Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
107418
SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH
9100645
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
9100653
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
103954
ACTUATOR - A/C AND HEATER
104087
ACTUATOR - A/C AND HEATER
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
101232
Plate - Planetary
100192
BOW - FOLDING TOP
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1723000037 REV.A
Freedom Panel Underside Rough And Or White Coating Flaking
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
9004473
complete wiring harness Before replacing this harness, please check for an available connector repair kit at the following: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
9004378
KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
71838
Warranty Bulletin D-18-16 Rev. B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)
S1908000028 Rev.
(Rev. A) Power Inverter Load Ratings
S1908000102
(Rev. A) Power Inverter Load Ratings
S2008000108
Rear Wiper Will Not Turn On After Recent Hard Top Removal
S1721000016
Service 4wd Light On, Message AWD System Service Required
S2025000005
Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
S1508000480
Speed Control Operates Intermittently
D-20-02 Rev. A
DIPAP Requirements - Addition of Jeep Wrangler (JL/JK) and Jeep Gladiator (JT) Hard Top and Targa Top Panel Replacements - All Dealers (Rev. A)
D-20-02
DIPAP Requirements - Addition of Jeep Wrangler (JL/JK) and Jeep Gladiator (JT) Hard Top and Targa Top Panel Replacements - All Dealers
V51
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9004142
DOOR, Assembly (Front or Rear) For concern of flag nut not aligned to hole, use a blunt tool and lightly tap on the flag nut to knock it loose from e-coat that has dried it in place.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
DOT-L4X8T-04
The SKU is a Tie Rod Center Stud. The Customer commnunication requested return of unsold inventory to inpsect for possible incorrect direction threads (right hand rather than left hand). Incorrect direction threads will prevent it from being installed.
S80
Customer Satisfaction Notification S80 Aftermarket Dana 60 Front Axle The aftermarket front axle steering knuckles have been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.
9003511
Console Lid If you are replacing the console lid because it does not open properly or because the button covers are missing, check STAR Parts - there is a button cover replacement kit available. The part numbers for the buttons are as follows: Left - 68359329A$ Right - 68375214A$
T12
Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.
9003355
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
23-029-17
Dimpled Driver Side Front Leather Heated Seat This bulletin involves inspecting and installing heater element patches and replacing seat cushion cover, on the driver?s front seat. The customer may describe, the driver?s front leather seat has dimples in the seat bottom. The dimples are caused by openings in the heated seat element, seeFig. 1.Dimple Location On Leather Seats1 - Dimples
9003413
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
23-028-17
Squeaking Noise Below The Front Seat While Turning and Going Over Bumps This bulletin involves replacing the bolt and bushing on driver and passenger side seat slide mechanism to resolve a squeaking issue (Two door models only). The customer may describe a squeak heard under the front passenger or driver side seat, while turning or driving over bumps.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
9003699
Heated Seat Elements; Cushion and Back DEALERCONNECT HEATED ELEMENT RESISTANCE INFO OUT IS OF SPEC. Prior to ordering any of the parts (55057300A$, 55057293A$, 55057301A$, 55057294A$) Please contact Micah Straub at cell phone# 248-613-2478 for further instructions. Leave a voice mail and your call will be returned promptly. 5.1 to 7.8 is the correct resistance value although ambient temperature will affect this value. Please call for detailed information. If no return call in 15 minutes, proceed with repair.
08-005-17 REV. A
Clockspring Replacement (X68 Warranty Extension) This bulletin involves diagnosing the clockspring/Steering Angle Sensor (SAS).If the diagnostic tests indicate the clockspring/SAS requires replacement, replace the clockspring, upper and lower steering column shrouds and steering wheel back cover. Some customers may experience the illumination of the airbag warning lamp or traction control indicator lamp. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: B1B00 - Driver Airbag Squib 1 Circuit Low. B1B01 - Driver Airbag Squib 1 Circuit High. B1B02 - Driver Airbag Squib 1 Circuit Open. B1B03 - Driver Airbag Squib 1 Circuit Shorted Together. B1B04 - Driver Airbag Squib 2 Circuit Low. B1B05 - Driver Airbag Squib 2 Circuit High. B1B06 - Driver Airbag Squib 2 Circuit Open. B1B07 - Driver Airbag Squib 2 Circuit Shorted Together. C123F - Steering Angle Sensor Comparative Performance. C1219 - Steering Angle Sensor Erratic Performance. C2205 - Steering Angle Sensor Internal. P0579 - Speed Control Multiplexed Switch #1 Performance. P0581 - Speed Control Multiplexed Switch #1 High. P0591 - Speed Control Multiplexed Switch #2 Performance. P0593 - Speed Control Multiplexed Switch #2 High. U1109 - Lost Communication With Lin Steering Wheel Controls.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9002718
Hands Free Module - Convergence Telematics Module (CTM) Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
9003231
RHB/RBZ Radio For JK, MK, and RT ONLY: RHB/RBZ radio that supports Bluetooth and Hands- Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE
25-003-16 REV. A
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
2500316
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
10-001-16 REV. A
Non-desiccated Passenger Frontal Airbag This bulletin involves providing to purchasers of affected un-sold vehicles, prior to purchase, the attached "Important Notice" document and retain a signed copy. No customer symptoms or conditions are associated with this RRT. If a customer?s VIN is listed in VIP or your RRT VIN list, RRT applies only to those unsold Vins listed.
10-002-16
Non-desiccated Passenger Frontal Airbag This bulletin involves providing to purchasers of affected un-sold vehicles, prior to purchase, the attached "Important Notice" document and retain a signed copy. No customer symptoms or conditions are associated with this RRT. If a customer?s VIN is listed in VIP or your RRT VIN list, RRT applies only to those unsold Vins listed.
05091960A
Hands Free Module - CTM ? Peiker Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
05091960A$
Hands Free Module - CTM ? Peiker Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
10-001-16
Non-desiccated Passenger Frontal Airbag This bulletin involves providing to purchasers of affected un-sold vehicles, prior to purchase, the attached "Important Notice" document and retain a signed copy. No customer symptoms or conditions are associated with this RRT. If a customers VIN is listed in VIP or your RRT VIN list, RRT applies only to those unsold Vins listed.
68089579A$
Console Lid JK ONLY - If you are replacing the console lid because it does not open properly or because it does not close properly, please also replace the console base and the lock cylinder (04746315) in addition to the console lid. If you have any questions, please call Mike Wicker on cell (248) 821-9350 prior to replacing the component. If you dont receive a response within 15 minutes, please continue with normal repair procedure.
68141352A$
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.
23-037-16
Out Of Tolerance Door And Windshield Frame Gaps Causing Water Leaks This bulletin involves adjusting the windshield frame and A-pillar between the door to close gaps and prevent water leaks. The customer may describe gaps between the windshield frame, door and top of cowl. There may also be a water leak.
05091326A$
RHB/RBZ Radio For JK, MK, and RT ONLY: RHB/RBZ radio that supports Bluetooth and Hands- Free. For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
18-041-16 REV. A
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following Diagnostic Trouble Codes (DTCs) have been set: · **P0300 - Multiple Cylinder Misfire (3.6L Engine Sales Code ERB only). · P0306 - Cylinder 6 Misfire (Automatic Transmissions only).** · P0335 - Crankshaft Position Sensor Circuit. · P0456 - EVAP System Small Leak (3.6L Engine Sales Code ERB only). · U0140 - Lost Communication With Body Control Module.
68018109A$
Actuator- A/C Heater Before replacing this actuator call Matt Sasina at cell (248) 464-4982. If no response in 15 minutes, continue with repair.
68067457A
Anti-Lock Brake Module (ABS) 2015 and 2016 JK ONLY; Before replacing the ABS module, please call Breanne Scherbaty at cell (586) 604-4582. If you don't receive response within 15 minutes, please continue with normal repair procedure.
68067457A$
Anti-Lock Brake Module (ABS) 2015 and 2016 JK ONLY; Before replacing the ABS module, please call Breanne Scherbaty at cell (586) 604-4582. If you don't receive response within 15 minutes, please continue with normal repair procedure.
5ME18DX9A
Console Lid JK ONLY - If you are replacing the console lid because it does not open properly or because it does not close properly, please also replace the console base and the lock cylinder (04746315) in addition to the console lid. If you have any questions, please call Mike Wicker on cell (248) 821-9350 prior to replacing the component. If you don?t receive a response within 15 minutes, please continue with normal repair procedure.
5ME18DX9A$
Console Lid JK ONLY - If you are replacing the console lid because it does not open properly or because it does not close properly, please also replace the console base and the lock cylinder (04746315) in addition to the console lid. If you have any questions, please call Mike Wicker on cell (248) 821-9350 prior to replacing the component. If you don?t receive a response within 15 minutes, please continue with normal repair procedure.
68105583A$
PENTASTAR OIL FILTER ADAPTER BEFORE REPLACING THIS PART, PLEASE CALL ANY ONE OF THE FOLLOWING PEOPLE. ENGINEERING IS SEEKING INFORMATION REGARDING THIS PART.~ DYE MUST BE USED TO DETERMINE WHERE THE LEAK IS COMING FROM BEFORE REPLACING. ALSO PLEASE CHECK THE RECENTLY UPDATED SERVICE BULLETIN NUMBER 09-008-15. ~ FIRST: NICK MORAND CELL (248) 410-5078 - NICK.MORAND@FCAGROUP.COM SECOND: BOB JACKSON CELL (248) 944-0466 - BOB.JACKSON@FCAGROUP.COM THIRD: JOE LOVELL CELL (734 309-6467 - JOE.LOVELL@FCAGROUP.COM IF A RESPONSE IS NOT RECEIVED WITHIN 15 MINS, THEN PROCEED WITH THE NECESSARY REPAIR.
68241067A
TPM Sensor or Control Module 2015 and 2016 JK vehicles only - Engineering is investigating a Tire Pressure Monitor (TPM) issue for TPM lamp ON.~ Prior to replacing any components (Sensor or TPM Control Module) on MY15 or 16 JK vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.
68241067A$
TPM Sensor or Control Module 2015 and 2016 JK vehicles only - Engineering is investigating a Tire Pressure Monitor (TPM) issue for TPM lamp ON.~ Prior to replacing any components (Sensor or TPM Control Module) on MY15 or 16 JK vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.
23-025-16
Discolored Door Hinge Nuts This bulletin involves replacing all the lower nuts on the side upper and lower door hinges. The customer may describe discoloring or rust from the lower nut securing the doors to the hinges.
2302516
Discolored Door Hinge Nuts This bulletin involves replacing all the lower nuts on the side upper and lower door hinges. The customer may describe discoloring or rust from the lower nut securing the doors to the hinges.
68105583A
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
RL305553A
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
68141352A
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
18-041-16
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following Diagnostic Trouble Codes (DTCs) have been set: · **P0335 - Crankshaft Position Sensor Circuit. · P0306 - Cylinder 6 Misfire (Automatic Transmissions only). · P0456 - EVAP System Small Leak (3.6L Engine Sales Code ERB only).** · U0140 - Lost Communication With Body Control Module.
1804116
Diagnostic And System Improvements.
02-001-16
Vibration/Shimmy At Low Speed With 4 Inch Mopar Lift Kit Installed This bulletin involves replacing the front track bar bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.
0200116
Vibration/Shimmy At Low Speed With 4 Inch Mopar Lift Kit Installed.
05149171A$
Oxygen Sensor Before replacing the Upstream (1/1) O2 Sensor on a 2.4L MK due to a P0131 fault code, please contact Vijay Thiruvenkatachary at cell (906) 281-8495.~ Before replacing the Left Downstream (2/2) O2 Sensor on a 3.6L JK due to a P0157 fault code, please call Jerry Tomlin at cell (248) 202-5329. ~ Engineering would like determine whether the sensor has been contaminated with oil.~ If no response is received within 15 minutes, then continue with repair. For all other fault codes, please perform the applicable diagnostic routine.
05149180A$
Oxygen sensor Before replacing the Right Downstream (1/2) O2 Sensor for a P0137 code on a 3.6L JK, please contact Jerry Tomlin at cell (248) 202-5329. If no response within 15 minutes, continue with repair.~ Engineering is investigating whether the sensors are getting contaminated with oil. For any other P-Code besides P0137, follow the applicable diagnostic procedure.
1PH98RXFA$
PANEL, Targa Top, Complete with Hardware For water sloshing noise in the Targa Top Panel, do not replace the panel. There is a drain hole along the rear edge of the panel (in car position). After draining the panels, inform the customer of the drain hole and if the issue returns they can drain the panels themselves. Storage of panels outdoors in certain positions will cause water infiltration.~ ~ For a water leak from the center front edge of the Targa Top Panels, do not replace the panels, replace the SEAL, Targa Top (Part Number 68088055AA).
Panel
Parts.
52125003A$
Wheel Speed Sensors For Jeep Wrangler (JK) only. Before replacing the wheel speed sensors, please check for wiring/connection to the speed sensor. If the sensor is replaced, record the fault codes and note any damage to the sensor.~
0801416
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
68143886A$
RADIATOR, Engine Cooling Before replacing the radiator, please call Andy Wilkinson at cell (248) 613 6301 or email at Andrew.Wilkinson@fcagroup.com. If no answer and if you do not receive a return call within 15 minutes please continue with the normal repair.~
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
02-008-15
Vibration/Shimmy At Low Speed With 4 Inch Mopar Lift Kit Installed This bulletin involves replacing the front track bar bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.
53034160A
Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
18-053-15 REV A
Malfunction Indicator Lamp (MIL) Illumination P0344 - Camshaft Position Sensor Intermittent This bulletin involves inspection and repair of the engine wire harness and replacing the harness retainer tower clip. A small number of customers may experience a MIL illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1 set in the Powertrain Control Module (PCM) memory.
05184349A
Before replacing this part for debris issue faults, please call the following people;~ Engineering is seeking information regarding this part.~ Bob Smith ? Cell (248) 202-9458 - Robert.M.Smith@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
08-115-15
Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.
52060156A
Part Description: Wheel Speed Sensors Issue Description: Before replacing the front wheel speed sensors, please call Gurdial Dhami at cell (226) 346-7919. If you do not receive a return call after 15 minutes, please proceed with repair.
23-038-15
Cracked Vinyl Soft Top Window This bulletin provides soft top vinyl window precautions during cold weather.
56046094A
Part Description: Cruise Control Switch Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair
56046094A$
Part Description: Cruise Control Switch Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair
RL156209A
Part Description: Transmission Issue Description: If the vehicle you are repairing exhibits a whine/whistle noise when traveling at low speeds or when shifting into gear please call Jian Zhu on his cell at (248) 379-1132 prior to replacing the transmission. Jian is looking to get information. Also, Engineering would like to visit a dealers located in the SE Michigan area with a vehicle exhibiting the above complaint. If Jian cannot be reached within 15 minutes proceed with the repair.
RL156209A$
Part Description: Transmission Issue Description: If the vehicle you are repairing exhibits a whine/whistle noise when traveling at low speeds or when shifting into gear please call Jian Zhu on his cell at (248) 379-1132 prior to replacing the transmission. Jian is looking to get information. Also, Engineering would like to visit a dealers located in the SE Michigan area with a vehicle exhibiting the above complaint. If Jian cannot be reached within 15 minutes proceed with the repair.
08-089-15
Security System Nuisance Alarms This bulletin involves replacing the five alarm sensor transmitters. The customer may describe the security system nuisance alarms with no apparent cause for activation.
06-001-15
Squeak Noise While Depressing The Clutch Pedal This bulletin involves lubricating the clutch pedal return spring. Squeak noise from under the dash while depressing or releasing the clutch pedal.
08-068-15
Flash: Poor Audio Sound Quality This bulletin involves upgrading the software in the Amplifier (AMP). The customer may experience poor audio sound quality.
18-053-15
CHRYSLER 2012-2015 JEEP WRANGLER (RHD): BULLETIN INFORMATION INVOLVES REPAIRS AND INSPECTION OF THE ENGINE HARNESS AND REPLACING THE HARNESS RETAINER TOWER CLIP. *LJ
23-019-15
Discolored Door Hinge Nuts This bulletin involves replacing all the lower nuts on the side upper and lower door hinges. The customer may describe discoloring or rust from the lower nut securing the doors to the hinges.
2301915
Issue
21-026-15
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience one or more of the following transmission related concerns. ? Less than desired shift response when towing or driving up steep hills in high ambient temperatures. ? Delayed shift when driving in 4WD Low. ? Vibration or resonance in the cabin on acceleration from a cruising speed.
18-029-15
Flash: Engine Oil Temp Too Low After Extended Idle This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or the following symptoms. Upon further investigation the technician may find the Diagnostic Trouble Code (DTC) listed below: ? P1239 Engine Oil Temperature Too Low. ? Perceived misfire under normal acceleration. ? Starter protection feature will be disabled.
18-024-15
Flash: U0140 Lost Communication With Body Control Module This bulletin involves reprogramming the Powertrain Control Module (PCM) with update software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.
9003225
Part Description: Soft Top Quarter Window or Rear Window Issue Description: Please cycle the zipper 5-10 times when there is a single skipped zipper tooth.
MDH101506
THIS TSB CONTAINS AN OWNER NOTIFICATION LETTER. SEE DOCUMENT SEARCH BUTTON BELOW. FIAT CHRYSLER 2015 JEEP WRANGLER: RECALL APPLIES TO 3.6L ENGINE BUILT THROUGH OCTOBER 15, 2014. PCM MAY NOT DETECT A FAILED OXYGEN SENSOR. POSSIBLY IN AN INCREASE IN TAILPIPE EMISSIONS WHICH COULD EXCEED FEDERAL/CALIFORNIA EMISSIONS STANDARDS. *LJ
23-015-15
Water leak- Split header seal at end mold.
2301515
Water leak- Split header seal at end mold.
08-014-15
RES RBZ RHB RHR Poor Audio Quality This bulletin involves replacing the radio, if required. A customer may experience poor audio quality and vehicles with RHB radios may have poor navigation language.
0801415
RES RBZ RHB RHR Poor Audio Quality This bulletin involves replacing the radio, if required. A customer may experience poor audio quality and vehicles with RHB radios may have poor navigation language.
23-004-15
Side Steps Are Missing This bulletin involves inspecting for and if necessary installing the Side Steps. Side Steps are missing. Inspect for and if necessary install the Side Steps.
2300415
Side Steps Are Missing This bulletin involves inspecting for and if necessary installing the Side Steps. Side Steps are missing. Inspect for and if necessary install the Side Steps.
08-112-14
Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.
0811214
Hands Free Feature Inoperative
23-036-14
Water Leak At Hard Top Rear Seam This bulletin involves replacing the hard top. The customer may describe water dripping from the top, running down the inside of the back glass, or running down the inside rear D-pillar.
2303614
Water Leak At Hard Top Rear Seam This bulletin involves replacing the hard top. . The customer may describe water dripping from the top, running down the inside of the back glass, or running down the inside rear D-pillar.
08-106-14
RES RBZ RHB RHR Poor Audio Quality This bulletin involves replacing the radio, if required. A customer may experience, poor audio quality and vehicles with RHB radios may have poor navigation language.
0810614
RES RBZ RHB RHR Poor Audio Quality This bulletin involves replacing the radio, if required. A customer may experience, poor audio quality and vehicles with RHB radios may have poor navigation language.
9003182
Part Description: Hard Top Flipper Glass Prop Rod Issue Description: Having a light oil sheen on the steel shaft of the prop rod is correct and acceptable. Please do not replace the Prop Rod for this condition.
18-068-14
Flash: U0140 Lost Communication With Body Control Module This bulletin involves reprogramming the Powertrain Control Module (PCM) with update software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.
1806814
U0140 Lost Communication With Body Control Module
23-027-14
Zinc Coating Missing From Left Rear Close Out Panel. This bulletin involves inspecting the Julian date on the left rear close out panel. Zinc coating missing from left rear close out panel, no corrosion protection.
2302714
Zinc Coating Missing From Left Rear Close Out Panel
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.