Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
107418
SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH
9100645
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
9100653
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
103954
ACTUATOR - A/C AND HEATER
104087
ACTUATOR - A/C AND HEATER
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100468
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
101232
Plate - Planetary
100192
BOW - FOLDING TOP
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2307000002 REV.B
Suspected Engine Coolant Leak
S1723000037 REV.A
Freedom Panel Underside Rough And Or White Coating Flaking
S2307000002 REV.A
Suspected Engine Coolant Leak
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
S2307000002
Suspected engine coolant leak.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S2208000138RevA
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
9004473
complete wiring harness Before replacing this harness, please check for an available connector repair kit at the following: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S1708000118
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S1708000118 RevB
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
9004378
KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
71838
Warranty Bulletin D-18-16 Rev. B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)
S1908000028 Rev.
(Rev. A) Power Inverter Load Ratings
S1908000102
(Rev. A) Power Inverter Load Ratings
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S2008000108
Rear Wiper Will Not Turn On After Recent Hard Top Removal
S1721000016
Service 4wd Light On, Message AWD System Service Required
S2025000005
Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set
08-052-20
Rear Window Defroster Inoperable This bulletin involves inspecting and possibly repairing the terminal of the rear defroster circuit. Customers may comment on one or more of the following:Rear window defroster is inoperable. Wire(s) hanging from the defroster back glass.
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
D-20-02 Rev. A
DIPAP Requirements - Addition of Jeep Wrangler (JL/JK) and Jeep Gladiator (JT) Hard Top and Targa Top Panel Replacements - All Dealers (Rev. A)
S2008000013
Key Programming, Security Pin Request, Pin Invalid
D-20-02
DIPAP Requirements - Addition of Jeep Wrangler (JL/JK) and Jeep Gladiator (JT) Hard Top and Targa Top Panel Replacements - All Dealers
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9004142
DOOR, Assembly (Front or Rear) For concern of flag nut not aligned to hole, use a blunt tool and lightly tap on the flag nut to knock it loose from e-coat that has dried it in place.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
DOT-L4X8T-04
The SKU is a Tie Rod Center Stud. The Customer commnunication requested return of unsold inventory to inpsect for possible incorrect direction threads (right hand rather than left hand). Incorrect direction threads will prevent it from being installed.
9003293
A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.
0900617
Front Engine Cover Oil Weep This bulletin involves inspecting and replacing the right side front engine cover gasket if necessary. The customer may experience an oil weep from the right front engine cover.
9003511
Console Lid If you are replacing the console lid because it does not open properly or because the button covers are missing, check STAR Parts - there is a button cover replacement kit available. The part numbers for the buttons are as follows: Left - 68359329A$ Right - 68375214A$
9003796
Upper I/Shaft If you have a 2017 Jeep Wrangler (JK) with a clicking sound coming from the steering, please call Jeff Pagel at cell (248) 421-3265 before disassembly. Engineering would like to visit a dealer with a vehicle exhibiting this symptom. If no response in 15 minutes, continue with repair. Send photographs to jeff.pagel@fcagroup.com.
9003782
Reverse Synchronizer If you are working on a 2017 Wrangler that has a customer concern of grinding into reverse or popping out of reverse and the synchronizer has damaged teeth replace the shift fork when doing the repair to the transmission. The 3.6L part number is 68089073AA and the 2.8L diesel part number is 68089072AA
9003723
Amplifier Vehicles needing amplifier replacement, please call Rayyan Mohammed at Cell (248) 954-0790 prior to repair. If no response in 15 minutes, proceed with the repair.
T09
Customer Satisfaction Notification T09 Interior Trim Level About 2,900 of the above vehicles may not have had the correct interior trim feature installed during the manufacturing process. The components such as the front door panels arm rest, center console arm rest, and steering wheel may not have the accent stitching, also the steering wheel spoke bezel may not be satin chrome which is unique to the Rubicon Hard Rock Package edition. Replace the interior trim components that do not have the accent stitching, also the steering wheel spoke bezel that may not be satin chrome.
9003665
Fuel tank and fuel evap system components.
9003768
Fuel Tank 1) Before replacing this part due to fault code P0441, check for restriction due to plastic over-flash in the Purge Hose Port of the Intake Manifold for the ERB (3.6L engine only). If there is flash in the Purge Hose Port of the Intake Manifold, then remove the flash with a 5/32? drill bit and clean the Intake Manifold of any flash debris. 2) Before replacing this part due to ?Hard to Fuel Fill? condition, check the Fuel Filler Tube for restriction in the Vent Tube. If there is blockage, then replace the Fuel Filler Tube. Contact Sylvia H. Lopez at (248) 520-9734 before replacing the Tank. If you do not receive a call back within 15 minutes, then continue the repair.
1807117
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P1239 - Engine Oil Temperature Too Low.
9003752
Stabilizer bar actuator water intrusion Customer comes in with flashing sway bar light and it stays flashing after button reset. If water intrusion or contact pin corrosion is observed on stabilizer bar actuator connector, please call Bing Guo at cell (248) 500-7355 prior to replacing any components. If there is no answer, please verify whether the 50 Way Wiring Kit (P/N 68210289AA) connector has water damage. The Wiring Kit with water damage or contact pin corrosion should be replaced in the same time. Send both stabilizer bar actuator and wiring kit to QEC. If you do not get a response within 15 minutes continue with the repair.
9003065
Swinggate Check Strap When opening the swinggate if the check strap over extends and pulls out, it is necessary to replace both upper and lower swinggate hinges - p/n 55395401A$. Before replacing parts, please call Chuck Hood at Cell (248) 613-7591 regarding Jeep Wrangler Swing-Gate Check Strap and Hinge issues. If no response in 15 minutes, continue with repair.
9003749
RA2 Radio 5" Uconnect Before replacing this radio, make sure you can reproduce the customer issue. If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.
23-029-17
Dimpled Driver Side Front Leather Heated Seat This bulletin involves inspecting and installing heater element patches and replacing seat cushion cover, on the driver?s front seat. The customer may describe, the driver?s front leather seat has dimples in the seat bottom. The dimples are caused by openings in the heated seat element, seeFig. 1.Dimple Location On Leather Seats1 - Dimples
9003413
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
23-028-17
Squeaking Noise Below The Front Seat While Turning and Going Over Bumps This bulletin involves replacing the bolt and bushing on driver and passenger side seat slide mechanism to resolve a squeaking issue (Two door models only). The customer may describe a squeak heard under the front passenger or driver side seat, while turning or driving over bumps.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
9003699
Heated Seat Elements; Cushion and Back DEALERCONNECT HEATED ELEMENT RESISTANCE INFO OUT IS OF SPEC. Prior to ordering any of the parts (55057300A$, 55057293A$, 55057301A$, 55057294A$) Please contact Micah Straub at cell phone# 248-613-2478 for further instructions. Leave a voice mail and your call will be returned promptly. 5.1 to 7.8 is the correct resistance value although ambient temperature will affect this value. Please call for detailed information. If no return call in 15 minutes, proceed with repair.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003688
Header Weatherstrip, Center Targa Top Seal, Right Door Mounted Weatherstrip Water leak from the Freedom Panels at the rearview mirror/drops down on the instrument panel/radio area OR Water leak at the right front A pillar/on the passenger's side floor, please contact Kayla Branton at cell (248) 224-8272. If no response in 15 minutes, please proceed with repair
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9002718
Hands Free Module - Convergence Telematics Module (CTM) Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
9002831
Water Pump For JK Bodies ONLY: If replacing the water pump for a chirp, squeal or NVH, please contact either: Nick Morand cell: (248) 410-5078 nick.morand@fcagroup.com Joe Lovell cell: (734) 309-6467 joe.lovell@fcagroup.com Engineering is seeking audio recordings of the concern in an effort to root cause and make necessary improvements to future pumps. Please email any audio recording or documentation of when/where/how the pump makes noise to the above emails. If the dealer is located in the Detroit Metro Area, Engineering may send a representative to review with technician. Any information is appreciated. If a response is not received within 15 mins , then proceed with the necessary repair. For JK and DS: Before replacing water pumps for noise issues the heat shield on the catalytic converter needs to be checked to make sure it is not the source of the noise. Check while the engine is fully warmed up. If the heat shield is found to be the source of the noise tighten the bolts and, or add shims/washers as needed.
9003231
RHB/RBZ Radio For JK, MK, and RT ONLY: RHB/RBZ radio that supports Bluetooth and Hands- Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE
9003639
Fuel Tank Pressure Sensor and Purge Valve Canister Before replacing this part due to fault code P0441, please call David Thomas at cell (248) 613-6908. Engineering may want to visit dealers in the metro Detroit area with this condition. If you don't receive response within 15 minutes, please continue with normal repair procedure.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
68232614A$
Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.
1PH98RXFA$
PANEL, Targa Top, Complete with Hardware For water sloshing noise in the Targa Top Panel, do not replace the panel. There is a drain hole along the rear edge of the panel (in car position). After draining the panels, inform the customer of the drain hole and if the issue returns they can drain the panels themselves. Storage of panels outdoors in certain positions will cause water infiltration.~ ~ For a water leak from the center front edge of the Targa Top Panels, do not replace the panels, replace the SEAL, Targa Top (Part Number 68088055AA).
Panel
Parts.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.