S2609000011
Service Bulletin/Repair Instructions
MIL-On and/or Engine Oil Leak
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2609000011
MIL-On and/or Engine Oil Leak
9100900
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
9100363 Rev 3
Turbocharger Kit Please note that many turbo components are serviceable separately and full turbo replacement may not be required. If the turbo is being inspected for: Noise/Rattle: Inspect heat shield fasteners for looseness and check the wastegate actuator/linkage for binding. The actuator kit is serviced separately. Oil Leak: Inspect the turbo oil feed O-ring area for leaks. O-ring is serviced separately.
114044
D-25-15 Rev. C Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
114045
ID-25-11 Rev. C Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
113270
CORE – HEATER
113271
CORE – HEATER
9100833 REV1
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S2508000025 REV. B
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
08-262-26
Flash: Integrated Dual Charging Module (IDCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation SYMPTOM: the technician may find one or more of the following Diagnostic Trouble Code (DTC) have been set: ● B22A9-87 - ECU Internal Performance - Missing Message. ● P0D21-00 - Battery Charger "A" Output Voltage Too Low. Customer may also experience the following: ● Vehicle will not charge. This bulletin involves reprogramming the IDCM with the latest software available.
112639
THROTTLE BODY – NONE
112640
THROTTLE BODY – NONE
S2508000025 REV.A
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
112862
MOTOR - BLOWER WITH WHEEL
112863
MOTOR - BLOWER WITH WHEEL
112842
BOLT - HEX FLANGE HEAD
21-041-26 REV. A
Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set **one or more the following Diagnostic Troubles Code (DTCs): ● U0287-00 - Lost Communication With Transmission Fluid Pump Module 1.** ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode. This bulletin involves replacing the transmission oil pump.
9100833
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S268A000014
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
112856
HEATER - ELECTRIC COOLANT
112857
HEATER - ELECTRIC COOLANT
08-238-26
Fuel Oil Refresh Mode (FORM) Message - Safety Recall 68C Supplement Technicians may experience the following: ● A FORM message will display in the Instrument Panel Cluster (IPC) after performing RC-682-25 - Safety Recall 68C - High Voltage Battery
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
111760
MOTOR AND LINKAGE - WINDSHIELD WIPER
21-041-26
Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode This bulletin involves replacing the transmission oil pump.
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
111833
SENSOR – KNOCK
111834
SENSOR – KNOCK
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
08-072-26 REV. A
High Voltage Battery Pack Replacement XU1 Warranty Extension Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0BBE-00 - Hybrid Battery Pack Voltage Variation. ● P1C5E-00 - Battery State Of Health Failed. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P0B28-00 - Hybrid/EV Battery "B" Voltage Unstable. NOTE: ● Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage. ● Battery packs may contain cells with separator damage. Customers may comment on the following: ● “Service Charging System” message displayed in the Instrument Panel Cluster (IPC) and charging is inhibited This bulletin involves replacing the high voltage battery pack.
9100802
Before replacing the PIM, please check if the HV DC Connector is seated properly on the PIM and Battery control module. Reference: S2108000121 - Rev. B
9100787Rev1
Before replacing High voltage harness, please note the connector bolt and connector seal is available for replacement. Please see below for Connector bolt and seal part number available. Reference SOL S2608000019
S2608000019
High Voltage Connector Seal And Fastener Service Parts Are Now Available
9100787
Before replacing High voltage harness, please note the connector bolt and connector seal is available for replacement. Please see below for Connector bolt and seal part number available. Reference SOL S2608000019
S2623000018
Wind Noise From Hard Top Freedom Panels Near Rear View Mirror While Driving.
08-133-26
Rear Defroster Inoperative Customers may experience one or more of the following: SYMPTOM: ● Rear window is not defrosting. ● The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window.
08-120-26
Flash: Comfort Seat Wheel Module (CSWM) Update Customers may experience the following: SYMPTOM: ● Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
110770
D-26-06 Rev. A (XU1) High Voltage Battery Pack - Select 2021-2025 Jeep Wrangler (JL) and 2022-2026 Jeep Grand Cherokee/ Grand Cherokee (WL)
110771
ID-26-06 Rev. A (XU1) High Voltage Battery Pack - Select 2021-2025 Jeep Wrangler (JL) and 2022-2026 Jeep Grand Cherokee/ Grand Cherokee (WL)
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
23-005-26
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: SYMPTOM: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
110399
HANDLE - INSIDE RELEASE
110400
HANDLE - INSIDE RELEASE
S2603000001
A suspected leak may be noticed on the front or rear axle pinion seal.
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
31-001-26 REV.A
Door Hem Aluminum Body Panel Corrosion Repair Customers may experience the following: SYMPTOM: ● Filifom corrosion at the hem area of the door. This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.
S228A000025 REV.A
Harman R1H Uconnect 5 Radio Software Flash Error Codes
110462
D-25-15 Rev. B Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
110469
ID-25-11 Rev. B Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
08-072-26
High Voltage Battery Pack Replacement XU1 Warranty Extension Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0BBE-00 - Hybrid Battery Pack Voltage Variation. ● P1C5E-00 - Battery State Of Health Failed. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P0B28-00 - Hybrid/EV Battery "B" Voltage Unstable. NOTE: ● Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage. ● Battery packs may contain cells with separator damage. Customers may comment on the following: ● “Service Charging System” message displayed in the Instrument Panel Cluster (IPC) and charging is inhibited. This bulletin involves replacing the high voltage battery pack.
110391
D-26-06 (XU1) High Voltage Battery Pack - Select 2021 - 2025 Jeep Wrangler (JL) and 2022 - 2026 Jeep Grand Cherokee/ Grand Cherokee (WL)
110409
ID-26-06 (XU1) High Voltage Battery Pack - Select 2021 - 2025 Jeep Wrangler (JL) and 2022 - 2026 Jeep Grand Cherokee/ Grand Cherokee (WL)
110429
Warranty Newsletter – Volume 12, Issue 2
110431
FCA Caribbean Warranty Newsletter – Volume 12, Issue 2
S2423000027 REV.D
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
31-001-26
Door Hem Aluminum Body Panel Corrosion Repair Customers may experience the following: SYMPTOM: ● Filifom corrosion at the hem area of the door. This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2408000024 REV.B
Power Top Switch Unresponsive, Full Retractable Sky Roof Does Not Open or Close
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
9100756
DO NOT REPLACE MULTIPLE SHOCKS UNLESS ALL ARE VERIFIED TO BE DEFECTIVE. Reference Master Tech article released in January 2026 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm
S2108000121 REV.B
Check Engine Light On And Service Hybrid System Displayed. P0A0A-00 High Voltage System Interlock Circuit “A” Is Active
109607
CALIPER ASSEMBLY - DISC BRAKE
08-039-26
Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0B28-00 - Hybrid/EV Battery “B” Voltage Unstable. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0607-00 - ECU Internal Performance. Customers may also comment on the following: ● Vehicle does not start. NOTE: The no start condition is accompanied with the following DTCs: P0DAB-00, P0607-00, P0AA1-00, P0AA4-00, P0C78-00, P0CA6-00, P0B24-00 and/or P1C5E-00. P0B28-00 will result in a MIL for 49 days. After 49 days of the MIL, the vehicle will no longer be allowed to start. This bulletin involves reprogramming the BPCM with the latest available software. NOTE: Additional module flashes are required for this update to be effective, the following modules
109820
SEAL - ROOF RAIL
109822
SEAL - ROOF RAIL
9100749
axle seal We have observed that some JL/JT rear axle shafts are leaking oil. Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.
109281
CENTER STACK – NONE
109223
BEZEL - INSTRUMENT PANEL
109224
DOOR - PASSENGER AIR BAG
18-107-25
Flash: Powertrain Control Module (PCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: ● P2450 - Fuel Tank Isolation Valve Stuck Open. ● P1D83 - Implausible Engine Oil Temperature Signal Received. Customers may experience one or more of the following: ● Fuel Door will not open due to intermittent Fuel Tank Isolation Valve (FTIV) Stuck Open. ● Reduced fuel efficiency.** ● Excessive oil life degradation shown when viewing fuel and oil data screen. **In addition, the following software enhancement is available: ● Hood Switch changes.** This bulletin involves reprogramming the PCM with the latest available software
08-394-25 REV. A
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure.
S2523000096
CEL (Check Engine Lamp)/ Brake lamp Illuminated. Diagnostic Trouble Code (DTC) P083F- Clutch Pedal Position Sensor Performance.
9100734
If the DTC B1E21-96: Backup Battery-Component Internal Failure is active and customer states Popup message will show at the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
08-394-25
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present echnicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure
S1819000004 REV.R
Shimmy Felt In Front End
108544
SWITCH - POWER WINDOW
108655
D-25-15 Rev. A Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
108657
ID-25-11 Rev. A Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
108463
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108464
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108458
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
108461
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
9100723
1.Identify Customer Concern Check for small traces of coolant near the water pump, especially around the weeper chamber. Confirm if coolant is visibly dripping from the weeper chamber. 2.Root Cause identification The weeper chamber is designed to collect small amounts of coolant (< 3 ml/h) that pass through the dynamic seal. Red traces or shadows around the chamber may appear during initial operation due to seal adaptation or vapor condensation. These traces are not necessarily signs of a leak. Continuous dripping of coolant, however, indicates a malfunction. 3.Service Repair Procedure Lift the vehicle using an elevator. Verify if coolant is actively dripping from the weeper chamber. Run the engine at idle, alternating speed between 2000 4000 rpm for 15 minutes. Observe the weeper chamber during this test: If coolant continues to drip: Replace the water pump (possible permanent damage to the dynamic seal). If dripping stops: No further action is needed; the vehicle can be returned to the customer. 4.Clarify Leak Sources Do not confuse leaks from: The Press-In-Place rubber gasket (between water pump and engine block), or The inlet pipe nipples with leaks from the weeper chamber.
S2508000100
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S1805000006 REV.B
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
9100684
When servicing/replacing 68415437A$ Transmission, take care to not damage the PIM to P2 harness. Also, when reinstalling the harness, route the harness properly and secure it at all the retention points.
105646
MODULE - STEERING CONTROL & COLUMN
9100325 Rev 1
Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.
08-116-25 REV. C
Service Hybrid Electric Vehicle System Warning Message Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B273C-00 - Digital Crash Input. NOTE: Technicians may find the DTC is stored or pending in the Hybrid Control Processor (HCP). Customers may experience one or more of the following: ● The "Service Hybrid Electric Vehicle System Warning” message and Light are displayed in the Instrument Panel Cluster (IPC) Fig. 1. NOTE: This message may be displayed for a few seconds and then disappear. ● The vehicle may no longer enter Electric or Hybrid drive modes.
23-034-25
Not applicable to vehicles built for US market. Parking Brake Will Not Release Customers may comment on the following: ● Park brake will not release. This bulletin involves using glue to repair the park brake handle positioning.
S2218000003 REV.B
Customer complaint may include a Mil On/Check Engine Lamp On and Electronic Throttle Control (ETC) Lamp On. There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:
S2408000031 REV.A
Vehicle is Not Charging When Connected to a Level One or Two Charger or a Public Charging Station
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
08-116-25 REV. B
Service Hybrid Electric Vehicle System Warning Message Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B273C-00 - Digital Crash Input. NOTE: Technicians may find the DTC is stored or pending in the Hybrid Control Processor (HCP). Customers may experience one or more of the following: ● The "Service Hybrid Electric Vehicle System Warning” message and Light are displayed in the Instrument Panel Cluster (IPC) Fig. 1. NOTE: This message may be displayed for a few seconds and then disappear. ● The vehicle may no longer enter Electric or Hybrid drive modes This bulletin involves installing a ferrite bead to the high voltage battery body harness.
21-038-25
Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode This bulletin involves replacing the transmission oil pump.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
08-231-25
Flash: Radio Frequency Hub Module (RFHM) Updates Customers must experience the following: ● Customers may be concerned about vehicle theft due to ability of key FOBs to be programmed through RFHM. Software enhancement includes: ● Update to the RFHM software to prevent unauthorized keyfob programming. ● This is intended to deter an unwanted drive off of the vehicle without the customer's knowledge. This bulletin involves updating the RFHM module with the latest available software.
106348
DAMPER - STEERING
106349
DAMPER - STEERING
23-006-25 REV. B
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield.
S2422000001 REV.D
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
09-018-25
Engine Cylinder Block Porosity Inspection - Engine Cold Start Rough Idle Customers may experience the following: ● Rough engine idle when cold starting the engine. ● Low coolant level in coolant recovery bottle.
105648
MODULE - ENGINE CONTROLLER
9100627
To inform dealers about the 850RE valve body PN: R8348504A connector: the original 16-pin connector included six pins that were not used in this application. To simplify the design, the connector has been optimized and updated to a 10-pin configuration.
9100624
Verify Reman part number availability. Order the "R" part number for all orders:
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100622
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
OTHERDOC_133
Global Telematics Box Module Over The Air Update from 5.39.1 to 5.65 TBM2.0 Software Version (FOTA) Customers may experience one or more of the following: - Error display of "Uconnect Box Requires Service/Wifi Unavailable" popups; [ TBM DTC B22A9-96 Internal Performance Failure ]. - Error display of "Uconnect Box Requires Service" pop-ups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ].
9100605
Shim - felt GIM # NUSENGCHR24018991: JL JT sun visor center support BSR. Add felt shim 68736674AA - 43MM OD x 10mm ID x 1mm thick.
14-012-25
Unable To Refuel Vehicle Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P2450 - Fuel Tank Isolation Valve Stuck Open. Customers may also comment on one or more of the following: ● Unable to open the fuel door. ● Difficult to refuel vehicle. This bulletin involves replacing the fuel vapor valve.
9100599
Underhood start/stop safety The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.
S2408000024REVA
Power Top Switch Unresponsive, Full Retractable Sky Roof Does Not Open or Close Customer Complaint/Technician Observation: The owner complains the top system is inoperative and that by pressing the switches the Power Top does not make any movement. Technician may or may not have Diagnostic Trouble Codes (DTCs). Repair Procedure: Perform the power top calibration prior to any switch or parts replacement.
08-116-25 REV. A
Service Hybrid Electric Vehicle System Warning Message Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B273C-00 - Digital Crash Input. NOTE: Technicians may find the DTC is stored or pending in the Hybrid Control Processor (HCP). Customers may experience one or more of the following: ● The "Service Hybrid Electric Vehicle System Warning” message and Light are displayed in the Instrument Panel Cluster (IPC) Fig. 1. NOTE: This message may be displayed for a few seconds and then disappear. ● The vehicle may no longer enter Electric or Hybrid drive modes. This bulletin involves installing a ferrite bead to the high voltage battery body harness.
9004003
Backlite Heated Liftgate Glass Assembly: For rear window defrost inoperative concerns where heated glass electrical tab has become detached, it is not necessary to replace the glass assembly. For loose or detached electrical tab, refer to TSB 23-007-25 for repair procedures on reattaching a loose tab. For burned or discolored gridlines on hard tops, DO NOT change the complete Flipper glass assembly. This discoloration is oxidation of the ceramic silver material and is normal. The Engineering standard call out the fact that this bus bar will change in color and is not a deterioration of the material or performance.
S2508000039
Universal Garage Door Opener (UGDO) Inoperative, LED Indicator Lamps Not Illuminating
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
S258A000013
AM Radio Static, With No Active or Stored Radio Antenna Diagnostic Trouble Codes (DTC).
9100547
Telematics Box Module Verify Z part number availability. Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only.
08-082-25 REV. A
High Voltage Wiring Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B273C-00 - Digital Crash Input. ● U0287-00 - Lost Communication With Transmission Fluid Pump Module 1. Customers may also experience one or more of the following: ● Vehicle shakes during a cold start. ● Noise is heard from the underbody near the P2 motor. This bulletin involves repairing the High Voltage (HV) cable harness to the Power Inverter Module (PIM)
08-116-25
Service Hybrid Electric Vehicle System Warning Message Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B273C-00 - Digital Crash Input. NOTE: Technicians may find the DTC is stored or pending in the Hybrid Control Processor (HCP). Customers may experience one or more of the following: ● The "Service Hybrid Electric Vehicle System Warning” message and Light are displayed in the Instrument Panel Cluster (IPC) Fig. 1. NOTE: This message may be displayed for a few seconds and then disappear. ● The vehicle may no longer enter Electric or Hybrid drive modes This bulletin involves installing a ferrite bead to the high voltage battery body harness.
104558
FCA Caribbean Warranty Newsletter – Volume 11, Issue 4
104557
Warranty Newsletter – Volume 11, Issue 4
08-082-25
High Voltage Wiring Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B273C-00 - Digital Crash Input. ● U0287-00 - Lost Communication With Transmission Fluid Pump Module 1. Customers may also experience one or more of the following: ● Vehicle shakes during a cold start. ● Noise is heard from the underbody near the P2 motor. REPAIR SUMMARY: This bulletin involves repairing the High Voltage (HV) cable harness to the Power Inverter Module (PIM)
08-061-25
Flash: Power Inverter Module(PIM) Flash Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician must find one or more of the following Diagnostic Trouble Code (DTC) has been set: ● P0C19-00 - Drive Motor A Torque Delivered Performance. ● P1B03-00 - Resolver Signal / MCPA Rationality. Customers may experience the following: ● Electric Vehicle (EV) system shuts down while transferring over to Internal Combustion Engine (ICE) motive power. Engine Stop Start (ESS) function will also not operate as a result of this condition This bulletin involves reprogramming the Auxiliary Hybrid Control Processor (AHCP) also known as PIM, with the latest available software.
9100749 Rev 1
We have observed that some JL/JT rear axle shafts are leaking oil. Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.
21-005-25
Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters. This bulletin involves reprogramming the TCM with the latest available software.
08-104-24 REV. A
Flash: Battery Pack Control Module (BPCM) Enhancements Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● **P0DAB - Hybrid/EV Cell Balancing Performance.** ● P0AA4 - Hybrid/EV Battery Negative Contactor 'A' Circuit Stuck Closed. ● P0AA1 - Hybrid Battery Positive Contactor Circuit Stuck Closed. ● P0CA6 - Hybrid/EV Battery Charging Current High. ● P0B24 - Unstable Hybrid Battery ‘A’ Voltage. ● P1C5E - Battery State or Health Failed. ● P0BBE - No Start - Loss or Reduction of Propulsion. ● P0607-00 - ECU Internal Performance. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. This bulletin involves reprogramming the BPCM with the latest software available. NOTE: Additional module flashes are required for this update to be effective, the following modules are all to be updated along with this BPCM update. ● Powertrain Control Module (PCM). ● Transmission Control Module (TCM). ● Integrated Dual Charging Control Module (IDCM). ● Hybrid Control Processor (HCP), Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM)
21-025-24 REV. A
Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. **The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters.** **This bulletin involves reprogramming the TCM with the latest available software.** NOTE: **Please be sure that the 04B recall is completed prior to performing this TSB. This TCM software update is covered by the 04B recall if still incomplete.**
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.