
Water Quality When Mixed With Engine Coolant
S238A000024
SOS, Assistance Calls Not Successful After Radio Replacement or Radio Software Update
9100142
Mirror
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
0809423
Flash: Radio Frequency Hub Module (RFHM) Updates The customer may describe that they heard about these vehicles that can be unlawfully driven away by thieves when they are able to program new key fobs through the RFHM. Software enhancement include: ? Update to the RFHM software to prevent hackers from programming their own key fob to the vehicle. ? This is intended to deter an unwanted drive off of the vehicle without the customers knowledge.
S2307000001
Customer complaint may include a coolant leak, or, a coolant leak is detected during a routine oil change inspection.
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S228A000028
Radio Remained On After Ignition Is Switched Off, Dead Battery From Excessive Radio Current Draw
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
0804523
Radio Over The Air Updating to 34.42 Software Version ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
08-038-23
Radio Over The Air JR34.3 Updating to JR34.32.Software Version Customers may experience one or more of the following: Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.
08-022-23
Radio Over The Air Updating to 40.12 Software Version Mobile Wi-Fi inoperative upon start up. Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.
S2323000002
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
0821422
Radio Over The Air Updates to JR34.3/JR34.4 and JR34.41
0000122
Updated Technical Service Bulletin (TSB) Format
2103322
Transmission Control Module (TCM) Updates
S2208000138RevA
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
0818022
Radio Enhancements Software Level 1848.34 This bulletin involves updating the radio software level to 1848.34. Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch issue, features, modes and App?s change without drivers input (does not affect rearview camera). Wireless connectivity pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.
0901222
Spark Knock/Engine Symptoms This bulletin involves cleaning the piston heads and cylinder head combustion chambersto resolve a spark knock condition being caused by oil intrusion through the PCV system. The customer may describe a knocking or pinging noise coming from the engine upon acceleration.
S2223000063
Ambient Temperature Sensor Servicing.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
2102622
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. The customer may notice the following condition:Poor coast down quality (bump/clunk) at approximately 16-32 kph (10-20 mph) range in manual mode.
9100016
WL trailer tow lighting kit No trailer tow sales codes are required to be added to the vehicle with use of this kit. If sales code XF2 is added to vehicle a DTC error maybe a result.
9100019
Mopar trailer brake controller.
S2008000075RevA
No Start, Start Stop Inoperative, Cluster Message Service Start Stop System
S2208000138
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
1812922
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: P0606 - Internal Control Processor. Customers my also comment on the following: Vehicle in Limp Mode with the Electronic Throttle Control (ETC) light flashing.
1812622
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: P0606 - Internal Control Processor. Customers my also comment on the following:Vehicle in Limp Mode with the Electronic Throttle Control (ETC) light flashing.
9004557
Overhead Console If the sunglasses holder door in the overhead console will not stay closed, inspect the Latch for damage. The Latch is now released for service under part number 68599540A$.
S228A000004RevB
Panasonic VP4R Wi-Fi New Enrollment Pause
2302422
Headlamp Condensation Clearing Procedure This bulletin is to communicate the procedure for headlamp condensation clearing.
9004548RevB
Module, Anti-lock brake system / Hydraulic Control Unit Some 2018-19 WD/WK vehicles have the brake lights staying on without depressing the brake pedal as an affect of DTC C1093-62 occurring or due to an internal failure in the HCU/ABS Module please contact FCA Redacted Content. If there is no response within 15 minutes of initiating your call, please - Obtain a vehicle scan report with the diagnostic environmental data. - Record the Primary Pressure Sensor value ($2002) and the Primary Pressure Sensor offset ($2007). - then, continue with your normal diagnostic process, if possible please avoid seperating the ECU and HCU.
9004548RevA
Module, Anti-lock brake system / Hydraulic Control Unit Some 2018-19 WD/WK vehicles have the brake lights staying on without depressing the brake pedal as an affect of DTC C1093-62 occurring or due to an internal failure in the HCU/ABS Module please contact FCA Redacted Content. If there is no response within 15 minutes of initiating your call, please - Obtain a vehicle scan report with the diagnostic environmental data. - Record the Primary Pressure Sensor value ($2002) and the Primary Pressure Sensor offset ($2007). - then, continue with your normal diagnostic process.
S228A000004RevA
Panasonic VP4R Wi-Fi New Enrollment Pause
9004548
Module, Anti-lock brake system / Hydraulic Control Unit Some 2018-19 WD/WK vehicles have the brake lights staying on without depressing the brake pedal as an affect of DTC C1093-62 occurring or due to an internal failure in the HCU/ABS Module please contact FCA Redacted Content. If there is no response within 15 minutes of initiating your call, please continue with your normal diagnostic process.
S228A000004
Panasonic VP4R Wi-Fi New Enrollment Pause
08-108-22
Flash: Instrument Panel Cluster (IPC) Updates This bulletin involves reprogramming the IPC with the latest available software. Customers may comment on the following:Customer cannot toggle between MPH and KPH speedometer.
S2123000023RevB
The Liftgate Latch Sticks, Will Not Open, Close, Or Hard To Close Manually
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
2301222
Glove Box Hard To Close This bulletin involves replacing the glove box bumpers. Customers may comment on the following: The glove box is hard to close.
0500222
Front Click Noise at Low Speed Turns This bulletin involves installing a friction disc kit on both front hub bearings and rotors. The customer may comment on the following: When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.
S2208000073
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
S2208000072
RKE Does Not Work Or Has Short Range, TPM Is Not Reading Tire Pressures Or Remote Start Is Inoperative
S1708000118
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S1708000118 RevB
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S2208000068
?Device Not Supported? Message on the radio screen
S2209000002
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. When performing diagnosis, an internal engine concern may be suspected.
0802222
Flash: Memory Seat Module (MSM) Updates This bulletin involves reprogramming the MSM with the latest available software. Upon further investigation the technician may find the following stored Diagnostic Trouble Code (DTC): B1D9B-54 - Seat Horizontal Front Stop Not Learned-Missing Calibration. Customers may also experience one or more of the following:Memory seat functionality is inoperative. Memory recall functionality is inoperative. Memory saving functionality to profiles 1 or 2 is inoperative. Easy entry&exit functionality is inoperative.
S2208000013
Memory Seat Settings Can Not Be Recalled, Memory Seat Function Is Inoperative
S1623000034 Rev.
Water Leak From Overhead Console, A Pillar And Or Headliner. Sunroof Drain Tube Inspection.
23-035-21
Rattle Coming From Sunroof This bulletin involves replacing the sunroof fasteners. Customers may comment on the following:Rattle coming from sunroof.
9003895
Front Door Window If the front side door glass has flaws such as delamination, distortion, or cracking, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair. Please take pictures of the affected area of the glass and email the pictures to FCA Redacted Content
S2108000204
Radio Lockup In The Software Installation Screen After Accepting FOTA Update (Incorrect "S2008000204" indicated on published document)
04-001-21
Pentastar Upgrade Oil Fill Level after an Oil Change This bulletin involves rechecking the oil fill level after filling the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.
S2108000198
Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit
05-004-21
Front Click Noise at Low Speed Turns This bulletin involves installing a friction disc kit on both front hub bearings and rotors. The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.
S2108000170
Head unit button stuck DTC code B14DA-2A
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S2008000023
No Crank No Start, Click No Start
S2008000023RevA
No Crank No Start, Click No Start
0810521
UAV and UCV Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to: 39.5. Customers may experience one or more of the following: Lost radio presets. High pitch squeal, pop or humming sound coming from all of the speakers. SXM favorite song list empty. Radio display screen is black when the ignition is on. Radio may reset/reboots, turn itself off and then back on again. Radios resets when a Bluetooth paired phone receives two text messages one after another simultaneously after approximately seven seconds. (ABD sales code). Incorrect navigation address/location/directions. Navigation stuck on loading screen or not appearing at all. Lost navigation settings. Speaker crackling noise on non amplified vehicles (UAV Only). Active call not transferred to vehicle Bluetooth® (UAV Only). Voice Recognition (VR) not understanding commands to switch sources (UAV Only). Bluetooth phonebook not available (UAV Only). "Setting" button removed after ignition cycle (UAV Only). Coolant temperature value incorrect (UAV Only). Speaker crackling noise. In addition the following enhancements are included:Bluetooth improvements. VR improvements. Improve Navigation zoom and scrolling feature on map.
S2125000002
Customer complaint includes a Mil-on condition. Upon further investigation, one or more of the following fault codes may be set in the PCM:
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
S1117000002RevA
Air Suspension System Diagnosis
S2008000059RevB
Error Code 20 Message On the Radio Screen
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S2008000059RevA
Error Code 20 Message On the Radio Screen
S2108000098RevB
Radio Screen Freeze, Blank Screen And Reset
S2108000127 Rev.
Radio Reboot Continually
S2108000127-1
Radio Reboot Continually
S2108000127REVA
Radio Reboot Continually
S2108000127RevA
Radio Reboot Continually
S2108000119
Apple CarPlay Malfunctioning, Does Not Launch Or Is Cutting In An Out On Wired And Wireless Connection, Radio Stuck When IPhone Is Connected
08-094-21
UKA and UKG Radio Enhancements This bulletin involves updating the radio software level to 1848.35. Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (2019 JL with UKA). Radio resets with RPM less than 1000 RPM (2020 JL with UKG and 3.0L Diesel - EXJ).
0809421
UKA and UKG Radio Enhancements This bulletin involves updating the radio software level to 1848.35. Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (2019 JL with UKA). Radio resets with RPM less than 1000 RPM (2020 JL with UKG and 3.0L Diesel - EXJ).
S2108000127
Radio Reboot Continually
S2118000009
Customer complains of a MIL-on condition. Upon further inspection, there is a Diagnostic Trouble Code (DTC) P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) set in the PCM.
S2008000010
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
S2008000010 Rev.
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
9004163
MOLDING, Wheel Flare, Quarter Panel (Wide wheel flares) If you have a Jeep Grand Cherokee Summit, SRT, Trackhawk or Limited X with wide flares that are loose appearing or poor fitting, please document the VIN and provide the following information: 1.) Take image of customer concern - Highlighting flare adhesive surface location where the misaligned/loose/delamination condition is found with respect to the door or body. 2.) Email images of concerns to FCA Redacted Content For additional questions, call FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S2108000120
Radio Volume Uncontrollable Or Changing On Its Own
S2008000087
Memory Seat Does Not Recall Memory Settings
S2008000087 Rev.
Memory Seat Does Not Recall Memory Settings
S2008000087REVA
Memory Seat Does Not Recall Memory Settings
S2108000098
Radio Screen Freeze, Blank Screen And Reset
S2108000098 Rev.
Radio Screen Freeze, Blank Screen And Reset
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
S2008000011
Customer Cannot Change Cluster Display Unit Settings, Turn By Turn Distance Does Not Match The Radios Distance
S2008000011 Rev.
Customer Cannot Change Cluster Display Unit Settings, Turn By Turn Distance Does Not Match The Radios Distance
08-074-21
UGQ, UGV, UJV and UJQ Radio Enhancements This bulletin involves inspecting the software level to see if the radio needs oneor two USB flash drive(s) to update the radio software level to 39.2. Customers may experience one or more of the following: Voice recognition (VR) fails while road names are written in Catalan. After the update to software level MR-28.31, the Amperometer inside Jeepskills shows values too high. The radio may lose some or all programmed presets. Volume blocked/uncontrollable. Heating Steering wheel and seat SK greyed out. Eco Drive trips saved issue. Radio may reset, turn itself off and then back on again. Radio display screen lock up. Park assist chime will continue to chime after the vehicle is turned off. Frequent pop-ups during startup saying device not connected - Uconnect LIVE. Radio will display the incorrect speed limit in kph when approaching a roadspeed camera(2018 WK Only). Uconnect Live Apps restricted to only MyCar, ecoDrive and Jeep Skills(2018 WK Only). Russian language missing in the radio setting menu(2018 WK with UGQ Only). If the radio is set for Russian language, UConnect displays unknown symbolson the ?Off Road Page?(2018 WK with UGQ Only). Could not disable the feature for the heated seat and heated steering wheelturned on automatically at startup(2018 WK with UGQ Only). In addition the following enhancements are included: Navigation improvements. Bluetooth improvements. VR improvements. Russian language enhancements (2018 WK with UGQ Only)
0807421
UGQ, UGV, UJV and UJQ Radio Enhancements This bulletin involves inspecting the software level to see if the radio needs oneor two USB flash drive(s) to update the radio software level to 39.2. Customers may experience one or more of the following: Voice recognition (VR) fails while road names are written in Catalan. After the update to software level MR-28.31, the Amperometer inside Jeepskills shows values too high. The radio may lose some or all programmed presets. Volume blocked/uncontrollable. Heating Steering wheel and seat SK greyed out. Eco Drive trips saved issue. Radio may reset, turn itself off and then back on again. Radio display screen lock up. Park assist chime will continue to chime after the vehicle is turned off. Frequent pop-ups during startup saying device not connected - Uconnect LIVE. Radio will display the incorrect speed limit in kph when approaching a roadspeed camera(2018 WK Only). Uconnect Live Apps restricted to only MyCar, ecoDrive and Jeep Skills(2018 WK Only). Russian language missing in the radio setting menu(2018 WK with UGQ Only). If the radio is set for Russian language, UConnect displays unknown symbolson the ?Off Road Page?(2018 WK with UGQ Only). Could not disable the feature for the heated seat and heated steering wheelturned on automatically at startup(2018 WK with UGQ Only). In addition the following enhancements are included: Navigation improvements. Bluetooth improvements. VR improvements. Russian language enhancements (2018 WK with UGQ Only)
S1818000024
Diesel Fuel Injector Cleaning Procedure
S1818000024 Rev.
Diesel Fuel Injector Cleaning Procedure
S1708000118 Rev.
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination After Key Off
S1908000107
Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated
S1908000107 Rev.
Rear Liftgate Does Not Latch, Liftgate Ajar Lamp Illuminated
S2123000023 Rev.
The Liftgate Latch Sticks Will Not Open, Close, Or Hard To Close Manually
S21230000231
The Liftgate Latch Sticks Will Not Open, Close, Or Hard To Close Manually
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
S2108000096
Rear Wiper Inoperative
S2123000023
The Liftgate Latch Sticks Will Not Open, Close, Or Hard To Close Manually
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
08-053-21 REV. A
Mirror SOS and Assist Buttons Inoperative This bulletin involves replacing the headliner to correct an issue with a missing wiring harness secured to the headliner. Customers may experience the following:The SOS and Assist buttons on the rearview mirror do not work.If the vehicle does not have an active SiriusXM Guardian? subscription this feature will not activate. This repair is to have the SOS and Assist system working so when the subscription is active it will work properly.
0805321
Mirror SOS and Assist Buttons Inoperative This bulletin involves replacing the headliner to correct an issue with a missing wiring harness secured to the headliner. Customers may experience the following:The SOS and Assist buttons on the rearview mirror do not work.If the vehicle does not have an active SiriusXM Guardian? subscription this feature will not activate. This repair is to have the SOS and Assist system working so when the subscription is active it will work properly.
08-053-21
Mirror SOS and Assist Buttons Inoperative This bulletin involves replacing the headliner to correct an issue with a missing wiring harness secured to the headliner. Customers may experience the following: The SOS and Assist buttons on the rearview mirror do not work. If the vehicle does not have an active SiriusXM Guardian? subscription this feature will not activate. This repair is to have the SOS and Assist system working so when the subscription is active it will work properly.
9004362
GLASS, Sunroof If these parts are being ordered to fix a Sunroof wind noise or water leak complaint, please send an email to FCA Redacted Content before disassembly. If no response in 15 minutes, please proceed with the repair
S1723000007 Rev.
Air Suspension Inoperative And Or Compressor Freeze Up Or Sticking In Cold Weather.
S1723000007RevF
Air Suspension Inoperative And Or Compressor Freeze Up Or Sticking In Cold Weather.
S2108000084
CEL (Check Engine Lamp) On, DTC P0197 Engine Oil Temperature Low
S2108000080
Radio Replacement Reset Routine, Radio Has Missing Icons Or Are Grayed Out
S2008000011RevB
Customer Cannot Change Cluster Display Unit Settings, Turn By Turn Distance Does Not Match The Radios Distance
S2124000004
A/C does not cool and vehicle is low on Freon charge but no leak is found with sniffer or black light anywhere in the system
S2123000010
Vehicle Sway At Very Low Speed While Being Flat Towed Behind A RV
S2123000010 Rev.
Vehicle Sway At Very Low Speed While Being Flat Towed Behind A RV
18-026-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may notice the following condition:The oil change interval is too short. The oil change message shows up at around 12,000 km / 7,456 mi or earlier and the normal oil change interval is 12 months or 20,000 km / 12,427 mi.
1802621
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may notice the following condition:The oil change interval is too short. The oil change message shows up at around 12,000 km / 7,456 mi or earlier and the normal oil change interval is 12 months or 20,000 km / 12,427 mi.
S2008000011RevA
Customer Cannot Change Cluster Display Unit Settings, Turn By Turn Distance Does Not Match The Radios Distance
S2108000045
Favorite Song On-Air Alert List Empty
S2108000047
Jeep Off Road Pages Missing Latitude And Longitude Coordinates
S2108000040
Blind Spot Unavailable Message Displayed On Cluster
9004349
MASTER CYLINDER, Brake For a brake pedal feel complaint, power bleed the brake system to try and resolve the issue before replacing the master cylinder.
S2108000024 Rev.
Crank No Start Condition, No DTC?s
08-015-21
Radio Enhancements This bulletin involves updating the radio software level to 1848.34. Customers may experience one or more of the following:Radio display screen flickers. Radio resets with RPM less than 1000 RPM (DT and JL with 3.0L Diesel). Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.
S2123000006
Squeak Chirp Creak Noise From Left Quarter Panel Area
S2109000001
Customer may complain of a MIL lamp on. Upon further investigation there could be a fault code in the PCM for P1524 ? Oil Pressure Out of Range ? Camshaft Advance/Retard Disabled.
S1709000010 Rev.
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S2008000031 Rev.
Low Charging Voltage Displayed On Cluster
9004342
WINDSHIELD Windshield cracked or blemish. When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.
S1908000083 Rev.
Check Engine Light Illuminated, Stop Start Function Inoperative
09-013-20 REV. A
3.6L Pentastar Upgrade Spark Plug Internal Crack This bulletin involves replacing all six spark plugs. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may also comment on the following:Rough running engine.
09-013-20
3.6L Pentastar Upgrade Spark Plug Internal Crack This bulletin involves replacing all six spark plugs. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may also comment on the following: Rough running engine.
S2023000045
Wind Noise Or Fluttering When Driving at Highway Speeds
18-079-20 REV. A
Flash: Powertrain Control Module (PCM) Updates - AN-K8-18-20201102 Refer to China Joint Venture (JV) released document AN-K8-18-20201102, for details on this service action.
1807920
Flash: Powertrain Control Module (PCM) Updates - AN-K8-18-20201102 Refer to China Joint Venture (JV) released document AN-K8-18-20201102, for details on this service action.
S2008000181
No Start Condition, Low Battery Voltage And Battery Light On, DTC P2503, P2504 Active Or Stored
S2023000043
Clunk Or Pop Noise From Front Suspension On Rough Road
S2008000175
8.4" Touchscreen Display Electrostatic Discharge Failure
S1625000005
(Rev. A) Malfunction Indicator Light (MIL) Illuminated. Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.
S1625000005 Rev.
(Rev. A) Malfunction Indicator Light (MIL) Illuminated. Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.
S2008000172
Radio Screen Flickering When Using Apple CarPlay Or Android Auto.
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100220
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
05-002-20
Front Click Noise at Low Speed Turns This bulletin involves installing a friction disc kit on both front hub bearings and rotors. The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.
0500220
Front Click Noise at Low Speed Turns This bulletin involves installing a friction disc kit on both front hub bearings and rotors. The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.
08-092-20
Improper Up Shift With Paddle Shift This bulletin involves replacing both steering wheel paddle shifter. Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead.
0809220
Improper Up Shift With Paddle Shift This bulletin involves replacing both steering wheel paddle shifter. Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead.
18-092-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following (DTC) has been set:P00FD-00 - Battery B State Of Charge Performance.
1809220
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following (DTC) has been set:P00FD-00 - Battery B State Of Charge Performance.
S2008000150
No Crank, No Start, Multiple DTC?s For Loss Of Communication Or Ignition Circuit Open Setting In Multiple Modules
08-086-20
Flash: Battery Pack Control Module (BPCM) Updates - AN-K8PHEV-18-20200925 Refer to China Joint Venture (JV) released document AN-K8PHEV-18-20200925, for details on this service action.
08-087-20
Flash: Power Inverter Module (PIM) Updates - AN-K8PHEV-18-20200927 Refer to China Joint Venture (JV) released document AN-K8PHEV-18-20200927, for details on this service action.
18-091-20
Flash: Powertrain Control Module (PCM) Updates - AN-K8PHEV-18-20200926 Refer to China Joint Venture (JV) released document AN-K8PHEV-18-20200926, for details on this service action.
S1921000007 Rev.
(Revision A) Engine Restarting On Stop/Start Event Without Releasing The Brake Pedal, EVIC Displays Shift To P Then Desired Gear, D on PRNDL Flashing
9001496
CAP, Engine Oil, Fill (O RING, Oil Filler Cap) For all model years, models and engines using oil fill caps with O-Ring seals: These O-Rings are now available for service. The green O-Ring is part 68029299A$. The black O-Ring is to be serviced by the green O-Ring. The blue O-Ring (thicker cross section than green & black) is part 68029300A$.~ If ordering this oil filler cap for a warranty repair due to a damaged/missing O-ring, please note that returned caps replaced for an O-ring issue will be subject to chargeback.
S2008000115
There Is No Backup Camera Image Displayed When Shifting To Reverse. DTC?s U0264-00 And B280B-00 May Be Set
S1817000003 Rev.
(Revision A) Clunk Noise From Rear Suspension
S2008000141
Navigation Shows Incorrect Location
S2008000083 Rev.
(Revision A) Clusters Distance To Turn Value Does Not Match The Radio Head Unit Value Navigation
S2008000137
Airbag Light Is On Or Power Door Locks Inoperative. DTC?s U113D-00, B25AF-2A, B1830-11, B182C-11, And B007F-11 May Be Present.
18-079-20
Flash: Powertrain Control Module (PCM) Updates - AN-K8-18-20200824 Refer to China Joint Venture (JV) released document AN-K8-18-20200824, for details on this service action.
9004297
SENSOR, Tire Pressure For concern of TPM warning lamp on or missing signal related DTCs, please ensure correct TPMS diagnosis and repair. In order to determine proper root cause, please note if sensors are broken and email pictures of sensor before removal to FCA Redacted Content. Analysis of TPM Sensor warranty returns are reported back as TNF or TPM Sensors are returned damaged( cracked or broken) and cannot be analyzed to determine failure mode.
S2008000130
Radio UConnect GPS Based Trip Computer Missing
S2008000122
Blind Spot LED Stays ON. DTC B285F-15 Blind Spot Warning Light Control-Circuit Short To Battery Or Open
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
09-001-20 REV. A
Oil Filter Upgrade This bulletin involves replacing the existing engine oil filter with an upgraded version. This action is a proactive product improvement which adds enhanced filtration and flow performance for the upgraded filter.
0900120REVA
Oil Filter Upgrade This bulletin involves replacing the existing engine oil filter with an upgraded version. This action is a proactive product improvement which adds enhanced filtration and flow performance for the upgraded filter.
9004279
Exterior Emblems/Badging For exterior emblems/badges that appear to be loose, crooked, or missing, please document the VIN and provide the following information: 1.) Take image of customer concern 2.) Email images of concerns to FCA Redacted Content For additional questions, call FCA Redacted Content. If no response in 15 minutes, proceed with repair.
08-037-20 REV. A
UAV and UCV Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to:. UAV radios - 34.2. UCV radios - 30.21. Customers may experience one or more of the following:Speaker crackling noise on non amplified vehicles (UAV Only). Active call not transferred to vehicle Bluetooth® (UAV Only). Voice Recognition (VR) not understanding commands to switch sources (UAV Only). Bluetooth phonebook not available (UAV Only). "Setting" button removed after ignition cycle (UAV Only). Coolant temperature value incorrect (UAV Only). Speaker crackling noise.
0803720
UAV and UCV Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to:. UAV radios - 34.2. UCV radios - 30.21. Customers may experience one or more of the following:Speaker crackling noise on non amplified vehicles (UAV Only). Active call not transferred to vehicle Bluetooth® (UAV Only). Voice Recognition (VR) not understanding commands to switch sources (UAV Only). Bluetooth phonebook not available (UAV Only). "Setting" button removed after ignition cycle (UAV Only). Coolant temperature value incorrect (UAV Only). Speaker crackling noise.
S2008000104
During A WiTech Session The ABS And Traction Control Lights Turn On. Multiple ABS And PCM DTC?s Set
S2008000094
Uconnect Market Place APP Fatal Error Message
S2008000100
Trailer Wiring Connector Adapter 4-Pin And 7-Pin Circuit Identification
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
S2008000075
No Start, Start Stop Inoperative, Cluster Messages to Service Shifter or Service Start Stop System
S2018000008
Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)
S2008000089
SGW (Security Gateway Module) Setting DTC B235A-00 ECU In-Plant- Mode
S19080000047
Volume Uncontrollable Or Stuck On High
S1908000047
Volume Uncontrollable Or Stuck On High
S2008000002
Speaker Makes Crackle Popping Noise
S1908000174
Radio Screen Black At Vehicle Startup After A Sleep Cycle
S2008000083
Clusters Distance To Turn Value Do Not Match The Radio Head Unit Value
S1721000016
Service 4wd Light On, Message AWD System Service Required
S2008000077
VP2R Radio Clock Not Keeping Time
S1909000002
Customer complaint may include an overfilled engine crankcase after an oil change.
S2008000073
VP4 Panasonic Radio USB Software Update Error Codes And Guidelines For Recovery
S2008000071
Mirror Blind Spot Indicators Stay Illuminated
S2008000070
Heated Seats, Heated Steering Wheel And Ventilated Seats Inoperative
9004258
SENSOR, Park Assist For diagnostic issues relating to any of the following Park Assist error conditions: ·SERVICE PARK TRONICS ON CLUSTER ·VEHICLE WITH FAULT B1297-12-PTS SENSOR. ·CUSTOMER STATES PARK ASSIST NOT WORKING WITH SENSOR INOP The Product Development team requests that photos be taken of any suspected failed sensors before any repair to the sensor is started on the vehicle. Also, please email a copy of the VSR and sensor photos to the following FCA engineers: FCA Redacted Content We will review the scan report and photos, and let you know the next steps as soon as we can. If no response in 15 minutes, proceed with repair.
S2008000055
Battery Vent Tube Does Not Align With Some New Battery Installations
S2023000026
Liftgate Will Not Power Close Liftgate Ajar Light Will Be On. Liftgate Will Not Power Open.
S1723000007
Air Suspension Inoperative And Or Compressor Freeze Up Or Sticking In Cold Weather.
23-015-20
Disinfectant Solution Recommended for COVID-19
S2008000059
Error Code 20 Message On the Radio Screen
S2008000060
Radio Issues With iPhone 11
18-041-20
Powertrain Control Module (PCM) Replacement - P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation) This bulletin involves replacing the Powertrain Control Module (PCM) and re-programming with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Code (DTC) set in the PCM memory:P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation).
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
9004213
HEADLAMP After performing the headlamp condensation clearing service procedure, If the headlamp is being replaced for Moisture / Condensation issue, please e-mail pictures of the Moisture / Condensation issue to FCA Redacted Content
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
18-035-20
Fuel Vapor Hose Not Connected This bulletin involves inspecting and connecting a loose fuel vapor hose. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set:P0441 - EVAP Purge System Performance. P0456 - EVAP System Small Leak. P0455 - EVAP System Large Leak. Customer or technician may also experience the following:Fuel odor smell in the left rear wheel opening.
S2008000045
Apps Or Icons Grayed Out
S2023000021
Water Leak At Rear Lift Gate D Pillar.
S2005000003
ABS And ESP Warning In EVIC C0037-1D C003A-1D
S1808000175
LED Front Fog Lamps Flicker Or Intermittently Light, Are Dim Or Inoperative. A U11E9, or B16FB-15 may be set
S1908000208
Satellite Radio Inoperative Radio Has Code B156B-13.
S2008000030
Overhead Console, Liftgate, Dome Light And Sunroof Controls Inoperative
08-037-20
UAV and UCV Radio Enhancements This bulletin involves inspecting and if required, updating the radio software levelto 30.21. Customers may experience one or more of the following:Speaker crackling noise.
21-019-20
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. The customer may notice one or more of the following conditions:A loud whistle noise upon engine start up. Rough and/or erratic transmission shifting between gears during normal drive cycles.
S1823000048
Creaking Noise From Front Of Vehicle With Body Flex
9004223
BATTERY, Auxiliary (180 AMP) Mopar Engineering has reviewed the BBAUA180AA battery due to concerns over fitment in Chrysler, Jeep®, Dodge & Ram vehicles and has provided direction on usage. BBAUA180AA CAN BE USED in the following vehicles equipped with stop/start technology: ?MP ? Jeep Compass ?JL ? Jeep Wrangler ?JT ? Jeep Gladiator ?RU ? Chrysler Pacifica RU NOTE: Modify the BBAUA180AA battery positive mold cover by trimming 3mm of rubber on left side & bottom. ?WK ? Jeep Grand Cherokee ?WD ? Dodge Durango WK/WD NOTE:A vent kit is being created now and will replace the existing tube with a longer one and add an elbow to it for routing (availability is TBD).
S2008000013
Key Programming, Security Pin Request, Pin Invalid
S2023000010
Power Lift Gate Opens 1 To 2 Feet Then Closes
08-016-20
Body Control Module (BCM) Reconfigure for Enabling the Auto-On Comfort Settings This bulletin involves reconfiguring the BCM and possibly a radio reset, to enable the auto-on comfort settings. Customers may comment on one or more of the following:If below 4 °C (40 °F), the heated seats or heated steering wheel turn on by themselves. If above 26 °C (80 °F), the vented seats turn on by themselves. Cannot turn off the auto-on comfort feature. With the symptom/condition listed above, there?s no setting in the radio to turn the auto-on comfort feature off.
09-005-19 REV. A
Oil Filter Upgrade This bulletin involves replacing the existing engine oil filter with an upgraded version. This action is a proactive product improvement which adds enhanced filtration and flow performance for the upgraded filter.
08-124-19
Radio Enhancements This bulletin involves updating the radio software level to 1848.24. Customers may experience one or more of the following: Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.
09-005-19
Oil Filter Upgrade This bulletin involves replacing the existing engine oil filter with an upgraded version. This action is a proactive product improvement which adds enhanced filtration and flow performance for the upgraded filter.
9004148
SPEAKER, 6"x9" Right or Left For a buzz squeak rattle (BSR) concern coming from the speaker area that cannot be recreated, the fastener in the armrest pull cup may not be fully torqued. If a customer has concerns about speaker pop or speaker rattle, please enusre that Radios is at latest software level. This fastener, if under torqued, causes the washer to spin and rattle. Please ensure this fastener is secured and washer is not spinning prior to speaker replacement. Additional info: Please verify that there are no loose screws in door pull cup, no bent 6x9 speaker tinsel wire, or audio induced pop/crackle event(non BSR) Please crate and send a copy of the vehicle scan report and specify radio sw version and radio head unit ID to engineers via phone call or email at the following: michael.onyia@fcagroup.com (248) 613-2380 anmol.shergill@external.fcagroup.com (313) 412-0607 matt.berg@fcagroup.com (248) 576- 7754 If no response in 15 minutes, proceed with repair.
08-117-19 REV. A
Flash: Security Gateway Module (SGW) Enhancements This bulletin involves updating the Security Gateway Module (SGW) with the latest available software. Technicians may notice that the vehicles SGW is not at the latest software level.
08-117-19
Flash: Security Gateway Module (SGW) Enhancements This bulletin involves updating the Security Gateway Module (SGW) with the latest available software. Technicians may notice that the vehicles SGW is not at the latest software level.
0811719
Flash: Security Gateway Module (SGW) Enhancements This bulletin involves updating the Security Gateway Module (SGW) with the latest available software. Technicians may notice that the vehicles SGW is not at the latest software level.
9003730
SI-eVT Transmission - China Variant & 9 inertia ring bolts For SI-eVT Transmission ONLY: Replace the nine (9) flywheel to damper bolts (68382486AA) when replacing the SI-eVT per TechConnect procedure. SI-eVTs built prior to January 11, 2019 had a 05192374AB level cooler. Using service SI-evT built after Jan 11 2019 with the 05192374AC level cooler requires new 68238385AB inlet hose and 68238386AC outlet hose. The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
21-038-19
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience one or both of the following conditions:Poor shift quality or ?bump? experienced during 3-2, 2-1 coastdowns.
18-074-19
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may comment on the following condition: Perceive rough and/or erratic transmission shifting between gears during normal drive cycles.
21-036-19
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. The customer may notice the following condition: Rough and/or erratic transmission shifting between gears during normal drive cycles.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.