Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2524000012
High Voltage Air Conditioning Refrigerant Dye
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
9100624
Verify Reman part number availability. Order the "R" part number for all orders:
09-010-25
2.4L Excessive Oil Consumption XS1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
09-018-24
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.E
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
1000123
Air Bag Warning Lamp Illumination Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.
2310423
Front Side Window Contour Seal Deformation One or both front door side window seals are deformed Fig. 1. This bulletin involves replacing the window seal and glass.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
0900323
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ? Oil pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
09-003-23
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: Oil pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
88806
Warranty Bulletin D-23-01 - (XB1) 2.4L Engine ? Select 2014 - 2019 Jeep Cherokee (KL), 2017 - 2018 Jeep Compass (MP), 2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
09-013-22
2.4L Engine Oil Consumption Test The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S1708000118
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S1708000118 RevB
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
CSNW20
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W20
Powertrain Control Module.
W84
Customer Satisfaction Notification W84 Powertrain Software Update
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
18-043-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F - ETC Self-Learning Failure. P1524 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P0000-00 - Will be displayed in the scan tool, but should really be displaying P0326-00 (Knock Sensor 1 Circuit Performance). In addition, the customer may notice the following condition:After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(EMEA only). Hard start condition caused by spark plugs fouling. A ticking noise coming from the top of the engine area. The ticking noise is heard particularly at idle(EMEA and APAC only).
1804321
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F - ETC Self-Learning Failure. P1524 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P0000-00 - Will be displayed in the scan tool, but should really be displaying P0326-00 (Knock Sensor 1 Circuit Performance). In addition, the customer may notice the following condition:After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(EMEA only). Hard start condition caused by spark plugs fouling. A ticking noise coming from the top of the engine area. The ticking noise is heard particularly at idle(EMEA and APAC only).
08-064-21
Flash: Radio Frequency Hub Module (RFHM) Enhancements This bulletin involves reprogramming the RFHM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure (Software has been updated to better address this DTC). In addition, the customer may notice the following condition(s): Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64. With the ignition in the run position and the engine not running, the vehicle may not turn itself off after 30 minutes. Doors may not unlock when using the Remote Keyless Entry (RKE) Fob.(2015 only) Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality.(2015-2016 only) After an engine start and the doors are closed, a message in the cluster may be displayed ?Key Not Detected? when the key is actually present.(2015-2016 only) Only a message is displayed, the vehicle will start.
0806421
Flash: Radio Frequency Hub Module (RFHM) Enhancements This bulletin involves reprogramming the RFHM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure (Software has been updated to better address this DTC). In addition, the customer may notice the following condition(s): Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64. With the ignition in the run position and the engine not running, the vehicle may not turn itself off after 30 minutes. Doors may not unlock when using the Remote Keyless Entry (RKE) Fob.(2015 only) Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality.(2015-2016 only) After an engine start and the doors are closed, a message in the cluster may be displayed ?Key Not Detected? when the key is actually present.(2015-2016 only) Only a message is displayed, the vehicle will start.
W20 Combo Phase4
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W84 Combo Phase3
Customer Satisfaction Notification W84 Powertrain Software Update
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Customer complaint may include engine oil leak/consumption.
08-027-21
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.
0802721
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.
W80 Combo Phase2
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 2)
W80A
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 2)
W20 Combo Phase3
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module (Revision 2)
W80
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 1)
W84 Combo Phase2
Customer Satisfaction Notification W84 Powertrain Software Update
S2108000027
CEL, Check Engine Lamp On, DTC P0339 Crankshaft Position Sensor Intermittent
W20 Combo Phase2
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W84 Combo Phase1
Customer Satisfaction Notification W84 Powertrain Software Update
W80 Combo Phase1
Customer Satisfaction Notification W80 Oil Consumption Inspection
S1908000028 Rev.
(Rev. A) Power Inverter Load Ratings
S1908000102
(Rev. A) Power Inverter Load Ratings
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100220
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S1823000026 Rev.
(Revision A) MySky Rough Operation Or Sticks Open
S1823000026RevA
(Revision A) MySky Rough Operation Or Sticks Open
18-055-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U0402 - Implausible Data Received From TCM. P1DD2 - Torque Request Signal From TCM Denied. U1424 - Implausible Engine Torque Signal Received. P0101 - Mass Air Flow Sensor "A" Circuit Performance. U0418 - Invalid Data Received From Brake System Control Module. P0128 - Thermostat Rationality. P0703 - Brake Switch 2 Performance. P1185 - General Pressure Sensor Correlation. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. Customers may also experience the following:Vehicle periodically may fail to start(ED6 engine only). In addition, the following software enhancements are available:Changes which allow the catalytic convertor to operate cooler. Multiair solenoid electrical opening change to resolve idle tick/tap issue. Cruise control enhancements.
1805520
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U0402 - Implausible Data Received From TCM. P1DD2 - Torque Request Signal From TCM Denied. U1424 - Implausible Engine Torque Signal Received. P0101 - Mass Air Flow Sensor "A" Circuit Performance. U0418 - Invalid Data Received From Brake System Control Module. P0128 - Thermostat Rationality. P0703 - Brake Switch 2 Performance. P1185 - General Pressure Sensor Correlation. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. Customers may also experience the following:Vehicle periodically may fail to start(ED6 engine only). In addition, the following software enhancements are available:Changes which allow the catalytic convertor to operate cooler. Multiair solenoid electrical opening change to resolve idle tick/tap issue. Cruise control enhancements.
S1508000374
Keys/Fobiks, Programming Keys With High Line BCM (L3 BCM)
S1508000380
Keys/Fobiks, Programming Keys With Base Vehicle BCM (L2 BCM)
09-010-20
Engine Oil Vapor Inlet Tube Modification - P2173-00 - Air Leakage In Manifold (Signal Compare Failure) This bulletin involves installing a modified oil vapor inlet tube. The customer may describe a loss in vehicle performance (engine jerking or limp mode) and/or a malfunction indicator light (MIL) illuminated.The following Diagnostic Trouble Code (DTC):P2173-00 - Air Leakage In Manifold (Signal Compare Failure).
0901020
Engine Oil Vapor Inlet Tube Modification - P2173-00 - Air Leakage In Manifold (Signal Compare Failure) This bulletin involves installing a modified oil vapor inlet tube. The customer may describe a loss in vehicle performance (engine jerking or limp mode) and/or a malfunction indicator light (MIL) illuminated.The following Diagnostic Trouble Code (DTC):P2173-00 - Air Leakage In Manifold (Signal Compare Failure).
09-006-20 REV. B
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
0900620
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
S1721000016
Service 4wd Light On, Message AWD System Service Required
S2008000077
VP2R Radio Clock Not Keeping Time
09-006-20 REV. A
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
09-006-20
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
23-015-20
Disinfectant Solution Recommended for COVID-19
S1808000069
Intermittent Remote Start, Inhibit-Disable List
S1508000235
No Scan Tool Communication, Dominant Module Terminating Resistor Module Locations, BUS Circuit Terminal Testing Locations At The DLC (Diagnostic Link Connector) And BUS Test Values At DLC
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
18-030-20
Flash: Powertrain Diagnostic and System Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.
S2008000020
No Start, No Crank After PCM And RFHUB Replaced, DTC P0513 Invalid Skim Key Sets In The PCM
08-030-20 REV. A
Flash: Body Control Module (BCM) Enhancements This bulletin involves reprogramming the BCM with the latest available software. The customer may describe the following:After starting the vehicle with remote start, the engine stops when the doors are unlocked.
09-004-20
No Weep Hole In Muffler Assembly This bulletin involves drilling a weep hole in the muffler assembly. The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.
08-027-20
2.4L Ignition Coil Boot Replacement This bulletin involves replacing all four ignition coil insulating boots. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.
S2008000013
Key Programming, Security Pin Request, Pin Invalid
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
08-111-19 REV. A
RA3 and RA4 GPS Calibration Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
9004172
ROTOR, Brake, Rear Counter bore hole on the original rotor is used during production to locate the rotor during assembly, it is not required for service. 2AMV8043A$ can be used for this application.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
08-111-19
RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
0811119
RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
18-081-19
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. U0402-00 - Invalid Data Received From TCM. P1DD2-00 - Torque Request Signal From TCM Denied. U1424-00 - Implausible Engine Torque Signal Received. Customers may experience excessive oil consumption between oil change intervals.In addition, the following software enhancement is available:Multiair solenoid electrical opening change to resolve idle tick/tap issue.
V54 REV1
Revised Customer Satisfaction Notification V54 Engine Cooling Fan
08-089-19
Flash Over The Air (FOTA) Software Update RA3 and RA4 Radio This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
18-040-19
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Some customers may experience the following condition:When pressing the SPORT button on the console, the SPORT mode is not activated. Hard to start condition at low temperatures 10-15°C (50-60°F) and filled with 70~80% ethanol fuel (DF7 Transmission Sales Code only). Engine experiencing a hard re-start after being shut off for short periods of time. Engine Stop/Start (ESS) remains in stop condition and they must manually restart the engine due to either a door or the hood being opened while in ESS mode.
02-009-17
Creak/Rattle Noise Heard From Front Suspension This bulletin involves installing a protective sleeve in the front coil springs suspension. The customer may notice a creaking or rattle noise from the front of the vehicle while driving over bumps or rough roads.
08-110-17
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure.
21-048-17
Flash: Transmission Diagnostic and Shift Enhancements AN-BQ-21-20171106 Refer to China Joint Venture (JV) released document AN-BQ-21-20171106, for details on this service action.
9003293
A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.
08-108-17
Windshield Washer Pump Leaking This bulletin involves replacing the windshield washer pump due to a leak. Some customers may describe that their is washer fluid leaking from the reservoir in the front of the vehicle.
1809017
Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a ticking noise coming from the top of the engine area. The ticking noise is heard particularly at idle.
1801617
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U0402 - Implausible Data Received From TCM. P1DD2 - Torque Request Signal From TCM Denied. U1424 - Implausible Engine Torque Signal Received. P0101 - Mass Air Flow Sensor "A" Circuit Performance. U0418 - Invalid Data Received From Brake System Control Module. P0128 - Thermostat Rationality. P0703 - Brake Switch 2 Performance. P1185 - General Pressure Sensor Correlation. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. In addition, the following software enhancements are available:Changes which allow the catalytic convertor to operate cooler. Multiair solenoid electrical opening change to resolve idle tick/tap issue. Cruise control enhancements.
9003800
A/C Plumbing Line, TXV, A/C Condenser For BU models ONLY: A/C components leaking. Before replacing any of the A/C part numbers listed, call: Viraj Vartak at cell phone: (248) 512-3859. If no response in 15 minutes, please proceed with repair.
0810217
RA2 RJ2 RG2 RL2 and RM2 Radio Enhancements This bulletin involves updating the radio with the latest available software. The customer may notice one of the following:The parking sensor (warning chime) is still audible after the key is in the off position(EMEA and APAC Only). The radio re-boots if more than five favorite presets are set for each category (i.e. Sport or Rock)(RA2 Sales Code Only). Emergency number (i.e. 911) not set as default(U.S. BU Vehicles Only). Radio re-boots or displays black screens. When receiving or making outgoing phone calls, the other person may hear an echo or repeated phrases(16 MY FB Only). A false message displayed in the Instrument Panel Cluster (IPC) such as ?Parking Sensors Unavailable? and/or ?Sound System Unavailable?(16 MY FB Only).
2301317
Front My Sky Panel Unable To Be Manually Removed From Vehicle This bulletin involves applying weather strip lubricant to the front My Sky roof panel seal. Some customers may describe that the My Sky opens and vents without issue. When the My Sky front panel is unlatched it does not release - panel is stuck in placeFig. 1.Panel That May Be Stuck1 - Panel That May Be Stuck
21-043-17
Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following Diagnostic Trouble Codes (DTCs) have been set:U1412 - Implausible Vehicle Speed Signal Received. P0887 - TCM Power Control Circuit High. U0001 - Automatic Gearbox Shifter Module (AGSM) CAN Communication BUS (BUS Off). P0901 - Clutch 1 Actuator Control Circuit Performance. In addition, the following software enhancement is available:Changes which allow the catalytic convertor to operate cooler.
18-016-17 REV. B
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:U0402 - Implausible Data Received From TCM. P1DD2 - Torque Request Signal From TCM Denied. U1424 - Implausible Engine Torque Signal Received. P0101 - Mass Air Flow Sensor "A" Circuit Performance. U0418 - Invalid Data Received From Brake System Control Module. P0128 - Thermostat Rationality. P0703 - Brake Switch 2 Performance. P1185 - General Pressure Sensor Correlation. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. In addition, the following software enhancements are available:Changes which allow the catalytic convertor to operate cooler. Multiair solenoid electrical opening change to resolve idle tick/tap issue. Cruise control enhancements.
18-086-17
Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following DTCs have been set:P1D7F - ETC Self-Learning Failure. P1524 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P0000-00 - Will be displayed in the scan tool, but should really be displaying P0326-00 (Knock Sensor 1 Circuit Performance). In addition, the customer may notice the following condition:Hard start condition caused by spark plugs fouling.
21-040-17
Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:P0887 - TCM Power Control Circuit High.
9003723
Amplifier Vehicles needing amplifier replacement, please call Rayyan Mohammed at Cell (248) 954-0790 prior to repair. If no response in 15 minutes, proceed with the repair.
1807217
P1CEA-00-Boost Side EVAP Purge System Performance, Possibly Caused by Incorrect Air Filter Box Installed This bulletin involves checking the correct air filter box is installed. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P1CEA-00 - Boost Side EVAP Purge System Performance
2103517
Flash: Transmission Diagnostic and Shift Enhancements AN-BQ-21-20170724.
1806517
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience the following condition:Engine Stop/Start (ESS) remains in stop condition and they must manually restart the engine due to either a door or the hood being opened while in ESS mode.
2102917
Flash: Transmission Diagnostic and Shift Enhancements AN-BQ-21-20170705.
9003741
BCM - Body Control Module 2017 Jeep Renegade (BU) Body Control Module (BCM). Engineering is investigating multiple control functions for Exterior Lights, Horn and Seats. Prior to replacing the BCM on 2017 MY Jeep Renegade vehicles, please contact Vaughn Meatte on cell (248) 388-0080. If no response in 15 minutes, please proceed with repair.
9003749
RA2 Radio 5" Uconnect Before replacing this radio, make sure you can reproduce the customer issue. If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.
9003357
Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.
9003739
Passive Keyfob 2017 Jeep Renegade Keyfobs (FOBIK) with Passive Entry Keyless Go Feature - Engineering is investigating a keyfob unable to program or no function or low keyfob coin battery condition. Prior to replacing keyfob on MY2017 Jeep Renegade vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.
9003413
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
21-023-17
Flash: Transmission Shift and Driveability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. The customer may describe that when the ignition is turned on, the odometer numbers flash.
9003696
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
18-029-17
Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.
23-013-17
Front My Sky Panel Unable To Be Manually Removed From Vehicle This bulletin involves applying weather strip lubricant to the front My Sky roof panel seal. .1 - Panel That May Be Stuck
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
03-001-17
Noise In Front Of Vehicle When Accelerating Or Decelerating This bulletin involves replacing both front half shafts. The customer may describe a ?clunk type? noise in front of the vehicle while accelerating or decelerating.
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
18-118-16
Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0000-00 - will be displayed in the scan tool, but should really be displaying P0326-00 (Knock Sensor 1 Circuit Performance).
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
06106092A
Seat Relay For a Jeep Renegade or Fiat 500X ONLY, if the driver's power seat will not move in any axis and the key is in the on position with the door open: 1. Please take a Vehicle Scan Report, taking note of any active or stored DTC's, especially in the Body Control Module (BCM). 2. Before replacing the relay, call Rick Gordon at cell (248) 630-6281. If no answer leave a message and if after 15 minutes, there is no return call, proceed with the repair. 3. In the event there is no call-back, please email the Vehicle Scan Report to rick.gordon@fcagroup.com
06106092A$
Seat Relay For a Jeep Renegade or Fiat 500X ONLY, if the driver's power seat will not move in any axis and the key is in the on position with the door open: 1. Please take a Vehicle Scan Report, taking note of any active or stored DTC's, especially in the Body Control Module (BCM). 2. Before replacing the relay, call Rick Gordon at cell (248) 630-6281. If no answer leave a message and if after 15 minutes, there is no return call, proceed with the repair. 3. In the event there is no call-back, please email the Vehicle Scan Report to rick.gordon@fcagroup.com
68232614A$
Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.
31-001-16
Do Not Apply Corrosion Protection On Sheet Molding Compound (SMC) Plastic Panels This bulletin involves discussing SMC plastic panels and applying corrosion protection.
D-15-13
Claim Reimbursement Guidelines - Radar Sensor Alignment Tool
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.