Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
107418
SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH
9100645
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
9100653
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
103954
ACTUATOR - A/C AND HEATER
104087
ACTUATOR - A/C AND HEATER
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
101232
Plate - Planetary
100192
BOW - FOLDING TOP
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1723000037 REV.A
Freedom Panel Underside Rough And Or White Coating Flaking
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S2208000138RevA
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
9004473
complete wiring harness Before replacing this harness, please check for an available connector repair kit at the following: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
V51
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
9004378
KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
71838
Warranty Bulletin D-18-16 Rev. B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)
S2008000108
Rear Wiper Will Not Turn On After Recent Hard Top Removal
S1721000016
Service 4wd Light On, Message AWD System Service Required
S2025000005
Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
S1508000480
Speed Control Operates Intermittently
D-20-02 Rev. A
DIPAP Requirements - Addition of Jeep Wrangler (JL/JK) and Jeep Gladiator (JT) Hard Top and Targa Top Panel Replacements - All Dealers (Rev. A)
D-20-02
DIPAP Requirements - Addition of Jeep Wrangler (JL/JK) and Jeep Gladiator (JT) Hard Top and Targa Top Panel Replacements - All Dealers
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
9004142
DOOR, Assembly (Front or Rear) For concern of flag nut not aligned to hole, use a blunt tool and lightly tap on the flag nut to knock it loose from e-coat that has dried it in place.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
DOT-L4X8T-04
The SKU is a Tie Rod Center Stud. The Customer commnunication requested return of unsold inventory to inpsect for possible incorrect direction threads (right hand rather than left hand). Incorrect direction threads will prevent it from being installed.
S80
Customer Satisfaction Notification S80 Aftermarket Dana 60 Front Axle The aftermarket front axle steering knuckles have been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.
9003355
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003699
Heated Seat Elements; Cushion and Back DEALERCONNECT HEATED ELEMENT RESISTANCE INFO OUT IS OF SPEC. Prior to ordering any of the parts (55057300A$, 55057293A$, 55057301A$, 55057294A$) Please contact Micah Straub at cell phone# 248-613-2478 for further instructions. Leave a voice mail and your call will be returned promptly. 5.1 to 7.8 is the correct resistance value although ambient temperature will affect this value. Please call for detailed information. If no return call in 15 minutes, proceed with repair.
08-005-17 REV. A
Clockspring Replacement (X68 Warranty Extension) This bulletin involves diagnosing the clockspring/Steering Angle Sensor (SAS).If the diagnostic tests indicate the clockspring/SAS requires replacement, replace the clockspring, upper and lower steering column shrouds and steering wheel back cover. Some customers may experience the illumination of the airbag warning lamp or traction control indicator lamp. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: B1B00 - Driver Airbag Squib 1 Circuit Low. B1B01 - Driver Airbag Squib 1 Circuit High. B1B02 - Driver Airbag Squib 1 Circuit Open. B1B03 - Driver Airbag Squib 1 Circuit Shorted Together. B1B04 - Driver Airbag Squib 2 Circuit Low. B1B05 - Driver Airbag Squib 2 Circuit High. B1B06 - Driver Airbag Squib 2 Circuit Open. B1B07 - Driver Airbag Squib 2 Circuit Shorted Together. C123F - Steering Angle Sensor Comparative Performance. C1219 - Steering Angle Sensor Erratic Performance. C2205 - Steering Angle Sensor Internal. P0579 - Speed Control Multiplexed Switch #1 Performance. P0581 - Speed Control Multiplexed Switch #1 High. P0591 - Speed Control Multiplexed Switch #2 Performance. P0593 - Speed Control Multiplexed Switch #2 High. U1109 - Lost Communication With Lin Steering Wheel Controls.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
68141352A$
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.
23-037-16
Out Of Tolerance Door And Windshield Frame Gaps Causing Water Leaks This bulletin involves adjusting the windshield frame and A-pillar between the door to close gaps and prevent water leaks. The customer may describe gaps between the windshield frame, door and top of cowl. There may also be a water leak.
68105583A$
PENTASTAR OIL FILTER ADAPTER BEFORE REPLACING THIS PART, PLEASE CALL ANY ONE OF THE FOLLOWING PEOPLE. ENGINEERING IS SEEKING INFORMATION REGARDING THIS PART.~ DYE MUST BE USED TO DETERMINE WHERE THE LEAK IS COMING FROM BEFORE REPLACING. ALSO PLEASE CHECK THE RECENTLY UPDATED SERVICE BULLETIN NUMBER 09-008-15. ~ FIRST: NICK MORAND CELL (248) 410-5078 - NICK.MORAND@FCAGROUP.COM SECOND: BOB JACKSON CELL (248) 944-0466 - BOB.JACKSON@FCAGROUP.COM THIRD: JOE LOVELL CELL (734 309-6467 - JOE.LOVELL@FCAGROUP.COM IF A RESPONSE IS NOT RECEIVED WITHIN 15 MINS, THEN PROCEED WITH THE NECESSARY REPAIR.
68105583A
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
68141352A
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
02-001-16
Vibration/Shimmy At Low Speed With 4 Inch Mopar Lift Kit Installed This bulletin involves replacing the front track bar bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.
0200116
Vibration/Shimmy At Low Speed With 4 Inch Mopar Lift Kit Installed.
1PH98RXFA$
PANEL, Targa Top, Complete with Hardware For water sloshing noise in the Targa Top Panel, do not replace the panel. There is a drain hole along the rear edge of the panel (in car position). After draining the panels, inform the customer of the drain hole and if the issue returns they can drain the panels themselves. Storage of panels outdoors in certain positions will cause water infiltration.~ ~ For a water leak from the center front edge of the Targa Top Panels, do not replace the panels, replace the SEAL, Targa Top (Part Number 68088055AA).
Panel
Parts.
68143886A$
RADIATOR, Engine Cooling Before replacing the radiator, please call Andy Wilkinson at cell (248) 613 6301 or email at Andrew.Wilkinson@fcagroup.com. If no answer and if you do not receive a return call within 15 minutes please continue with the normal repair.~
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
02-008-15
Vibration/Shimmy At Low Speed With 4 Inch Mopar Lift Kit Installed This bulletin involves replacing the front track bar bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.
18-053-15 REV A
Malfunction Indicator Lamp (MIL) Illumination P0344 - Camshaft Position Sensor Intermittent This bulletin involves inspection and repair of the engine wire harness and replacing the harness retainer tower clip. A small number of customers may experience a MIL illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1 set in the Powertrain Control Module (PCM) memory.
08-115-15
Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.
18-077-15
Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) set in the PCM memory: ? U0140 - Lost Communication With Body Control Module. Customers may also describe one or more of the following conditions: ? Less than desired shift points during Wide Open Throttle (WOT) operation. ? Perceived misfire under normal acceleration. Software update is also available for customers with vehicles equipped with Manual Transmissions (DEH) to disable the starter protection feature for Rock Crawling.
23-038-15
Cracked Vinyl Soft Top Window This bulletin provides soft top vinyl window precautions during cold weather.
08-089-15
Security System Nuisance Alarms This bulletin involves replacing the five alarm sensor transmitters. The customer may describe the security system nuisance alarms with no apparent cause for activation.
06-001-15
Squeak Noise While Depressing The Clutch Pedal This bulletin involves lubricating the clutch pedal return spring. Squeak noise from under the dash while depressing or releasing the clutch pedal.
09-008-15
3.6L Oil Loss Diagnostic Aid This bulletin involves additional information on oil loss.
SB-09-008-15
VARIOUS VEHICLES ARE EXPERIENCING LOSS OF OIL, AND POSSIBLY AN OIL LEAKAGE POOLING IN ENGINE VALLEY AND POSSIBLY NEED REPLACING OIL FILTER HOUSING. MODEL 2014. *PE
18-053-15
CHRYSLER 2012-2015 JEEP WRANGLER (RHD): BULLETIN INFORMATION INVOLVES REPAIRS AND INSPECTION OF THE ENGINE HARNESS AND REPLACING THE HARNESS RETAINER TOWER CLIP. *LJ
21-026-15
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience one or more of the following transmission related concerns. ? Less than desired shift response when towing or driving up steep hills in high ambient temperatures. ? Delayed shift when driving in 4WD Low. ? Vibration or resonance in the cabin on acceleration from a cruising speed.
08-038-15
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.
23-011-15
Tailgate Retaining Strap Over Extends And Breaks This bulletin involves painting and replacing both tailgate hinges and replacing the tailgate retaining strap. If damaged, it may also be necessary to replace the tailgate hinge covers and/or right side tail lamp as required. The tailgate retaining strap is damaged due to the tailgate hinge over extending. The retaining strap typically breaks at the body side of the retaining strap attachment. Tailgate hinge covers and/or tail lamp may also be damaged as a result of over extension.
08-022-15
Service Tire Pressure System Message This bulletin involves performing a wiTECH Misc-function routine. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): ? C151D - Tire Pressure Sensor Location Undetermined. ? C1581 - Front/Rear Side Tire Pressure Sensor Location Undetermined.
9003225
Part Description: Soft Top Quarter Window or Rear Window Issue Description: Please cycle the zipper 5-10 times when there is a single skipped zipper tooth.
08-112-14
Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.
0811214
Hands Free Feature Inoperative
23-034-14 REV. A
Cowl Trim Panel Fastener Water Leak This bulletin involves modifying or replacing the cowl trim panel fasteners to correct a water leak condition. The customer may describe a water accumulation condition on the vehicle floor front foot well area.
23-034-14REV.A
JEEP WRANGLER 2012-2014: COWL TRIM PANEL FASTENER WATER LEAK. CUSTOMER MAY EXPERIENCE WATER ACCUMULATION ON THE FRONT FLOOR AREA. *LJ UPDATED 05/01/15. *LJ
2303414REVA
Cowl Trim Panel Fastener Water Leak This bulletin involves modifying or replacing the cowl trim panel fasteners to correct a water leak condition. The customer may describe a water accumulation condition on the vehicle floor front foot well area.
2303414
Cowl Trim Panel Fastener Water Leak
18-051-14 REV. A
Flash: J8 Mining Vehicle Speed Limiting This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of J8 Vehicles built as over-the-road units for non-reg BUX markets and sold to US-based mining operations with the intent of re-programming the diesel PCM to limit vehicle-speed in the mining environment. The discretion of which mining flash is to be used is left to the discretion of the operator.
18-051-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
1805114
Flash: J8 Mining Vehicle Speed Limiting This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of J8 Vehicles built as over-the-road units for non-reg BUX markets and sold to US-based mining operations with the intent of re-programming the diesel PCM to limit vehicle-speed in the mining environment. The discretion of which mining flash is to be used is left to the discretion of the operator.
1805114REVA
Flash: J8 Mining Vehicle Speed Limiting This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of J8 Vehicles built as over-the-road units for non-reg BUX markets and sold to US-based mining operations with the intent of re-programming the diesel PCM to limit vehicle-speed in the mining environment. The discretion of which mining flash is to be used is left to the discretion of the operator.
18-071-14
Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience less than desired shift points during Wide Open Throttle (WOT) operation. This PCM software has been enhanced to provide optimal shift points during these operating conditions.
1807114
Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience less than desired shift points during Wide Open Throttle (WOT) operation. This PCM software has been enhanced to provide optimal shift points during these operating conditions.
23-034-14
Cowl Trim Panel Fastener Water Leak This bulletin involves modifying or replacing the cowl trim panel fasteners to correct a water leak condition. The customer may describe a water accumulation condition on the vehicle floor front foot well area.
08-086-14 REV. A
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.
0808614a
RBZ Or RHB Radio Software Enhancements
23-022-14 REV. A
Tailgate Retaining Strap Over Extends And Breaks This bulletin involves painting and replacing both tailgate hinges and replacing the tailgate retaining strap. If damaged, it may also be necessary to replace the tailgate hinge covers and/or right side tail lamp as required. The tailgate retaining strap is damaged due to the tailgate hinge over extending. The retaining strap typically breaks at the body side of the retaining strap attachment. Tailgate hinge covers and/or tail lamp may also be damaged as a result of over extension.
23-022-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2302214
Tailgate Retaining Strap Over Extends And Breaks
23-029-14
Front Passenger Seat High Effort To Adjust Fore/Aft This bulletin involves applying MOPAR grease to the contact points between the inner and outer seat tracks to reduce adjustment effort. High effort to adjust the front passenger seat in the fore/aft direction.
2302914
Front Passenger Seat High Effort To Adjust Fore/Aft
18-054-14
Intermittent Extended Crank, Long Crank Time. This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.
1805414
Intermittent Extended Crank, Long Crank Time.
24-010-14
Flash: HVAC System Improvements This bulletin involves updating the HVAC control module with new software. The customer may notice that the blower motor speed may slow down at times. This condition will only happen at mid to high ambient temperatures, 75F (24C) or higher. Also the A/C request may be locked on after a remote start. Only after the vehicle is turned off and restarted, will the customer be able to turn the A/C on or off.
08-086-14
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).
0808614
RBZ Or RHB Radio Software Enhancements
18-051-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-029-14 REV. A
Flash: MIL Illumination. Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: P2097- Downstream Fuel Trim System 1 Rich. P2099- Downstream Fuel Trim System 2 Rich. P0830- Clutch Pedal Switch ?A? Circuit. (Vehicles with manual transmission only) P1239- Engine Oil Temperature Too Low.The following powertrain system improvements/enhancements are also included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy.Updating the PCM software will correct the conditions listed above.
18-029-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
1802914
Flash: MIL Illumination. Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: P2097- Downstream Fuel Trim System 1 Rich. P2099- Downstream Fuel Trim System 2 Rich. P0830- Clutch Pedal Switch ?A? Circuit. (Vehicles with manual transmission only) P1239- Engine Oil Temperature Too Low.The following powertrain system improvements/enhancements are also included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy.Updating the PCM software will correct the conditions listed above.
9002503
RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect
23-022-14
Tailgate Retaining Strap Over Extends And Breaks This bulletin involves painting and replacing both tailgate hinges and replacing the tailgate retaining strap. If damaged, it may also be necessary to replace the tailgate hinge covers and/or right side tail lamp as required. The tailgate retaining strap is damaged due to the tailgate hinge over extending. The retaining strap typically breaks at the body side of the retaining strap attachment. Tailgate hinge covers and/or tail lamp may also be damaged as a result of over extension.
16-001-14
High Speed Vibration Coming From The Rear Of The Vehicle This bulletin involves replacing the rear propeller shaft. Customers may indicate that they feel a vibration coming from the rear of the vehicle at speeds between 80 kph (50 mph) and 120 kph (75 mph).
SB-16-001-14
DODGE: ON CERTAIN TRUCKS, WHEN AT SPEEDS BETWEEN 50 MPH (80 KPH) AND 75 MPH (120 KPH), FROM THE REAR OF TRUCK, VIBRATION CAN BE FELT. MODEL 2014 RAM 1500, RAM, WRANGLER. *PE
08-068-14
Flash: No Start, No Crank, B1A25 Invalid Key B1A29 Skim Basestation MIismatch This bulletin involves reprogramming the Wireless Control Module (WCM). The customer may experience a no crank, no start. Upon further diagnosis active DTCs may be found, B1A25 Invalid Key B1A29 Skim Basestation MIismatch.
21-023-14
Flash: Transmission Shift Enhancements This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Wrangler Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32°C/90°F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Rubicon Only.2.8L Wrangler Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) Transmission shifting while accelerating from a stop does not meet customers expectation. Poor vehicle performance in Drive Poor vehicle performance in Auto Stick Mode. Rubicon Only.
9003112
Soft Top Door Rail Service Kits Use this soft top door frame rail kit for worn foam or a water leak: 1) For 2010 - 2014 units, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply new foam part.~ 2) For 2007 - 2009 units, cut off 8.0 mm from the end that faces the windshield, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply modified foam part.
18-034-14 REV. A
P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
18-034-14
P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
SB-18-034-14
ON SOME MODEL VEHICLES AND JEEPS, (MY 2013-2014)MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATES AND DIAGNOSTIC TROUBLE CODE (DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE
08-024-14
RHW RHP Radio Software Enhancements This bulletin involves upgrading the software on the RHW or RHP Radio. The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.
0802414
RHW RHP Radio Software Enhancements
08-043-14
Cruise Control System Slow To Respond To Cruise Control Switch Inputs This bulletin involves upgrading the software in the Powertrain Control Module (PCM). A customer may experience, slow response to cruise control switch activations.
0804314
Cruise Control System Slow To Respond To Cruise Control Switch Inputs
11-002-14
Exhaust Rattle At Idle Speeds This bulletin involves replacing the catalytic converter with a new assembly and hanger system. The customer may experience a buzz, squeak or rattle (BSR) at idle speeds.
9003081
Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
18-029-14
Flash: MIL Illumination. Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P2097- Downstream Fuel Trim System 1 Rich ? P2099- Downstream Fuel Trim System 2 Rich The following powertrain system improvements/enhancements are also included in this software release: ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Updating the PCM software will correct the conditions listed above.
24-002-14
Driver And Passenger HVAC Blower Air Temperatures Are Not The Same When ?Sync? Setting Mode Is Selected And Headlamps Always Stay On. This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.
08-029-14
Flash: Erroneous Message Displayed In The Odometer Or Trip Odometer Display Area While In the Messaging Mode This Bulletin involves reconfiguring the vehicle for proper messaging display. The customer may experience an erroneous message in the odometer/trip odometer display area while in the message mode. The warning message will be displayed for the entire ignition key cycle.
07-001-14
Intermittent Engine Cooling Fan Operation This bulletin involves an inspection of the Engine Cooling Fan Module and replacement if necessary. The customer may experience an engine overheat condition or lack of cooling from the air conditioning system.
SB-07-001-14
JEEP: VEHICLE'S AIR CONDITIONING SYSTEM IS LACKING COOLING OR THE ENGINE IS OVERHEATING AND NEEDS TO BE INSPECTED AND REPLACED, IF NECESSARY. MODEL 2014 WRANGLER. *PE
18-003-14
Flash: Unable to Program Keys After Wireless Control Module Replacement and/or Malfunction Indicator Lamp (MIL) Illumination This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Technicians may find that the original vehicle keys/FOBIKs do not function properly following replacement of the Wireless Control Module(WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information.A small number of customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0606 - Internal Control ProcessorIf the WCM had been replaced prior to this software update, the original keys/FOBIKs will need to be replaced.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.