Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
23-043-26
Powertrain Control Module (PCM) Bracket Not Properly Secured Customers may comment on the following: SYMPTOM: ● Buzz, Squeak or Rattle (BSR) from the front of vehicle in the engine compartment. This bulletin involves inspecting and possibly remounting the PCM bracket.
S2609000011
MIL-On and/or Engine Oil Leak
9100904
Shifter If shifter is having trouble shifting between 1st and 2nd gear, then adjust cables as described in service library.
23-039-26
Steel Hood Vent Gap Customers may comment on one or more of the following: SYMPTOM: ● Gap between Steel Hood Vent and Performance Hood Fig. 1. ● Buzz, squeak and rattle noise. ● Hood pad water soaked after rain. ● Water leak through into the engine compartment. This bulletin involves Inspecting and possibly reseating the plastic hood vent.
9100900
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
OTHERDOC_177
Radio Over The Air Update to U43.17 R1H Software Version (FOTA) Customers may experience one or more of the following:- Navigation Stability - Android Auto & Carplay stability & connectivity- Distorted/glitchy display prior to start‑up animation- Text appearance display- Widget incorrect display- Turn signal blind spot response timing- Audio cut out - Drive Modes selection- Park assist Guidelines selction
23-036-26
Water Leak In Rear Cargo Area Customers may comment on the following: SYMPTOM: ● Water leak in the rear cargo area.
113835
COVER - CYLINDER HEAD
113792
PAD - INSTRUMENT PANEL
9100872
Display Exchange part has been superseded. Order the latest Z part number: Z8607669AC --> Z8791155AA (Active Exchange Part) Z8607669AD --> Z8791669AA (Active Exchange Part) Z8607669AE --> Z8791156AA (Active Exchange Part) Z8607671AC --> Z8791157AA (Active Exchange Part) Z8607671AD --> Z8791158AA (Active Exchange Part) Z8607671AE --> Z8791159AA (Active Exchange Part)
03-003-26
Rear Driveshaft Out Of Balance Customers may comment on one or more of the following: SYMPTOM: ● Vehicle exhibits a vibration that increases with speed that can be felt in the seat or floor. ● Oil is leaking from the Constant Velocity (CV) joint cover. This bulletin involves replacing the rear drive shaft.
56D Combo
Customer Satisfaction Notification 56D – Antilock Brake System Control Module Software - Dealer Notification
9100840
Switchbank 4 gang The customer will notice either one or two of the following conditions: 1. Fuel Door is Not opening when Fuel door Switch is pushed. Technician Observe the DTC P04CB-FUEL FILL DOOR OPEN REQUEST SENSOR-SWITCH CIRCUIT HIGH. 2. Drives Modes do not work when Switch is pressed (Hybrid, Electric, E-save). Technician Observe DTC U113B-LOST COMMUNICATION WITH SWITCH BANK MODULE. Procedure: If during vehicle Scan diagnostics besides DTC's P04CA, P04CB or U113B. there are another DTCs Repair it First accordingly. DTC's may be related to main ECU's like: HCP, BCM, PCM, etc. If DTC P04CB and/or U113B are still present, then follow the following action before replacing the Switch: 1. Read vehicle DTCs while the IGN ON. 2. Verify ESBM feed fuse state. Replace the fuse if needed. 3. Wiggle the ESBM harness takeout (LIN and ESBM feed takeout) and monitor the state of DTC P04CB and/or U113B. o If this step affects DTC P04CB and/or U113B. behavior, the issue is likely related to a failure in the harness. 4. Disconnect the harness from the ESBM and confirm there not any damage, like bend PINs, corrosion, etc. 5. Confirm Harness continuity. 6. Verify power to ESBM by back probing the ESBM connector o If voltage is lower than 11.8V, follow normal procedures for low batteries. - If there no damage in the harness nor the connector and pins of the ESBM, reconnect it ensuring the harness connector is being fully engaged into the ESBM connector. 7. Confirm Continuity of the harness from the ESBM connector to the BCM connectors. 8. Reconnect the ESBM and then Verify LIN bus activity with Mopar scope. o Config scope to LIN monitor if feasible. o Replace the ESBM only based confirmation from the LIN diagnostic. 9. With the scan tool, read DTCs. If still DTC are set, replace ESBM (Fuel door and drive modes Switch module) in accordance with the Service Information. Flag the part to be returned to supplier for further part analysis.
9100533 Rev 1
DCSD Before replacing this part for a Blank screen, screen flickering or screen inoperative concern, perform a hard reset to the Display and see if concern is resolved. Currently no dealer claims with this issue stating the RVC image is affected. Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only. Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only. Exchange Part Number Supersession For Ordering: 68607669AC --> Z8607669AC --> Z8791155AA 68607669AD --> Z8607669AD --> Z8791669AA 68607669AE --> Z8607669AE --> Z8791156AA 68607671AC --> Z8607671AC --> Z8791157AA 68607671AD --> Z8607671AD --> Z8791158AA 68607671AE --> Z8607671AE --> Z8791159AA
113240
SPARK PLUG - NONE
113241
SPARK PLUG - NONE
113270
CORE – HEATER
113271
CORE – HEATER
113291
ENCLOSURE - SPEAKER
9100833 REV1
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S2508000025 REV. B
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
23-024-26
Lower Left Door Pocket Contacting Customers may experience the following: SYMPTOM: ● Lower driver door outer trim flange edge contacting lower hinge surface. NOTE: The door trim edge is breaking through the hinge paint and E-coat. This bulletin involves inspecting the lower driver door outer trim flange for contact with the lower hinge surface, possibly modifying the trim edge of the door pocket and applying touch up paint.
113152
THERMOSTAT – NONE.
113153
THERMOSTAT – NONE.
112639
THROTTLE BODY – NONE
112640
THROTTLE BODY – NONE
S2508000025 REV.A
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
112862
MOTOR - BLOWER WITH WHEEL
112863
MOTOR - BLOWER WITH WHEEL
112842
BOLT - HEX FLANGE HEAD
112845
WIRING – INJECTOR
9100833
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S268A000014
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
112856
HEATER - ELECTRIC COOLANT
112857
HEATER - ELECTRIC COOLANT
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
111760
MOTOR AND LINKAGE - WINDSHIELD WIPER
08-114-26 REV. A
Flash: Driver Assistant System Module (DASM) Updates IMPORTANT! **This TSB CANNOT BE APPLIED unless BOTH of the following customer symptoms are met: 1. The customer recently had aftermarket tires installed or had a tire modification where the circumference of tire INCREASED and 2. A Malfunction Indicator Lamp (MIL) Illumination is present with DTC C2206-00 Vehicle Configuration Mismatch present and ACTIVE.** Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C2206-00 - Vehicle Configuration Mismatch. NOTE: DTC C2206-00 can trigger after a recent aftermarket tire installation or tire modification. This updated software is to address this DTC set by this condition. Customers may also experience one or more the following: ● Advanced Driver Assistance System features such as Adaptive Cruise Control (ACC), Advanced Emergency Braking (AEB) and Forward Collision Warning (FCW) are not available. ● "ACC/FCW Unavailable Service Required" message intermittently in the Instrument Panel Cluster (IPC). ● "Service Adaptive Cruise Control" message is displayed in the IPC. This bulletin involves inspecting and reprogramming of the DASM with the latest available software.
112203
SWITCH - STEERING WHEEL
112202
SWITCH - STEERING WHEEL
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
111833
SENSOR – KNOCK
111834
SENSOR – KNOCK
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
08-207-26
Instrument Panel Cluster (IPC) Flicker Turn By Turn The customer may experience flickering on their Instrument Panel Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay
S268A000013
Radio Volume Jumping Up To Max Volume After Radio Wake Up
111405
COVER - CYLINDER HEAD
111406
COVER - CYLINDER HEAD
S2623000018
Wind Noise From Hard Top Freedom Panels Near Rear View Mirror While Driving.
S268A000011
Radio Remains On After Ignition Off
08-133-26
Rear Defroster Inoperative Customers may experience one or more of the following: SYMPTOM: ● Rear window is not defrosting. ● The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window.
08-134-26
Universal Garage Door Opener (UGDO) Inoperable Technicians may or may not find the following Diagnostic Trouble Code (DTC) present: SYMPTOM: ● B251D1-00 - Universal Garage Door Opener Control. Customers may comment on the following: ● Operational questions regarding the usage of the HomeLink® UGDO. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
08-119-26
Flash: Comfort Seat Wheel Module (CSWM) Update Customers may experience the following: SYMPTOM: ● Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2623000013
Seat EZ Entry Inoperable Or Doesn’t Slide Forward.
08-114-26
Flash: Driver Assistant System Module (DASM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **C2206-00 - Vehicle Configuration Mismatch.** NOTE: **DTC C2206-00 can trigger after a recent aftermarket tire installation or tire modification. This updated software is to address this DTC set by this condition.** ● C2318-49 - Front Camera - Internal Electronic Failure. Customers may experience **one or more** the following: ● **"ACC/FCW Unavailable Service Required" message intermittently in the Instrument Panel Cluster (IPC).** ● "Service Adaptive Cruise Control" message in the Instrument Panel Cluster (IPC). ● Advanced Driver Assistance System features such as Adaptive Cruise Control (ACC), Advanced Emergency Braking (AEB) and Forward Collision Warning (FCW) not available. This bulletin involves inspecting and reprogramming of the DASM with the latest available software.
9100773
Disengaging Stabilizer Bar Front [SHG] 1. Follow procedure in SOL s2602000001 before replacing Smart Stabilizer Bar Assembly 2. If the ends of the stabilizer bar are rusted, DO NOT REPLACE THE STABILIZER BAR. The bar ends are currently masked to protect against excessive powder coats, which may lead to minor surface rust.
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2602000001
Service Electric Sway Bar Lamp On In Cluster. Diagnostic Trouble Code (DTC) C008E-00 In Auto Sway Bar (ASBS)
S2608000004
Remote Keyless Entry, Passive Entry, Remote Start Inoperative or a Cluster Message “Keyfob Not Detected”
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
23-005-26
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: SYMPTOM: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2610000002
2 nd Row Center Seatbelt Jammed Or Stuck. Webbing Twisted.
110405
GLOVE BOX - INSTRUMENT PANEL
110406
GLOVE BOX - INSTRUMENT PANEL
110626
PANEL - FRONT SEAT BACK
110399
HANDLE - INSIDE RELEASE
110400
HANDLE - INSIDE RELEASE
S2603000001
A suspected leak may be noticed on the front or rear axle pinion seal.
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
31-001-26 REV.A
Door Hem Aluminum Body Panel Corrosion Repair Customers may experience the following: SYMPTOM: ● Filifom corrosion at the hem area of the door. This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.
S228A000025 REV.A
Harman R1H Uconnect 5 Radio Software Flash Error Codes
110462
D-25-15 Rev. B Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
110469
ID-25-11 Rev. B Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles
S268A000008
Uconnect Box Requires Service, Please Visit an Authorized Dealer Message on Display Message With DTCs B1498-13, B1498-19 or B1570-93
110429
Warranty Newsletter – Volume 12, Issue 2
110431
FCA Caribbean Warranty Newsletter – Volume 12, Issue 2
S2423000027 REV.D
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
31-001-26
Door Hem Aluminum Body Panel Corrosion Repair Customers may experience the following: SYMPTOM: ● Filifom corrosion at the hem area of the door. This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.
9100591 Rev 1
Universal Garage Door Opener Prior to replacing the UGDO or sun visor, call HomeLink® Customer Care at 1-800-355-3515 for a proper evaluation of the issue. If this does not correct the issue, please follow the steps in SOL: S2508000039
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2408000024 REV.B
Power Top Switch Unresponsive, Full Retractable Sky Roof Does Not Open or Close
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
9100756
DO NOT REPLACE MULTIPLE SHOCKS UNLESS ALL ARE VERIFIED TO BE DEFECTIVE. Reference Master Tech article released in January 2026 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm
S2607000003
GMET4 DOHC Water Pump Coolant Leak Inspection
109607
CALIPER ASSEMBLY - DISC BRAKE
109986
SWITCH - LUMBAR CONTROL
S2607000002
Hemi Water Pump Coolant Leak Inspection
109820
SEAL - ROOF RAIL
109822
SEAL - ROOF RAIL
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
08-012-26
Speaker Diagnostic Procedure Rattle, buzz and squeak coming from specific speakers.
19-001-26
Tie Rod and Draglink Adjustment Clamp Fasteners Not Fully Secured Customers may comment on the following: ● Degrading steering alignment. This bulletin involves inspecting and possibly tightening tie rod and drag link adjustment clamp fasteners.
9100749
axle seal We have observed that some JL/JT rear axle shafts are leaking oil. Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.
109281
CENTER STACK – NONE
19-008-25
Tie Rod and Draglink Adjustment Clamp Fasteners Not Fully Secured Customers may comment on the following: ● Degrading steering alignment. This bulletin involves inspecting and possibly tightening tie rod and drag link adjustment clamp fasteners.
109227
DOOR - FUEL FILL
109228
DOOR - FUEL FILL
9100738 Rev 1
Issue Description: In JL/JT vehicles, many dealers and customers are not fully aware of the correct way to install the Mopar all-weather floor mats, especially the front mats. The all-weather mats are installed without removing the slit/perforation portion of the front carpet, which blocks the drain port on the all-weather mats completely and does not allow water/any liquid to get drained out of the vehicle through the drain hole on the underbody floor. Correct Installation Method for Mopar All-Weather Floor Mats 1. Find the slit/perforation on the front carpet (near the outboard mat post on the carpet )and cutout that piece from carpet. 2. Remove Drain Plug on the drain hole on the underbody floor 3. Install the All-Weather Mat. Make sure the mats built-in drain port lines up correctly into the drain hole on the floor. 4. Insert the drain plug in the drain port on all-weather mat to close the drain port. The plug is to be removed whenever there is need to drain water on the mat or to wash out dirt without removing the mat form the vehicle.
08-394-25 REV. A
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure.
S2523000096
CEL (Check Engine Lamp)/ Brake lamp Illuminated. Diagnostic Trouble Code (DTC) P083F- Clutch Pedal Position Sensor Performance.
9100734
If the DTC B1E21-96: Backup Battery-Component Internal Failure is active and customer states Popup message will show at the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347
9100736
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
9100738
Issue Description In JL/JT vehicles, the front carpets have a perforated section below the drain plug instead of a fully punched-out hole. This causes several problems: . Dealers often install all-weather mats without removing the carpet cutout, which completely blocks the drain. . Missing drain plug claims occur because the plug is not clearly visible. . Customers find it difficult to locate and access the drain plug, especially when the vehicle is muddy. Correct Installation Method for Mopar All-Weather Floor Mats To ensure proper drainage, follow these steps: 1. Identify the Issue: . Some owners place the all-weather mats directly over the carpet, blocking the drain hole even though the mat has a drain port. 2. Locate the Carpet Cutout: . Under the mat area, there is a pre-cut carpet section designed to be removed. 3. Remove the Carpet Piece and Plug: . Lift or cut out the small square of carpet to expose the metal floor. . Remove the rubber drain plug from the Jeeps floor. 4. Install the Floor Mat: . Place the all-weather mat back into position. . Align the mats built-in drain tube with the drain hole on the floor to form a proper seal. 5. Reinstall the Plug into the Mat: . Insert the drain plug (removed from the floor) into the drain hole on the mat. . This allows you to open the plug anytime to wash out dirt or water without removing the mats. Benefits . Enables washing the mats with a hose while they remain inside the vehicle; water drains directly to the ground instead of soaking the carpet. . Prevents water from getting trapped under the mat, avoiding carpet damage.
08-394-25
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present echnicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure
108893
MICROPHONE - AUDIO
S1819000004 REV.R
Shimmy Felt In Front End
108894
MICROPHONE - AUDIO
S258A000021
Diagnostic Trouble Code (DTC) B15A1-00 Media Port Connection 1 Connection Found Set.
108544
SWITCH - POWER WINDOW
108463
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108464
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108458
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
108461
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
9100723
1.Identify Customer Concern Check for small traces of coolant near the water pump, especially around the weeper chamber. Confirm if coolant is visibly dripping from the weeper chamber. 2.Root Cause identification The weeper chamber is designed to collect small amounts of coolant (< 3 ml/h) that pass through the dynamic seal. Red traces or shadows around the chamber may appear during initial operation due to seal adaptation or vapor condensation. These traces are not necessarily signs of a leak. Continuous dripping of coolant, however, indicates a malfunction. 3.Service Repair Procedure Lift the vehicle using an elevator. Verify if coolant is actively dripping from the weeper chamber. Run the engine at idle, alternating speed between 2000 4000 rpm for 15 minutes. Observe the weeper chamber during this test: If coolant continues to drip: Replace the water pump (possible permanent damage to the dynamic seal). If dripping stops: No further action is needed; the vehicle can be returned to the customer. 4.Clarify Leak Sources Do not confuse leaks from: The Press-In-Place rubber gasket (between water pump and engine block), or The inlet pipe nipples with leaks from the weeper chamber.
S2508000100
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S1805000006 REV.B
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
S2509000009
Engine Oil Leak
S2508000091
Radio (ETM) Is Always Setting Stored DTC B15A1-00 Media Port 1 Connection
105646
MODULE - STEERING CONTROL & COLUMN
08-331-25
Flash: Driver Assistant System Module (DASM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C2206-00 - Vehicle Configuration Mismatch. This bulletin involves inspecting and reprogramming of the DASM with the latest available software.
9100677
Power top /sky one touch switch falls out of the bezel or is pushed inside it or won't stay in place. Or if there's miscalibration in the power top. If the switch has no physical damage, is not broken or separated, but still doesn't stay in place, verify that the bezel brackets that hold it in place are broken and are the cause of the problem. If the bezel is broken, and the switch is not, replace only the bezel trim, DO NOT replace the switch. If there's miscalibration in the power top, and there's no physical damage to the switch and it works accordingly, DO NOT replace the switch.
9100670
Data collection required for all 2020-2026MY vehicles with 3.6L PSU engines during any of their first 3 engine oil changes. This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.
S2218000003 REV.B
Customer complaint may include a Mil On/Check Engine Lamp On and Electronic Throttle Control (ETC) Lamp On. There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:
107418
SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
9100649
False fails on PCR, DBSM and PDCs Stuck Closed or open diagnostics, DTC P2AF5 or P2AF6, leading to NTF and unnecessary replacements. Current controls are not robust against depleted auxiliary battery condition. Please follow SOL S2508000031.
105648
MODULE - ENGINE CONTROLLER
105288
VALVE - CHECK
105647
RAIL - REAR
9100605
Shim - felt GIM # NUSENGCHR24018991: JL JT sun visor center support BSR. Add felt shim 68736674AA - 43MM OD x 10mm ID x 1mm thick.
9100749 Rev 1
We have observed that some JL/JT rear axle shafts are leaking oil. Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.