S2623000052 REV. A
Service Bulletin/Repair Instructions
Airbag Warning Light On or Intermittent. The Occupant Restraint Controller (ORC) May Have The Following DTCs (Active/Stored)
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2623000052 REV. A
Airbag Warning Light On or Intermittent. The Occupant Restraint Controller (ORC) May Have The Following DTCs (Active/Stored)
114265
TRANSMITTER KIT & TRANSMITTER - INTEGRATED KEY FOB
114268
TRANSMITTER KIT & TRANSMITTER - INTEGRATED KEY FOB
S2623000001 REV.A
Rotary Shifter Lights Blinking, Shifter Not Moving, Not Going Into Gear.
9100861 Rev 4
PUMP, Auxiliary Coolant, High Temperature Before replacing the High Temperature Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash.
114072
MOTOR - WINDOW REGULATOR
114073
MOTOR - WINDOW REGULATOR
S2508000029 REV.B
Instrument Panel Cluster (IPC) Message “Park Assist System Unavailable” or “Service Park Assist System”, “Rear Braking Assist Unavailable” or “Service Rear Braking Assist System" with Performance Diagnostic Trouble Codes (DTCs)
S2623000052
Airbag Warning Light On or Intermittent. The Occupant Restraint Controller (ORC) May Have The Following DTCs (Active/Stored)
S2508000029 REV.A
Instrument Panel Cluster (IPC) Message “Park Assist System Unavailable” or “Service Park Assist System”, “Rear Braking Assist Unavailable” or “Service Rear Braking Assist System" with Performance Diagnostic Trouble Codes (DTCs)
S2523000053 REV.C
Service Electric Power Steering (EPS) Message On Instrument Cluster. Rev B.
9100861 Rev 3
PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash. If correct repair is not performed then the claim or condition will be recovered by Warranty Operations.
18-070-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **U0104-00 - Lost Communication With Cruise Control Module (NA Market Only) (In Active or Stored status). ● U0405-00 - Invalid Data Received From Cruise Control Module (NA Market Only) (In Active or Stored status). NOTE: Vehicles setting DTCs U0405-00 and U0104-00 may experience an inability to be cleared.** ● P2AF6-00 - Dual Starter Relay Stuck (in active or stored status). ● P1CEA - Boost Side EVAP Purge System Performance (in active or stored status). ● P2C90-00 - Crankcase Ventilation System - Hose "A" Disconnected (in active or stored status). ● P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1 (in active or stored status). ● P0071-00 - Ambient Air Temperature Sensor Performance (in active or stored status). ● P0325-00 - Knock/Combustion Vibration Sensor 1 Circuit (in active or stored status). ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low (in active or stored status). ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High (in active or stored status). ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or (in active or stored status). ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1 (in active or stored status). ● U0673-00 - Lost Communication With Ion Sense Module (in active or stored status). ● P05BD-00 - Stop-Start Mode Switch Range/Performance (in active or stored status). ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/stuck Off (in active or stored status). ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance (in active or stored status). ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking (in active or stored status). ● P0330-00 - Knock/Combustion Vibration Sensor 2 Circuit (in active or stored status). This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
9100861 Rev 1
PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash.
S2523000053 REV.B
Service Electric Power Steering (EPS) Message On Instrument Cluster. Rev B.
9100861
PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Ensure the PCM is up-to-date with the latest available flash. 6) Inspect battery terminals for damage to rule out a battery drainage issue.
113276
CORE – HEATER
113277
CORE – HEATER
9100833 REV1
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S2508000025 REV. B
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
113123
SPRING KIT - DISC BRAKE PAD
08-248-26
Upcoming R1H Radio Over The Air Update U41.10 Software Version The customer may comment on one or more of the following: ● 'Forward Collision Warning (FCW) OFF' light ON, with no Diagnostic Trouble Codes (DTCs) and can't turn light off. ● Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera Functions Normally). ● Paddle shifters not working/no longer a setting. ● Autolocks not working. ● Auto headlights not working. ● AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). ● Album Art flickering issue. ● Blank screen and then reboot every 2 minutes and 40 seconds. ● CarPlay® icon disappears from main screen while still active, leaving no navigation path back. ● Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after a Firmware Over The Air (FOTA) updated. ● Valet mode sends duplicate requests causing Heads Up Display (HUD) and vehicle state misalignment. ● Rear seat media page intermittently shows a blank screen. ● Unable to select or drag 'Pitch and Roll' widget on home screen. ● USB playback resumes incorrectly, skipping to next track after reconnect. ● Album art not displayed on display screen despite availability in media. ● Incorrect call timer displayed for conference calls. ● Call status remains 'active' on widget after call ends. ● Second call status not updated on home screen widget. ● Rear entertainment tab intermittently blank when switching apps. ● System crashes for 20 to 30 seconds after voice reply action. ● Media progress bar continues incorrectly after second call acceptance. ● CarPlay® device fails to reconnect automatically or manually. ● Rear HVAC lock/unlock text missing while icon is present. ● Visual glitch observed on Front Passenger Display Module (FPDM) display. ● Surround View Camera (SVC) accessible while driving across apps (unexpected behavior). ● Instrument Panel Cluster (IPC) navigation map fails to load despite radio showing navigation. ● HUD layout resets after overnight sleep cycle. ● ParkSense triggers unintended surround camera activation. ● HUD settings not retained after ignition cycle. ● Audio focus stuck on Voice Recognition (VR); selected message not read. ● Preset bar appears blank after overnight sleep cycle. ● FM channel switches unexpectedly and reverts after delay. ● Massage activation causes HUD black screen/media disruption. ● Non-applicable ambient lighting setting visible in vehicle menu. ● Navigation screen appears black after system startup. ● Track name flickers on status bar during CarPlay® playback. ● HUD toggles between Home and Media screens without user input. ● Phantom touch causes navigation to switch from full screen to split view. ● HUD redirects to CarPlay® tab when exiting camera unexpectedly. ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera Functions Normally). ● Android Auto® VR inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (Rearview Camera Functions Normally). ● Ambient light inoperative. ● Map in IPC inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (Rearview Camera Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (Rearview Camera Functions Normally). ● Ghost touch on Navigation screen (Rearview Camera Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after view camera event selected by customer in the Camera View Pages (Rearview Camera Functions Normally).
S2508000025 REV.A
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
112979
CAMERA - REAR VIEW
112980
CAMERA - REAR VIEW
9100833
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S268A000014
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
S1623000028 Rev. K
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
9100832
Before replacing the starter, please follow the published diagnostics in the Service Information at 08 - Electrical / 8F - Engine Systems / Starting / Diagnosis and Testing / STANDARD STARTING SYSTEM. Updates to this procedure have been recently made and should be followed.
9100838
Before replacing any parts check for applicable TSBs/RSUs. If no applicable TSBs/RSUs, or they have already been applied, please refer to the updated Service Library diagnostic procedure for P1CEA-00-BOOST SIDE EVAP PURGE SYSTEM PERFORMANCE (MODULE, Powertrain Control (PCM), 3.0L GMET6) and SOL S2518000008.
9100834
Ambient cabin light fault B2811-02 inop. If Ambient Lights can change color and intensity, do not replace Auxiliary/Ambient Lighting Module (ALM). Follow the diagnostic for B2811-02. Before replacing, verify the vehicle PROXI is correct for the vehicle (2-row/3-row). If PROXI is incorrect, re-PROXI and then perform a hard reset of the ALM.
S1623000028 REV.J
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2608000026
Power Liftgate Will Not Power to a Fully Open Position, Adjustable Power Liftgate Height
08-221-26 REV. A
R1H Radio U41.10 USB Software Update Customers may experience one or more of the following: ● FCW OFF light ON with no DTCs and can't turn off. ● Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera Functions Normally). ● Paddle shifters not working/no longer a setting. ● Autolocks not working. ● Auto headlights not working. ● AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). ● Album Art flickering issue. ● Blank screen and then reboot every 2 minutes and 40 seconds. ● CarPlay icon disappears from main screen while still active, leaving no navigation path back. ● Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after FOTA. ● Valet mode sends duplicate requests causing HU and vehicle state misalignment. ● Rear seat media page intermittently shows a blank screen. ● Unable to select or drag 'Pitch and Roll' widget on home screen. ● USB playback resumes incorrectly, skipping to next track after reconnect. ● Album art not displayed on HMI despite availability in media. ● Incorrect call timer displayed for conference calls. ● Call status remains 'active' on widget after call ends. ● Second call status not updated on home screen widget. ● Rear entertainment tab intermittently blank when switching apps. ● System crashes for 20 to 30 seconds after voice reply action. ● Media progress bar continues incorrectly after second call acceptance. ● CarPlay device fails to reconnect automatically or manually. ● Rear HVAC lock/unlock text missing while icon is present. ● Visual glitch observed on Front Passenger Display Module (FPDM) display. ● Surround view camera accessible while driving across apps (unexpected behavior). ● IPC navigation map fails to load despite radio showing navigation. ● Head Up Display (HUD) layout resets after overnight sleep cycle. ● ParkSense triggers unintended surround camera activation. ● HUD settings not retained after ignition cycle. ● Audio focus stuck on VR; selected message not read. ● Preset bar appears blank after overnight sleep cycle. ● FM channel switches unexpectedly and reverts after delay. ● Massage activation causes HU black screen/media disruption. ● Non-applicable ambient lighting setting visible in vehicle menu. ● Navigation screen appears black after system startup. ● Track name flickers on status bar during CarPlay playback. ● HU toggles between Home and Media screens without user input. ● Phantom touch causes navigation to switch from full screen to split view. ● HU redirects to CarPlay tab when exiting camera unexpectedly. ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (Rearview Camera Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (Rearview Camera Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (Rearview Camera Functions Normally). ● Ghost touch on Navigation screen (Rearview Camera Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after view camera event selected by customer in the Camera View Pages (Rearview Camera Functions Normally). This bulletin involves inspecting and if required, updating the radio software level to U41.10. Depending on the radio's current software level the radio may need a one or two USB update.
OTHERDOC_163
Radio Over The Air Update to U41.10 R1H Software Version (FOTA) Customers may experience one or more of the following:- Inaccurate status or information displayed during phone calls- Voice Recognition performance- Carplay connectivity issues- Black / blank screens for Navigation or Media apps not affecting rearview camera funtionality- Visual glitch on Front passenger Display- Unresponsive widgets- Light & Dark mode discrepancy between screen views- Unresponsive hard button to turn screen off- Incomplete or innacurate pop-up notifications- Radio stuck in Valet Mode- Phantom / Ghost touch on Media screens- Incorrect menu disp
111785
MODULE - CENTRAL ADAS DECISION and DRIVER MONITORING
S1623000028 REV.I
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000038
Central ADAS Decision Module (CADM), Long Range Camera Front(LRCF), Advanced Driver Assist System (ADAS), Lane Assist Inoperative, Service Active Lane Management Message, Inside Rearview Mirror Cover and LRCF Windshield Bracket.
08-221-26
R1H Radio U41.10 USB Software Update Customers may experience one or more of the following: ● **FCW OFF light ON with no DTCs and can't turn off. ● Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera (RVC) Functions Normally). ● Paddle shifters not working/No longer a setting. ● Autolocks not working. ● Auto headlights not working. ● AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). ● Album Art flickering issue. ● Blank screen and then reboot every 2 minutes and 40 seconds. ● CarPlay icon disappears from main screen while still active, leaving no navigation path back. ● Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after FOTA. ● Valet mode sends duplicate requests causing HU and vehicle state misalignment. ● Rear seat media page intermittently shows a blank screen. ● Unable to select or drag 'Pitch and Roll' widget on home screen. ● USB playback resumes incorrectly, skipping to next track after reconnect. ● Album art not displayed on HMI despite availability in media. ● Incorrect call timer displayed for conference calls. ● Call status remains 'active' on widget after call ends. ● Second call status not updated on home screen widget. ● Rear entertainment tab intermittently blank when switching apps. ● System crashes for 20 to 30 seconds after voice reply action. ● Media progress bar continues incorrectly after second call acceptance. ● CarPlay device fails to reconnect automatically or manually. ● Rear HVAC lock/unlock text missing while icon is present. ● Visual glitch observed on FPDM display. ● Surround view camera accessible while driving across apps (unexpected behavior). ● IPC navigation map fails to load despite HU showing navigation. ● HUD layout resets after overnight sleep cycle. ● ParkSense triggers unintended surround camera activation. ● HUD settings not retained after ignition cycle. ● Audio focus stuck on VR; selected message not read. ● Preset bar appears blank after overnight sleep cycle. ● FM channel switches unexpectedly and reverts after delay. ● Massage activation causes HU black screen/media disruption. ● Non-applicable ambient lighting setting visible in vehicle menu. ● Navigation screen appears black after system startup. ● Track name flickers on status bar during CarPlay playback. ● HU toggles between Home and Media screens without user input. ● Phantom touch causes navigation to switch from full screen to split view. ● HU redirects to CarPlay tab when exiting camera unexpectedly.** ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally) This bulletin involves inspecting and if required, updating the radio software level to **U41.10.** Depending on the radio's current software level the radio may need a one or two USB update.
08-217-26
Heads Up Display (HUD) Resets to Default Settings Each Ignition Cycle Customers may experience the following: ● The custom HUD configurations do not save after a vehicle sleep cycle. HUD configuration will reset to the default settings.
112180
BEZEL - OVERHEAD CONSOLE
9100532 REV1
Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, Electronic Stability Control (ESC) light on, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced. Note: WL / WS SCCMs do not contain a Steering Angle Sensor (SAS) The Steering Angle is computed within the Electronic Power Steering (EPS) module. See Electronic Power Steering (EPS) module for diagnosis and repair procedures.
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
111830
SENSOR – KNOCK
111831
SENSOR – KNOCK
111833
SENSOR – KNOCK
111834
SENSOR – KNOCK
S248A000015 REV.A
Poor Audio Quality And Or Static From Wireless Devices
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
111702
SWITCH - LIFTGATE
08-207-26
Instrument Panel Cluster (IPC) Flicker Turn By Turn The customer may experience flickering on their Instrument Panel Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay
111849
RADIO - MULTI MEDIA
9100808
Thermostat assembly PN 68361650AH already includes gasket PN 68361649AB, so do not order an additional gasket or list one separately in a claim. Please refer to the thermostat's MEDIA image.
111402
AIR BAG - DRIVER
111403
AIR BAG - DRIVER
S2308000034 REV.B
No Wireless Charging Or Slow Wireless Charging
S2523000003 REV.A
Door Latch, Handle And Ajar Additional Service Information.
08-075-26 REV. A
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S2623000024
U0422-00 Implausible Data From BCM Set In Central ADAS Decision Module (CADM).
111396
COOLER - AUXILIARY LOW TEMPERATURE
111128
THERMOSTAT – NONE
111129
THERMOSTAT – NONE
08-143-26
Traffic Sign Assist Unavailable – Service Required The customer may experience one or more of the following: SYMPTOM: ● “Traffic Sign Assist Unavailable – Service Required” message and icon displays on the Instrument Panel Cluster (IPC). This occurs after a remote start and typically at the first start of the day. ● The Odometer flashes when the traffic alert message is active. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
23-010-26
Intermittent Poor HVAC Performance Customers may comment on the following: SYMPTOM: ● Intermittently the HVAC blows or feels like the output has been reduced resulting in poor performance in cold temperatures. NOTE: This issue only happens in temperatures that fluctuate between freezing and slightly above. The thawing and refreezing process produces a build up of ice on the cowl baffles. This bulletin involves removing both right and left side rubber flaps from the cowl baffles.
S1623000028 REV.H
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2223000022 REV.E
Power Liftgate Inoperative Or Intermittently Will Not Open Or Close.
111121
SWITCH - POWER WINDOW
111124
SWITCH - POWER WINDOW
9100791
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.
S2408000016 REV.E
Front Passenger and/or Rear Left and/or Rear Right Door Window Switches are Inoperative, Window Operation Works from the Driver Master Switch
9100789
Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"
9100790
Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"
08-134-26
Universal Garage Door Opener (UGDO) Inoperable Technicians may or may not find the following Diagnostic Trouble Code (DTC) present: SYMPTOM: ● B251D1-00 - Universal Garage Door Opener Control. Customers may comment on the following: ● Operational questions regarding the usage of the HomeLink® UGDO. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
18-042-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P2AF6-00 - Dual Starter Relay Stuck (in active or stored status). ● P1CEA - Boost Side EVAP Purge System Performance (in active or stored status). ● P2C90-00 - Crankcase Ventilation System - Hose "A" Disconnected (in active or stored status). ● P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1 (in active or stored status). ● P0071-00 - Ambient Air Temperature Sensor Performance (in active or stored status). ● P0325-00 - Knock/Combustion Vibration Sensor 1 Circuit (in active or stored status). ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low (in active or stored status). ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High (in active or stored status). ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or (in active or stored status). ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1 (in active or stored status). ● U0673-00 - Lost Communication With Ion Sense Module (in active or stored status). ● P05BD-00 - Stop-Start Mode Switch Range/Performance (in active or stored status). ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/stuck Off (in active or stored status). ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance (in active or stored status). ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking (in active or stored status). ● P0330-00 - Knock/Combustion Vibration Sensor 2 Circuit (in active or stored status). ● P032A-00 - Knock - Combustion Vibration Sensor C Circuit (in active or stored status). ● P062B-00 - Internal Control Module Fuel Injector Control Performance (in active or stored status). ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/Performance (in active or stored status). ● P00F3-00 - Humidity Sensor Circuit Range - Pe
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2608000015
Memory Seat Does Not Work There Is No Response from The Seat While Pressing the Memory Seat Profiles from the Switch Diagnostic Trouble Code (DTC) B1D9B-54- Seat Horizontal Front Stop Not Learned-Missing Calibration
9100203 Rev 3
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract.
S2219000004 REV.A
Service Electric Power Steering Message On Cluster. C0051-54 Steering Wheel Position Sensor Calibration, C0051-64 Steering Angle Set.
S2608000005
Power Liftgate Module Sets Diagnostic Trouble Code B1963-00 Power Liftgate Performance
S2523000070 REV.A
Central ADAS Decision Module (CADM) Diagnostic Trouble Codes C00C0-4A, C00C1-4A, C00C5-4A.
110220
HANDLE - EXTERIOR DOOR
08-106-26
Flash: Global Telematics Box Module (TBM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B22A9-96 - ECU Internal Performance-Component Internal Failure. ● B1560-11 - Cellular Antenna 1-Circuit Short To Ground. ● B1560-13 - Cellular Antenna 1-Circuit Open. ● B1561-11 - Cellular Antenna 2-Circuit Short To Ground. ● B1561-13 - Cellular Antenna 2-Circuit Open. ● B1562-14 - GPS Antenna-Circuit Short To Ground Or Open.** The customer may experience the following: ● Uconnect Box requires service message at start up on the display screen. This bulletin involves reprogramming the TBM with the latest available software.
9100779
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only or if Z part is not in stock.
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
23-006-26
Power Running Board Trim Paint Peeling Customers may comment on the following: SYMPTOM: ● The running board black trim paint is peeling Fig. 1 and Fig. 2. This bulletin involves painting and replacing one or both power running boards as required.
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
23-005-26
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: SYMPTOM: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2408000016 REV.D
Front Passenger and/or Rear Left and/or Rear Right Door Window Switches are Inoperative, Window Operation Works from the Driver Master Switch
9100777
Before replacing any parts check for applicable TSBs/RSUs. If no applicable TSBs/RSUs, or they have already been applied, please refer to SOL S2518000008.
2323000066 REV.A
Buzz Squeak Rattle (BSR) From Left Rear Cargo Area Near Subwoofer.
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
110463
SWITCH - TRAILER BRAKE CONTROL MODULE , ADAPTER & WIRING KIT - TRAILER TOW.
08-075-26
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S228A000025 REV.A
Harman R1H Uconnect 5 Radio Software Flash Error Codes
S2423000027 REV.D
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
S2514000003 REV.B
MIL-On/Check Engine Lamp (CEL)-On
S258A000002 REV.C
Radio Screen Goes Blank, Radio Locks-Up and/or the Radio Wording Switches From English-to-Italian. Rearview Camera (RVC) Functions Normally
S2623000007
The Handsfree Kick Feature Does Not Work Or Works Intermittently.
9100591 Rev 1
Universal Garage Door Opener Prior to replacing the UGDO or sun visor, call HomeLink® Customer Care at 1-800-355-3515 for a proper evaluation of the issue. If this does not correct the issue, please follow the steps in SOL: S2508000039
9100768
If the Power Liftgate (PLG) does not operate following battery drainage or when DTCs B2199-16 or B21DD-16 are active, perform the following steps: 1. Verify Battery Voltage: Ensure battery voltage is at nominal value (minimum 12.5 V). Charge the battery, if necessary before proceeding. 2. Confirm Low Voltage DTCs: After charging, verify that any low battery voltage DTCs are stored. 3. Check PLGM Proxi Alignment: 4. If PLGM is not aligned: - Perform Proxi Alignment - Reset the module - Perform module recalibration. 5. If Proxi Is Correct: - Reset the module. - Perform module calibration. 6. Diagnose Active DTCs 7. Inspect wiring and related components associated with those DTCs. Repair as necessary and clear DTCs. 8. Module Replacement: If the module does not accept Proxi alignment, Module reset, or Calibration.
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S268A000005
Front HDMI Port or Front Passenger Display Module (FPDM) Not Projecting Video
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
110207
GLASS - QUARTER WINDOW
S2308000120 REV.F
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
9100757 Rev 1
If replacing the oil pump on 22-24MY WS 3.0L HO, please follow the diagnostic procedure "09 - Engine, 3.0L GMET6 / Lubrication / PUMP, Engine Oil / Removal and Installation / ENGINE OIL PUMP" to replace the pump without removing the transmission and using the original solenoid.
9100758 Rev 1
If replacing the oil pump on 23-24MY WS 3.0L SO, please follow the diagnostic procedure "09 - Engine, 3.0L GMET6 / Lubrication / PUMP, Engine Oil / Removal and Installation / ENGINE OIL PUMP" to replace the pump without removing the transmission and using the original solenoid.
S2607000002
Hemi Water Pump Coolant Leak Inspection
9100565Rev3
C0582-00-BRAKE BOOSTER MOTOR "A" PHASE U-V-W CIRCUIT RANGE/PERFORMANCE C058A-00-BRAKE BOOSTER MOTOR "A" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE C058E-00-BRAKE BOOSTER MOTOR "B" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE After performing the diagnostic tests and determines to replace the Brake System Control Module (BSCM) also replace the EBooster. (Send back both Brake Electronic Control Unit and Hydraulic Control Unit for Engineering Analysis) To avoid potential charge-back, only use MOPAR approved brake fluid per the service manual. When filling the brake reservoir, use clean equipment and gloves during repair to avoid cross-contamination.
S2523000089 REV.A
Passive Entry Exterior Door Handle Inoperative When Touched For Lock And Or Unlock.
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
08-012-26
Speaker Diagnostic Procedure Rattle, buzz and squeak coming from specific speakers.
S2308000120 REV.E
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
109152
CORE – HEATER
109153
CORE – HEATER
47B Combo REV2
Labor time reduced for oil pump replacement and 4x4 equipped opt. eqp.
S2623000001
Rotary Shifter Lights Blinking, Shifter Not Moving, Not Going Into Gear.
S2623000002
Service Shifter Message On Instrument Cluster With Loss Of Communication Diagnostic Trouble Code (DTC) Related To The Shifter.
109398
RACK KIT - REMOVABLE
109399
RACK KIT - REMOVABLE
109231
LATCH - LIFTGATE
109232
LATCH - LIFTGATE
08-368-25 REV. A
Drivetrain Control Module (DTCM) Software Update Customers may experience one or more of the following: ● Rear axle bind during slow speed turning. Feels like the 4WD is active. ● While moving above 5 kph (3.1 mph) transmission goes into limp mode This bulletin involves **reprogramming** the DTCM to the latest software level.
109174
STABILIZER BAR ASSY - FRT SUSPENSION and STABILIZER BAR – FRONT and LINK - STABILIZER BAR
9100227Rev3
Part Number is more precise than "Up to and Including" and "After" dates in the item description. Please ensure to order the correct CADM and Long Range Camera Part Number(s) the vehicle was built with. The Root of the Original and Replacement part should be identical, the difference will be in the NIK level. Technician Removal of the Long Range Camera and CADM for Testing Purposes: Please ensure the root of the Original and Replacement part are identical.
08-394-25 REV. A
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure.
S2508000107
Comfort Seat Module (CSM) or Comfort Steering Wheel Module (CSWM) do Not Operate
9100734
If the DTC B1E21-96: Backup Battery-Component Internal Failure is active and customer states Popup message will show at the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347
08-394-25
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present echnicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure
108941
MODULE - STEERING CONTROL
108942
MODULE - STEERING CONTROL
108953
DUCT - CLEAN AIR
S2318000005 REV.C
The customer’s complaint may include a message appearing in the cluster’s information center stating, “See User’s Manual For Proper Oil And Fuel” or “Service Engine See Dealer”. The customer may also mention a “low power” complaint.
S258A000021
Diagnostic Trouble Code (DTC) B15A1-00 Media Port Connection 1 Connection Found Set.
S2502000001
Lower Ball Joint / Lower Control Arm Servicing Updates.
08-142-25 REV. A
Flash: Power Liftgate Module (PLGM) Updates Customers may experience **one or more of** the following symptoms: ● **The power liftgate will not open. ● The power liftgate system chimes when trying to operate the liftgate using a Hands Free Entry (HFE) kick while no key is detected in the zone. ● After enabling or disabling the HFE kick or the Power Liftgate Alert feature, the PLGM does not save the changes. ● Vehicle will not start due to a depleted battery.** ● The power liftgate latch releases after pressing the exterior handle switch, but the liftgate does not power open. This bulletin involves **inspecting and possibly** updating the PLGM with the latest software.
08-174-25 REV. A
Flash: Body Control Module (BCM) Updates Customers may experience one or more of the following: ● Battery drained. ● Ignition off draw. ● Instrument Panel Cluster (IPC) goes off and on when the vehicle goes into sleep mode. ● Door lock indicator lamps stay illuminated. This bulletin involves **inspecting and possibly** updating the BCM with the latest available software.
08-344-25 REV. A
Security Gateway Module (SGW) Software Update he following software enhancements are available: ● Update for Diagnostic Trouble Code (DTC) U3033-00 - Control Module Security Certificate Missing/Invalid. NOTE: This DTC will not turn on the Malfunction Indicator Light (MIL) but is active or stored and cannot clear. ● If a FOTA message appears specifically directing the customer to service OR repeated FOTA events are not being completed, then a manual flash is required for the SGW update. ● SGW is not responding to diagnostics and showing offline This bulletin involves **inspecting and possibly** flashing the SGW to the latest software level in the case that the FOTA did not function.
S2523000089
Passive Entry Exterior Door Handle Inoperative When Touched For Lock And Or Unlock.
08-091-25 REV. B
Flash: Radio Frequency Hub Module (RFHM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B1A10-00 - RKE FOB 1 Battery Low. ● B1A11-00 - RKE FOB 2 Battery Low. ● B23D7-14 - Gated Park Control - Circuit Short To Ground Or Open. Customers have experienced: ● **Intermittent key fob detection. ● Possible dead batteries in key fobs. ● Proximity Wake-Up (welcome feature) does not activate at times.** ● Uconnect app requests not functioning (none of the app functions work, lock/unlock, remote start). ● Vehicle won’t start unless the key fob is pressed to Keyless Ignition Node (KIN). ● Key fob not detected when inside vehicle. ● Passive Entry (PE) intermittently inoperative. ● KIN unresponsive This bulletin involves inspecting and possibly updating the RFHM module with the latest available software.
S2308000034 REV.A
No Wireless Charging Or Slow Wireless Charging
108458
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
108461
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
S2508000100
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
08-368-25
Drivetrain Control Module (DTCM) Software Update Customers may experience one or more of the following: ● Rear axle bind during slow speed turning. Feels like the 4WD is active. ● While movingThis bulletin involves flashing the DTCM to the latest software level. above 5 kph (3.1 mph) transmission goes into limp mode.
9100721
As of October 30, 2025 the 77C recall inspection instructions were revised. Prior to ordering parts, please ensure the vehicle has been inspected to the latest recall procedure to determine whether 77C part replacement is necessary. It is possible a vehicle that failed inspection and needed a part according to the previous instructions may no longer need a part based on the newly revised inspection instructions.
S2403000005 REV.A
Malfunction Indicator Lamp (MIL) Illumination And Service Transmission Message Displayed. Diagnostic Trouble Code (DTC) P0607-ECU Internal Performance
S2508000095
Cluster Displays “Blindspot Alert Unavailable Service Required” Warning Message, Driver/Passenger Mirror Blind Spot Detection Lights Stay ON, ADAS Features Disabled. Multiple DTC’s Active Or Stored
9100708
DTC B1E21 is triggered when the TBM Backup Battery is discharged, inactive, or drained. This can happen during the lifetime of the vehicle. TBM should not be replace for B1E21, since there is no fault on TBM. TBM battery is replaceable. Part number of the back-up battery inside TBM is 68597650AA.
9100437Rev1
The service shifter message comes on in the cluster and the lever gets stuck in park "P" and it can be present the follwoing DTC: - U11E3 - TCM Lost communication with ESM on D-PT CAN - U0103 - Lost communication with Electric Gear Shift Module - U0101- Lost communication with DTCM - U0418 - Implausible Data Received From Brake System Control Module - U0402 - Implausible data received from TCM **NOTE: Prior any shifter replacement Refer to TSB-21-016-25 2024-2025 WS - Valve Body Replacement. Recommended Diagnosis procedure: 1. Confirm if U0101 -Lost Communication with TCM or U0418 -Implausible Data Received From Brake System Control Module are present, if so check the Valve Body CAN Terminals any corrosion. 2. Check the wiring connectors between the ESM and the TCM and check voltage. 3. Check the pin header for the ESM for any bent pins. 4. If wiring and voltage are good and the DTCs (U11E3 - TCM Lost communication with ESM on D-PT CAN & U0103 - Lost communication with Electric Gear Shift Module) are still present, erase them with the scan tool. Reset ECU. 5. if DTCs for loss communication are still active at the ESM and you are still unable to shift then replace the Shifter module.
9100694
Dealerships are replacing entire brake pedal assemblies to resolve accelerator pedal concerns. SBOM provides the accelerator as a separately serviceable assembly. Tech Tip Message Requested: "For your awareness, if replacement of the accelerator pedal is necessary, it can be ordered individually rather than as part of the complete pedal assembly. This helps prevent unnecessary repairs and potential chargebacks."
S2508000091
Radio (ETM) Is Always Setting Stored DTC B15A1-00 Media Port 1 Connection
08-344-25
Security Gateway Module (SGW) Software Update he following software enhancements are available: ● Update for Diagnostic Trouble Code (DTC) U3033-00 - Control Module Security Certificate Missing/Invalid. NOTE: This DTC will not turn on the Malfunction Indicator Light (MIL) but is active or stored and cannot clear. ● If a FOTA message appears specifically directing the customer to service OR repeated FOTA events are not being completed, then a manual flash is required for the SGW update. ● SGW is not responding to diagnostics and showing offline. This bulletin involves flashing the SGW to the latest software level in the case that the FOTA did not function.
9100672 Rev 3
Replacement components for transfer case are no longer available. To repair issue, use the following part numbers and follow the I-sheet instructions for assembly: 68738079AA - HOUSING 68738084AA - CAM 68738085AA - GEAR 68737112AA - PLATE Please note that the part numbers listed here are transfer case components, not full transfer case part numbers.
105646
MODULE - STEERING CONTROL & COLUMN
09-006-25 REV. A
Engine Overheating Customers may experience the following: ● Engine overheating with "Engine Overheated" message in the Instrument Panel Cluster (IPC). NOTE: The vehicle will be operable but at a reduced level of performance This bulletin involves replacing the engine thermostat.
S2524000012
High Voltage Air Conditioning Refrigerant Dye
S2522000003
Tire Pressure Monitor (TPM) Warning Lamp On Or Flashing. Sensor(s) Not Reading And Or Showing Dashes.
08-310-25
R1H Radio U33.43 USB Software Update Customers may experience one or more of the following: ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally) This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio's current software level the radio may need a one or two USB update
S2523000083
Passive Entry Outside Door Handle Does Not Unlock Or Lock The Vehicle Doors.
9100325 Rev 1
Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.
107450
TRANSMITTER - INTEGRATED KEY FOB
S2518000008
Malfunction Indicator Lamp (MIL) Is On
S258A000002 REV.B
Radio Screen Goes Blank, Rearview Camera (RVC) Functions Normally
9100672 Rev 1
Replacement T-Case is no longer available. To repair issue, use the following parts numbers and follow the I-sheet instructions for assembly: 68738079AA - HOUSING 68738084AA - CAM 68738085AA - GEAR 68737112AA - PLATE
S2505000008
C0044-00-BRAKE PRESSURE SENSOR 1 (MODULE, Brake System Control 2 (BSCM 2))
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
9100671
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
9100549 Rev 3
WL/WS/LB Key fobs unable to be programmed at dealers. Please check current stock and verify a Blue "OK" mark on part label. Return all parts that do not have the blue "OK" marking to Mopar under RMA 8925-792 and replace with clean stock from Mopar. FOBs with no marking or a Green Check mark should also be returned.
OTHERDOC_149
Global Telematics Box Module Over The Air Update from R5C1 and R5O1 to R5T TBM2.H Software Version (FOTA) Customers may experience one or more of the following: - Error display of "Uconnect Box Requires Service" popups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ]. - TBM sleep mode not working causing battery drain in some cases. - Error display of "Uconnect Box Requires Service/Wifi Unavailable" pop ups; [ TBM DTC B22A9-96 Internal Performance Failure ].
08-287-25
Flash: Global Telematics Box Module (TBM) Updates The customer may experience the following: ● Uconnect Box requires service message at start up This bulletin involves reprogramming the TBM with the latest available software.
S2408000118 REV.C
Vehicle Key FOB Functions for Passive Entry, Lock and Unlock, and Passive Keyless Go Starting Intermittently Do Not Operate
S2508000066
Center Stack Unresponsive (HVAC Buttons, Temperature Buttons)
S2505000006
Ebooster Electronic Booster Service Information.
S2522000001
TPMS Handling & Installation Best Practices
S2522000002
Customer Indicates Tire Pressure Monitoring System (TPMS) Lights On Dash.
21-016-25 REV. C
Valve Body Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U0101 - Lost Communication With The Transmission Control Module (TCM). ● U0402 - Implausible Data Received From TCM. ● U0418 - Implausible Data Received From Brake System Control Module 1. Customers may also comment on the following: ● Vehicle will go in limp-in mode. After the vehicle enters limp-in mode and has been shifted into Park, the vehicle will not shift into a forward or reverse gear This bulletin involves replacing the transmission valve body assembly.
23-010-25 REV. A
Power Running Board Trim Paint Peeling Customers may comment on the following: ● The running board black trim paint is peeling Fig. 1 and Fig. This bulletin involves **painting and** replacing one or both power running boards as required.
9100646
False fails on PCR, DBSM and PDCs Stuck Closed or open diagnostics, DTC P2AF5 or P2AF6, leading to NTF and unnecessary replacements. Current controls are not robust against depleted auxiliary battery condition. Please follow SOL S2508000031.
9100650
False fails on PCR, DBSM and PDCs Stuck Closed or open diagnostics, DTC P2AF5 or P2AF6, leading to NTF and unnecessary replacements. Current controls are not robust against depleted auxiliary battery condition. Please follow SOL S2508000031.
S2408000079 REV.A
Liftgate Lock Button Inoperative, Cluster Message “Service Keyless System”
S258A000019
Radio Does Not Turn On Automatically When Vehicle Is Started
21-016-25 REV. B
Valve Body Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U0101 - Lost Communication With The Transmission Control Module (TCM). ● U0402 - Implausible Data Received From TCM. ● U0418 - Implausible Data Received From Brake System Control Module 1. Customers may also comment on the following: ● Vehicle will go in limp-in mode. After the vehicle enters limp-in mode and has been shifted into Park, the vehicle will not shift into a forward or reverse gear. This bulletin involves replacing the transmission valve body assembly.
S2508000055
Rear Liftgate Handsfree Feature Does Not Operate, Only Operates When the Key is in The Off Position
S2408000016 REV.C
Front Passenger and/or Rear Left and/or Rear Right Door Window Switches are Inoperative, Window Operation Works from the Driver Master Switch
9100641
Symptoms/Condition: Shifter reports loss communication AND NO OTHER MODULES report the condition. Diagnostic: Please make sure ONLY shifter reports loss communication. If there are other modules reporting loss communication, then follow the existing service procedure Repair Procedure: 1. Verify Complaint - ESM reports a Loss of Communication (LOC) DTC, but no other modules do. - If multiple modules report the same LOC, the ESM is not the cause (its not a gateway module). 2. Read DTCs - Relevant codes: U0101, U0140, U0155, U0129, U11C3, U0402, U0422, U0423, U0415, U145D. - If multiple LOC DTCs are present: a. Check battery health, system voltage, and TCM (including valve body). b. If TCM goes offline, ESM may falsely report LOC DTCs. 3. Check Environmental Data - Look for voltage/system issues at the same mileage. a. If DTCs clear, do not replace ESM. b. If not, inspect: b.1 Module connectors/pins: If damaged, dont repair shifter. b.2 TCM connectors/pins: Same rule. b.3 AGSM connectors/pins: If damaged, repair shifter. b.4 AGSM wiring harness: If damaged, dont repair shifter. 4. Review Past Service - Confirm battery and TCM-related repairs are still effective. a. If not, fix and clear DTCs. b. If yes, continue. 5. Check for Other LOCs - If other modules report LOC to the same module, inspect that module. - If not, repair the AGSM. Additional Description: - The ESM only communicates with the TCM and is fully controlled by it. - In non-combustion engines, the TCM is replaced by the PCM. - If a stored DTC in the ESM disappears and doest return, do not replace the ESM.
S2108000236 REV.B
Windshield HUD (Head Up Display) Display Features
S258A000017
Door speaker Inoperative or No Sound
S2408000118 REV.B
Vehicle Key FOB Functions for Passive Entry, Lock and Unlock, and Passive Keyless Go Starting Intermittently Do Not Operate
106344
MANIFOLD - INTAKE
9100629
Before replacing the Headlamp Switch, due to an issue on the Dimmers. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. If it is the Instrument panel Dimmer (Right Dimmer) 2.- Review the resistance value between Pins 6 & 3. The value should be around 5.76 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). If it is the ambient light dimmer (Left Dimmer) 2.- Review the resistance value between Pins 8 & 3. The value should be around 14.55 KOhms, when in the lowest position (Dome defeat) to 182 ohms in the top position If a problem is found in the resistor values. Please replace the Switch.
S258A000002 REV.A
Radio Screen Goes Blank, Rearview Camera (RVC) Functions Normally
23-006-25 REV. B
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield.
S2523000072
Central ADAS Decision Module (CADM), Long Range Camera Front (LRCF), Advanced Driver Assist System (ADAS). AEB ACC FCW Message On Cluster.
S2422000001 REV.D
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
S2523000053 REV.A
Service Electric Power Steering (EPS) Message On Instrument Cluster.
S2523000071
1 st Or 2 nd Row Center Console Armrest Door Difficult To Slide Open And Or Closed.
S2523000070
Central ADAS Decision Module (CADM) Diagnostic Trouble Codes C00C0-4A, C00C1-4A, C00C5-4A.
105648
MODULE - ENGINE CONTROLLER
S2519000006
Steering Repair Information Involving Toe Angle. Tie Rod And Or Electric Power Steering (EPS) Units.
S2408000126 REV.A
Diagnostic Trouble Code (DTC) B1A0A-00 Remote Keyless Entry (RKE) FOB 3 Performance
S2519000005
Service Electric Power Steering Message On Cluster.
S2508000057
Night Vision Field Of View Limited And No Option To Overlay Analog Gauges
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2219000005 REV.D
Check Engine Lamp On. Warning Messages in the Cluster. U0131 Lost Communication with Power Steering Control Module Set.
9100565 Rev 1
C0582-00-BRAKE BOOSTER MOTOR "A" PHASE U-V-W CIRCUIT RANGE/PERFORMANCE C058A-00-BRAKE BOOSTER MOTOR "A" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE C058E-00-BRAKE BOOSTER MOTOR "B" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE After performing the diagnostic tests and determines to replace the Brake System Control Module (BSCM) also replace the EBooster. (Send back both Brake Electronic Control Unit and Hydraulic Control Unit for Engineering Analysis) To avoid potential charge-back, only use MOPAR approved brake fluid per the service manual. When filling the brake reservoir, use clean equipment and gloves during repair to avoid cross-contamination.
9100615
Power brake booster To avoid potential charge-back, only use MOPAR approved brake fluid per the service manual. When filling the brake reservoir, use clean equipment and gloves during repair to avoid cross-contamination.
9100614
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
9100549REV1
Keyfob WL/WS/LB Key fobs unable to be programmed at dealers. Please check current stock and verify a Blue "OK" mark on part label. If not present send part back to Mopar under RMA 8925-792 and replace with clean stock from Mopar. Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern.
08-185-25
Loss Of Power Steering Assist Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs) as active: ● C1593-00 - Steering Torque Sensor Circuit. ● C0051-64 - Steering Angle Sensor (EPS) - Signal Plausibility Failure. Customers may experience one or more of the following: ● "EPS" indicator is illuminated on the Instrument Panel Cluster (IPC). ● Partial or full loss of power steering assist. ● Once the DTC is set, the reduction or loss of assist will remain for the remainder of the key cycle This bulletin involves involved inspecting the Electronic Power Steering (EPS) wire harness connector, cleaning the connector or possibly replacing the electric rack and pinion gea
S2514000003 REV.A
MIL-On/Check Engine Lamp (CEL)-On
S2509000006
Mil-On/Check Engine Lamp (CEL)-On
S2514000003
MIL-On/Check Engine Lamp (CEL)-On
S2523000053
Service Electric Power Steering (EPS) Message On Instrument Cluster.
S2523000054
Intermittent Vibration Buzz Squeak Rattle (BSR) Shaking Felt In Steering Wheel.
105289
TRANSMITTER - INTEGRATED KEY FOB
9100596
Gear Assy - Steering Rack 1) If below DTCs are observed, please refer to 08-095-25 REV. B (For MY24) and 08-094-25 REV. A (For MY25) U0420-00 - Invalid Data Received from Power Steering Control Module. (Set by CADM2) C2217-00 - Electric Power Steering Module Internal. C221F-00 - ECU Not Initialized. C1592-00 - Electronic Power Steering Motor Circuit. C1593-00 - Steering Torque Sensor Circuit. 2) IF C2217 DTC is observed to be active, please make sure that both connectors on EPS are receiving voltage ranging between 10V-16V
104970
CORE - HEATER
9100599
Underhood start/stop safety The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.
S2509000003REVA
Engine Overheating Customer Complaint/Technician Observation: Customer complaint may include engine “overheating”. Discussion: When dealing with a customer complaint of engine ”overheating”, it is most important to understand exactly what the customer’s definition is of “overheating”. An explanation from the customer of what exactly happened is necessary. Overheating descriptions could include warning lamp(s), messages in the cluster, steam/smoke coming from under the hood, gauge “running higher than normal”, actual engine temperature higher than what the customer considers normal, smells hot, coolant leaking under the vehicle, etc. Observed engine operating temperatures of 245 F (118 C) degrees or lower are typical and are NOT considered overheating.
9100576
Transfer Case Motor Gear: Confirm the attachment points from the wiring routes when they inspect a shift motor on the t-case. Review the connection of the connector X238A, make sure it's fully seated and that the lever is fully locked on the connector.
08-174-25
Flash: Body Control Module (BCM) Updates Customers may experience one or more of the following: ● Battery drained. ● Ignition off draw. ● Instrument Panel Cluster (IPC) goes off and on when the vehicle goes into sleep mode. ● Door lock indicator lamps stay illuminated. This bulletin involves updating the BCM with the latest available software.
02-002-25
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
08-091-25 REV. A
Flash: Radio Frequency Hub Module (RFHM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B1A10-00 - RKE FOB 1 Battery Low. ● B1A11-00 - RKE FOB 2 Battery Low. ● B23D7-14 - Gated Park Control - Circuit Short To Ground Or Open. Customers may also experience one or more of the following: ● Uconnect app requests not functioning (none of the app functions work, lock/unlock, remote start). ● Vehicle does not start. ● Passive Entry (PE) intermittently inoperative. ● Keyless Ignition Node (KIN) unresponsive. ● Welcome feature does not activate at time This bulletin involves inspecting and possibly updating the RFHM module with the latest available software.
08-095-25 REV. B
Flash: Electric Power Steering (EPS) Module Updates The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ● **U0420-00 - Invalid Data Received From Power Steering Control Module.** ● C2217-00 - Electric Power Steering Module Internal. ● C221F-00 - ECU Not Initialized. ● C1592-00 - Electronic Power Steering Motor Circuit. ● C1593-00 - Steering Torque Sensor Circuit. Customers may also experience the following: ● Loss of steering assist and/or a steering warning light on in the Instrument Panel Cluster (IPC). NOTE: **If the power steering assist is lost, it will remain out until the next key cycle.** This bulletin involves updating the EPS module with the latest available software.
21-016-25 REV. A
Valve Body Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U0101 - Lost Communication With The Transmission Control Module (TCM). ● U0402 - Implausible Data Received From TCM. ● U0418 - Implausible Data Received From Brake System Control Module 1. Customers may also comment on the following: ● Vehicle will go in limp-in mode. After the vehicle enters limp-in mode and has been shifted into Park, the vehicle will not shift into a forward or reverse gear This bulletin involves replacing the transmission valve body assembly.
S2508000039
Universal Garage Door Opener (UGDO) Inoperative, LED Indicator Lamps Not Illuminating
08-158-25
Flash: Air Suspension Control Module (ASCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● U0300-00 - Internal Control Module Software Incompatibility. Customers may also experience:** ● After towing a heavy load above the protection limit, the air suspension will only lower and will remain in low ride height. Instrument Panel Message (IPC) message "selected ride height not permitted due to payload" appears. This bulletin involves reprogramming the ASCM with the latest available software.
S2308000120 REV.D
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
104686
BOLT - HEX FLANGE HEAD
S2509000003
Engine Overheating
S2523000048
Blind Spot Warning Message Displayed on the Cluster
S2508000034
No Crank, No Start, Start Stop Inoperative. P2AF5-00 - Starter Relay 3 Stuck On, P2AF6-00 - Starter Relay 3 Stuck Off
S2523000045
C058E-00 - BRAKE BOOSTER MOTOR "B" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE
9100569
Video Routing Module Verify Z part number availability. Order a Z part number for all Exchange Orders: Warranty, Mopar, customer pay and service contract. Order regular part number for New, Unsold units only. Please review the latest version of SOL S2208000030 regarding DVD/blue ray issues. After updating software perform resets on both display or concern may still appear. After Battery Drainage VRM do not work. Please follow the following steps. 1. Check VRM proxi, if the VRM is not aligned, perform proxi alignment, reset module. 2. If proxi is correct, reset module 3. Check for DTCs, and check wiring and components related to those DTCs and clear them.
S2508000033
The Instrument Panel Cluster (IPC) Displays “Wipe Sensor” Message
08-142-25
Flash: Power Liftgate Module (PLGM) Updates Customers may experience one or more of the following symptoms: ● **Power Liftgate does not open or close the gate.** ● Liftgate latch releases after pressing exterior handle switch, but gate does not power open. This bulletin involves updating the PLGM with the latest software.
S2518000004
Mil-On/Check Engine Lamp-On
08-095-25 REV. A
Flash: Electric Power Steering (EPS) Module Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C2217-00 - Electric Power Steering Module Internal. ● C221F-00 - ECU Not Initialized. ● C1592-00 - Electronic Power Steering Motor Circuit. ● C1593-00 - Steering Torque Sensor Circuit. Customers may also experience the following: ● Loss of steering assist and/or a steering warning light on in the Instrument Panel Cluster (IP This bulletin involves inspecting and possibly updating the EPS module with the latest available software.
S2323000067 REV.A
Buzz Squeak Rattle (BSR) In The Door When Playing Music.
S2523000036
Sunroof Inoperative, Not Moving To Open Or Closed Positions.
S2523000038
Drivers Side Exterior Mirror Takes Longer To Defrost Or Clear Than The Passenger Side Exterior Mirror.
S2308000025 REV.A
No Crank, No Start, Start Stop Inoperative
S2308000120 REV.C
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
S2523000034
C008E-00 Setting After Windshield Replacement
9100565
Ebooster C0582-00-BRAKE BOOSTER MOTOR "A" PHASE U-V-W CIRCUIT RANGE/PERFORMANCE C058A-00-BRAKE BOOSTER MOTOR "A" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE C058E-00-BRAKE BOOSTER MOTOR "B" POSITION SENSOR CIRCUIT RANGE/PERFORMANCE After performing the diagnostic tests and determines to replace the Brake System Control Module (BSCM) also replace the EBooster. (Send back both Brake Electronic Control Unit and Hydraulic Control Unit for Engineering Analysis)
23-021-25
Liftgate Will Not Properly Open Or Close Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B197B-29 - Ratchet fork switch- signal invalid. ● B197C-29 - Pawl detent swich signal invalid. Customers may also experience the following: ● Liftgate will not properly open or close. ● Possible 'Liftgate Open' warning light on. ● Possible 'Liftgate Open' chime sound This bulletin involves installing a spacer below the liftgate striker.
S2508000029
Instrument Panel Cluster (IPC) Message “Park Assist System Unavailable” or “Service Park Assist System”, “Rear Braking Assist Unavailable” or “Service Rear Braking Assist System" with Performance Diagnostic Trouble Codes (DTCs)
9100549
Keyfob WL/WS/LB Key fobs unable to be programmed at dealers. Please check current stock and verify a green check mark on part label. If not present send part back to Mopar under RMA 8925-792 and replace with clean stock from Mopar. Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern.
104558
FCA Caribbean Warranty Newsletter – Volume 11, Issue 4
9100475
Key Fob Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern.
104557
Warranty Newsletter – Volume 11, Issue 4
21-030-25
Flash: Transmission Control Module(TCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P0607-00 - ECU Internal Performance. Customers may also experience the following: ● Blinking shifter and the inability to shift out of Park, or a no crank con This bulletin involves reprogramming the TCM with the latest available software
S2523000023
Trailer Tow Lights Inoperative. Diagnostic Trouble Codes (DTCs) B166E-13 B17AD-13 May Be Set.
08-095-25
Flash: Electronic Power Steering (EPS) Module Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C2217-00 - Electric Power Steering Module Internal. ● C221F-00 - ECU Not Initialized. ● C1592-00 - Electronic Power Steering Motor Circuit. ● C1593-00 - Steering Torque Sensor Circuit. Customers may also experience the following: ● Loss of steering assist and/or a steering warning light on in the Instrument Panel Cluster (IPC ) This bulletin involves updating the EPS module with the latest available software
S2408000015 REV.D
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
26B Combo Rev1
CUSTOMER SATISFACTION NOTIFICATION NORTH AMERICA 26B Thermostat
S2509000004
Misfire DTCs, Rough Idle, Valvetrain Noise
08-091-25
Flash: Radio Frequency Hub Module (RFHM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B1A10-00 - RKE FOB 1 Battery Low. ● B1A11-00 - RKE FOB 2 Battery Low. ● B23D7-14 - Gated Park Control - Circuit Short To Ground Or Open. Customers may also experience one or more of the following: ● **Uconnect app requests not functioning (none of the app functions work, lock/unlock, remote start).** ● Vehicle does not start. ● Passive Entry (PE) intermittently inoperative. ● Keyless Ignition Node (KIN) unresponsive. ● Welcome feature does not activate at times This bulletin involves inspecting and possibly updating the RFHM module with the latest available software.
104180
TRANSMITTER KIT & KEY KIT - INTEGRATED KEY FOB
S2508000014 REV.B
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
S2523000021
Power Liftgate Drive Unit (PDU) Servicing Information.
09-006-25
Engine Overheating Customers may experience the following: ● Engine overheating with "Engine Overheated" message in the Instrument Panel Cluster (IPC). NOTE: The vehicle will be operable but at a reduced level of performance. This bulletin involves replacing the engine thermostat.
9100532
MODULE Steering Control Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced.
S2508000022
Key Cannot be Programmed to The Vehicle
9100522
Ebooster When replacing the brake ebooster under warranty. Please return all associated parts which includes the snap rings so that the parts can be review by engineering.
S2508000020
Odometer Blinking, Security Gateway (SGW) Diagnostic Trouble Codes (DTCs) Diagnostics
S2508000008 REV.C
Battery Drained, Ignition Off Draw (IOD), Cluster Display Goes Off and On, and/or Door Lock Indicator Lamps Stay Illuminated
S2423000027 REV.C
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
S2508000014 REV.A
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
08-054-25 REV. A
Flash: Ignition System Control Module (ISCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P2C30-00 - Ignition Coil Primary Circuit Fuse A. ● P2C31-00 - Ignition Coil Primary Circuit Fuse B. ● P0300-00 - Multiple Cylinder Misfire. ● P0301-00 - Cylinder 1 Misfire Detected. ● P0302-00 - Cylinder 2 Misfire Detected. ● P0303-00 - Cylinder 3 Misfire Detected. ● P0304-00 - Cylinder 4 Misfire Detected. ● P0305-00 - Cylinder 5 Misfire Detected. ● P0306-00 - Cylinder 6 Misfire Detected. ● P0420-00 - Catalyst System Efficiency Below Threshold Bank 1. ● P0430-00 - Catalyst System Efficiency Below Threshold Bank 2. Customers may also comment on the following: ● Engine hesitates/misfires *This bulletin involves reprogramming the ISCM with the latest available software.**
S2509000002
Engine Noise
S258A000007
Radio Display Screen Flicker
S258A000009
Apple CarPlay Does Not Complete The First Initial Wireless Connection.
23-010-25
Power Running Board Trim Paint Peeling The customer may comment on the following: ● Power running board black trim paint peeling Fig. 1 and Fig. 2 This bulletin involves replacing one or both power running board steps as needed
08-054-25
Flash: Ignition System Control Module (ISCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P2C30-00 - Ignition Coil Primary Circuit Fuse A. ● P2C31-00 - Ignition Coil Primary Circuit Fuse B. ● P0300-00 - Multiple Cylinder Misfire. ● P0301-00 - Cylinder 1 Misfire Detected. ● P0302-00 - Cylinder 2 Misfire Detected. ● P0303-00 - Cylinder 3 Misfire Detected. ● P0304-00 - Cylinder 4 Misfire Detected. ● P0305-00 - Cylinder 5 Misfire Detected. ● P0306-00 - Cylinder 6 Misfire Detected. ● P0420-00 - Catalyst System Efficiency Below Threshold Bank 1. ● P0430-00 - Catalyst System Efficiency Below Threshold Bank 2. Customers may also comment on the following: ● Engine hesitates/misfires. This bulletin involves updating the ISCM with the latest available software This bulletin involves inspecting and possibly reprogramming the ISCM and the Powertrain Control Module (PCM) with the latest available software
S2123000084 REV.A
1st Row Seat Belt Retractor D-Ring Is Binding And Not Able To Rotate
S2223000069 REV.B
Rattle Noise From The Headliner Roof Area.
S2423000008 REV.A
SOS Button Inoperative And Or Unavailable. B1552-2A Code Set.
103287
HOUSING - A/C AND HEATER
S2108000015 REV.J
Uconnect Box Require Service Message
08-041-25
Flash: Integrated Trailer Control Module (ITCM) Updates ustomers may comment on the following: ● When driving the vehicle, the trailer brake gain screen will pop up in the Instrument Panel Cluster (IPC) for a few seconds (same screen that would pop up if you squeeze the trailer brake manual lever control under the steering wheel), however no activation is made by the driver at all. No additional brake power is applied to the vehicle during the pop up event. This bulletin involves updating the ITCM with the latest available softwar
102935
VALVE BODY & CONTROL UNIT - TRANSMISSION
103473
VALVE BODY & CONTROL UNIT - TRANSMISSION
102938
COOLER - AUXILIARY LOW TEMPERATURE
21-016-25
Valve Body Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U0101 - Lost Communication With The Transmission Control Module (TCM). ● U0402 - Implausible Data Received From TCM. ● U0418 - Implausible Data Received From Brake System Control Module 1. Customers may also comment on the following: ● Vehicle will go in limp-in mode. After limp-in mode, once in park the vehicle will not shift in gear. This bulletin involves replacing the Transmission Valve Body.
23-008-25
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S2219000005 REV.C
Check Engine Lamp On. Warning Messages In The Cluster. U0131 Lost Communication With Power Steering Control Module Set.
S228A000005 REV.E
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
S2508000014
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
103260
CENTER STACK - DISPLAY
102939
LATCH – FRONT & REAR DOOR
103228
SENSOR - BATTERY
S258A000004
DVD Or Blu-Ray INOP, Rear Screens Or Monitors INOP, VRM Audio INOP, Mirroring INOP
S2523000007
Trailer Brake Information Displays In Cluster With No Trailer Connected.
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S258A000001
Customer Unable To Use The Brand App To Remote Start Or Lock/Unlock Vehicle Doors
S258A000002
Radio Screen Goes Blank, Rearview Camera (RVC) Functions Normally
S2523000003
Door Latch, Handle And Ajar Additional Service Information.
S2423000051
2nd Row Seats Will Not Fold Forward When The Release Button Is Pressed And/Or Difficult To Relatch When Returning To The Seated Position.
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2310000003
The customer may experience an airbag light on or seat belt chime when buckled.
S2408000126
Diagnostic Trouble Code (DTC) B1A0A-00 Remote Keyless Entry (RKE) FOB 3 Performance
08-213-24 REV. A
Flash: Radio Frequency Hub Module (RFHM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● B1A10-00 - RKE FOB 1 Battery Low. ● B1A11-00 - RKE FOB 2 Battery Low. ● B23D7-14 - Gated Park Control - Circuit Short To Ground Or Open. Customers may also experience one or more of the following: ● Vehicle does not start. ● Passive Entry (PE) intermittently inoperative. ● Keyless Ignition Node (KIN) unresponsive. ● Welcome feature does not activate at times. This bulletin involves inspecting and possibly updating the RFHM module with the latest available software.
18-086-24
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0325 - Knock/Combustion Vibration Sensor "A" Circuit. ● P0330 - Knock/Combustion Vibration Sensor "B" Circuit. ● P0300 - Multiple Cylinder Misfire. (NA Market Only) ● P032A - Knock/Combustion Vibration Sensor "C" Circuit. ● P018B - Fuel Pressure Sensor "B" Circuit Rang/Performance. ● P1CEA - Boost Side EVAP Purge System Performance. (NA Market Only)** ● P00F3 - Humidity Sensor Circuit Range/Performance. ● P06DD - Engine Oil Pressure Control Circuit Performance/Stuck Off. ● P00C6 - Fuel Rail Pressure Too Low - Engine Cranking. Customers may also comment on one or more of the following: ● **Low oil pressure Instrument Cluster Panel (IPC) warning during heavy towing. ● Engine RPM dip below idle speed during coast down to idle.** ● Undesirable vehicle drivability behavior causing a vehicle Shift to Park event during Engine Stop Start (ESS) while Adaptive Cruise Control (ACC) is active. ● Idle speed oscillations observed when in Snow and Mud modes for vehicle configured with 4x2 drivetrain. ● Screen two incorrectly pops up on the IPC for five seconds during Terrain and Rock mode. ● Fully Autonomous Parking Assist (FAPA) is not deactivated when the accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezing temperatures. **The following software calibration improvements are also available: ● Engine mega knock detection. ● Misfire during cold start. ● Avoid false failures with MIL on. (NA Market Only)** This bulletin involves reprogramming the PCM with the latest available software.
S2302000001 REV. A
Service Air Suspension Message In Cluster. Ride Height Sensor and System Performance Diagnostic Trouble Code(s) (DTCs) In Below Freezing Temperatures.
S2402000002
Click Or Clicking Noise From Under Hood Near The Fast Down Leveling Valve.
S2423000012 REV.C
Power Liftgate Is Inoperative or Won’t Close.
S2408000119
Instrument Panel Cluster (IPC) message “Night Vision Unavailable Service Required” or Loss of Night Vision
101287
MODULE - TRANSFER CASE CONTROL
9100437
SHIFTER The service shifter message comes on in the cluster and the lever gets stuck in park "P" and it can be present the follwoing DTC: - U11E3 - TCM Lost communication with ESM on D-PT CAN - U0103 - Lost communication with Electric Gear Shift Module - U0101- Lost communication with DTCM - U0418 - Implausible Data Received From Brake System Control Module - U0402 - Implausible data received from TCM **NOTE: Prior any shifter replacement Refer to TSB-4582 2024-2025 WS - Valve Body Replacement. Recomended Diagnosis procedure: 1. Confirm if U0101 -Lost Communication with TCM or U0418 -Implausible Data Received From Brake System Control Module are present, if so check the Valve Body CAN Terminals any corrosion. 2. Check the wiring connectors between the ESM and the TCM and check voltage. 3. Check the pin header for the ESM for any bent pins. 4. If wiring and voltage are good and the DTCs (U11E3 - TCM Lost communication with ESM on D-PT CAN & U0103 - Lost communication with Electric Gear Shift Module) are still present, erase them with the scan tool. Reset ECU. 5. if DTCs for loss communication are still active at the ESM and you are still unable to shift then replace the Shifter module.
18-084-24
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. ● P1CEA-00 - Boost Side Evap Purge System Performance. ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/stuck Off. The following software update is also available: ● Poor AC performance in hot ambient temperatures. ● Engine speed display improvement for tachometer on the Instrument Panel Cluster (IPC) - smoother tachometer display (previous was too active). ● Prevent false fails with MIL on. This bulletin involves reprogramming the PCM with the latest available software.
S2424000012
Customer Indicates Rear Air Conditioning Is Blowing Much Warmer Than Front.
S2422000001 REV.C
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
08-190-24 REV. A
Flash: Central ADAS Decision Module (CADM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C008E - ECU Internal Performance. ● C2203-00 - Current VIN Missing/Mismatch. ● U015C-00 - Lost Communication With Automated Driving System Control Module "A". In addition, the customer may comment on one ore more of the following: ● Active Lane Management (ALM) settings do not save and turns "Off" between key-cycles. ● Adaptive Cruise Control (ACC) settings do not save between key-cycles. Defaults back to "4 Bars". ● "Automatic Emergency Braking (AEB) Unavailable Service Required" pop up intermittently on the Instrument Panel Cluster (IPC). ● "Active Lane Management (ALM) Unavailable Service Required" warning message appears on the IPC with no active fault codes. ● Blind Spot Monitoring (BSM) Warning Light LED "flickering" when activated. ● Traffic Sign Information (TSI) feature Indicator on the IPC "blinking" when driving past consecutive speed signs. This bulletin involves reprogramming of the CADM with the latest available software
18-081-24 REV.A
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. ● P1CEA-00 - Boost Side Evap Purge System Performance. ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/stuck Off. The following software update is also available: ● Engine speed display improvement for tachometer on the Instrument Panel Cluster (IPC) - smoother tachometer display (previous was too active). ● Prevent false fails with MIL on. This bulletin involves reprogramming the PCM with the latest available software
08-227-24
Flash: Electric Power Steering (EPS) Module Updates The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ● C2217-00 - Electric Power Steering Module Internal. ● C221F-00 - ECU Not Initialized. ● C1592-00 - Electronic Power Steering Motor Circuit. ● C1593-00 - Steering Torque Sensor Circuit. This bulletin involves updating the EPS module with the latest available software
08-230-24
R1H Radio U33.43 USB Software Update Customers may experience one or more of the following: ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally). This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio's current software level the radio may need a one or two USB update.
08-231-24
Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0C19 - Drive Motor A Torque Delivered Performance. ● P1B03 - Resolver Signal / MCPA Rationality. ● B273C - Digital Crash Input. Customers may experience the following: ● Intermittent Wrench (service HV) Condition. This bulletin involves reprogramming the HCP/AHCP, also known as Power Inverter Module (PIM), with the latest available software.
S2423000046
Buzz Squeak Rattle From Right Rear Headliner Area.
S2424000011
Customer Indicates Air Conditioning Is Blowing Warm.
101231
CARRIER – PLANETARY & SHAFT KIT - OUTPUT
18-081-24
Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): lP018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. lP1CEA-00 - Boost Side Evap Purge System Performance. lP06DD-00 - Engine Oil Pressure Control Circuit Performance/stuck Off. The following software update is also available: lEngine speed display improvement for tachometer on the Instrument Panel Cluster (IPC) - smoother tachometer display (previous was too active). lPrevent false fails with MIL on.
S2418000014
MIL or CEL Lamp On.
101095
Bracket - Fender Mounting
S248A000015
Poor Audio Quality And Or Static From Wireless Devices
18-056-24 REV. A
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. Customers may also comment on one or more of the following: ● Fully Autonomous Parking Assist (FAPA) is not deactivated when the accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezing temperatures This bulletin involves reprogramming the PCM with the latest available software.
S2408000016 REV.B
Front Passenger Side and Rear Window Door Window Switches are Inoperative, Window Operation Does Work from the Driver Master Switch
100635
VALVE BODY & CONTROL UNIT - TRANSMISSION
S2219000007 REV.A
Service Electric Power Steering (EPS) Message Displayed on Cluster Upon Start Up
S2408000112
Blind Spot Warning Message Displayed on the Cluster
S2319000005 REV.A
Customer Complaint Of Loss Of Power Steering Assist.
08-213-24
Flash: Radio Frequency Hub Module (RFHM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B1A10-00 - RKE FOB 1 Battery Low. ● B1A11-00 - RKE FOB 2 Battery Low. ● B23D7-14 - Gated Park Control - Circuit Short To Ground Or Open. Customers may also experience one or more of the following: ● Vehicle does not start. ● Passive Entry (PE) intermittently inoperative. ● Keyless Ignition Node (KIN) unresponsive. ● Welcome feature does not activate at times. This bulletin involves inspecting and possibly updating the RFHM module with the latest available software.
S2423000024 REV.B
Door Ajar Light On With Door(s) Closed.
S2403000005
Malfunction Indicator Lamp (MIL) Illumination And Service Transmission Message Displayed. Diagnostic Trouble Code (DTC) P0607-ECU Internal Performance, Set.
19-001-24
Damaged Inner Tie Rod Boots The technician or customer may notice the following: ● A twisted, dented, or otherwise damaged inner tie rod boot(s). This bulletin involves inspecting and possibly replacing the left and/or right inner tie rod boot(s)
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
08-202-24
Radio Over The Air Update to U33.43 Software Version (FOTA) Customers may experience one or more of the following: ● Unable to select the Turn by Turn Nav. ● Blank Performance Pages. Rearview Camera (RVC) functions normally. ● Android Auto® Voice Recognition Inop. ● Media Tuner Delayed. ● Charge Schedule HMI. RVC functions normally. ● Ambient Light Inop. ● Map in Cluster Inop. ● Media Widget Blank. ● Nav Map Black. ● Offroad Pages Inop. RVC functions normally. ● VR Inop. ● Incorrect Song Title Displayed, Carplay® only. ● HU switches from Media Page to Home Page. RVC functions normally. ● Ghost Touch on Nav screen. RVC functions normally. ● Widgets Missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the "Camera View Pages"". RVC functions normally. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from U29.42 to U33.43. NOTE: The national launch for the FOTA is expected to begin September 30, 2024.
9100409
TRANSFER CASE Before replacing a transfer case unit for fault codes C1444-98 and/or C1477-4B, be sure to reference TSB 21-048-24 for potential transfer case shift motor replacement
S2523000078
Liftgate Latch Is Tripped Closed During Service Work. How To Open The Latch.
21-048-24
Transfer Case Active Shift Motor Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C1444-98 - T-Case Motor Overuse-Component Or System Over Temperature. ● C1477-4B - Transfer Case Clutch-Over Temperature. Customers may also comment on the following: ● "4WD Overheated Temporarily Unavailable" message displayed in the Instrument Panel Cluster (IPC). This bulletin involves replacing the transfer case shift motor.
100079
WIRING - ELECTRIC POWER STEERING
S2418000010
MIL On/Check Engine Lamp On, Engine May Run Rough
08-190-24
Flash: Central ADAS Decision Module (CADM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C008E - ECU Internal Performance. ● C2203-00 - Current VIN Missing/Mismatch. ● U015C-00 - Lost Communication With Automated Driving System Control Module "A". In addition, the customer may comment on one ore more of the following: ● Active Lane Management (ALM) settings do not save and turns "Off" between key-cycles. ● Adaptive Cruise Control (ACC) settings do not save between key-cycles. Defaults back to "4 Bars". ● "Automatic Emergency Braking (AEB) Unavailable Service Required" pop up intermittently on the Instrument Panel Cluster (IPC). ● "Active Lane Management (ALM) Unavailable Service Required" warning message appears on the IPC with no active fault codes. ● Blind Spot Monitoring (BSM) Warning Light LED "flickering" when activated. ● Traffic Sign Information (TSI) feature Indicator on the IPC "blinking" when driving past consecutive speed signs. This bulletin involves reprogramming of the CADM with the latest available software.
99964
BEZEL - DOOR HANDLE
100040
CENTER STACK - VEHICLE FEATURE CONTROLS
9100401REV1
3.5" speaker assembly Before replacing a speaker part for crackles or rattling noises make sure to take the following steps: 1. Check for electrical harness routing too close to speaker's rear moving parts, improper connection, and/or harness pinch or damage. 2. Ensure no loose components, including trim grilles, fasteners, surrounding IP parts, etc. were found when removing the speaker. 3. Try "bad" speaker at another IP location and see if noise follows speaker. Try a different "good" speaker at "bad speaker location" and see if noise still happens at "bad" location. 4. Remove the bad speaker and replace it back. 5. If even with this verification and adjustments the speaker sounds bad, test the individual speaker with the audio files provided in the Service Library Homepage under "Reference Materials" prior to replacement. Follow all these steps, if issue still happens; reach out to the engineer at Stellantis for more support, if the engineer doesn t respond in 30 minutes. Then the speaker can be replaced.
9100401
3.5" speaker assembly Before replacing a speaker part for crackles or rattling noises make sure to take the following steps: 1. Check for electrical harness routing too close to speaker's rear moving parts, improper connection, and/or harness pinch or damage. 2. Ensure no loose components, including trim grilles, fasteners, surrounding IP parts, etc. were found when removing the speaker. 3. Try "bad" speaker at another IP location and see if noise follows speaker. Try a different "good" speaker at "bad speaker location" and see if noise still happens at "bad" location. If even with this verification and adjustments the speaker sounds bad, test the individual speaker with the audio files provided in the Service Library Homepage under "Reference Materials" prior to replacement.
S248A000013
After Radio Software Update, Pedestrian Emergency Brake (PEB) Lamp and Forward Collision Warning (FCW) Lamp on in Cluster or Other Customer Programable Features Concerns Not Set, No Diagnostic Trouble Codes (DTCs)
23-004-24 REV. A
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S2108000249 REV.C
Cluster and Radio Display Settings Revert Back to Default Settings, Auto Door Locks and Paddle Shifter Inoperative With No Menu to Enable, Pedestrian Emergency Brake (PEB) Lamp and Forward Collision Warning (FCW) Lamp on After a Recent Service Repair no Diagnostic Trouble Codes (DTCs)
S2423000030 REV.A
Buzz Squeak Rattle (BSR) From Upper Left Dash Area.
S2408000016 REV.A
Front Passenger, Rear right and/or Rear left Window Door Window Switches are Inoperative, Window Operation Does Work from the Driver Master Switch
18-063-24
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P06DD - Engine Oil Pressure Control Circuit Performance/Stuck Off. ● P00F3 - Humidity Sensor Circuit Range/Performance. Customer may also experience one or more of the following: ● Customers may experience coasting complaints at lower speed. ● Undesirable vehicle drivability behavior causing a vehicle Shift to Park event during Engine Stop Start (ESS) while Adaptive Cruise Control (ACC) is active. ● Pressing ACC button while ESS active can shift the vehicle to park. ● Idle speed oscillations observed when in Snow and Mud modes. ● Poor engine performance (undershoots engine speed) for ESS and for non-ESS engine start. ● Screen two incorrectly pops up on the Instrument Cluster Panel (IPC) for 5 seconds during Terrain and Rock mode. This bulletin involves reprogramming the PCM with the latest available software.
99500
CARRIER – PLANETARY & SHAFT KIT - OUTPUT
S2408000080
Different Cluster Displays Have a Reduced View While in Analog Mode, Darkened Sides
S2408000079
Low Battery, No Crank No Start, Cluster Message “Service Keyless System”, Intermittent Power Liftgate Operation
9100386
Security Gateway Module Battery Voltage - Circuit Voltage Below Threshold - DTC B2199-16 Repair Action : 1) Check OR Replacing cabling. 2) Check OR Replacing connector. 3) Check the battery is good OR Replacing battery. 4) Check OR Replacing FUSE. 5) Check SGW terminal. Battery Voltage - Circuit Voltage Above Threshold - DTC B2199-17 Repair Action : 1) Check OR Replacing cabling. 2) Check OR Replacing connector. 3) Check the battery is good OR Replacing battery. 4) Check OR Replacing FUSE. 5) Check SGW terminal. CAN Bus- [C-CAN1] (Node mute) or CAN Bus Off Performance- (Bus off failure) - Check DTC in DTC matrix Repair Action: 1) CAN Lines Check 2) Read Fault memory of all nodes 3) Check and download the right calibration file for current vehicle configuration Ethernet Bus Failure - Check DTC Repair Action: 1) CAN Lines Check 2) Read Fault memory of all nodes 3) Check and download the right calibration file for current vehicle configuration ECU-In-Plant-Mode - B235A-00 Repair Action: Install Calibration file with correct policy Ecu Internal Performance - Internal Electronic Failure - DTC B22A9-49 Repair Action: 1. If its in store clear and check again if DTC shows up. 2. Check battery voltage 3. Issue still exist then change ECU ECU Not Programmed / Flash Required (No Valid Application) - DTC C221C-00 Repair Action: 1. Reflash ECU with correct file Control Module Security Certificate Missing/Invalid - DTC U3033-00 or U3033-01 Repair Action: 1. Check connectivity 2. Ethernet network 3. Flash with the latest FOTA App Code 4. Flash the cert store with correct certificate 5. Clear Faults
9100388
BODY CONTROL MODULE After Battery Drainage BCM do not work. Please follow the following steps. 1. Check the BCM PROXI, if the BCM or any other modules are not aligned, then perform the PROXI alignment, reset the modules and perform normal ignition cycle (OFF to RUN to OFF) 2. If PROXI is correct (No misalignment), then reset the BCM module and perform normal ignition cycle. 3. Check for the DTC's and check wiring and components related to those DTC's and clear them
S2408000015 REV.C
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
9100364
Seat Control Module 3RD ROW SEAT WILL NOT CLOSE FULLY DOWN CUSTOMER STATES THE PASSENGER SIDE 3RD ROW WILL NOT CLOSE FULLY DOWN Steps for Tech: Before recalibrating 3rd row see please follow below mentioned steps first. -Turn off vehicle for 2 minute and then turn on vehicle and press 3rd row seat switch 2 times - Seat will start moving and relearn its correct hard stops and parameters. -Seat will recalibrate itself with updated SW.
S2408000066
Drained Battery, Low System Voltage, Battery Not Charging, High System Voltage
S2408000067
The Electronic Vehicle Information Center (EVIC) Displays Park Assist System Disabled Message
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2308000120 REV.B
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
18-055-24
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. ● P0300-00 - Multiple Cylinder Misfire. Customers may also comment on one or more of the following: ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezing temperatures. This bulletin involves reprogramming the PCM with the latest available software.
18-056-24
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. ● P0300-00 - Multiple Cylinder Misfire. Customers may also comment on one or more of the following: ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezing temperatures. This bulletin involves reprogramming the PCM with the latest available software.
S228A000005 REV.D
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
S2307000002 REV.B
Suspected Engine Coolant Leak
9100355
Video Router After Battery Drainage VRM do not work. Please follow the following steps. 1. Check VRM proxi, if the VRM is not aligned, perform proxi alignment, reset module. 2. If proxi is correct, reset module 3. Check for DTCs, and check wiring and components related to those DTCs and clear them.
S2423000030
Buzz Squeak Rattle (BSR) From Upper Left Dash Area
S2223000044 REV.B
Power Side Steps Reverse, Stop In Motion, Do Not Deploy Or Stow, And May Have a Chirp Noise.
9100345
Latch, Front Door For doors that won't open from fnterior, cable dislodged or door latch cables coming loose. Engineering is looking to collect pictures of the latches and cables as they are found by the dealers. These pictures will help us understand why they are coming lose, to develop a corrective action plan. Please submit pictures to the DID system.
S2408000048 REV.A
Comfort Seat Module (CSM) or Comfort Steering Wheel Module (CSWM) do Not Operate After a Recent Module Replacement
S2423000019 REV.A
Water Leaking Into Interior At D-Pillar Or Liftgate
47B Combo
Customer Satisfaction Notification 47B Oil Pump
08-124-24
Flash: Air Suspension Control Module (ASCM) Updates Customers may experience: ● After towing a heavy load above the protection limit, the air suspension will only lower and will remain in low ride height. Instrument Panel Message (IPC) message "selected ride height not permitted due to payload" appears. This bulletin involves reprogramming the ASCM with the latest available software.
23-032-24
Left Rear Door Trim Panel Defective Customers may experience the following: ● Rear left hand door panel might show broken plastic on the bottom of the door or nearby the map pocket. ● Rear left hand door panel to door attachments or component attachments may break. This bulletin involves replacing the rear left hand door panel.
S2408000048
Comfort Seat Module (CSM) or Comfort Steering Wheel Module (CSWM) do Not Operate After a Recent Module Replacement
9100344
VALVE BODY & CONTROL UNIT Transmission Ensure clutch pressure check has been completed and documented prior to valve body replacement.
S2307000002 REV.A
Suspected Engine Coolant Leak
S2408000015 REV.B
Remote Keyless Entry (RKE) Button Functions Does Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed
S2208000060
Low Fuel Warning Indicator Stuck ON
S2223000022
Power Liftgate Inoperative Or Intermittently Will Not Open Or Close.
9100269
Air Spring For air suspension related concerns when a leak is suspected DO NOT replace airspring or other components;~ first reference SOL S2202000013. ~ Verify lines are fully seated in air springs and no leaks present. If airspring replacement is necessary, DO NOT replace multiple airsprings at once.
0800824A
Radio Over The Air Update to U29.42 Software Version Customers may experience one or more of the following: ? Blank phone widget displayed. ? Radio freeze after reverse event (Rearview Camera (RVC) Functions Normally). ? Screen Off at start up (RVC Functions Normally). ? Radio restart before sleep after switching between different USBs. ? Pop up error "setting not saved" occurring when attempting to enable Geolocation (Privacy Mode Off). ? Amplifier module sets Diagnostic Trouble Code (DTC) U0485 Implausible Data Received From Radio. ? During FOTA Scheduling, if OK is not pressed to confirm time selected, vehicle will sleep. ? Apps downloaded for one connected profile are being shared with other local profiles. ? Switching profiles with slow response. ? Slow response switching between camera views. ? Black radio screen (RVC functions normally). ? Rear seat reminder alert unavailable. ? Wi-Fi software update pop-up is being triggered in non-connected vehicles. ? Switching to Android menu, display screen blinks on green color. ? Microphone inoperative during SOS call from the vehicle. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from T27.39 or U29.28 to U29.42. NOTE: The national launch for the FOTA is expected to begin **February 16, 2024.**
S2123000032
Rattle Buzz Noise From Door Area
S2408000005
Vehicle Staying Awake Intermittently Causing Battery Drain, BCM DTC B23D7-14 Gated Park Control-Circuit Short to Ground or Open
9100287
Thermostat Assy For 2022-2024MY 3.6L Pentastar Upgrade with P0128 failure code. PRIOR TO PERFORMING ANY THERMOSTAT REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2309000014
0800624A
Navigation (NAV) Reboot When MOTA Fails The customer may describe one of more of the following: ? Radio navigation continues to reboot after a Map Update (MOTA). ? Navigation regularly cuts out and back on again. ? Radio switches to navigation without customer's input. This bulletin involves updating the Navigation maps via USB.
2300424
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S2408000002
Tire Pressure Warning Lamp is on Steady, or Flashing
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
0800824
Radio Over The Air Update to U29.42 Software Version Customers may also experience one or more of the following: ? Blank phone widget displayed. ? Radio freeze after reverse event (Rearview Camera (RVC) Functions Normally). ? Screen Off at start up (RVC Functions Normally). ? Radio restart before sleep after switching between different USBs. ? Pop up error "setting not saved" occurring when attempting to enable Geolocation (Privacy Mode Off). ? Amplifier module sets Diagnostic Trouble Code (DTC) U0485 Implausible Data Received From Radio. ? During FOTA Scheduling, if OK is not pressed to confirm time selected, vehicle will sleep. ? Apps downloaded for one connected profile are being shared with other local profiles. ? Switching profiles with slow response. ? Slow response switching between camera views. ? Black radio screen (RVC functions normally). ? Rear seat reminder alert unavailable. ? Wi-Fi software update pop-up is being triggered in non-connected vehicles. ? Switching to Android menu, display screen blinks on green color. ? Microphone inoperative during SOS call from the vehicle. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from T27.39 or U29.28 to U29.42. NOTE: The national launch for the FOTA is expected to begin January 22, 2024
S238A000058
Radio Navigation Displays Message ?No Maps Available?
9100278
Radio Frequency Hub Symptom/Vehicle Issue: Remote Keyless Entry (RKE) And Remote Start Range Is Limited. B1A76-11 Remote Start Antenna Short To Ground Is Setting Erroneously. Please reference SOL S2308000145 before replacing the module. If you still feel that replacement is necessary FCA REDACTED CONTENT before replacing the module. If no response within 15 minutes, proceed with repair.
S238A000057
Audio Crackling Noise From Radio On Any Audio Source
S2309000013
Verifying Camshaft Diagnosis
S2323000083
Buzz Squeak Rattle (BSR) From Interior Near Rear Header D Pillar With Body Twist Or Over Bumps.
S238A000055
Audio Muted During A CarPlay Or Android Auto Phone Call
S2309000011
Customer may complain "Service Engine ? See Dealer" message displays in cluster
S2318000005
Customer?s complaint may include a message appearing in the cluster?s information center stating, ?See User?s Manual For Proper Oil And Fuel? or ?Service Engine See Dealer?.
9100252
LR DVD Video Screen For complaints of a non-functional (inop) LR seatback monitor, please contact FCA Redacted Content prior to ordering the part. If no response is received in 15 minutes, proceed with the repair.
S2308000123
No crank/No start with no DTC?s
S2309000010
Customer complaint may include a noise from under the hood described as a ?belt-related? noise.
S2308000125
Vehicle sunroof will not operate and 3rd row seat switches will not illuminate.
S2308000122
Vehicle is a no crank/no start with the following DTCs, as well as a no crank/no start condition: U0164, U0140, U0151, U0155
S2308000120
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
S238A000046
Maps Over The Air (MOTA) Is Causing The Navigation App To Continuously Reboot Or Map loading Screen Shown
9100157
Central ADAS Decision Module CADM LO Part Number is more precise than "Up to and including" and "After" dates in the item description. Please ensure to order the correct CADM and Long Range Camera Part Number(s) the vehicle was built with. The Root of the Original and Replacement part should be identical, the difference will be in the NIK level. Technician Removal of the Long Range Camera and CADM for Testing Purposes: Please ensure the root of the Original and Replacement part are identical.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
S2323000075
2nd Row Center Seat Lazy Or Slow When Folding.
0821623A
Email to Warranty Area Managers for a Warranty Bulletin D-23-18 applicable to 28 select dealers only regarding this and use of TSB 08-216-23
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
S2319000008
Clicking Noise From Steering Column While Turning Steering Wheel.
0821623
Battery No Start, Jump Start, Tow-In Complaints Customer may experience one or more of the following: ? No start, jump start, or tow-in. ? Engine Stop Start (ESS) is inoperable.
S2208000011
Wireless Qi Charger Not Charging
S2323000069
3rd Row Seat Shakes Or Vibrates When Folding.
9100217
Motor, Power Running Board For issues with a stuck or binding power side step, DO NOT replace the motor or hinge(s). The hinges must be cleaned and lubricated at regular intervals. See latest version of Star Online #S2223000044, the vehicle owner's manual, or published service information in Service Library. Replacements of the motor and hinge assembly due to lack of maintenance could be subject to chargeback.
S2317000001
Buzz Squeak Rattle (BSR) From Rear Of Vehicle On Rough Road Or Over Bumps.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100204
SENSOR, Battery Please call FCA Redacted Content prior to replacement. This part should not be replaced unless there is physical damage to the part or Code B2193 is present. If no response in 15 minutes, proceed with repair.
2400623
A/C Diagnostic LOP Change
S2223000078
Interior Dust Intrusion In Rear Cargo Area.
S2223000027
Buzz Rattle Squeak Noise From Under Hood
S2323000066
Buzz Squeak Rattle (BSR) From Left Rear Cargo Area Near Subwoofer.
S2323000067
Buzz Squeak Rattle (BSR) In The Door When Playing Music.
92776
Warranty Bulletin D-21-18 Wagoneer Service Action Additional Reimbursement (Rev. E)
9100190
Rear Window Sunshade For Rear door sunshade wrinkles. Once extended, if the sunshade is offset (Cocked) while retracting it, wrinkles go into the fabric but will go away after extended periods of being open and can also be expedited by applying heat/steam. Component replacement is not required
9100183
Amplifier Engineering is investigating radio audio cuts in and out or audio is muted on some speakers or audio is muted on all speakers with no sound from radio or speakers. Please perform an A-B-A swap analysis on Amplifier/Radio. Contact Engineering at FCA Redacted Content with results before replacing Amplifier/Radio. If no response in 15 minutes, proceed with repair.
0700723
Water Quality When Mixed With Engine Coolant
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.