9100900
Service Bulletin/Repair Instructions
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
9100900
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
9100363 Rev 3
Turbocharger Kit Please note that many turbo components are serviceable separately and full turbo replacement may not be required. If the turbo is being inspected for: Noise/Rattle: Inspect heat shield fasteners for looseness and check the wastegate actuator/linkage for binding. The actuator kit is serviced separately. Oil Leak: Inspect the turbo oil feed O-ring area for leaks. O-ring is serviced separately.
114044
D-25-15 Rev. C Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
114045
ID-25-11 Rev. C Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
16C Combo Rev3
EMISSION RECALL – NORTH AMERICA Check Engine/Malfunction Indicator Lamp 16C The instrument panel cluster on about 32,587 of the above vehicles may have an inoperable check engine/malfunction indicator lamp (CEL/MIL). (JT) vehicles: CEL/MIL and cargo lamp indicator function are swapped. (JL) vehicles: CEL/MIL will not turn on. The CEL/MIL in and of itself will not affect emissions. However, if there was an emission issue that would require illumination of the CEL/MIL, the customer would not be alerted. The vehicle would be non-compliant to the OBD II regulation.
113270
CORE – HEATER
113271
CORE – HEATER
08-260-26
Flash: Integrated Dual Charging Module (IDCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation SYMPTOM: the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● **B22A9-87 - ECU Internal Performance - Missing Message. ● P0D21-00 - Battery Charger "A" Output Voltage Too Low.** ● B22A9-16 - ECU Internal Performance-Circuit Voltage Below Threshold. ● B22A9-17 - ECU Internal Performance-Circuit Voltage Above Threshold. ● B22A9-19 - ECU Internal Performance - Overcurrent. ● B22A9-64 - ECU Internal Performance-Signal Plausibility Failure. ● P0D27-00 - Battery Charger 1 Input Voltage Too Low. Customers may also comment on one or more of the following: ● Unable to charge the vehicle with level 2 charger. ● Vehicle would not charge and the charge station circuit breaker in the house / receptacle trips when its plugged into the vehicle. **This bulletin involves reprogramming the IDCM with the latest software available.**
112639
THROTTLE BODY – NONE
112640
THROTTLE BODY – NONE
112862
MOTOR - BLOWER WITH WHEEL
112863
MOTOR - BLOWER WITH WHEEL
112842
BOLT - HEX FLANGE HEAD
21-041-26 REV. A
Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set **one or more the following Diagnostic Troubles Code (DTCs): ● U0287-00 - Lost Communication With Transmission Fluid Pump Module 1.** ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode. This bulletin involves replacing the transmission oil pump.
112856
HEATER - ELECTRIC COOLANT
112857
HEATER - ELECTRIC COOLANT
08-238-26
Fuel Oil Refresh Mode (FORM) Message - Safety Recall 68C Supplement Technicians may experience the following: ● A FORM message will display in the Instrument Panel Cluster (IPC) after performing RC-682-25 - Safety Recall 68C - High Voltage Battery
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
111760
MOTOR AND LINKAGE - WINDSHIELD WIPER
21-041-26
Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode This bulletin involves replacing the transmission oil pump.
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
08-072-26 REV. A
High Voltage Battery Pack Replacement XU1 Warranty Extension Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0BBE-00 - Hybrid Battery Pack Voltage Variation. ● P1C5E-00 - Battery State Of Health Failed. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P0B28-00 - Hybrid/EV Battery "B" Voltage Unstable. NOTE: ● Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage. ● Battery packs may contain cells with separator damage. Customers may comment on the following: ● “Service Charging System” message displayed in the Instrument Panel Cluster (IPC) and charging is inhibited This bulletin involves replacing the high voltage battery pack.
9100802
Before replacing the PIM, please check if the HV DC Connector is seated properly on the PIM and Battery control module. Reference: S2108000121 - Rev. B
9100787Rev1
Before replacing High voltage harness, please note the connector bolt and connector seal is available for replacement. Please see below for Connector bolt and seal part number available. Reference SOL S2608000019
S2608000019
High Voltage Connector Seal And Fastener Service Parts Are Now Available
9100787
Before replacing High voltage harness, please note the connector bolt and connector seal is available for replacement. Please see below for Connector bolt and seal part number available. Reference SOL S2608000019
S2623000018
Wind Noise From Hard Top Freedom Panels Near Rear View Mirror While Driving.
08-133-26
Rear Defroster Inoperative Customers may experience one or more of the following: SYMPTOM: ● Rear window is not defrosting. ● The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
16C Combo REV2
Emissions Recall 16C - Check Engine/Malfunction Indicator Lamp - Dealer Notification (Revision 2)
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
110770
D-26-06 Rev. A (XU1) High Voltage Battery Pack - Select 2021-2025 Jeep Wrangler (JL) and 2022-2026 Jeep Grand Cherokee/ Grand Cherokee (WL)
110771
ID-26-06 Rev. A (XU1) High Voltage Battery Pack - Select 2021-2025 Jeep Wrangler (JL) and 2022-2026 Jeep Grand Cherokee/ Grand Cherokee (WL)
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
110399
HANDLE - INSIDE RELEASE
110400
HANDLE - INSIDE RELEASE
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
31-001-26 REV.A
Door Hem Aluminum Body Panel Corrosion Repair Customers may experience the following: SYMPTOM: ● Filifom corrosion at the hem area of the door. This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.
110462
D-25-15 Rev. B Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
110469
ID-25-11 Rev. B Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
08-072-26
High Voltage Battery Pack Replacement XU1 Warranty Extension Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0BBE-00 - Hybrid Battery Pack Voltage Variation. ● P1C5E-00 - Battery State Of Health Failed. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P0B28-00 - Hybrid/EV Battery "B" Voltage Unstable. NOTE: ● Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage. ● Battery packs may contain cells with separator damage. Customers may comment on the following: ● “Service Charging System” message displayed in the Instrument Panel Cluster (IPC) and charging is inhibited. This bulletin involves replacing the high voltage battery pack.
110391
D-26-06 (XU1) High Voltage Battery Pack - Select 2021 - 2025 Jeep Wrangler (JL) and 2022 - 2026 Jeep Grand Cherokee/ Grand Cherokee (WL)
110409
ID-26-06 (XU1) High Voltage Battery Pack - Select 2021 - 2025 Jeep Wrangler (JL) and 2022 - 2026 Jeep Grand Cherokee/ Grand Cherokee (WL)
110429
Warranty Newsletter – Volume 12, Issue 2
110431
FCA Caribbean Warranty Newsletter – Volume 12, Issue 2
31-001-26
Door Hem Aluminum Body Panel Corrosion Repair Customers may experience the following: SYMPTOM: ● Filifom corrosion at the hem area of the door. This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.
16C Combo REV1
EMISSION RECALL – NORTH AMERICA Check Engine/Malfunction Indicator Lamp Reference: 16C
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2408000024 REV.B
Power Top Switch Unresponsive, Full Retractable Sky Roof Does Not Open or Close
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
9100756
DO NOT REPLACE MULTIPLE SHOCKS UNLESS ALL ARE VERIFIED TO BE DEFECTIVE. Reference Master Tech article released in January 2026 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm
S2108000121 REV.B
Check Engine Light On And Service Hybrid System Displayed. P0A0A-00 High Voltage System Interlock Circuit “A” Is Active
08-036-26
Flash: Battery Pack Control Module (BPCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● **P0B28-00 - Hybrid/EV Battery “B” Voltage Unstable. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0AA1 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0C78 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6 - Hybrid/EV Battery Charging Current High. ● P0B24 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E - Hybrid/EV Battery State Of Health Failed.** ● P1A21-00 - HV Battery Contactor Control Sequence Incorrect. ● P0B3E-00 - Hybrid/EV Battery Voltage Sense 1 Circuit High. ● P0607-00 - ECU Internal Performance. ● P1E1B-00 - Hybrid/EV Battery Side Voltage System Isolation. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. ● P1C00-00 - Hybrid/EV Battery Voltage Sense 1 Out Of Range Low. ● P1C01-00 - Hybrid/EV Battery Voltage Sense 1 Out Of Range High. ● P1A9B-00 - Hybrid/EV Battery Temperature Sensor 1 Out Of Range High. ● P0BBD-00 - Hybrid Battery Pack Voltage Variation Exceeded Limit. ● P167B-00 - Controlled System Shutdown. ● U1885-00 - Battery Energy Control Module Lost Communication With HCP. ● P0EDD-00 - Hybrid/EV Battery Pack B Deterioration. ● U0111 - Lost Communication With Hybrid Battery Pack Sensor Module. ● P0CA7-00 - Hybrid/EV Battery Discharging Current High. ● P1A0C-00 - Battery Energy Control Module System Voltage Low. J08 FSAR-TSB-6892 -2- **Customers may also comment on the following: ● Vehicle does not start. NOTE: The no start condition is accompanied with the following DTCs: P0DAB-00, P0607-00, P0AA1, P0AA4, P0C78, P0CA6, P0B24 and/or P1C5E. P0B28 will result in a MIL for 49 days. After 49 days of the MIL, the vehicle will no longer be allowed to start.** This bulletin involves reprogramming the BPCM with the latest available software. NOTE: Additional module flashes are requ
109820
SEAL - ROOF RAIL
109822
SEAL - ROOF RAIL
109281
CENTER STACK – NONE
109223
BEZEL - INSTRUMENT PANEL
109224
DOOR - PASSENGER AIR BAG
18-109-25
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: ● P2450 - Fuel Tank Isolation Valve Stuck Open. ● P1D83 - Implausible Engine Oil Temperature Signal Received. Customers may comment on one or more of the following: ● Fuel Door will not open due to intermittent Fuel Tank Isolation Valve (FTIV) Stuck Open. ● Reduced fuel efficiency. In addition, the following software enhancement is available: ● Hood Switch changes. This bulletin involves reprogramming the PCM, HCP and AHCP, also known as the Power Inverter Module (PIM) with the latest available software
16C Combo
Check Engine/Malfunction Indicator Lamp 16C
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
S1819000004 REV.R
Shimmy Felt In Front End
108544
SWITCH - POWER WINDOW
108655
D-25-15 Rev. A Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
108657
ID-25-11 Rev. A Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
108463
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108464
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
S1805000006 REV.B
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
9100684
When servicing/replacing 68415437A$ Transmission, take care to not damage the PIM to P2 harness. Also, when reinstalling the harness, route the harness properly and secure it at all the retention points.
105646
MODULE - STEERING CONTROL & COLUMN
9100325 Rev 1
Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.
08-314-25
Flash: Amplifier (AMP) Diagnostic and System Updates *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● B143B-12 - ANC Microphone 1-Circuit Short To Battery. ● B143C-12 - ANC Microphone 2-Circuit Short To Battery. ● B143E-12 - ANC Microphone 3-Circuit Short To Battery. ● B143F-12 - ANC Microphone 4-Circuit Short To Battery. NOTE: The DTCs are wrongly set and do not affect Active Noise Cancellation (ANC) performance This bulletin involves updating the AMP with the latest available software.
S2218000003 REV.B
Customer complaint may include a Mil On/Check Engine Lamp On and Electronic Throttle Control (ETC) Lamp On. There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
21-038-25
Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode This bulletin involves replacing the transmission oil pump.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
08-229-25
Flash: Radio Frequency Hub Module (RFHM) Updates Customers must experience the following: ● Customers may be concerned about vehicle theft due to ability of key FOBs to be programmed through RFHM. Software enhancement includes: ● Update to the RFHM software to prevent unauthorized keyfob programming. ● This is intended to deter an unwanted drive off of the vehicle without the customer's knowledge. This bulletin involves updating the RFHM module with the latest available software.
S2422000001 REV.D
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
09-018-25
Engine Cylinder Block Porosity Inspection - Engine Cold Start Rough Idle Customers may experience the following: ● Rough engine idle when cold starting the engine. ● Low coolant level in coolant recovery bottle.
105648
MODULE - ENGINE CONTROLLER
9100627
To inform dealers about the 850RE valve body PN: R8348504A connector: the original 16-pin connector included six pins that were not used in this application. To simplify the design, the connector has been optimized and updated to a 10-pin configuration.
9100624
Verify Reman part number availability. Order the "R" part number for all orders:
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100622
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
9100605
Shim - felt GIM # NUSENGCHR24018991: JL JT sun visor center support BSR. Add felt shim 68736674AA - 43MM OD x 10mm ID x 1mm thick.
S2408000024REVA
Power Top Switch Unresponsive, Full Retractable Sky Roof Does Not Open or Close Customer Complaint/Technician Observation: The owner complains the top system is inoperative and that by pressing the switches the Power Top does not make any movement. Technician may or may not have Diagnostic Trouble Codes (DTCs). Repair Procedure: Perform the power top calibration prior to any switch or parts replacement.
9004003
Backlite Heated Liftgate Glass Assembly: For rear window defrost inoperative concerns where heated glass electrical tab has become detached, it is not necessary to replace the glass assembly. For loose or detached electrical tab, refer to TSB 23-007-25 for repair procedures on reattaching a loose tab. For burned or discolored gridlines on hard tops, DO NOT change the complete Flipper glass assembly. This discoloration is oxidation of the ceramic silver material and is normal. The Engineering standard call out the fact that this bus bar will change in color and is not a deterioration of the material or performance.
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
S258A000013
AM Radio Static, With No Active or Stored Radio Antenna Diagnostic Trouble Codes (DTC).
9100547
Telematics Box Module Verify Z part number availability. Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only.
08-082-25 REV. A
High Voltage Wiring Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B273C-00 - Digital Crash Input. ● U0287-00 - Lost Communication With Transmission Fluid Pump Module 1. Customers may also experience one or more of the following: ● Vehicle shakes during a cold start. ● Noise is heard from the underbody near the P2 motor. This bulletin involves repairing the High Voltage (HV) cable harness to the Power Inverter Module (PIM)
104558
FCA Caribbean Warranty Newsletter – Volume 11, Issue 4
104557
Warranty Newsletter – Volume 11, Issue 4
21-007-25
Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters This bulletin involves reprogramming the TCM with the latest available software.
08-098-24 REV. A
Flash: Battery Pack Control Module (BPCM) Enhancements Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● **P0DAB - Hybrid/EV Cell Balancing Performance.** ● P0AA4 - Hybrid/EV Battery Negative Contactor 'A' Circuit Stuck Closed. ● P0AA1 - Hybrid Battery Positive Contactor Circuit Stuck Closed. ● P0CA6 - Hybrid/EV Battery Charging Current High. ● P0B24 - Unstable Hybrid Battery ‘A’ Voltage. ● P1C5E - Battery State or Health Failed. ● P0BBE - No Start - Loss or Reduction of Propulsion. ● P0607-00 - ECU Internal Performance. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. This bulletin involves reprogramming the BPCM with the latest software available. NOTE: Additional module flashes are required for this update to be effective, the following modules are all to be updated along with this BPCM update. ● Powertrain Control Module (PCM). ● Transmission Control Module (TCM). ● Integrated Dual Charging Control Module (IDCM). ● Hybrid Control Processor (HCP), Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM)
21-024-24 REV. A
Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. **The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters.** **This bulletin involves reprogramming the TCM with the latest available software.** NOTE: **Please be sure that the 04B recall is completed prior to performing this TSB. This TCM software update is covered by the 04B recall if still incomplete.**
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
2400623
A/C Diagnostic LOP Change
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
9100142
Mirror
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9100008
Telematic box module 2
9100096
Base Headlamp Bright, Base Headlamp Black
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2108000198
Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit
S2108000181RevA
Media Hub And Or Wireless Charging Pad Is Inoperative
S2108000181a
Media Hub And Or Wireless Charging Pad Is Inoperative
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
75745
HUB AND BEARING - WHEEL
75610
BASE - FLOOR CONSOLE
75567
LATCH - FRONT DOOR
75490
CAMSHAFT - INTAKE
75227
MUFFLER AND TAILPIPE ? EXHAUST
75446
GLASS - SUNROOF
75267
TUBE - TURBO WATER FEED
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S2124000004
A/C does not cool and vehicle is low on Freon charge but no leak is found with sniffer or black light anywhere in the system
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.