S2609000011
Service Bulletin/Repair Instructions
MIL-On and/or Engine Oil Leak
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2609000011
MIL-On and/or Engine Oil Leak
9100900
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S2623000048 REV.A
Customer States Driver Seat inoperative. Seat Fuse F59 30A Found blown.
9100363 Rev 3
Turbocharger Kit Please note that many turbo components are serviceable separately and full turbo replacement may not be required. If the turbo is being inspected for: Noise/Rattle: Inspect heat shield fasteners for looseness and check the wastegate actuator/linkage for binding. The actuator kit is serviced separately. Oil Leak: Inspect the turbo oil feed O-ring area for leaks. O-ring is serviced separately.
23-036-26
Water Leak In Rear Cargo Area Customers may comment on the following: SYMPTOM: ● Water leak in the rear cargo area.
S2623000048
Customer States Driver Seat Inoperative.
113792
PAD - INSTRUMENT PANEL
9100872
Display Exchange part has been superseded. Order the latest Z part number: Z8607669AC --> Z8791155AA (Active Exchange Part) Z8607669AD --> Z8791669AA (Active Exchange Part) Z8607669AE --> Z8791156AA (Active Exchange Part) Z8607671AC --> Z8791157AA (Active Exchange Part) Z8607671AD --> Z8791158AA (Active Exchange Part) Z8607671AE --> Z8791159AA (Active Exchange Part)
9100840
Switchbank 4 gang The customer will notice either one or two of the following conditions: 1. Fuel Door is Not opening when Fuel door Switch is pushed. Technician Observe the DTC P04CB-FUEL FILL DOOR OPEN REQUEST SENSOR-SWITCH CIRCUIT HIGH. 2. Drives Modes do not work when Switch is pressed (Hybrid, Electric, E-save). Technician Observe DTC U113B-LOST COMMUNICATION WITH SWITCH BANK MODULE. Procedure: If during vehicle Scan diagnostics besides DTC's P04CA, P04CB or U113B. there are another DTCs Repair it First accordingly. DTC's may be related to main ECU's like: HCP, BCM, PCM, etc. If DTC P04CB and/or U113B are still present, then follow the following action before replacing the Switch: 1. Read vehicle DTCs while the IGN ON. 2. Verify ESBM feed fuse state. Replace the fuse if needed. 3. Wiggle the ESBM harness takeout (LIN and ESBM feed takeout) and monitor the state of DTC P04CB and/or U113B. o If this step affects DTC P04CB and/or U113B. behavior, the issue is likely related to a failure in the harness. 4. Disconnect the harness from the ESBM and confirm there not any damage, like bend PINs, corrosion, etc. 5. Confirm Harness continuity. 6. Verify power to ESBM by back probing the ESBM connector o If voltage is lower than 11.8V, follow normal procedures for low batteries. - If there no damage in the harness nor the connector and pins of the ESBM, reconnect it ensuring the harness connector is being fully engaged into the ESBM connector. 7. Confirm Continuity of the harness from the ESBM connector to the BCM connectors. 8. Reconnect the ESBM and then Verify LIN bus activity with Mopar scope. o Config scope to LIN monitor if feasible. o Replace the ESBM only based confirmation from the LIN diagnostic. 9. With the scan tool, read DTCs. If still DTC are set, replace ESBM (Fuel door and drive modes Switch module) in accordance with the Service Information. Flag the part to be returned to supplier for further part analysis.
9100533 Rev 1
DCSD Before replacing this part for a Blank screen, screen flickering or screen inoperative concern, perform a hard reset to the Display and see if concern is resolved. Currently no dealer claims with this issue stating the RVC image is affected. Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only. Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only. Exchange Part Number Supersession For Ordering: 68607669AC --> Z8607669AC --> Z8791155AA 68607669AD --> Z8607669AD --> Z8791669AA 68607669AE --> Z8607669AE --> Z8791156AA 68607671AC --> Z8607671AC --> Z8791157AA 68607671AD --> Z8607671AD --> Z8791158AA 68607671AE --> Z8607671AE --> Z8791159AA
113270
CORE – HEATER
113271
CORE – HEATER
9100833 REV1
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S2508000025 REV. B
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
113152
THERMOSTAT – NONE.
113153
THERMOSTAT – NONE.
112639
THROTTLE BODY – NONE
112640
THROTTLE BODY – NONE
S2508000025 REV.A
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
112862
MOTOR - BLOWER WITH WHEEL
112863
MOTOR - BLOWER WITH WHEEL
112842
BOLT - HEX FLANGE HEAD
9100833
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S268A000014
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
112856
HEATER - ELECTRIC COOLANT
112857
HEATER - ELECTRIC COOLANT
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
111760
MOTOR AND LINKAGE - WINDSHIELD WIPER
112203
SWITCH - STEERING WHEEL
112202
SWITCH - STEERING WHEEL
21-041-26
Transmission Auxiliary Oil Pump Failure Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: ● Vehicle is in limp mode This bulletin involves replacing the transmission oil pump.
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
09-009-26
PHEV Engine Replacement XC2 Warranty Extension Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P2336 - Cylinder 1 Above Knock/Combustion Vibration Sensor Threshold. ● P2337 - Cylinder 2 Above Knock/Combustion Vibration Sensor Threshold. ● P2338 - Cylinder 3 Above Knock/Combustion Vibration Sensor Threshold. ● P2339 - Cylinder 4 Above Knock/Combustion Vibration Sensor Threshold. The customer may also describe the following: ● A knocking noise from the engine compartment This bulletin involves replacing the engine.
111833
SENSOR – KNOCK
111834
SENSOR – KNOCK
112147
D-26-11 (XC2) 2.0L PHEV Engine - Select 2024 - 2025 Jeep Wrangler (JL) and 2023 - 2025 Grand Cherokee/ Grand Cherokee L (WL)
112149
ID-26-24 (XC2) 2.0L PHEV Engine - Select 2024 - 2025 Jeep Wrangler (JL) and 2023 - 2025 Grand Cherokee/ Grand Cherokee L (WL)
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
08-207-26
Instrument Panel Cluster (IPC) Flicker Turn By Turn The customer may experience flickering on their Instrument Panel Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay
S268A000013
Radio Volume Jumping Up To Max Volume After Radio Wake Up
18-003-26 REV A
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating).** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. (Manual Transmission Only) ● P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0152-02 - O2 Sensor 2/1 Circuit High. ● P0158-02 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/System Voltage High. Customers may also comment on one or more of the following: ● **The vehicle has a rough idle. ● The engine has a miss or runs rough. ● Noisy valvetrain. M18 FSAR-TSB-7163 -2- ● "Service Transmission" message in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutra
111405
COVER - CYLINDER HEAD
111406
COVER - CYLINDER HEAD
S2623000018
Wind Noise From Hard Top Freedom Panels Near Rear View Mirror While Driving.
08-133-26
Rear Defroster Inoperative Customers may experience one or more of the following: SYMPTOM: ● Rear window is not defrosting. ● The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window.
08-134-26
Universal Garage Door Opener (UGDO) Inoperable Technicians may or may not find the following Diagnostic Trouble Code (DTC) present: SYMPTOM: ● B251D1-00 - Universal Garage Door Opener Control. Customers may comment on the following: ● Operational questions regarding the usage of the HomeLink® UGDO. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
08-121-26
Flash: Comfort Seat Wheel Module (CSWM) Update Customers may experience the following: SYMPTOM: ● Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.
S248A000006 REV.A
Radio screen goes blank or cuts in and out
9100773
Disengaging Stabilizer Bar Front [SHG] 1. Follow procedure in SOL s2602000001 before replacing Smart Stabilizer Bar Assembly 2. If the ends of the stabilizer bar are rusted, DO NOT REPLACE THE STABILIZER BAR. The bar ends are currently masked to protect against excessive powder coats, which may lead to minor surface rust.
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2602000001
Service Electric Sway Bar Lamp On In Cluster. Diagnostic Trouble Code (DTC) C008E-00 In Auto Sway Bar (ASBS)
S2608000004
Remote Keyless Entry, Passive Entry, Remote Start Inoperative or a Cluster Message “Keyfob Not Detected”
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
23-005-26
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: SYMPTOM: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2610000002
2 nd Row Center Seatbelt Jammed Or Stuck. Webbing Twisted.
110405
GLOVE BOX - INSTRUMENT PANEL
110406
GLOVE BOX - INSTRUMENT PANEL
110626
PANEL - FRONT SEAT BACK
110399
HANDLE - INSIDE RELEASE
110400
HANDLE - INSIDE RELEASE
S2603000001
A suspected leak may be noticed on the front or rear axle pinion seal.
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
31-001-26 REV.A
Door Hem Aluminum Body Panel Corrosion Repair Customers may experience the following: SYMPTOM: ● Filifom corrosion at the hem area of the door. This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.
S228A000025 REV.A
Harman R1H Uconnect 5 Radio Software Flash Error Codes
110462
D-25-15 Rev. B Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
110469
ID-25-11 Rev. B Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
S268A000008
Uconnect Box Requires Service, Please Visit an Authorized Dealer Message on Display Message With DTCs B1498-13, B1498-19 or B1570-93
110429
Warranty Newsletter – Volume 12, Issue 2
110431
FCA Caribbean Warranty Newsletter – Volume 12, Issue 2
S2423000027 REV.D
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
31-001-26
Door Hem Aluminum Body Panel Corrosion Repair Customers may experience the following: SYMPTOM: ● Filifom corrosion at the hem area of the door. This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.
9100591 Rev 1
Universal Garage Door Opener Prior to replacing the UGDO or sun visor, call HomeLink® Customer Care at 1-800-355-3515 for a proper evaluation of the issue. If this does not correct the issue, please follow the steps in SOL: S2508000039
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2408000024 REV.B
Power Top Switch Unresponsive, Full Retractable Sky Roof Does Not Open or Close
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
9100756
DO NOT REPLACE MULTIPLE SHOCKS UNLESS ALL ARE VERIFIED TO BE DEFECTIVE. Reference Master Tech article released in January 2026 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm
S2607000003
GMET4 DOHC Water Pump Coolant Leak Inspection
109607
CALIPER ASSEMBLY - DISC BRAKE
109986
SWITCH - LUMBAR CONTROL
S2607000002
Hemi Water Pump Coolant Leak Inspection
109820
SEAL - ROOF RAIL
109822
SEAL - ROOF RAIL
18-003-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. **(Manual Transmission Only)** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on the following: ● "Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection **(Manual Transmission Only). NOTE: Customers might experience wheel spin or slippage and the PCM could interpreted the wheel spin or slippage as slipping the clutch too much and to avoid clutch damage, the customer may see the message in the IPC.** ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear) **(Manual Transmission Only)**. ● Vehicle runs rough. Other software enhancements include: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 heater crack improvements. ● OBD software changes. statement. Revisions not highlighted by asterisks include removal of a Sale Code. M18 FSAR-TSB-6879 -2- This Technical Service Bulletin (TSB) has also been released as a Rapid Service Update (RSU) 24-109, date of issue August 01, 2024. All applicable RSU VINs have been loaded. To verify this RSU service action is applicable to the vehicle, use VIP or perform a VIN search in DealerCONNECT/Service Library. All repairs are reimbursable within the provisions of warranty. REPAIR SUMMARY: **This bulletin involves inspecting and possibly reprogramming the PCM with th
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
08-012-26
Speaker Diagnostic Procedure Rattle, buzz and squeak coming from specific speakers.
9100749
axle seal We have observed that some JL/JT rear axle shafts are leaking oil. Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.
109281
CENTER STACK – NONE
109227
DOOR - FUEL FILL
109228
DOOR - FUEL FILL
9100738 Rev 1
Issue Description: In JL/JT vehicles, many dealers and customers are not fully aware of the correct way to install the Mopar all-weather floor mats, especially the front mats. The all-weather mats are installed without removing the slit/perforation portion of the front carpet, which blocks the drain port on the all-weather mats completely and does not allow water/any liquid to get drained out of the vehicle through the drain hole on the underbody floor. Correct Installation Method for Mopar All-Weather Floor Mats 1. Find the slit/perforation on the front carpet (near the outboard mat post on the carpet )and cutout that piece from carpet. 2. Remove Drain Plug on the drain hole on the underbody floor 3. Install the All-Weather Mat. Make sure the mats built-in drain port lines up correctly into the drain hole on the floor. 4. Insert the drain plug in the drain port on all-weather mat to close the drain port. The plug is to be removed whenever there is need to drain water on the mat or to wash out dirt without removing the mat form the vehicle.
08-394-25 REV. A
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure.
S2523000096
CEL (Check Engine Lamp)/ Brake lamp Illuminated. Diagnostic Trouble Code (DTC) P083F- Clutch Pedal Position Sensor Performance.
9100734
If the DTC B1E21-96: Backup Battery-Component Internal Failure is active and customer states Popup message will show at the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
9100738
Issue Description In JL/JT vehicles, the front carpets have a perforated section below the drain plug instead of a fully punched-out hole. This causes several problems: . Dealers often install all-weather mats without removing the carpet cutout, which completely blocks the drain. . Missing drain plug claims occur because the plug is not clearly visible. . Customers find it difficult to locate and access the drain plug, especially when the vehicle is muddy. Correct Installation Method for Mopar All-Weather Floor Mats To ensure proper drainage, follow these steps: 1. Identify the Issue: . Some owners place the all-weather mats directly over the carpet, blocking the drain hole even though the mat has a drain port. 2. Locate the Carpet Cutout: . Under the mat area, there is a pre-cut carpet section designed to be removed. 3. Remove the Carpet Piece and Plug: . Lift or cut out the small square of carpet to expose the metal floor. . Remove the rubber drain plug from the Jeeps floor. 4. Install the Floor Mat: . Place the all-weather mat back into position. . Align the mats built-in drain tube with the drain hole on the floor to form a proper seal. 5. Reinstall the Plug into the Mat: . Insert the drain plug (removed from the floor) into the drain hole on the mat. . This allows you to open the plug anytime to wash out dirt or water without removing the mats. Benefits . Enables washing the mats with a hose while they remain inside the vehicle; water drains directly to the ground instead of soaking the carpet. . Prevents water from getting trapped under the mat, avoiding carpet damage.
08-394-25
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present echnicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure
108893
MICROPHONE - AUDIO
S1819000004 REV.R
Shimmy Felt In Front End
108894
MICROPHONE - AUDIO
S2524000015
Temperature Control Display Is Showing Incorrect Values In Climate Widget.
S258A000021
Diagnostic Trouble Code (DTC) B15A1-00 Media Port Connection 1 Connection Found Set.
108544
SWITCH - POWER WINDOW
108463
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
18-092-25 REV. A
Not applicable to vehicles built for US market. Flash: Powertrain Control Module (PCM) Updates Customers may experience the following: ● Momentary hesitation in the engine when the vehicle is shifting from 3rd to 4th gear under light load and light acceleration. This occurs primarily between 1,600 and 2,100 RPM. Feels like an engine stumble or a misfire. This bulletin involves reprogramming the PCM with the latest available software.
108464
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108458
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
108461
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
9100723
1.Identify Customer Concern Check for small traces of coolant near the water pump, especially around the weeper chamber. Confirm if coolant is visibly dripping from the weeper chamber. 2.Root Cause identification The weeper chamber is designed to collect small amounts of coolant (< 3 ml/h) that pass through the dynamic seal. Red traces or shadows around the chamber may appear during initial operation due to seal adaptation or vapor condensation. These traces are not necessarily signs of a leak. Continuous dripping of coolant, however, indicates a malfunction. 3.Service Repair Procedure Lift the vehicle using an elevator. Verify if coolant is actively dripping from the weeper chamber. Run the engine at idle, alternating speed between 2000 4000 rpm for 15 minutes. Observe the weeper chamber during this test: If coolant continues to drip: Replace the water pump (possible permanent damage to the dynamic seal). If dripping stops: No further action is needed; the vehicle can be returned to the customer. 4.Clarify Leak Sources Do not confuse leaks from: The Press-In-Place rubber gasket (between water pump and engine block), or The inlet pipe nipples with leaks from the weeper chamber.
08-369-25
SOS Light Is On Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B143A-13 - Microphone 1 - Circuit Open. ● B143D-13 - Microphone 2 - Circuit Open. Customers may also comment on one or more of the following: ● SOS light is illuminated. ● Customer can hear incoming calls but can't be heard on the other end. This bulletin involves replacing the **Microphone, Audio** assembly.
18-092-25
Not applicable to vehicles built for US market. If not in us market place in concise summary Flash: Powertrain Control Module (PCM) Updates Customers may experience the following: ● Momentary hesitation in the engine when the vehicle is shifting from 3rd to 4th gear under light load and light acceleration. This occurs primarily between 1,600 and 2,100 RPM. Feels like an engine stumble or a misfire This bulletin involves Inspecting and possibly reprogramming the PCM with the latest available software.
S2508000100
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S1805000006 REV.B
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
23-019-25 REV. B
Not applicable to vehicles built for US market. Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0133 - O2 Sensor 1/1 Slow Response. ● P2251 - O2 Sensor 1/1 Negative Current Control Circuit/Open. ● P0131 - O2 Sensor 1/1 Circuit Low. ● P2626 - O2 Sensor 1/1 Pump Cell Current Trim Circuit/Open. ● P0607 - ECU Internal Performance. ● C140A - Transfer Case Motor Control. ● P02EE - Cylinder 1 injector Circuit Performance. ● P02EF - Cylinder 2 injector Circuit Performance. ● P02F0 - Cylinder 3 Injector Circuit Performance. ● P02F1 - Cylinder 4 Injector Circuit Performance. ● U0109 - Lost Communication With Fuel Pump Control Module. ● P0330 - Knock Sensor 2 Circuit. ● P023B - Charge Air Cooler Coolant Pump "A" Control Circuit Low. ● P2110 - Electronic Throttle Control - Forced Limited RPM. Customers may also experience one or more of the following: ● The electronic throttle inspection required indicator illuminates on the Instrument Panel Cluster (IPC). ● Seatbelt warning light and warning sound do not go off even when the passenger seat belt is fastened. ● Coolant leak from under the long life coolant reserve tank. ● Fuel cap strap broken. ● Door not opening / hard to open for both right side doors. ● Lumber switch inoperative. ● Right front seat cover stitch is tore out. ● Header seal deformation. This bulletin involves performing multiple inspections and repairs based on the listed Customer Symptoms.
S2509000009
Engine Oil Leak
S2508000091
Radio (ETM) Is Always Setting Stored DTC B15A1-00 Media Port 1 Connection
S2508000088
Vehicle Complaints After a Recent Firmware Over The Air (FOTA) Update for the Telematics Box Module (TBM)
9100684
When servicing/replacing 68415437A$ Transmission, take care to not damage the PIM to P2 harness. Also, when reinstalling the harness, route the harness properly and secure it at all the retention points.
105646
MODULE - STEERING CONTROL & COLUMN
9100325 Rev 1
Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.
9100677
Power top /sky one touch switch falls out of the bezel or is pushed inside it or won't stay in place. Or if there's miscalibration in the power top. If the switch has no physical damage, is not broken or separated, but still doesn't stay in place, verify that the bezel brackets that hold it in place are broken and are the cause of the problem. If the bezel is broken, and the switch is not, replace only the bezel trim, DO NOT replace the switch. If there's miscalibration in the power top, and there's no physical damage to the switch and it works accordingly, DO NOT replace the switch.
23-033-25
Not applicable to vehicles built for US market. Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U11E3-00 - TCM Lost Communication With ESM On DPT CAN. ● B15A1-00 - Media Port 1 Connection. ● U11C2 - Lost Transmission Message. ● U11E4-00 - CAN Communication Messages Missing. ● U120C - Lost Brake Booster Signal. ● U1216-00 - Lost Communication With DASM. ● U121E-00 - Lost Communication With Steering Wheel Cruise Control Switch. ● U1267-00 - No Valid Data From ESM On CAN-C Or CAN-DPT. ● U12A8 - Lost Communication With Master Cylinder Pressure Sensor. ● U1465-00 - Implausible Driver Shift Request Signal Received. ● U1466-00- Implausible Driver Shift Request Signal Received On DPT CAN. ● U1515-87 - Steering Column Lock Secret Code - Missing Message. ● U1517-87 - Body Controller Secret Code - Missing Message. ● B2206-00 - Current VIN Missing/Mismatch. ● B2225-00- ( SCM) Steering Column Module Internal. ● C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. ● P0607-00 - ECU Internal Performance. ● P1DD2-00 - Torque Request Signal From TCM Denied. ● U0100-00 - Lost Communication With ECM/PCM. ● U0101-00 - Lost Communication With TCM. ● U0102-00 - Lost Communication With Transfer Case Control Module/AWD. ● U0103-00 - Lost Communication With Electric Gear Shift Module. ● U0121-00 - Lost Communication With Anti-lock Brake System (ABS) Control Module. ● U0125 - Lost Communication With Dynamics Sensor. ● U0129-00 - Lost Communication With Brake System Control Module. ● U0140-00 - Lost Communication With Body Control Module. ● U0151-00 - Lost Communication With Occupant Restraint Controller (ORC). ● U0155-00 - Lost Communication With Cluster/CCN. ● U0159-00 - Lost Communication With Parking Assist Control Module. ● U017E - Lost Communication With Seatbelt Sensor 1. ● U0212-00 - Lost Communication With Steering Column Control Module. ● U0213-00 - Lost Communication With Interior Mirror Control Module "A". ● U0415-00 - Implausible Data Received From ABS. ● U0418-86 - Implausible Data Received From Brake System Control Module 1 - Signal Invalid. ● U0422-00 - Implausible Data Received From Body Control Module. ● U110A-00 - Lost Communication With SCM-CAN-C. ● U110C - Lost Fuel Level Message. ● U110E - Lost Ambient Temperature Message. ● U1110-00 - Lost Vehicle Speed Message. ● U1120 - Lost Wheel Distance Message. ● U113E-00 - Lost Communication With Intelligent Battery Sensor. ● U114C-00 - Lost Communication With PRNDL Display. ● U115F-00 - Lost Communication With Driver Presence Detection Module. ● U1175-00 - Lost Ignition Status Message. ● U1186 - Lost Communication With Adaptive Cruise Control Module. ● U1199 - Lost Hood Ajar Switch Voltage Message. ● U11B9-00 - Lost Communication With RF Hub. ● U11BC - Lost Brake Switch Message. ● U11BF - Lost Brake Pedal Position Message. ● P2453-00 - Differential Pressure Sensor A Circuit Range/Performance. ● P245F-00 - Diesel Particulate Filter Pressure Sensor "B" Circuit. ● C140A-11 - Transfer Case Motor Control. Customers may also experience one or more of the following: ● Android Auto not working. ● Radio screen is black for one to two seconds while driving and then returns to normal operation. ● Transfer Case Control Module (TCCM) wiring incorrectly routed. ● Noise from the front axle. ● Decals on the left and right fenders are peeling off. ● Right hand side speaker not working or exhibits a rattle noise. ● USB port not working. ● Interior rearview mirror delaminating. ● Tailgate glass damper mounting is peeling off or has come off. ● Abnormal noise from chain tensioner. ● Radio control on steering wheel malfunctions or has a delay in response This bulletin involves performing multiple inspections and repairs based on the listed Customer Symptoms.
23-034-25
Not applicable to vehicles built for US market. Parking Brake Will Not Release Customers may comment on the following: ● Park brake will not release. This bulletin involves using glue to repair the park brake handle positioning.
9100670
Data collection required for all 2020-2026MY vehicles with 3.6L PSU engines during any of their first 3 engine oil changes. This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.
S2218000003 REV.B
Customer complaint may include a Mil On/Check Engine Lamp On and Electronic Throttle Control (ETC) Lamp On. There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:
107418
SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
S2508000068
Instrument Panel Cluster (IPC) Display Flickers, Overlapping Displayed Images, Multiple Warning Lamps Turn on And Off
S2522000001
TPMS Handling & Installation Best Practices
S2522000002
Customer Indicates Tire Pressure Monitoring System (TPMS) Lights On Dash.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
9100649
False fails on PCR, DBSM and PDCs Stuck Closed or open diagnostics, DTC P2AF5 or P2AF6, leading to NTF and unnecessary replacements. Current controls are not robust against depleted auxiliary battery condition. Please follow SOL S2508000031.
9100651
False fails on PCR, DBSM and PDCs Stuck Closed or open diagnostics, DTC P2AF5 or P2AF6, leading to NTF and unnecessary replacements. Current controls are not robust against depleted auxiliary battery condition. Please follow SOL S2508000031.
9100654
Before replacing the key fob battery, please follow the following steps: 1- Check if there is a "FOB Low Battery" msg on the instrument cluster 2- Check if there is a fob Low battery active DTC Fob battery 1 DTC B1A10-00 or Fob battery 2 DTC B1A11-00 3- Check if the original battery is installed which Varta or Panasonic sized CR 2450 4- Verify if the fob ID printed under the battery cover matches fob IDs stored in the RFHUB, use DID $A004 - Engineering Development Data 1 (FOB ID 1 & 2) to check the fob IDs in the RFHUB 5- Check the voltage of the coin battery, replace the battery only if the voltage is 2.3V or below and report the voltage in the dealer narratives
S258A000019
Radio Does Not Turn On Automatically When Vehicle Is Started
18-011-25 REV. B
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0133 - O2 Sensor 1/1 Slow response. ● P2453 - Particulate Filter Pressure Sensor “A” Circuit Range/Performance. ● P245F - Particulate Filter Pressure Sensor “B” Circuit Range/Performance. ● P0420 - Catalyst System Efficiency Below Threshold Bank 1. ● P0017 - Crankshaft/camshaft Timing Misalignment - Bank 1 Sensor 2. ● P000A - Bank 1 Camshaft 1 Position Slow Response. ● P219A - Bank 1 Air-fuel Ratio Imbalance. Customers may also experience the following: ● A no crank/no start condition. In addition, the following software enhancement is available: ● Smart charge change: Battery life improvements. This bulletin involves possibly replacing the Oil Control Valves (OCVs), and/or the Catalytic Converter and also reprogramming the PCM with the latest available software
03-003-25 REV. A
Not applicable to vehicles built for US market. Rear Axle Noise Customers may experience the following: ● Intermittent grinding, screeching, ratcheting noise coming from the right hand side of vehicle on the rear axle This bulletin involves cleaning and lubricating the axle shaft and hub splines.
106348
DAMPER - STEERING
106349
DAMPER - STEERING
S2509000001 REV.B
Engine Rattle Noise
18-011-25 REV. A
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0133 - O2 Sensor 1/1 Slow response. ● P2453 - Particulate Filter Pressure Sensor “A” Circuit Range/Performance. ● P245F - Particulate Filter Pressure Sensor “B” Circuit Range/Performance.** ● P0420 - Catalyst System Efficiency Below Threshold Bank 1. ● P0017 - Crankshaft/camshaft Timing Misalignment - Bank 1 Sensor 2. ● P000A - Bank 1 Camshaft 1 Position Slow Response. ● P219A - Bank 1 Air-fuel Ratio Imbalance. Customers may also experience the following: ● A no crank/no start condition. In addition, the following software enhancement is available: ● Smart Charge change: Battery life improvements This bulletin involves possibly replacing the Oil control valves (OCV)s, and/or the Catalytic Converter and also reprogramming the PCM with the latest available software.
23-006-25 REV. B
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield.
S2422000001 REV.D
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
09-018-25
Engine Cylinder Block Porosity Inspection - Engine Cold Start Rough Idle Customers may experience the following: ● Rough engine idle when cold starting the engine. ● Low coolant level in coolant recovery bottle.
105648
MODULE - ENGINE CONTROLLER
18-008-25 REV. A
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation.** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● "Service Transmission” message on in the Instrument Panel Cluster (IPC). ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other software enhancements included: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 heater crack improvements. ● OBD software changes. This bulletin involves reprogramming the PCM with the latest available software.
21-009-25 REV. C
850RE D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100622
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
23-026-25
Overhead Sound Bar Rattles Or Buzzes Customers may experience the following: ● Overhead sound bar speaker assembly buzzes or rattles This bulletin involves applying a foam strip to the back side of the sound bar speaker assembly.
105288
VALVE - CHECK
105647
RAIL - REAR
21-026-25 REV. B
Shifter Inoperative Customers may comment on one or more of the following: ● The vehicle can't be shifted out of Park or current selected gear. ● "Service Shifter, Stop Safely, Shut Off Engine To Engage Park" message displayed on the Instrument Panel Cluster (IPC). NOTE: Auto park will engage once the driver seat belt is unbuckled and the driver door is opened. This bulletin involves inspecting transmission shifter operation and possibly replacing the transmission shifter.
9100614
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
105590
Warranty Newsletter – Volume 11, Issue 6
105591
FCA Caribbean Warranty Newsletter – Volume 11, Issue 6
OTHERDOC_133
Global Telematics Box Module Over The Air Update from 5.39.1 to 5.65 TBM2.0 Software Version (FOTA) Customers may experience one or more of the following: - Error display of "Uconnect Box Requires Service/Wifi Unavailable" popups; [ TBM DTC B22A9-96 Internal Performance Failure ]. - Error display of "Uconnect Box Requires Service" pop-ups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ].
9100605
Shim - felt GIM # NUSENGCHR24018991: JL JT sun visor center support BSR. Add felt shim 68736674AA - 43MM OD x 10mm ID x 1mm thick.
21-026-25 REV. A
Shifter Inoperative Customers may comment on one or more of the following: ● The vehicle can't be shifted out of Park or current selected gear. ● "Service Shifter, Stop Safely, Shut Off Engine To Engage Park" message displayed on the Instrument Panel Cluster (IPC). This bulletin involves inspecting transmission shifter operation and possibly replacing the transmission shifter.
08-178-25
Motor Generator Unit (MGU) Replacement Customers **must** experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician **must** find the following Diagnostic Trouble Code (DTC) has been set: ● P1B0F-00 - Drive Motor A Position Sensor Offset Incorrect. Customers may also experience one or more of the following: ● Vehicle goes into limp home mode. ● Vehicle does not start. This bulletin involves inspecting the MGU serial number and possibly replacing the MGU as needed.
9100599
Underhood start/stop safety The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.
S2408000024REVA
Power Top Switch Unresponsive, Full Retractable Sky Roof Does Not Open or Close Customer Complaint/Technician Observation: The owner complains the top system is inoperative and that by pressing the switches the Power Top does not make any movement. Technician may or may not have Diagnostic Trouble Codes (DTCs). Repair Procedure: Perform the power top calibration prior to any switch or parts replacement.
104966
BEZEL & INDICATOR- GEAR SHIFT INDICATOR
18-026-25
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P2450 - Fuel Tank Isolation Valve Stuck Open.** ● P0032 - O2 Sensor 1/1 Heater Circuit High. ● P2097 - Downstream Fuel Trim System 1 Rich. ● P0171 - Fuel System 1/1 Lean. ● P0300 - Multiple Cylinder Misfire. ● P06E4 - Control Module Wake-Up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. Customers may also experience one or more of the following: ● **"Service Hybrid System" message displays on the Instrument Panel Cluster (IPC). ● Wrench icon displays on the IPC.** ● Vehicle misfires. ● Low speed engine stall at idle. ● Difficulty shifting out of 4LO. ● Idle creep while in 4LO with transmission in neutral. **This bulletin involves reprogramming the Powertrain Control (PCM) and the Auxiliary Hybrid Control Processor (AHCP) also known as Power Inverter Module (PIM) and possibly the Transmission Control Module (TCM) with the latest available software.**
02-002-25
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
9004003
Backlite Heated Liftgate Glass Assembly: For rear window defrost inoperative concerns where heated glass electrical tab has become detached, it is not necessary to replace the glass assembly. For loose or detached electrical tab, refer to TSB 23-007-25 for repair procedures on reattaching a loose tab. For burned or discolored gridlines on hard tops, DO NOT change the complete Flipper glass assembly. This discoloration is oxidation of the ceramic silver material and is normal. The Engineering standard call out the fact that this bus bar will change in color and is not a deterioration of the material or performance.
S2523000049
B2779-04 Vehicle Pedestrian Alert Module-System Internal Failures. Quiet Vehicle Pedestrian Module (QVPM) Sound Is Not OK. Discussion: If diagnostic trouble code (DTC) B2779–04 is present and or QVPM is inoperative or sound is not okay, before replacing the module please check first the following service instructions: Perform the BODY VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Body Control (BCM) - Standard Procedure).
09-011-25
Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise.
S2508000039
Universal Garage Door Opener (UGDO) Inoperative, LED Indicator Lamps Not Illuminating
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
9100498 Rev 3
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
9100534 Rev 1
Transmission "Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
9100570
Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible "glitter" or debris in the pan does not justify complete unit replacements.
08-155-25
Global Telematics Box Module (TBM) Firmware Over The Air (FOTA) Update 2023 - 2025 (JL) Jeep Wrangler 2023 - 2025 (JT) Jeep Gladiator This bulletin applies to vehicles built on or before May 05, 2025 (MDH 0505XX) equipped with Global Telematics Box Module (TBM) (Sales Code RDG). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.15, 5.41 or 5.43 to 5.53 software level
08-151-25
Flash: Radio Frequency Hub Module (RFHM) Updates Customers must experience the following: ● Customers may be concerned about vehicle theft due to ability of key FOBs to be programmed through RFHM. Software enhancement includes: ● Update to the RFHM software to prevent hackers from programming their own key fob to the vehicle. ● This is intended to deter an unwanted drive off of the vehicle without the customer's knowledge This bulletin involves updating the RFHM module with the latest available software.
03-003-25
Rear Axle Noise Customers may experience the following: ● Intermittent grinding, screeching, ratcheting noise coming from the right hand side of vehicle on the rear axle This bulletin involves cleaning and lubricating the axle shaft and hub splines.
S2523000039
Steering Column Difficult To Adjust Up Or Down.
08-131-25
R1H Radio Over The Air Update U33.43 and U35.18 To U Customers may experience one or more of the following: ● Pop-up messages text cut-off "Transfer to Passenger". ● Missing active call details in phone widget after swap is performed. ● Missing Pop-up messages for Blind Spot related to Lane Management on/off. ● Virtual wall option in menu present (should be removed). ● Customer need to select Sound type in EV pages twice. ● Apple Car Play icon on main screen disapears when ACP is activ This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from U33.43 and U35.18 To U37
S2008000103 REV.B
No Start, Stop Start Inoperative, Battery or Check Engine Light (CEL) Illuminated
23-019-25 REV.A
Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0133 - O2 Sensor 1/1 Slow Response. ● P2251 - O2 Sensor 1/1 Negative Current Control Circuit/Open. ● P0131 - O2 Sensor 1/1 Circuit Low. ● P2626 - O2 Sensor 1/1 Pump Cell Current Trim Circuit/Open. ● P0607 - ECU Internal Performance. ● C140A - Transfer Case Motor Control. ● P02EE - Cylinder 1 injector Circuit Performance. ● P02EF - Cylinder 2 injector Circuit Performance. ● P02F0 - Cylinder 3 Injector Circuit Performance. ● P02F1 - Cylinder 4 Injector Circuit Performance. ● U0109 - Lost Communication With Fuel Pump Control Module. ● P0330 - Knock Sensor 2 Circuit. ● P023B - Charge Air Cooler Coolant Pump "A" Control Circuit Low. ● P2110 - Electronic Throttle Control - Forced Limited RPM. Customers may also experience one or more of the following: ● **The electronic throttle inspection required indicator illuminates on the Instrument Panel Cluster (IPC).** ● Seatbelt warning light and warning sound do not go off even when the passenger seat belt is fastened. ● Coolant leak from under the long life coolant reserve tank. ● Fuel cap strap broken. ● Door not opening / hard to open for both right side doors. ● Lumber switch inoperative. ● Right front seat cover stitch is tore out. ● Header seal deformation. This bulletin involves performing multiple inspections and repairs based on the listed Customer Symptoms.
104409
DOOR - PASSENGER AIR BAG
S258A000013
AM Radio Static, With No Active or Stored Radio Antenna Diagnostic Trouble Codes (DTC).
9100491 Rev 1
Drag Link Long Socket FOR STEERING SHIMMY DIAGNOSIS, PLEASE REFERENCE S1819000004 Rev. Q AND 19 - Steering / Diagnosis and Testing (IN SERVICE LIBRARY). PLEASE REFER 19 - Steering / Linkage / END, Tie Rod / Diagnosis and Testing IF YOU HAVE BALL JOINT LOOSENESS CONCERN. PLEASE DO NOT REPLACE DRAG LINK AND TIE ROD UNLESS PART HAS VISIABLE DAMAGE OR FREE PLAY EXCEEDS SPECS.
104558
FCA Caribbean Warranty Newsletter – Volume 11, Issue 4
104557
Warranty Newsletter – Volume 11, Issue 4
21-009-25 REV. B
850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2523000024
Rear Defogger Solder Terminals Detached.
S2408000015 REV.D
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
S2509000004
Misfire DTCs, Rough Idle, Valvetrain Noise
S2523000010 REV.A
Exterior Rear View Mirror Stained And Will Not Clean.
S2523000015 REV.A
Replacement Exterior Mirror Glass Connector Does Not Match For Blind Spot.
S2509000001 REV.A
Engine Rattle Noise
21-020-25 REV. A
Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P1DB7-00 - Torque Converter Clutch Performance. Customers may also experience one or more of the following: ● The check engine light illuminates. ● Overheating of the transmission fluid. This bulletin involves reprogramming the TCM with the latest available software.
9100534
Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback.
9100533
DCSD Before replacing this part for a Blank screen, screen flickering or screen inoperative concern, perform a hard reset to the Display and see if concern is resolved. Currently no dealer claims with this issue stating the RVC image is affected.
9100522
Ebooster When replacing the brake ebooster under warranty. Please return all associated parts which includes the snap rings so that the parts can be review by engineering.
21-026-25
Shifter Inoperative Customers may comment on the following: ● The vehicle can't be shifted out of Park or current selected gear. ● "Service Shifter, Stop Safely, Shut Off Engine To Engage Park" message displayed on the Instrument Panel Cluster (IPC). NOTE: Auto park will engage once the driver seat belt is unbuckled and the driver door is opened. REPAIR SUMMARY: This bulletin involves inspecting transmission shifter operation and possibly replacing the transmission shifter.
103773
TOP KIT - SOFT
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
08-067-25
Radio USB Update to U33.43 Customers may experience one or more of the following: ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally). Other software improvements included: ● Assist application performance improvements. REPAIR SUMMARY: This bulletin involves inspecting radio software level and if required, updating it with a USB to U33.43.
21-020-25
Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P1DB7-00- Torque Converter Clutch Performance. Customers may also experience one or more of the following: ● The check engine light illuminates. ● Overheating of the transmission fluid. REPAIR SUMMARY: This bulletin involves reprogramming the TCM with the latest available software.
103986
D-23-04 Rev. H 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
103987
ID-23-03 Rev. I 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
S2423000027 REV.C
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
18-011-25
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0420 - Catalyst System Efficiency Below Threshold Bank 1. ● P0017 - Crankshaft/camshaft Timing Misalignment - Bank 1 Sensor 2. ● P000A - Bank 1 Camshaft 1 Position Slow Response. ● P219A - Bank 1 Air-fuel Ratio Imbalance. Customers may also experience the following: ● A no crank/no start condition. In addition, the following software enhancement is available: ● Smart Charge change: Battery life improvements This bulletin involves possibly replacing the Oil control valves (OCV)s, and/or the Catalytic Converter and also reprogramming the PCM with the latest available software
103616
TAPPET KIT - FUEL DOOR
103777
TAPPET KIT - FUEL DOOR
103618
HOSE - COOLANT RECOVERY BOTTLE
S2509000002
Engine Noise
S258A000009
Apple CarPlay Does Not Complete The First Initial Wireless Connection.
18-008-25
Flash: Powertrain Control Module (PCM) Updates "Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other software enhancements included: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 heater crack improvements. ● OBD software changes. This bulletin involves reprogramming the PCM with the latest available software"
S2523000015
Replacement Exterior Mirror Glass Connector Does Not Match For Blind Spot.
9100498 REV 1
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
S2108000015 REV.J
Uconnect Box Require Service Message
9100500
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
S2523000010
Exterior Rear View Mirror Stained And Will Not Clean.
103292
MODULE - BATTERY HEATER
S2509000001
Engine Rattle Noise
09-003-25
Oil Leaking From Oil Filter Area Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: ● Oil found on the ground beneath the vehicle.
S1819000004 REV.Q
Shimmy Felt In Front End
08-033-25
Radio USB update to U33.43 Customers may experience one or more of the following: ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally). Other Software Improvements: ● Assist application performance improvements This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio’s current software level the radio may need a one or two USB update.
23-008-25
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S2323000004 REV.A
Defogger Is Not Working. Terminal Detached From The Glass.
23-007-25
Rear Defroster Inoperative Customers may experience one or more of the following: ● Rear window is not defrosting. ● The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window
S2008000084 REV.C
Cluster Warning Lamp is on, Service 4WD Message
S228A000005 REV.E
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
9100498
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets).
21-009-25 REV.A
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch
102934
THROTTLE BODY
102936
SHIFTER - TRANSMISSION
103062
SHIFTER - TRANSMISSION
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
102811
TRANSMISSION - 8 SPEED
102384
EVAPORATOR - AIR CONDITIONING
9100491
Drag Link Long Socket FOR STEERING SHIMMY DIAGNOSIS, PLEASE REFERENCE S1819000004 Rev. Q AND 19 - Steering / Diagnosis and Testing (IN SERVICE LIBRARY). PLEASE REFER 19 - Steering / Linkage / END, Tie Rod / Diagnosis and Testing IF YOU HAVE BALL JOINT LOOSENESS CONCERN. PLEASE DO NOT REPLACE DRAG LINK AND TIE ROD UNLESS PART HAS VISIABLE DAMAGE OR FREE PLAY EXCEEDS SPECS.
21-009-25
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
9100749 Rev 1
We have observed that some JL/JT rear axle shafts are leaking oil. Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.
08-004-25
Flash: Integrated Dual Charging Module (IDCM) Enhancements This bulletin involves reprogramming the IDCM with the latest software available. Customers may experience one or more of the following: ● Vehicle will not start and needs to be jump started as 12v battery drained. ● Vehicle will not charge
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
23-060-24
B-Pillar Water Leak When Vehicle Is Parked On A Hill Customers may experience one or more of the following: ● The vehicle will leak water from the top of the B-pillar when the vehicle is parked on a downward incline. ● Water on door trim or carpet. ● Water drips down the inside door and panel This bulletin includes performing a water test and possibly adding foam pads to both Freedom Panels.
9100468
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
101792
FILTER - AIR
101816
FILTER - AIR
9100363 Rev1
Turbocharger Kit Please note many parts of the Turbo Assembly can be serviced separately and complete turbo replacement may not be necessary. If the Turbo is being replaced for a noise or a rattle, inspect the wastegate for binding. The actuator kit is serviced separately. If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed oring for a leak. The o-ring is serviced separately
102365
Warranty Newsletter – Volume 10, Issue 11
102366
FCA Caribbean Warranty Newsletter – Volume 10, Issue 11
21-039-24 REV. H
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch
S248A000016
Customer complaints regarding rear view camera inoperative or flickering blue radio screen display while transmission is in reverse or blank screens when selecting the rear camera view following a recent service repair involving the removal and installation of the rear spare tire carrier
102300
Warranty Bulletin D-23-04 Rev. G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
102315
Warranty Bulletin ID-23-03 Rev. H 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
S2323000074 REV.A
Buzz Squeak Rattle (BSR) From Sound Bar Or Sport Bar Area.
S2423000050
Buzz Squeak Rattle (BSR) From Speaker Sound Bar At High Volume Level.
08-243-24
Radio USB update to U33.43 Customers may experience one or more of the following: ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally). This bulletin involves inspecting radio software level and if required, updating it with a USB to U33.43.
101684
COVER KIT - HOOD
101664
GRILLE - INSTRUMENT PANEL SPEAKER
101285
DAMPER - NONE
S2422000001 REV.C
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
9100433
Heated Steering Wheel Jl/JT Heating Steering Wheel INOP or not warm enough The purpose of this document is to help dealerships root cause or diagnose the issue of the heated steering wheel system. Before replacing or ordering replacement parts (steering wheel, switches and wire harness) because of Heated Steering Wheel Inoperative And Or Not Hot Enough concern please review Star On Line S2423000045 for further details
S2423000045
Heated Steering Wheel Inoperative And Or Not Hot Enough.
101232
Plate - Planetary
S2408000063 REV.B
Service Hybrid Electric Vehicle System Warning Message And Light Are Displayed. B273C-00 - Digital Crash Input Set In HCP
101137
Warranty Bulletin D-23-04 Rev. F 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
101140
FCA Caribbean Warranty Bulletin ID-23-03 Rev. G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
100774
SWITCH - HEADLAMP
S2408000110
Vehicle Does Not Start. Electric Steering Column Lock (ESCL) Does Not Function, Steering Wheel Locked. DTCs U1433-62, U1412-62, U1517-62 In The ESCL
100875
Warranty Bulletin D-23--04 2018 - 2024 (Current) Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
100876
FCA Caribbean Warranty Bulletin ID-23-03 Rev. F 2018 - 2024 (Current) Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
97802
SWITCH - HEADLAMP
S2405000001
Antilock Brake System (ABS) Module Will Not Initialize After Recent Service Replacement.
S2408000107
Dome Light Is Inoperative Or Remains On, B1751-11 Courtesy Lamp Control - Circuit Short To Ground Set In The BCM
03-009-24
Rear Axle Noise Customers may experience the following: ● An intermittent grinding, screeching, rubbing noise coming from the right hand side of vehicle on the rear axle. This bulletin involves cleaning and lubricating the axle shaft and hub splines.
S2408000106
Service SOS System Message Displayed on the Radio Display, Intermittent Microphone Cuts Out During Usage Attempts
100192
BOW - FOLDING TOP
S2422000002
Low Tire Pressure. Tire Valve Stem And Tire Pressure Monitor (TPM) Sensor Service.
08-203-24
Radio Over The Air Update from U29.44 to U33.43 Software Version (FOTA) Customers may experience one or more of the following: ● Unable to select the Turn by Turn Nav. ● Blank performance pages. Rearview Camera (RVC) functions normally. ● Android Auto® Voice Recognition (VR) inoperative. ● Media Tuner delayed. ● Charge schedule Human Machine Interface (HMI). RVC functions normally. ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation Map black. ● Offroad pages inoperative. RVC functions normally. ● VR inoperative. ● Incorrect song title displayed, Carplay® only. ● Human Unit (HU) switches from Media Page to Home Page. RVC functions normally. ● Ghost Touch on Navigation screen. RVC functions normally. ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the "Camera View Pages"". RVC functions normally. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from U29.44 to U33.43. NOTE: The national launch for the FOTA is expected to begin September 30, 2024.
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
18-050-24 REV. B
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● "Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other software enhancements included: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 heater crack improvements. ● OBD software changes. This bulletin involves reprogramming the PCM with the latest available software.
100209
Warranty Newsletter Volume 10 Issue 8_ID
100164
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
100203
WARRANTY OPERATIONS NEWSLETTER VOLUME 10, ISSUE 8
S2424000005
AC Is Inoperative
S2123000046 REV.B
Click Noise From Front End While Driving And Or Turning.
99670
GLOVE BOX - INSTRUMENT PANEL
99955
BEZEL - INSTRUMENT PANEL
S1819000004 REV.P
Shimmy Felt In Front End
99659
WHEEL - STEEL
S2408000087
Shifter Binding Or "Service Shifter" Message On The Cluster. DTSs U11C3, U1069, U0074, U114C
S2408000090
Passenger Mirror Inoperative
23-004-24 REV. A
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
99885
WARRANTY BULLETIN D-23-04 2018 - 2024 (Current) Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification (Rev. D)
99887
FCA Caribbean Warranty Bulletin ID-23-03 Rev. E adds 2024 model year vehicles and updates the Collision Service Bulletin number
S2403000003
Service 4WD Message Illuminated. Diagnostic Trouble Code (DTC) C2201-49 FDCM/FTCM Internal – Internal Electrical Failure, Set.
S2414000001 REV.A
Malfunction Indicator Lamp (MIL)-On/Check Engine Lamp (CEL)-On.
S2424000003
AC INOP With DTC B3A11 - AC REFRIGERANT EXPANSION VALVE ACTUATOR CONTROL PERFORMANCE
02-005-24 REV. B
Noise From Front End While Driving Customers may experience the following: ● Noise (rattle/thump/clunk noise) coming from the front end of the vehicle. This bulletin involves inspecting and possibly replacing the Active Stabilizer Bar System (ASBS).
18-065-24
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. This bulletin involves reprogramming the PCM with the latest available software and possibly replacing one or more oxygen sensors.
18-050-24 REV. A
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High.** ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● "Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other software enhancements included: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 Heater crack improvements. ● OBD Software changes. This bulletin involves reprogramming the PCM with the latest available software.
S2408000084
ABS Brake Lamp on Diagnostic Trouble Code (DTC) C0508-00 Right Front Wheel Speed Sensor Circuit Low
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
99500
CARRIER – PLANETARY & SHAFT KIT - OUTPUT
S2425000001
Malfunction Indicator Lamp/Check Engine Lamp On.
9100389
CAN Star Block Connector Customer finds MIL light on and technician finds DTC for loss of communication on one or more modules. In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.
03-007-24 REV. A
Rear Axle Noise Customers may experience the following: ● Intermittent grinding, screeching, ratcheting noise coming from the right hand side of vehicle on the rear axle. This bulletin involves cleaning and lubricating the axle shaft and hub splines."
03-007-24
Rear Axle Noise Customers may experience the following: ● Intermittent grinding, screeching, ratcheting noise coming from the right hand side of vehicle on the rear axle. This bulletin involves cleaning and lubricating the axle shaft and hub splines.
03-005-24 REV. A
Rear Axle Noise Customers may experience the following: ● Intermittent grinding, screeching, ratcheting noise coming from the right hand side of vehicle on the rear axle. This bulletin involves cleaning and lubricating the axle shaft and hub splines.
08-160-24
Management Procedure for Customer Issues in Connected Services Customers may experience the following: ● Various Connected Services issues. The purpose of this informative Technical Service Bulletin (TSB) is to support the Network on the following topics: ● Discern the different kinds of connected service issues (onboard / offboard). ● Support the customer in his journey to open a request via Customer Care. ● Address on the correct actions to properly manage a customer complaining about the received assistance.
9100363
Turbocharger Kit Please note many parts of the Turbo Assembly can be serviced separately and complete turbo replacement may not be necessary. If the Turbo is being replaced for a noise or a rattle, inspect the wastegate for binding. The actuator kit is serviced separately. If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed o-ring for a leak. The o-ring is serviced separately.
S2408000015 REV.C
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
9100362
MODULE Steering Control Before replacing the steering column control module (SCCM), please follow these steps: 1.- Make sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.
S2423000033
Water Leak From Front Door. Water On Front Floor.
S2414000001
Malfunction Indicator Lamp (MIL)-On/Check Engine Lamp (CEL)-On.
03-005-24
Rear Axle Noise Customers may experience the following: ● Intermittent grinding, screeching, ratcheting noise coming from the right hand side of vehicle on the rear axle. This bulletin involves cleaning and lubricating the axle shaft and hub splines.
08-149-24
12V Battery Low Level Charge Notification On Customer’s Mobile Application Vehicle's 12V battery Low Level Charge notification on customer’s mobile application.
98931
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
98933
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
08-144-24
Motor Generator Unit (MGU) Replacement Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: ● P1B0F-00 - Drive Motor A Position Sensor Offset Incorrect. Customers may experience one or more of the following: ● Vehicle goes into limp home mode. ● Vehicle does not start. This bulletin involves inspecting the MGU serial number and possibly replacing the MGU as needed.
9100360
SWITCH Power Window Before replacing the window switch, please follow these steps: 1.- Review the master window Switch for any physical issue (Button stuck, broke). If not, physical issue is found move to next step 2.- Make sure all the switches harness are properly connected, disconnect the switch and reconnect it, and reverify the issue. If after performing these steps the switch remains faulty, please replace the switch
08-142-24
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/system Voltage High (eTorque). Customers may also comment on the following: ● Customer finds Check Engine Light on and vehicle runs rough. This bulletin involves reprogramming the PCM with the latest available software.
94006
WIPERUNIT - WINDSHIELD WIPER, BLADE - FRONT WIPER
98861
WIPERUNIT - WINDSHIELD WIPER, BLADE - FRONT WIPER.
S228A000005 REV.D
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
23-043-24 REV. A
Popping Noise from Swing Gate Check Strap Customers may experience the following: ● A popping noise can be heard between the check strap and clevis pivot joint when fully opening the swing gate. This bulletin involves replacing the swing gate check strap. NOTE: Inspection is to be performed in the write up isle by a non-skilled employee or service adviser.
23-043-24
Popping Noise from Swing Gate Check Strap Customers may experience the following: ● A popping noise can be heard between the check strap and clevis pivot joint when fully opening the swing gate. This bulletin involves replacing the swing gate check strap. NOTE: Inspection is to be performed in the write up isle by a non-skilled employee or service adviser.
S2307000002 REV.B
Suspected Engine Coolant Leak
08-138-24
Global Telematics Box Module (TBM) Firmware Over The Air (FOTA) Software Update from 5.15 to 5.43 Customers may experience one or more of the following: ● Remote door lock and unlock commands sent from the Jeep mobile app fail. ● After saving the edited charge or climate schedule in the radio, the mobile app reverts it back to the schedule set on the Jeep mobile app. ● Remote operation ignition on remote start not working. ● Customer not receiving a monthly email containing the VHR (Vehicle Health Report). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 5.15 to 5.43. NOTE: National launch for this FOTA update is expected to begin June 14, 2024.
S1723000037 REV.A
Freedom Panel Underside Rough And Or White Coating Flaking
S2423000029
Water Leaking Near Front Bulkhead Or Cowl Area On Driver’s Side.
S248A000006
Radio Blank Screen or Cuts In and Out
18-050-24
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● "Service Transmission” message on due to Clutch Slip Detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other Software Enhancements: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 Heater crack improvements. ● OBD Software changes. This bulletin involves reprogramming the PCM with the latest available software.
9100338REV1
GENERATOR Engine Prior to alternator/generator removal: 1. Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section "System Operation - Smart Charging System". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC.
23-035-24
Right Front Door Lock Inoperable Customer may experience the following: ● Right front door lock does not actuate from switch. This bulletin involves inspecting the door lock operation and possibly reconnecting the switch harness connector
48B Combo
Customer Satisfaction Notification 48B Jack Kit Spacer
9100344
VALVE BODY & CONTROL UNIT Transmission Ensure clutch pressure check has been completed and documented prior to valve body replacement.
94519
HEADLAMP
S2307000002 REV.A
Suspected Engine Coolant Leak
S2208000063 REV.A
Loss Of Power Steering Assist. U0131 Lost Communication With Electro Hydraulic Power Steering Control Module (EHPS).
S2408000015 REV.B
Remote Keyless Entry (RKE) Button Functions Does Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed
9100337
PUMP WATER For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
0800324A
Horn Inoperative Customers or technicians may experience one ore more of the following: ? Horn is inoperative. ? Horn sound is very low. ? Horn is physically dissembling. This bulletin involves inspecting both horn date codes and replacing the horn(s) if needed.
9100245
Shield, Splash, Front Prior to replacing the LT splash shield (Part # 68469509AC) for a customer concern of tire rub on Jeep Wrangler PHEV Model only, please contact FCA REDACTED CONTENT. If no response in 15 minutes, go ahead with the repair.
9100287
Thermostat Assy For 2022-2024MY 3.6L Pentastar Upgrade with P0128 failure code. PRIOR TO PERFORMING ANY THERMOSTAT REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2309000014
0800624A
Navigation (NAV) Reboot When MOTA Fails The customer may describe one of more of the following: ? Radio navigation continues to reboot after a Map Update (MOTA). ? Navigation regularly cuts out and back on again. ? Radio switches to navigation without customer's input. This bulletin involves updating the Navigation maps via USB.
2300424
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S2408000002
Tire Pressure Warning Lamp is on Steady, or Flashing
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
Reference91A
Customer Satisfaction Notification 91A Incorrect Grille
0800324
Horn Inoperative Customers or technicians may experience one ore more of the following: ? Horn is inoperative. ? Horn sound is very low. ? Horn is physically dissembling. This bulletin involves inspecting both horn date codes and replacing the horn(s) if needed.
S2308000154
Rear Park Assist Warning Chime When Nothing is Behind the Vehicle
S238A000058
Radio Navigation Displays Message ?No Maps Available?
S2308000149
Key Fob Functions for Remote Start, Unlock and Lock Only Operate Near the Vehicle
0825023
Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0607-00 - ECU Internal Performance. ? P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. This bulletin involves updating the BPCM with the latest available software.
S2308000145
Remote Keyless Entry (RKE) And Remote Start Range Is Limited. B1A76-11 Remote Start Antenna Short To Ground Is Setting Erroneously
9100276
Spring Front Upr - Isolator Before replacing this part. Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.
2311023
Right Front Door Lock Inoperable Customer may experience the following: ? Right front door lock does not actuate from switch. This bulletin involves inspecting the door lock operation and possibly reconnecting the switch harness connector.
S2309000013
Verifying Camshaft Diagnosis
S238A000055
Audio Muted During A CarPlay Or Android Auto Phone Call
S2008000185
Uconnect 5 Voice Recognition Options
S2323000081
Buzz Squeak Rattle (BSR) From Rear Seat Area.
9100216
Body Control Module For concern related to DTC U0140 - Lost Communication with Body Control Module, please follow published diagnostic information for this DTC to ensure all module connections are secure. Please check all the connections at BCM from other modules that could potentially report a loss of communication with the BCM and ensure that they are fully seated as per diagnostic information. Some affected modules may include:Amplifier (AMP), IPC, HVAC,Radio, Digital TV, TPM, PCM, ORC, DTCM, SCCM, CVPM, EHPS, ICS, PTCM, OCM, PTS, PAM, DAS, DPDM, CSWM, ESM, ABS, PSSM, EAM, TBM, HCP, RF Hub, ASBS, LBSS, RBSS, AHLM, ITM, TCM. *Ensure to check all the wiring harness connected to BCM with Other Modules are proper. *Please disconnect the Battery Negative Cable for 15 minutes and then reconnect. *Clear the codes and check to see if any active DTC's return for U0140 *If still DTCs U0140 presents then contact Engineering Expert: FCA Redacted Content
9100244
FRT DOOR HINGE - DOOR CHECK If the front door check strap physically breaks or cracks, please call FCA Redacted Content. If no response in 15 minutes, proceed with repair. Please take pictures of the broken part and email the pictures to FCA Redacted Content.
S238A000049
SXM Lockup (rearview camera function is not affected), Cannot Change Channel or Adjust Volume
S1808000057
Inspecting And Disconnecting Negative Battery Cables On ESS Vehicles
9100220
Pan and Filter, Transmission Oil For WL & JL PHEV transmission leaks inspect for leaks through the transmission case prior to ordering a gasket. Leaks can be caused by possible porosity of transmission case or Oil Cooler Lines. Refer to the latest version of Star Online Publication S2321000005.
S238A000047
Humming Noise Through Speakers While Vehicle Is Off
S2318000010
Message in cluster for "Performance Limited Service Fuel System" with no DTC's
S2309000007
Customer complaint may include a noise from under the hood described as a ?belt-related? noise.
S238A000046
Maps Over The Air (MOTA) Is Causing The Navigation App To Continuously Reboot Or Map loading Screen Shown
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
S238A000044
Radio Display Blank Screen, Vertical Lines On The Display Or Radio Screen Freezing
S2323000075
2nd Row Center Seat Lazy Or Slow When Folding.
S2323000073
Exterior Mirror And Or Blind Spot Inoperative.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
S2323000074
Buzz Squeak Rattle (BSR) From Sound Bar Or Sport Bar Area.
S2321000005
Transmission Fluid Leak From Under The Vehicle.
S2323000072
Soft Top Windows Do Not Sit Flush To The Top.
S2319000007
Squeak Noise From Dash Area When Turning The Steering Wheel.
S2323000071
Front Door Window Will Not Roll Down All The Way. Window Stops Part Way Down.
9100212
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
S2308000113
Hybrid Control Processor (HCP) Sets B12B4-00 Charger Status Indicator Module Internal
9100209
Switch-Mirror Before replacing this Switch, please follow the service procedures to properly diagnose it 1) Remove the switch 2) Please check the continuity on each pin of the switch based on the table found in the service Procedures. If after testing switch is still faulty, please call FCA Redacted Content. If no response after 15 minutes, proceeds with switch replacement.
S2307000002
Suspected engine coolant leak.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100195
STARTER Engine Due to starter No Trouble Found claims, please contact FCA Redacted Content prior to repair. If no response in 15 minutes, proceed with repair.
2400623
A/C Diagnostic LOP Change
S1919000004
U0131-00-LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE ?A?. Service Electric Power Steering Message On Cluster.
S238A000043
SiriusXM (SXM) Advertisements Pop Up On Radio
0819623
Radio Internal Amplifier Calibration The customer may experience the following: ? Hissing/water sprinkler/salt shaker noise coming from front/rear speakers. Heard when radio ON and no media playing. Noise may be heard also when volume is turned down while music is playing or volume high with no music playing. The noise may become more prominent during phone calls on wireless. This bulletin involves re-calibrating the amplifier
S2323000059
Front Grille Is Not Correct For 2024 Willys Model JL.
S238A000039
SiriusXM (SXM) Not Subscribed
0819223
Flash: Instrument Panel Clusters (IPC) Updates
S2323000062
Oily Stain On Rear Seat Vinyl At The Seat Belt Buckle Locations.
9100185
ELECTRIC HYDRAULIC POWER STEERING PUMP Prior to replacing this component for damage at the pump electrical connection, please contact FCA redacted content. If no response in 15 minutes, proceed with repair.
S238A000030
Apple CarPlay Not Working Or Disconnecting After Updating To iOS 16.3.1 Or Above
91887
Warranty Bulletin D-20-13 STAR Center Uconnect 5 (R1) Radio Pre-Authorization Program ? Select Radios (New and Exchange) ?2023 Jeep Grand Cherokee (WL), 2023 Wagoneer and Grand Wagoneer (WS), 2023 Ram 1500 Pickup (DT), 2023 Ram Heavy Duty Pickup (DD/DF/DJ/DP/D2), 2024 Jeep Wrangler (JL) and 2024 Jeep Gladiator (JT) (Rev. F)
91890
FCA Caribbean Warranty Bulletin ID-22-11 STAR Center Uconnect 5 (R1) Radio Pre-Authorization Program ? Select Radios (New and Exchange) ?2023 Jeep Grand Cherokee (WL), 2023 Wagoneer and Grand Wagoneer (WS), 2023 Ram 1500 Pickup (DT), 2023 Ram Heavy Duty Pickup (DD/DF/DJ/ DP/D2), 2024 Jeep Wrangler (JL) and 2024 Jeep Gladiator (JT) (Rev. B)
S238A000032
Audio Distortion, Static Or Salt Shaker Noise Playing Through Speakers
S238A000031
Uconnect Box Require Service Message
0700723
Water Quality When Mixed With Engine Coolant
9100138
FILTER KIT, Transmission Oil For leak concerns that have been isolated to a transmission pan gasket, please replace ONLY the gasket. Pan/filter replacement are not required.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.