S238A000038 REV.D
Service Bulletin/Repair Instructions
Auto Emergency Braking (AEB) Unavailable – Service Required Message In Cluster
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S238A000038 REV.D
Auto Emergency Braking (AEB) Unavailable – Service Required Message In Cluster
S2609000011
MIL-On and/or Engine Oil Leak
9100905
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
9100902
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S2623000052 REV. A
Airbag Warning Light On or Intermittent. The Occupant Restraint Controller (ORC) May Have The Following DTCs (Active/Stored)
114265
TRANSMITTER KIT & TRANSMITTER - INTEGRATED KEY FOB
114268
TRANSMITTER KIT & TRANSMITTER - INTEGRATED KEY FOB
S2623000001 REV.A
Rotary Shifter Lights Blinking, Shifter Not Moving, Not Going Into Gear.
S2508000029 REV.B
Instrument Panel Cluster (IPC) Message “Park Assist System Unavailable” or “Service Park Assist System”, “Rear Braking Assist Unavailable” or “Service Rear Braking Assist System" with Performance Diagnostic Trouble Codes (DTCs)
S2523000032 REV.B
Steering Dragging While Recreational Flat Towing Behind RV.
S2623000052
Airbag Warning Light On or Intermittent. The Occupant Restraint Controller (ORC) May Have The Following DTCs (Active/Stored)
S2508000029 REV.A
Instrument Panel Cluster (IPC) Message “Park Assist System Unavailable” or “Service Park Assist System”, “Rear Braking Assist Unavailable” or “Service Rear Braking Assist System" with Performance Diagnostic Trouble Codes (DTCs)
113801
SEAL - LOWER AGS
S268A000016
R1L Radio Screen Goes Blank after transitioning from logistic to customer mode
113553
EVAPORATOR - AIR CONDITIONING
113554
EVAPORATOR - AIR CONDITIONING
113557
EVAPORATOR - AIR CONDITIONING
113558
EVAPORATOR - AIR CONDITIONING
S2524000009 REV.A
Customer Indicates Air Conditioning Blows Warm.
08-274-26
Power Folding Seat Wire Harness Pinched Customers may experience one or more of the following: SYMPTOM: ● Battery is depleted. NOTE: Battery depletion may be due to a pinched power folding seat wire harness behind the left quarter panel by the cargo tie down fastener. ● Loss of function of the rear folding seats. ● Rear folding seat behavior is not functioning as expected. This bulletin involves repairing a pinched power folding seat wire harness behind the left quarter panel.
9100859
Before replacing any part, check the DOT on the glass or the PN to make sure you choose the replacement part from the correct supplier: DOT 615 - 6NC10TRMAH - CIE Supplier DOT 1038 - 6NC07TRMAR - CIE Supplier DOT 1065 - 7TF32TRMAB, 7TF33TRMAB - HCMF Supplier
113240
SPARK PLUG - NONE
113241
SPARK PLUG - NONE
08-268-26
SXM Radio Doesn't Reflect Station Or Song Changing Customers may experience the following: SYMPTOM: ● When playing SXM stations the radio does not reflect the current station or recognize a song changing.
9100833 REV1
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S2508000025 REV. B
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
112639
THROTTLE BODY – NONE
112640
THROTTLE BODY – NONE
113123
SPRING KIT - DISC BRAKE PAD
9100849Rev1
WL: Dealer cannot perform programming new keyfob or re-programming existing keyfob. While programming a new keyfob (or) re-programming an existing keyfob, If the technician presses the keyfob for longer time causing multiple blinks on the keyfob can lead to programming failure. Tech to press keyfob only once until they observe single blink on the keyfob to allow keyfob the programming to be completed.
S2508000025 REV.A
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
9100811 Rev 4
Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
9100848
If the Driver/Passenger Seat Adjsuter Switch is inoperable, seat back will not move or seat moves on its own: 1.Which function is not operating properly? *Forward/Backward *Recline Forward *Recline Backward *Height Adjustment *Multiple Functions 2.Is the concern constant or Intermittent? 3.If intermittent, how often does it occur? Daily, Weekly, Randomly 4.Does the seat move on its own without pressing any switch? Yes / No 5.Does the issue occur only while driving, only at key-on, or while the vehicle is parked? 6.Has the concern occurred after the vehicle has been sitting for an extended period (overnight or several hours)? 7.Does pressing the switch multiple times temporarily restore operation? 8.Have any other seat functions or electrical features been affected at the same time? 9.Has the seat adjuster switch or seat assembly been previously repaired or replaced? Before replacing the seat adjuster switch, verify power, ground, connector engagement, wiring integrity, and inspect for blown fuses or damaged harnesses. If no external issues are found and the concern is verified, an intermittent internal switch failure should be considered.
9100849
WL: Dealer cannot perform programming new keyfob or re-programming existing keyfob. While programming a new keyfob (or) re-programming an existing keyfob, If the technician presses the keyfob for longer time causing multiple blinks on the keyfob can lead to programming failure. Tech to press keyfob only once until they observe single blink on the keyfob to allow keyfob the programming to be completed.
S2102000004 REV.D
WL Front Control Arm Bushing - Handling Link Has Loose Rubber Appearance
112979
CAMERA - REAR VIEW
112980
CAMERA - REAR VIEW
S2623000041 REV.A
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed. Rev A
112842
BOLT - HEX FLANGE HEAD
9100833
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S268A000014
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
08-240-26
Flash: Trailer Tow Module (TTM) Updates Customers may comment on one or more of the following: SYMPTOM: ● If the vehicle is traveling at less than 05 kph (03 mph) and the brake pedal is pressed, then both trailer turn lights will flash for two milliseconds. ● If the vehicle is traveling at less than 05 kph (03 mph) and one turn light is activated, then the opposite trailer turn light will flash for 20 milliseconds. This bulletin involves reprogramming the TTM with the latest available software.
112856
HEATER - ELECTRIC COOLANT
112857
HEATER - ELECTRIC COOLANT
S1623000028 Rev. K
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
112645
HEATER CORE – NONE
S2503000001 REV.A
Service 4WD Message, With Any Combination Of The Following Front Axle Disconnect (FAD) Diagnostic Trouble Codes
9100834
Ambient cabin light fault B2811-02 inop. If Ambient Lights can change color and intensity, do not replace Auxiliary/Ambient Lighting Module (ALM). Follow the diagnostic for B2811-02. Before replacing, verify the vehicle PROXI is correct for the vehicle (2-row/3-row). If PROXI is incorrect, re-PROXI and then perform a hard reset of the ALM.
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S1623000028 REV.J
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
S2623000041
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed.
08-221-26 REV. A
R1H Radio U41.10 USB Software Update Customers may experience one or more of the following: ● FCW OFF light ON with no DTCs and can't turn off. ● Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera Functions Normally). ● Paddle shifters not working/no longer a setting. ● Autolocks not working. ● Auto headlights not working. ● AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). ● Album Art flickering issue. ● Blank screen and then reboot every 2 minutes and 40 seconds. ● CarPlay icon disappears from main screen while still active, leaving no navigation path back. ● Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after FOTA. ● Valet mode sends duplicate requests causing HU and vehicle state misalignment. ● Rear seat media page intermittently shows a blank screen. ● Unable to select or drag 'Pitch and Roll' widget on home screen. ● USB playback resumes incorrectly, skipping to next track after reconnect. ● Album art not displayed on HMI despite availability in media. ● Incorrect call timer displayed for conference calls. ● Call status remains 'active' on widget after call ends. ● Second call status not updated on home screen widget. ● Rear entertainment tab intermittently blank when switching apps. ● System crashes for 20 to 30 seconds after voice reply action. ● Media progress bar continues incorrectly after second call acceptance. ● CarPlay device fails to reconnect automatically or manually. ● Rear HVAC lock/unlock text missing while icon is present. ● Visual glitch observed on Front Passenger Display Module (FPDM) display. ● Surround view camera accessible while driving across apps (unexpected behavior). ● IPC navigation map fails to load despite radio showing navigation. ● Head Up Display (HUD) layout resets after overnight sleep cycle. ● ParkSense triggers unintended surround camera activation. ● HUD settings not retained after ignition cycle. ● Audio focus stuck on VR; selected message not read. ● Preset bar appears blank after overnight sleep cycle. ● FM channel switches unexpectedly and reverts after delay. ● Massage activation causes HU black screen/media disruption. ● Non-applicable ambient lighting setting visible in vehicle menu. ● Navigation screen appears black after system startup. ● Track name flickers on status bar during CarPlay playback. ● HU toggles between Home and Media screens without user input. ● Phantom touch causes navigation to switch from full screen to split view. ● HU redirects to CarPlay tab when exiting camera unexpectedly. ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (Rearview Camera Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (Rearview Camera Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (Rearview Camera Functions Normally). ● Ghost touch on Navigation screen (Rearview Camera Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after view camera event selected by customer in the Camera View Pages (Rearview Camera Functions Normally). This bulletin involves inspecting and if required, updating the radio software level to U41.10. Depending on the radio's current software level the radio may need a one or two USB update.
OTHERDOC_164
Radio Over The Air Update to U41.10 R1H Software Version (FOTA) Customers may experience one or more of the following: Inaccurate status or information displayed during phone calls- Voice Recognition performance- Carplay connectivity issues- Black / blank screens for Navigation or Media apps not affecting rearview camera funtionality- Visual glitch on Front passenger Display- Unresponsive widgets- Light & Dark mode discrepancy between screen views- Unresponsive hard button to turn screen off- Incomplete or innacurate pop-up notifications- Radio stuck in Valet Mode- Phantom / Ghost touch on Media screens- Incorrect menu displayed
111785
MODULE - CENTRAL ADAS DECISION and DRIVER MONITORING
S1623000028 REV.I
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000038
Central ADAS Decision Module (CADM), Long Range Camera Front(LRCF), Advanced Driver Assist System (ADAS), Lane Assist Inoperative, Service Active Lane Management Message, Inside Rearview Mirror Cover and LRCF Windshield Bracket.
112552
D-26-13 Rev. A Claim Submission for Hurricane Spark Plug Repair
112535
Claim Submission for Hurricane Spark Plug Repair
112198
MODULE - LIFTGATE
9100811Rev3
***68375577A$ is not showing the correct verbiage please update and correct*** Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
23-019-26
Hot Cup Holders Customers may comment on the following: ● When the rear heat temperature is set at or near max hot output, the front center console's surfaces, first row and second row cup holders and storage bins are getting warm to the touch. This bulletin involves removing the front center console and installing an insulator foam pad on top of the Center Console air duct.
08-221-26
R1H Radio U41.10 USB Software Update Customers may experience one or more of the following: ● **FCW OFF light ON with no DTCs and can't turn off. ● Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera (RVC) Functions Normally). ● Paddle shifters not working/No longer a setting. ● Autolocks not working. ● Auto headlights not working. ● AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). ● Album Art flickering issue. ● Blank screen and then reboot every 2 minutes and 40 seconds. ● CarPlay icon disappears from main screen while still active, leaving no navigation path back. ● Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after FOTA. ● Valet mode sends duplicate requests causing HU and vehicle state misalignment. ● Rear seat media page intermittently shows a blank screen. ● Unable to select or drag 'Pitch and Roll' widget on home screen. ● USB playback resumes incorrectly, skipping to next track after reconnect. ● Album art not displayed on HMI despite availability in media. ● Incorrect call timer displayed for conference calls. ● Call status remains 'active' on widget after call ends. ● Second call status not updated on home screen widget. ● Rear entertainment tab intermittently blank when switching apps. ● System crashes for 20 to 30 seconds after voice reply action. ● Media progress bar continues incorrectly after second call acceptance. ● CarPlay device fails to reconnect automatically or manually. ● Rear HVAC lock/unlock text missing while icon is present. ● Visual glitch observed on FPDM display. ● Surround view camera accessible while driving across apps (unexpected behavior). ● IPC navigation map fails to load despite HU showing navigation. ● HUD layout resets after overnight sleep cycle. ● ParkSense triggers unintended surround camera activation. ● HUD settings not retained after ignition cycle. ● Audio focus stuck on VR; selected message not read. ● Preset bar appears blank after overnight sleep cycle. ● FM channel switches unexpectedly and reverts after delay. ● Massage activation causes HU black screen/media disruption. ● Non-applicable ambient lighting setting visible in vehicle menu. ● Navigation screen appears black after system startup. ● Track name flickers on status bar during CarPlay playback. ● HU toggles between Home and Media screens without user input. ● Phantom touch causes navigation to switch from full screen to split view. ● HU redirects to CarPlay tab when exiting camera unexpectedly.** ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally) This bulletin involves inspecting and if required, updating the radio software level to **U41.10.** Depending on the radio's current software level the radio may need a one or two USB update.
112199
MODULE - LIFTGATE
9100811 REV1
Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
08-217-26
Heads Up Display (HUD) Resets to Default Settings Each Ignition Cycle Customers may experience the following: ● The custom HUD configurations do not save after a vehicle sleep cycle. HUD configuration will reset to the default settings.
112180
BEZEL - OVERHEAD CONSOLE
21-041-26
Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode This bulletin involves replacing the transmission oil pump.
9100532 REV1
Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, Electronic Stability Control (ESC) light on, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced. Note: WL / WS SCCMs do not contain a Steering Angle Sensor (SAS) The Steering Angle is computed within the Electronic Power Steering (EPS) module. See Electronic Power Steering (EPS) module for diagnosis and repair procedures.
9100786 Rev 1
TBM2.0H Setting U0080-00. Do not replace TBM ECU or SGW. If replacement is determined, Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only. Under certain conditions, SGW Module may take longer to establish Ethernet communication after boot up. If it takes longer than 30 seconds, The TBM2.0H module will set DTC U0080 - Ethernet Bus 1. As soon as SGW responds, the TBM2.0H will demature the DTC and move it to STORED. This issue should not cause any customer related symptoms. Do not replace the following TBM Part Numbers: WL: 68639445AF,68637489AE,68663479AE. WS: 68734941AA,68729188AC. EJ: 68592344AI. KM: 68592343AL,68735975AD. DT: 68634362AJ,68624784AF,68624784AE,68735493AB,68735493AA. DJ (HDCC): 68608721AJ. If the TBM2.0H module has set the DTC U0080 and it is STORED or ACTIVE, please clear the fault and do nothing. No further diagnostics is required. ---------------------------------------------------------------------------------------------------- TBM2.0H Setting DTC B1E21 Do Not Replace the TBM ECU. Is triggered when the TBM Backup Battery is discharged, inactive, or drained. This can happen during the lifetime of the vehicle. TBM should NOT be replace for B1E21, since there is no fault on TBM. TBM battery is replaceable. Part number of the back-up battery inside TBM is 68597650AA. Do not replace the following TBM Part Numbers: WL: 68639445A$, 68663479A$. -------------------------------------------------------------------------------------------------------- TBM Setting DTC U0499-00 Please refer to SOL S268A000004 if you are attempting to replace or repair the telematics box due to DTC U0499-00. This DTC does not cause direct customer impact and cannot be cleared. Engineering is working on TBM software enhancements, tentative Q2 2026. Do not replace the following TBM Part Numbers: KM: 68592343A$
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
09-009-26
PHEV Engine Replacement XC2 Warranty Extension Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P2336 - Cylinder 1 Above Knock/Combustion Vibration Sensor Threshold. ● P2337 - Cylinder 2 Above Knock/Combustion Vibration Sensor Threshold. ● P2338 - Cylinder 3 Above Knock/Combustion Vibration Sensor Threshold. ● P2339 - Cylinder 4 Above Knock/Combustion Vibration Sensor Threshold. The customer may also describe the following: ● A knocking noise from the engine compartment This bulletin involves replacing the engine.
111833
SENSOR – KNOCK
111834
SENSOR – KNOCK
112147
D-26-11 (XC2) 2.0L PHEV Engine - Select 2024 - 2025 Jeep Wrangler (JL) and 2023 - 2025 Grand Cherokee/ Grand Cherokee L (WL)
112149
ID-26-24 (XC2) 2.0L PHEV Engine - Select 2024 - 2025 Jeep Wrangler (JL) and 2023 - 2025 Grand Cherokee/ Grand Cherokee L (WL)
111749
FRAME - CARGO AREA
9100781 Rev 1
Issue: complaint of rattle from exhaust Before replacement: Check for loose exhaust Aluminum isolator brackets (check if the bracket is movable by hand/bolts not fully fastened to the vehicle). If loose, tighten and check to see if the rattle is still present. Check clearances between exhaust components and isolators brackets, as well as other parts of the vehicle. If the hanger braces (additional rods welded to the hanger rod for strengthening) are bottomed out on the isolator, loosen the clamps joining the catalytic-side and muffler-side systems and slide the muffler side exhaust back 5mm. Take care not to damage the system, do not use a hammer to break the muffler side free. Re-tighten and check for rattles again. If the rattle is still present, replace the system.
9100811
Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the tension link. This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
S248A000015 REV.A
Poor Audio Quality And Or Static From Wireless Devices
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
111702
SWITCH - LIFTGATE
08-207-26
Instrument Panel Cluster (IPC) Flicker Turn By Turn The customer may experience flickering on their Instrument Panel Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay
08-197-26
Flash: Instrument Panel Cluster (IPC) Updates Customers may experience the following: ● While in the offroad page on the IPC, there is a delay in updating the graphics and other information This bulletin involves reprogramming the IPC with the latest available software.
111619
ACTUATOR - A/C AND HEATER
111620
ACTUATOR - A/C AND HEATER
S2102000004 REV.C
WL Front Control Arm Bushing - Handling Link Has Loose
S2308000034 REV.B
No Wireless Charging Or Slow Wireless Charging
9100446 Rev 5
BSR from the front suspension. Investigate the disconnecting stabilizer bar for a broken or cacked weld on the upper mount (anti rotation bracket). Instead of the replacing the whole stabilizer bar use Kit #PN#68730602AB. Refer to SOL #S2502000002 for additional information.
S2523000003 REV.A
Door Latch, Handle And Ajar Additional Service Information.
S2623000028
Manual Liftgate / Hatch Ajar Message On Instrument Cluster.
08-075-26 REV. A
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S2623000024
U0422-00 Implausible Data From BCM Set In Central ADAS Decision Module (CADM).
S2624000005
Driver Side Heat Blows Warm
111405
COVER - CYLINDER HEAD
111406
COVER - CYLINDER HEAD
S2623000022
Buzz Squeak Rattle (BSR) Noise From Rear Of Vehicle.
08-143-26
Traffic Sign Assist Unavailable – Service Required The customer may experience one or more of the following: SYMPTOM: ● “Traffic Sign Assist Unavailable – Service Required” message and icon displays on the Instrument Panel Cluster (IPC). This occurs after a remote start and typically at the first start of the day. ● The Odometer flashes when the traffic alert message is active. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
08-141-26
Flash: Power Liftgate Module (PLGM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B1945-13 - Power Liftgate Pinch Sensor 2-circuit Open. ● B197B-29 - Ratchet Fork Switch-signal Invalid. ● B197C-29 - Pawl Detent Switch-signal Invalid. ● B197D-29 - Gear Position Switch 1-signal Invalid. ● B197E-29 - Gear Position Switch 2-signal Invalid. Customers may experience the following symptom: ● The power liftgate will not open or close. This bulletin involves replacing the right side pinch sensor and reprogramming the PLGM with the latest software.
S1623000028 REV.H
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2223000022 REV.E
Power Liftgate Inoperative Or Intermittently Will Not Open Or Close.
111121
SWITCH - POWER WINDOW
111124
SWITCH - POWER WINDOW
S2408000016 REV.E
Front Passenger and/or Rear Left and/or Rear Right Door Window Switches are Inoperative, Window Operation Works from the Driver Master Switch
111118
COVER - CARGO AREA
9100786
TBM2.0H Setting U0080-00. Do not replace TBM ECU or SGW. Under certain conditions, SGW Module may take longer to establish Ethernet communication after boot up. If it takes longer than 30 seconds, The TBM2.0H module will set DTC U0080 - Ethernet Bus 1. As soon as SGW responds, the TBM2.0H will demature the DTC and move it to STORED. This issue should not cause any customer related symptoms. Do not replace the following TBM Part Numbers: WL: 68639445AF,68637489AE,68663479AE. WS: 68734941AA,68729188AC. EJ: 68592344AI. KM: 68592343AL,68735975AD. DT: 68634362AJ,68624784AF,68624784AE,68735493AB,68735493AA. DJ (HDCC): 68608721AJ. If the TBM2.0H module has set the DTC U0080 and it is STORED or ACTIVE, please clear the fault and do nothing. No further diagnostics is required. ---------------------------------------------------------------------------------------------------- TBM2.0H Setting DTC B1E21 Do Not Replace the TBM ECU. Is triggered when the TBM Backup Battery is discharged, inactive, or drained. This can happen during the lifetime of the vehicle. TBM should NOT be replace for B1E21, since there is no fault on TBM. TBM battery is replaceable. Part number of the back-up battery inside TBM is 68597650AA. Do not replace the following TBM Part Numbers: WL: 68639445A$, 68663479A$. ---------------------------------------------------------------------------------------------------------- TBM Setting DTC U0499-00 Please refer to SOL S268A000004 if you are attempting to replace or repair the telematics box due to DTC U0499-00. This DTC does not cause direct customer impact and cannot be cleared. Engineering is working on TBM software enhancements, tentative Q2 2026. Do not replace the following TBM Part Numbers: KM: 68592343A$
S2602000003
Clunk, Creaking, Squeaking, Knocking Noise From Front Suspension Over Bumps And Or Rough Road Conditions.
S268A000011
Radio Remains On After Ignition Off
08-134-26
Universal Garage Door Opener (UGDO) Inoperable Technicians may or may not find the following Diagnostic Trouble Code (DTC) present: SYMPTOM: ● B251D1-00 - Universal Garage Door Opener Control. Customers may comment on the following: ● Operational questions regarding the usage of the HomeLink® UGDO. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2608000015
Memory Seat Does Not Work There Is No Response from The Seat While Pressing the Memory Seat Profiles from the Switch Diagnostic Trouble Code (DTC) B1D9B-54- Seat Horizontal Front Stop Not Learned-Missing Calibration
08-011-26 REV.A
Flash: Global Telematics Box Module (TBM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **B1562-14 - GPS Antenna-Circuit Short To Ground Or Open. ● B1561-11 - Cellular Antenna 2-Circuit Short To Ground. ● B1560-11 - Cellular Antenna 1-Circuit Short To Ground.** ● B22A9-96 - ECU Internal Performance-Component Internal Failure. ● B1560-13 - Cellular Antenna 1-Circuit Open. ● B1561-13 - Cellular Antenna 2-Circuit Open. The customer may experience the following: ● Uconnect Box requires service message at start up on the display screen. This bulletin involves reprogramming the TBM with the latest available software.
9100261Rev1
Prior to windshield replacement for cracks (circular shape towards center of glass), please mark the area of concern, tape windshield over crack area, replace and ship original part to Stellantis per the retention policy. Please make sure your 3rd party glass replacement follows this request.
9100781
Issue: complaint of rattle from exhaust Before replacement: Check for loose exhaust Aluminum isolator brackets (check if the bracket is movable by hand/bolts not fully fastened to the vehicle). If loose, tighten and check to see if the rattle is still present. Check clearances between exhaust components and Aluminum isolator brackets, as well as other parts of the vehicle. If physical metal-to-metal contact is identified, loosen the clamps joining the catalytic-side and muffler-side systems and slide the muffler side exhaust back until the 4 small M&M sized bulges can be seen on the driver-side cat-side pipes. Take care not to damage the system, do not use a hammer to break the muffler side free. The muffler side exhaust should be pushed towards the front of the vehicle until the rim of the muffler side inlet pipe meets the edge of the bulges. Re-tighten and check for rattles again. If the rattle is still present, replace the system.
9100784
Prior to replacing an inoperative passive entry door handle, perform Star Online S2523000089.
S2523000070 REV.A
Central ADAS Decision Module (CADM) Diagnostic Trouble Codes C00C0-4A, C00C1-4A, C00C5-4A.
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2602000001
Service Electric Sway Bar Lamp On In Cluster. Diagnostic Trouble Code (DTC) C008E-00 In Auto Sway Bar (ASBS)
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
110592
SENSOR - PINCH
23-005-26
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: SYMPTOM: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2408000016 REV.D
Front Passenger and/or Rear Left and/or Rear Right Door Window Switches are Inoperative, Window Operation Works from the Driver Master Switch
110608
SPEAKER - NONE
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
110447
WATER PUMP
110448
WATER PUMP
08-075-26
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S228A000025 REV.A
Harman R1H Uconnect 5 Radio Software Flash Error Codes
S2423000027 REV.D
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
S2623000007
The Handsfree Kick Feature Does Not Work Or Works Intermittently.
9100591 Rev 1
Universal Garage Door Opener Prior to replacing the UGDO or sun visor, call HomeLink® Customer Care at 1-800-355-3515 for a proper evaluation of the issue. If this does not correct the issue, please follow the steps in SOL: S2508000039
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S268A000005
Front HDMI Port or Front Passenger Display Module (FPDM) Not Projecting Video
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
S2607000003
GMET4 DOHC Water Pump Coolant Leak Inspection
S2308000120 REV.F
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
109991
ISOLATOR - SPRING
109992
ISOLATOR - SPRING
109003
HOSE - SUNROOF DRAIN
S2607000002
Hemi Water Pump Coolant Leak Inspection
08-030-26
Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C14A1-74 - Unintended Actuator Shaft Movement Detected-actuator Slipping. Customers may comment on the following: ● The service 4WD light is on in the Instrument Panel Cluster (IPC). This bulletin involves inspecting and possibly reprogramming the DTCM with the latest available software.
S2523000089 REV.A
Passive Entry Exterior Door Handle Inoperative When Touched For Lock And Or Unlock.
08-014-26
Not applicable to vehicles built for US market. R1H Radio U40.20 USB Software Update - Korea Customers may experience one or more of the following: ● T-maps navigation feature is intermittently not available due to map loading. ● When the navigation speed alarm margin is set and the while driving the vehicle between the speed limit and the set margin, the navigation speed alarm will sound off continuously and the user is unable to control the volume. ● After setting a navigation destination and then the customer is following the navigation route, the navigation system will stop operating. ● Navigation touch screen menu is inoperable after setting a navigation destination. The home screen widget will be black and the navigation display map will no longer show the navigation route. ● WI-FI software update pop up is being triggered in non connected vehicles. ● Vehicle Forward Collision Warning must have two options: OFF / Warning + Active Braking. ● Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects Right Hand Drive RHD only. ● With ignition on and radio on, the radio display freezes then restarts (Rearview Camera (RVC) functions normally). ● Radio is taking more than one minute to start after starting the engine (RVC functions normally). ● System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode (RVC functions normally). This bulletin involves inspecting and if required, updating the radio software level to U40.20. Depending on the radio's current software level the radio may need a one or two USB update. M08 FSAR-RSU-6722 -2-
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
106356
BRACKET KIT - MOUNTING
08-012-26
Speaker Diagnostic Procedure Rattle, buzz and squeak coming from specific speakers.
S2308000120 REV.E
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
S2521000004 REV.B
The customer is experiencing a clicking or pop noise from the steering knuckle and bearing area during turns while driving.
08-011-26
Flash: Global Telematics Box Module (TBM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B22A9-96 - ECU Internal Performance-component Internal Failure. ● B1560-13 - Cellular Antenna 1-circuit Open. ● B1561-13 - Cellular Antenna 2-circuit Open. ● B1562-13 - GPS Antenna-circuit Open.** Customers may experience the following: ● Uconnect Box requires service message at start up. This bulletin involves reprogramming the TBM with the latest available software.
S2623000001
Rotary Shifter Lights Blinking, Shifter Not Moving, Not Going Into Gear.
S2623000002
Service Shifter Message On Instrument Cluster With Loss Of Communication Diagnostic Trouble Code (DTC) Related To The Shifter.
109231
LATCH - LIFTGATE
109232
LATCH - LIFTGATE
18-110-25
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. Customers may experience the following: ● During a start/stop event, the vehicle will go into 'Auto Park Mode This bulletin involves reprogramming the PCM with the latest available software.
S2521000004 Rev.A
Note: actual release date was 12/22/2025 The customer is experiencing a clicking or pop noise from the steering knuckle and bearing area during turns while driving.
109161
SWITCH - TRANSFER CASE, RIDE HEIGHT, TERRAIN SELECT
109011
VALVE BODY & CONTROL UNIT – TRANSMISSION
109157
ARMREST - REAR DOOR TRIM
S2521000005
The customer states the ABS and Traction Control warning comes on. Vehicle sets wheel speed BSCM/ABS fault codes.
9100227Rev3
Part Number is more precise than "Up to and Including" and "After" dates in the item description. Please ensure to order the correct CADM and Long Range Camera Part Number(s) the vehicle was built with. The Root of the Original and Replacement part should be identical, the difference will be in the NIK level. Technician Removal of the Long Range Camera and CADM for Testing Purposes: Please ensure the root of the Original and Replacement part are identical.
08-394-25 REV. A
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure.
9100446Rev4
BSR from the front suspension. Investigate the disconnecting stabilizer bar for a broken or cacked weld on the upper mount (anti rotation bracket). Instead of the replacing the whole stabilizer bar use Kit #PN#68730602AB. Refer to SOL #S22502000002 for additional information
S2508000107
Comfort Seat Module (CSM) or Comfort Steering Wheel Module (CSWM) do Not Operate
S2523000094
Power Liftgate Noise During Gate Operation
9100732
If the power liftgate exhibits operating noise during opening or closing but functions normally, follow these instructions: 1. Do NOT replace the Power liftgate if: -The liftgate opens and closes properly, and -The customer concern is only operating noise. 2. Replacement is ONLY recommended if: -There is an abnormal sound (e.g., grinding, scraping, knocking), -A functional issue exists (binding, stall, failure to open/close), -There is visible damage, or -Relevant DTCs are present. 3.If you hear grinding, scraping, or any abnormal sound, parts can be replaced. -Describe the issue clearly in the narrative. -If possible, record the sound and attach it to the narrative.
9100734
If the DTC B1E21-96: Backup Battery-Component Internal Failure is active and customer states Popup message will show at the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347
108946
EVAPORATOR - AIR CONDITIONING
108947
EVAPORATOR - AIR CONDITIONING
108974
THROTTLE BODY - NONE
08-394-25
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present echnicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure
108941
MODULE - STEERING CONTROL
108942
MODULE - STEERING CONTROL
S2521000006
Service 4WD light on in the cluster. C14A1-74 DTC will be present (Active or Stored).
S258A000021
Diagnostic Trouble Code (DTC) B15A1-00 Media Port Connection 1 Connection Found Set.
08-170-25 REV. A
Flash: Body Control Module (BCM) Updates Customers may experience one or more of the following: ● Battery drained. ● Ignition off draw. ● Instrument Panel Cluster (IPC) goes off and on when the vehicle goes into sleep mode. ● Door lock indicator lamps stay illuminated. This bulletin involves **inspecting and possibly** updating the BCM with the latest available software.
S2423000012 REV.D
Power Liftgate Is Inoperative or Won’t Close.
S2523000089
Passive Entry Exterior Door Handle Inoperative When Touched For Lock And Or Unlock.
S2523000065 REV.A
Diagnostic Trouble Code DTC(s) C1593-00, C2217-00, U0131-00. and Service Electric Power Steering Messages.
108473
LAMP – BACKUP, LAMP - TAIL
108499
LAMP – BACKUP, LAMP - TAIL
08-145-25 REV. A
Flash: Radio Frequency Hub Module (RFHM) Updates **Customers have experienced: ● Intermittent key fob detection. ● Possible dead batteries in key fobs. ● Proximity Wake-Up (welcome feature) does not activate at times. ● Key fob not detected when inside vehicle.** ● Uconnect app requests not functioning (lock/unlock, remote start functions). The following software enhancements are also included: ● DTCs B1A7D and B1A0A-00 robustness improvements. This bulletin involves updating the RFHM module with the latest available software.
S2308000034 REV.A
No Wireless Charging Or Slow Wireless Charging
S2521000004
The customer is experiencing a "clicking" noise during turns while driving on WL vehicles
S2508000100
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
9100715
WIRELESS CHARGING PAD OVERHEATING & INOP Do not replace wireless chargers before verifying these, 1. Does the customers Device have QI charging compatibility (supports Wireless charging)? (there are some phones not supporting wireless charging function) 2. Is the Device properly aligned for charging to initiate (also make sure that the Device does not slide/move easily while charging, causing the charging connection to break) 3. Check the backside of the phone if there is a metal plate/ring or accessory. It may block charging 4. Verify with the phone with no case if charging works well (case too thick, not QI certified case, case with accessories like a pop socket may cause not charging).
08-336-25 REV. B
Security Gateway Module (SGW) Software Update Customers may experience one or more of the following: ● Connectivity services will not work - including WIFI setup, Alexa, live traffic etc. Level 2 Plus functionality also affected/not enabling. ● SGW not responding to diagnostic and showing offline. ● Wifi cannot be setup. The following software enhancements are also available: ● Diagnostic Trouble Code (DTC) U3033-00 - Control Module Security Certificate Missing/Invalid and U3033-01 - Control Module Security Certificate Missing/Invalid - General Electrical Failure are both active or stored and cannot clear. This DTC will not turn on the Malfunction Indicator Light (MIL). ● If a Firmware Over The Air (FOTA) message appears specifically directing the customer to service OR repeated FOTA events are not being completed, then a manual flash is required for the SGW update. ● SGW module is not responding to diagnostics and is showing offline This bulletin involves inspecting and possibly updating the SGW to the latest software level in the case that the FOTA did not function.
9100437Rev1
The service shifter message comes on in the cluster and the lever gets stuck in park "P" and it can be present the follwoing DTC: - U11E3 - TCM Lost communication with ESM on D-PT CAN - U0103 - Lost communication with Electric Gear Shift Module - U0101- Lost communication with DTCM - U0418 - Implausible Data Received From Brake System Control Module - U0402 - Implausible data received from TCM **NOTE: Prior any shifter replacement Refer to TSB-21-016-25 2024-2025 WS - Valve Body Replacement. Recommended Diagnosis procedure: 1. Confirm if U0101 -Lost Communication with TCM or U0418 -Implausible Data Received From Brake System Control Module are present, if so check the Valve Body CAN Terminals any corrosion. 2. Check the wiring connectors between the ESM and the TCM and check voltage. 3. Check the pin header for the ESM for any bent pins. 4. If wiring and voltage are good and the DTCs (U11E3 - TCM Lost communication with ESM on D-PT CAN & U0103 - Lost communication with Electric Gear Shift Module) are still present, erase them with the scan tool. Reset ECU. 5. if DTCs for loss communication are still active at the ESM and you are still unable to shift then replace the Shifter module.
S2508000093
Instrument Panel Cluster (IPC) Displays “Service Tire Pressure System”, Tire Pressure Monitoring System (TPMS) Lamp is Flashing
08-336-25 REV. A
Security Gateway Module (SGW) Software Update Customers may experience **one or more of **the following: ● **Connectivity services will not work - including WIFI setup, Alexa, live traffic etc. Level 2 Plus functionality also affected/not enabling. ● SGW not responding to diagnostic and showing offline.** ● Wifi cannot be setup. The following software enhancements are also available: ● Diagnostic Trouble Code (DTC) U3033-00 - Control Module Security Certificate Missing/Invalid and **U3033-01 - Control Module Security Certificate Missing/Invalid - General Electrical Failure** are both active or stored and cannot clear. This DTC will not turn on the Malfunction Indicator Light (MIL). ● If a Firmware Over The Air (FOTA) message appears specifically directing the customer to service OR repeated FOTA events are not being completed, then a manual flash is required for the SGW update. ● SGW module is not responding to diagnostics and is showing offline. This bulletin involves **inspecting and possibly** flashing the SGW to the latest software level in the case that the FOTA did not function
S2509000009
Engine Oil Leak
S2508000091
Radio (ETM) Is Always Setting Stored DTC B15A1-00 Media Port 1 Connection
105646
MODULE - STEERING CONTROL & COLUMN
08-336-25
Security Gateway Module (SGW) Software Update *The following software enhancements are available: ● Update for Diagnostic Trouble Code (DTC) U3033-00 - Control Module Security Certificate Missing/Invalid. NOTE: This DTC will not turn on the Malfunction Indicator Light (MIL) but is active or stored and cannot clear. ● If a FOTA message appears specifically directing the customer to service OR repeated FOTA events are not being completed, then a manual flash is required for the SGW update. ● SGW is not responding to diagnostics and showing offline.* This bulletin involves flashing the SGW to the latest software level in the case that the FOTA did not function.
11-002-25 REV. A
Muffler Hanger Rattle Customers may experience the following: ● Exhaust rattle going over bumps and on rough roads. This bulletin involves inspecting the exhaust system and if necessary tightening or replacing one or both of the muffler hanger fasteners
S2522000003
Tire Pressure Monitor (TPM) Warning Lamp On Or Flashing. Sensor(s) Not Reading And Or Showing Dashes.
107450
TRANSMITTER - INTEGRATED KEY FOB
08-319-25
Flash: Amplifier (AMP) Diagnostic and System Updates Customers may experience the following: ● Droning noises coming out of the speakers at specific RPMs that range from 1200 to 1800 RPM. Probability of occurence is most likely during cold ambient temperatures. This bulletin involves updating the AMP with the latest available software.
S2505000008
C0044-00-BRAKE PRESSURE SENSOR 1 (MODULE, Brake System Control 2 (BSCM 2))
S2519000008 REV.A
Noise From Front End While Steering Or Turning The Steering Wheel.
S2523000079
Rear Door Mounted Window Switch Button Is Inoperative, Stuck, Or Switch Button Does Not Return To Original Position After Pushed.
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
9100671
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
S2524000009
Customer Indicates Air Conditioning Blows Warm.
9100549 Rev 3
WL/WS/LB Key fobs unable to be programmed at dealers. Please check current stock and verify a Blue "OK" mark on part label. Return all parts that do not have the blue "OK" marking to Mopar under RMA 8925-792 and replace with clean stock from Mopar. FOBs with no marking or a Green Check mark should also be returned.
OTHERDOC_149
Global Telematics Box Module Over The Air Update from R5C1 and R5O1 to R5T TBM2.H Software Version (FOTA) Customers may experience one or more of the following: - Error display of "Uconnect Box Requires Service" popups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ]. - TBM sleep mode not working causing battery drain in some cases. - Error display of "Uconnect Box Requires Service/Wifi Unavailable" pop ups; [ TBM DTC B22A9-96 Internal Performance Failure ].
03-007-25
Service 4WD Light Illuminated Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C1463-94 - Front Axle Disconnect Control-Unexpected Operation. Customers may experience one or more of the following: ● Service 4WD light is illuminated on the Instrument Panel Cluster (IPC). ● Unable to shift from two-wheel drive to four-wheel drive or four-wheel to two-wheel drive, it will stay in the current state This bulletin involves inspecting the serial number on the Front Axle Disconnect (FAD) housing to determine a build date and, if required, replacing the FAD assembly
08-286-25
Flash: Global Telematics Box Module (TBM) Updates The customer may experience the following: ● Uconnect Box requires service message at start up This bulletin involves reprogramming the TBM with the latest available software.
11-002-25
Muffler Hanger Rattle Customers may experience the following: ● Exhaust rattle going over bumps and on rough roads. This bulletin involves inspecting the exhaust system and if necessary tightening or replacing one or both of the muffler hanger fastener
S2408000118 REV.C
Vehicle Key FOB Functions for Passive Entry, Lock and Unlock, and Passive Keyless Go Starting Intermittently Do Not Operate
S2522000001
TPMS Handling & Installation Best Practices
S2522000002
Customer Indicates Tire Pressure Monitoring System (TPMS) Lights On Dash.
18-079-25
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P24B9 - Evap System Leak Detection Pump Pressure Sensor Circuit Range/Performance. ● P1CEA - Boost Side Evap Purge System Performance. Customers may experience the following: ● Check Engine warning lamp on in the Instrument Panel Cluster (IPC). This bulletin involves reprogramming the PCM with the latest available software.
21-016-25 REV. C
Valve Body Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U0101 - Lost Communication With The Transmission Control Module (TCM). ● U0402 - Implausible Data Received From TCM. ● U0418 - Implausible Data Received From Brake System Control Module 1. Customers may also comment on the following: ● Vehicle will go in limp-in mode. After the vehicle enters limp-in mode and has been shifted into Park, the vehicle will not shift into a forward or reverse gear This bulletin involves replacing the transmission valve body assembly.
9100646
False fails on PCR, DBSM and PDCs Stuck Closed or open diagnostics, DTC P2AF5 or P2AF6, leading to NTF and unnecessary replacements. Current controls are not robust against depleted auxiliary battery condition. Please follow SOL S2508000031.
S2223000074 REV.B
Power Side Steps Reverse, Stop In Motion, Do Not Deploy Or Stow, And May Have a Chirp Noise.
S2408000079 REV.A
Liftgate Lock Button Inoperative, Cluster Message “Service Keyless System”
S258A000019
Radio Does Not Turn On Automatically When Vehicle Is Started
21-016-25 REV. B
Valve Body Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U0101 - Lost Communication With The Transmission Control Module (TCM). ● U0402 - Implausible Data Received From TCM. ● U0418 - Implausible Data Received From Brake System Control Module 1. Customers may also comment on the following: ● Vehicle will go in limp-in mode. After the vehicle enters limp-in mode and has been shifted into Park, the vehicle will not shift into a forward or reverse gear. This bulletin involves replacing the transmission valve body assembly.
S2508000064
Album Cover Art Flickers On Cluster Audio Page
9100641
Symptoms/Condition: Shifter reports loss communication AND NO OTHER MODULES report the condition. Diagnostic: Please make sure ONLY shifter reports loss communication. If there are other modules reporting loss communication, then follow the existing service procedure Repair Procedure: 1. Verify Complaint - ESM reports a Loss of Communication (LOC) DTC, but no other modules do. - If multiple modules report the same LOC, the ESM is not the cause (its not a gateway module). 2. Read DTCs - Relevant codes: U0101, U0140, U0155, U0129, U11C3, U0402, U0422, U0423, U0415, U145D. - If multiple LOC DTCs are present: a. Check battery health, system voltage, and TCM (including valve body). b. If TCM goes offline, ESM may falsely report LOC DTCs. 3. Check Environmental Data - Look for voltage/system issues at the same mileage. a. If DTCs clear, do not replace ESM. b. If not, inspect: b.1 Module connectors/pins: If damaged, dont repair shifter. b.2 TCM connectors/pins: Same rule. b.3 AGSM connectors/pins: If damaged, repair shifter. b.4 AGSM wiring harness: If damaged, dont repair shifter. 4. Review Past Service - Confirm battery and TCM-related repairs are still effective. a. If not, fix and clear DTCs. b. If yes, continue. 5. Check for Other LOCs - If other modules report LOC to the same module, inspect that module. - If not, repair the AGSM. Additional Description: - The ESM only communicates with the TCM and is fully controlled by it. - In non-combustion engines, the TCM is replaced by the PCM. - If a stored DTC in the ESM disappears and doest return, do not replace the ESM.
S2108000236 REV.B
Windshield HUD (Head Up Display) Display Features
S258A000017
Door speaker Inoperative or No Sound
S2408000118 REV.B
Vehicle Key FOB Functions for Passive Entry, Lock and Unlock, and Passive Keyless Go Starting Intermittently Do Not Operate
106343
HEADREST - SECOND ROW
S2509000001 REV.B
Engine Rattle Noise
106320
Warranty Newsletter – Volume 11, Issue 7
106321
FCA Caribbean Warranty Newsletter – Volume 11, Issue 7
23-006-25 REV. B
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield.
S2523000072
Central ADAS Decision Module (CADM), Long Range Camera Front (LRCF), Advanced Driver Assist System (ADAS). AEB ACC FCW Message On Cluster.
S2422000001 REV.D
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
08-220-25
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S2523000061 REV.A
Blind Spot Mirror Warning Inoperative Or Intermittently Inoperative. Service Blind Spot Message In Cluster.
S2523000070
Central ADAS Decision Module (CADM) Diagnostic Trouble Codes C00C0-4A, C00C1-4A, C00C5-4A.
09-019-25
Make Up Air Hose Disconnected Customers may experience the following● A deterioration in engine performance. This bulletin involves inspecting the Make Up Air Hose and, if needed, reconnecting the hose to the resonator.
105648
MODULE - ENGINE CONTROLLER
S2519000006
Steering Repair Information Involving Toe Angle. Tie Rod And Or Electric Power Steering (EPS) Units.
S2408000126 REV.A
Diagnostic Trouble Code (DTC) B1A0A-00 Remote Keyless Entry (RKE) FOB 3 Performance
S2508000057
Night Vision Field Of View Limited And No Option To Overlay Analog Gauges
05-002-25
Front Caliper Bolts Loose Customers may comment on the following: ● A noise coming from the front of the vehicle. This bulletin involves tightening both front brake caliper bolts to specification.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2219000005 REV.D
Check Engine Lamp On. Warning Messages in the Cluster. U0131 Lost Communication with Power Steering Control Module Set.
S2523000065
Diagnostic Trouble Code DTC(s) C1593-00, C2217-00, U0131-00. and Service Electric Power Steering Messages.
9100622
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
105288
VALVE - CHECK
9100615
Power brake booster To avoid potential charge-back, only use MOPAR approved brake fluid per the service manual. When filling the brake reservoir, use clean equipment and gloves during repair to avoid cross-contamination.
S2523000061
Blind Spot Mirror Warning Inoperative Or Intermittently Inoperative. Service Blind Spot Message In Cluster.
S2524000007
Customer Indicates At Key Off The Display Screen Shows A Box For Front And Rear Blower Speed
9100549REV1
Keyfob WL/WS/LB Key fobs unable to be programmed at dealers. Please check current stock and verify a Blue "OK" mark on part label. If not present send part back to Mopar under RMA 8925-792 and replace with clean stock from Mopar. Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern.
9100611
Radio Frequency Hub Module 25MY WL/WS built starting week of 6/9/25 may show up at dealerships with a message in cluster saying "key fob left vehicle" and while in RUN the vehicle may exhibit horn chips as if the fobs did leave even though they are still in the cabin. This is a known issue that is under investigation but will go away after the vehicle is brought out of shipping mode and into logistics.
105590
Warranty Newsletter – Volume 11, Issue 6
105591
FCA Caribbean Warranty Newsletter – Volume 11, Issue 6
S2523000054
Intermittent Vibration Buzz Squeak Rattle (BSR) Shaking Felt In Steering Wheel.
105289
TRANSMITTER - INTEGRATED KEY FOB
S2519000004
Steering Wheel Off Center. Customer Complaint/Technician Observation: Customer may state the vehicle drives straight but the steering wheel is off center. They may also describe the condition as a pull or a lead due to them trying to keep the steering wheel centered. Discussion: Drive on both highway and city roads if possible. If equipped with air suspension, place the vehicle in normal ride height (NRH). Refer to Service Library 02 - Front Suspension / Wheel Alignment / Diagnosis and Testing for a list of conditions, possible causes and corrections.
S2519000004REVA
Steering Wheel Off Center. Customer Complaint/Technician Observation: Customer may state the vehicle drives straight but the steering wheel is off center. They may also describe the condition as a pull or a lead due to them trying to keep the steering wheel centered. Discussion: Drive on both highway and city roads if possible. If equipped with air suspension, place the vehicle in normal ride height (NRH). Refer to Service Library 02 - Front Suspension / Wheel Alignment / Diagnosis and Testing for a list of conditions, possible causes and corrections.
9100599
Underhood start/stop safety The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.
9100600
Switch - Power Window Before replacing the Window Switches (Termination AB Only), please follow these steps: 1.- Make sure all the switches are properly connected, disconnect the switch and reconnect it. 2.- In case the passenger/rear window switches are not working please, cycle the Door lock/Unlock Switches of the respective Switch (Lock and Unlock the doors at least 3 times) and try to roll the windows up and down. 3.- Check for what DTC are detected and take proper steps to diagnose the DTC's. if there are no DTC's then window switches can't be replaced.
08-170-25
Flash: Body Control Module (BCM) Updates Customers may experience one or more of the following: ● Battery drained. ● Ignition off draw. ● Instrument Panel Cluster (IPC) goes off and on when the vehicle goes into sleep mode. ● Door lock indicator lamps stay illuminated. This bulletin involves updating the BCM with the latest available software.
9100594
Front Door Interior Panels: Warped Interior Door Panel / Broken Panel / Door Panel Not Fully Seated Observation: Would observe that the interior door panel is not properly seated or attached. Panel(s) may appear warped or out of position in some areas. No signs of damage should be expected. How to diagnose: Visually inspect the door panel(s) for proper installation and check for the presence of broken or loose clips. Remove the panel and inspect clips and clip towers. Next step would be reinstalling the panel if visual inspection does not find any issues. Repair Procedure: Require a picture of the door panel(s) in the 'as found' condition so we can understand what warped means in the claims that are being created. After, check the door panel for proper installation and for the presence of broken or loose clips. Remove the panel, following normal servicing procedure, and inspect clips and clip towers. If any clips are broken or missing, replace prior to reinstalling original door. After confirmation that no loose/broken/damaged clips and/or clip towers, and reinstalling door panels does not correct issue, then a 'front door trim panel' kit / claim would be acceptable. In this case, Stellantis would like to request the panel back. How to validate fix: Verify that door has no loose/broken/damaged clips and/or clip towers. Replace any broken/missing clips where possible. Then validate that reinstalling the interior door panel addresses initial issue made within the claim.
9100595
Front Door Interior Panels: Warped Interior Door Panel / Broken Panel / Door Panel Not Fully Seated Observation: Would observe that the interior door panel is not properly seated or attached. Panel(s) may appear warped or out of position in some areas. No signs of damage should be expected. How to diagnose: Visually inspect the door panel(s) for proper installation and check for the presence of broken or loose clips. Remove the panel and inspect clips and clip towers. Next step would be reinstalling the panel if visual inspection does not find any issues. Repair Procedure: Require a picture of the door panel(s) in the 'as found' condition so we can understand what warped means in the claims that are being created. After, check the door panel for proper installation and for the presence of broken or loose clips. Remove the panel, following normal servicing procedure, and inspect clips and clip towers. If any clips are broken or missing, replace prior to reinstalling original door. After confirmation that no loose/broken/damaged clips and/or clip towers, and reinstalling door panels does not correct issue, then a 'front door trim panel' kit / claim would be acceptable. In this case, Stellantis would like to request the panel back. How to validate fix: Verify that door has no loose/broken/damaged clips and/or clip towers. Replace any broken/missing clips where possible. Then validate that reinstalling the interior door panel addresses initial issue made within the claim.
02-002-25
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
09-011-25
Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise.
21-016-25 REV. A
Valve Body Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U0101 - Lost Communication With The Transmission Control Module (TCM). ● U0402 - Implausible Data Received From TCM. ● U0418 - Implausible Data Received From Brake System Control Module 1. Customers may also comment on the following: ● Vehicle will go in limp-in mode. After the vehicle enters limp-in mode and has been shifted into Park, the vehicle will not shift into a forward or reverse gear This bulletin involves replacing the transmission valve body assembly.
S2508000039
Universal Garage Door Opener (UGDO) Inoperative, LED Indicator Lamps Not Illuminating
S2308000120 REV.D
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
S2519000003
Slight Pull, Drift, Wander. Lack Of Precise Steering.
104686
BOLT - HEX FLANGE HEAD
S2523000032 REV.A
Steering Dragging While Recreational Flat Towing Behind RV.
08-145-25
Flash: Radio Frequency Hub Module (RFHM) Updates Customers must experience the following: ● Uconnect app requests not functioning (lock/unlock, remote start functions). This bulletin involves inspecting and possibly updating the RFHM module with the latest available software.
S2523000043
Glasses Compartment Of The Overhead Console Will Not Open Or Close.
S2523000046
Check Engine Lamp On. Diagnostic Trouble Code (DTC) P1D73 And Or P05AE For Active Grill Shutter (AGS).
104683
CARPET - REAR FLOOR
9100569
Video Routing Module Verify Z part number availability. Order a Z part number for all Exchange Orders: Warranty, Mopar, customer pay and service contract. Order regular part number for New, Unsold units only. Please review the latest version of SOL S2208000030 regarding DVD/blue ray issues. After updating software perform resets on both display or concern may still appear. After Battery Drainage VRM do not work. Please follow the following steps. 1. Check VRM proxi, if the VRM is not aligned, perform proxi alignment, reset module. 2. If proxi is correct, reset module 3. Check for DTCs, and check wiring and components related to those DTCs and clear them.
S2508000033
The Instrument Panel Cluster (IPC) Displays “Wipe Sensor” Message
S2523000040
Center Console Armrest Lid Does Not Stay Open, Feels Loose, Does Not Latch.
S2523000036
Sunroof Inoperative, Not Moving To Open Or Closed Positions.
S2108000241 REV.B
No Crank, No Start, Start Stop Inoperative
S2308000120 REV.C
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
S2523000034
C008E-00 Setting After Windshield Replacement
S2508000029
Instrument Panel Cluster (IPC) Message “Park Assist System Unavailable” or “Service Park Assist System”, “Rear Braking Assist Unavailable” or “Service Rear Braking Assist System" with Performance Diagnostic Trouble Codes (DTCs)
S2523000032
Steering Dragging While Recreational Flat Towing Behind RV.
S258A000013
AM Radio Static, With No Active or Stored Radio Antenna Diagnostic Trouble Codes (DTC).
9100549
Keyfob WL/WS/LB Key fobs unable to be programmed at dealers. Please check current stock and verify a green check mark on part label. If not present send part back to Mopar under RMA 8925-792 and replace with clean stock from Mopar. Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern.
104558
FCA Caribbean Warranty Newsletter – Volume 11, Issue 4
9100475
Key Fob Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern.
S2508000028
Cluster Off-Road Pages Have A Delay In Updating Graphics And Data
08-111-25
Right Front Heated Seat Inoperative Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E9A - Front Right Heater Control 1 – Circuit Open. Customers may experience the following: ● Right front heated seat will not activate or will shut off after a few seconds. This bulletin involves inspecting and possibly repairing the heated seat harness connector
104557
Warranty Newsletter – Volume 11, Issue 4
S2523000023
Trailer Tow Lights Inoperative. Diagnostic Trouble Codes (DTCs) B166E-13 B17AD-13 May Be Set.
104179
MODULE - IGNITION
S2509000004
Misfire DTCs, Rough Idle, Valvetrain Noise
S2523000010 REV.A
Exterior Rear View Mirror Stained And Will Not Clean.
104180
TRANSMITTER KIT & KEY KIT - INTEGRATED KEY FOB
9100531
2nd row seat frame 2nd Row Seat is hard to put back In position after moving it forward to access the 3rd row seat. Add grease as noted in the SOL publication S2423000041
S2508000014 REV.B
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
S2509000001 REV.A
Engine Rattle Noise
9100532
MODULE Steering Control Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced.
9100522
Ebooster When replacing the brake ebooster under warranty. Please return all associated parts which includes the snap rings so that the parts can be review by engineering.
103953
VALVE - OIL CONTROL
S2508000020
Odometer Blinking, Security Gateway (SGW) Diagnostic Trouble Codes (DTCs) Diagnostics
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
S2508000008 REV.C
Battery Drained, Ignition Off Draw (IOD), Cluster Display Goes Off and On, and/or Door Lock Indicator Lamps Stay Illuminated
S2508000014 REV.A
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
S2508000008 REV.B
Battery Drained, Ignition Off Draw (IOD), Cluster Display Goes Off and On, and/or Door Lock Indicator Lamps Stay Illuminated
9100502
LOWER ACTIVE GRILL SHUTTER If the upper or lower AGS seems to be inop please make sure you CLEAR the DTCs BEFORE swapping the old AGS for a new one, and test if the error code returns. Very often the wiring harness presents corrosion, so make sure to check it for any damage BEFORE swapping the AGS. Corrosion in the harness disrupts communication with the AGS, which sets up the DTCs for AGS performance and lights the CEL. If the AGS is inop and it will be replaced and sent back to Stellantis also send back the wiring harness with it. Make sure to fully perform the PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE as indicated in the service library.
S2509000002
Engine Noise
S258A000007
Radio Display Screen Flicker
S258A000009
Apple CarPlay Does Not Complete The First Initial Wireless Connection.
S2123000084 REV.A
1st Row Seat Belt Retractor D-Ring Is Binding And Not Able To Rotate
S2423000008 REV.A
SOS Button Inoperative And Or Unavailable. B1552-2A Code Set.
S2423000034 REV.A
Defroster Grille Has Gaps And Or Is Not Sitting Flush.
S2513000001
Grille molding applique is sticking out at the headlamp
S2523000016
Replacement Exterior Mirror Glass Connector Does Not Match For Blind Spot.
103474
VALVE BODY & CONTROL UNIT - TRANSMISSION
103475
VALVE BODY & CONTROL UNIT - TRANSMISSION
S2108000015 REV.J
Uconnect Box Require Service Message
S2523000011
Exterior Mirror Blind Spot LED Indicator Inoperative Or Will Not Turn Off. Diagnostic Trouble Code (DTC) B285F-11 And Or B285F-15 Set.
9100500
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
S2223000074 REV.A
Exterior Power Fold Mirror Does Not Travel To Full Extend or Fold Positions.
S2523000010
Exterior Rear View Mirror Stained And Will Not Clean.
08-037-25
Droning Humming Growling Noise Customers may comment on the following: ● Droning, humming or growling noises while in drive, park or neutral. This condition might disappear if the door is opened or a window is lowered down or when covering the Active Noise Cancellation (ANC) microphones This bulletin involves performing a PROXI Configuration Alignment.
S2509000001
Engine Rattle Noise
09-003-25
Oil Leaking From Oil Filter Area Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: ● Oil found on the ground beneath the vehicle.
23-008-25
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S2219000005 REV.C
Check Engine Lamp On. Warning Messages In The Cluster. U0131 Lost Communication With Power Steering Control Module Set.
9100446
Frt Stabilizer assembly BSR from the front end due to Smartbar (disconnecting front sway bar). Root cause was identified as anti-rotation bracket (connects the actuator to the stabar) coming loose due to inadequate clamp load at the joint and weld (holds the bolt shaft and bracket flange) was poorly designed. If any vehicle causes BSR because of this Bracket failure (loose joint/ bracket bends) DO NOT replace whole stabar assembly, instead replace with the service kit (PN#68730602AA). Dealer must need to order the parts from part ordering system for this claim. This kit contains 1 bracket (PN 68730603AA), 3 M10 Nut (PN 68730605AA), 2 M8X1.5 Bolt (PN 68730606AA) and 2 M10X1.5 bolt (PN 06513427AA). 1 M10 Bolt (PN 68730607AA). This kit will also contain a new torque instruction for the bolt which holds the clamp bracket to this failed anti-rotation bracket. DO NOT apply the old torque (45+/5Nm Direct torque). The new torque is Angle controlled torque monitor (20Nm Snug torque, 110 deg Angle, monitor torque within 40-70Nm). Please use Service Library for your reference.
9100446 Rev 3
Frt Stabilizer assembly(smartbar) BSR from the front end due to Smartbar (disconnecting front sway bar). Root cause was identified as anti-rotation bracket (connects the actuator to the stabar) coming loose due to inadequate clamp load at the joint and weld (holds the bolt shaft and bracket flange) was poorly designed. If any vehicle causes BSR because of this Bracket failure (loose joint/ bracket bends) DO NOT replace whole stabar assembly, instead replace with the service kit (PN#68730602AA). Dealer must need to order the parts from part ordering system for this claim. This kit contains 1 bracket (PN 68730603AA), 3 M10 Nut (PN 68730605AA), 2 M8X1.5 Bolt (PN 68730606AA) and 2 M10X1.5 bolt (PN 06513427AA). 1 M10 Bolt (PN 68730607AA). This kit will also contain a new torque instruction for the bolt which holds the clamp bracket to this failed anti-rotation bracket. DO NOT apply the old torque (45+/5Nm Direct torque). The new torque is Angle controlled torque monitor (20Nm Snug torque, 110 deg Angle, monitor torque within 40-70Nm). Please use Service Library for your reference.
S228A000005 REV.E
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
S2503000001
Service 4WD Message, Diagnostic Trouble Codes (DTCs) C1463-94 Front Axle Disconnect Control-Unexpected Operation, and/or C1463-92 Front Axle Disconnect-Performance or Incorrect Operation, Set.
S2503000002
Service 4WD Message Illuminated. Diagnostic Trouble Code (DTC) C1477-98 Transfer Case Clutch Component Or System Over Temperature, Set.
S2508000014
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
102939
LATCH – FRONT & REAR DOOR
103228
SENSOR - BATTERY
S258A000004
DVD Or Blu-Ray INOP, Rear Screens Or Monitors INOP, VRM Audio INOP, Mirroring INOP
102934
THROTTLE BODY
08-009-25
Flash: Battery Pack Control Module (BPCM) Diagnostic and System Update Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance This bulletin involves updating the BPCM with the latest available software
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
08-017-25
Driver Door Seat Massage Switch Inoperative Customers may comment on the following: ● The seat massage switch located on the driver door does not work. (Seat massage system still operates via the radio) This bulletin involves inspecting the left front door seat massage switch operation and possibly replacing the left front door wiring harness.
S2523000006
Buzz Squeak Rattle (BSR) Noise At Idle.
S2523000003
Door Latch, Handle And Ajar Additional Service Information.
9100478
PUMP KIT Transmission oil if replacing PHEV Electric Oil Pump for an electrical DTC - do not replace pan and filter as part of repair. The pump is available on its own. Pan and filter replacement are not necessary.
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2408000126
Diagnostic Trouble Code (DTC) B1A0A-00 Remote Keyless Entry (RKE) FOB 3 Performance
101790
BUCKLE ASSY - BUCKLE ASSYS/BELT
9100468
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
102365
Warranty Newsletter – Volume 10, Issue 11
102366
FCA Caribbean Warranty Newsletter – Volume 10, Issue 11
S2403000004 REV.A
Tapping, Knocking Type Noise/Vibration While Driving.
S2102000004 REV.B
WL Front Control Arm Bushing - Handling Link Has Loose Rubber Appearance
S2302000001 REV. A
Service Air Suspension Message In Cluster. Ride Height Sensor and System Performance Diagnostic Trouble Code(s) (DTCs) In Below Freezing Temperatures.
S2402000002
Click Or Clicking Noise From Under Hood Near The Fast Down Leveling Valve.
S2423000012 REV.C
Power Liftgate Is Inoperative or Won’t Close.
S2408000119
Instrument Panel Cluster (IPC) message “Night Vision Unavailable Service Required” or Loss of Night Vision
9100437
SHIFTER The service shifter message comes on in the cluster and the lever gets stuck in park "P" and it can be present the follwoing DTC: - U11E3 - TCM Lost communication with ESM on D-PT CAN - U0103 - Lost communication with Electric Gear Shift Module - U0101- Lost communication with DTCM - U0418 - Implausible Data Received From Brake System Control Module - U0402 - Implausible data received from TCM **NOTE: Prior any shifter replacement Refer to TSB-4582 2024-2025 WS - Valve Body Replacement. Recomended Diagnosis procedure: 1. Confirm if U0101 -Lost Communication with TCM or U0418 -Implausible Data Received From Brake System Control Module are present, if so check the Valve Body CAN Terminals any corrosion. 2. Check the wiring connectors between the ESM and the TCM and check voltage. 3. Check the pin header for the ESM for any bent pins. 4. If wiring and voltage are good and the DTCs (U11E3 - TCM Lost communication with ESM on D-PT CAN & U0103 - Lost communication with Electric Gear Shift Module) are still present, erase them with the scan tool. Reset ECU. 5. if DTCs for loss communication are still active at the ESM and you are still unable to shift then replace the Shifter module.
S2422000001 REV.C
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
101095
Bracket - Fender Mounting
101009
FAN MODULE - RADIATOR COOLING
S2403000004
Tapping, Knocking Type Noise/Vibration While Driving.
S2408000112
Blind Spot Warning Message Displayed on the Cluster
9100420
6x9 inch Before replacing a speaker part for crackles or rattling noises make sure to take the following steps: 1. Check for electrical harness routing too close to speaker's rear moving parts, improper connection, and/or harness pinch or damage. 2. Ensure no loose components, including trim grilles, fasteners, surrounding IP parts, etc. were found when removing the speaker. 3. Try "bad" speaker at another IP location and see if noise follows speaker. Try a different "good" speaker at "bad speaker location" and see if noise still happens at "bad" location. 4. Remove the bad speaker and replace it back. 5. If even with this verification and adjustments the speaker sounds bad, test the individual speaker with the audio files provided in the Service Library Homepage under "Reference Materials" prior to replacement. Follow all these steps, if issue still happens; reach out to the engineer at Stellantis for more support, if the engineer doesn t respond in 30 minutes. Then the speaker can be replaced
S2423000041 REV.A
2nd Row Seat Is Hard To Put Back In Position After Moving It Forward To Access The 3rd row seat.
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
S2423000041
2 nd Row Seat Is Hard To Put Back In Position After Moving It Forward To Access The 3rd row seat.
S248A000013
After Radio Software Update, Pedestrian Emergency Brake (PEB) Lamp and Forward Collision Warning (FCW) Lamp on in Cluster or Other Customer Programable Features Concerns Not Set, No Diagnostic Trouble Codes (DTCs)
S2108000249 REV.C
Cluster and Radio Display Settings Revert Back to Default Settings, Auto Door Locks and Paddle Shifter Inoperative With No Menu to Enable, Pedestrian Emergency Brake (PEB) Lamp and Forward Collision Warning (FCW) Lamp on After a Recent Service Repair no Diagnostic Trouble Codes (DTCs)
S2408000086
Central ADAS Decision Module (CADM) Low-Level / CADM Mid-Level / (CADM2), Driver Monitoring System Module (DMSM), Global Navigation Motion Module (GNMM), Long Range Camera Front (LRCF), Long Range Radar Front (LRRF), Mid-Range (Corner) Radar(s) (MRR), Advanced Driver Assist System (ADAS), Loss of ADAS Features, Lane Assist Inoperative, Service Active Lane Management Message
S2423000036
Third Row Upper Seat Back Handle Inoperative And Or Cables Disconnected.
99500
CARRIER – PLANETARY & SHAFT KIT - OUTPUT
S2408000079
Low Battery, No Crank No Start, Cluster Message “Service Keyless System”, Intermittent Power Liftgate Operation
S2408000076
Malfunction Indicator Lamp on, Diagnostic Trouble Code (DTC) P0EDD-00 – Hybrid/EV battery Pack B Deterioration
S2408000071
Power Liftgate Inoperative After servicing the Vehicle for a Low Battery Condition
S2423000034
Defroster Grille Has Gaps And Or Is Not Sitting Flush.
S2408000068
Multiple Modules Setting Low Battery Voltage, Instrument Panel Cluster (IPC) Setting B210A-00 System Voltage Low
S2408000066
Drained Battery, Low System Voltage, Battery Not Charging, High System Voltage
S2408000067
The Electronic Vehicle Information Center (EVIC) Displays Park Assist System Disabled Message
98628
ARM - LOWER CONTROL
98930
ARM - LOWER CONTROL
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2308000120 REV.B
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.