Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
CS2312_TSB_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
SC340_TSB_R5
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS: ECM LOGIC IMPROVEMENT (SC340 REVISION 5) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2020MY Optima, 2016-2020MY Sorento, 2017-2022MY Sportage vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
SC340_OWNR_NQ5_105
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: OWNER NOTIFICATION (SC340 FLIGHT 105) - This document is the owner notification advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) for certain 2017-2022 MY Sportage vehicles equipped with 2.4L Gas Direct Injection (GDI) engines to ensure compliance with emissions regulations.
SC340_TSB_R4
Emissions
TECHNICAL SERVICE BULLETIN: VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSION SECM LOGIC IMPROVEMENT (SC340 REV 4) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
TSB_CS2312_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
SC340_OWNR_QL103
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: OWNER NOTIFICATION (SC340 FLIGHT 103 / QL) - This document is the owner notification advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) for certain 2017-2022 MY Sportage vehicles equipped with 2.4L Gas Direct Injection (GDI) engines to ensure compliance with emissions regulations.
TSB_CS2312
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
CS2312_OWNR
Other
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION (CS2312) - This document is the owner notification advising that Kia is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installed—if requested—at no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)
SC340_TSB_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS ECM LOGIC IMPROVEMENT (SC340) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
PS797
Other
PITSTOP: TECHNICAL OPERATIONS: EXTERNAL DAMAGE TO ULTRASONIC SENSOR: This Pitstop provides information related to Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a “Warning Lamp’ to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)
SC340_OWNR_QL101
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: OWNER NOTIFICATION (SC340 FLIGHT 101 / QL) - This document is the owner notification advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) for certain 2017-2022 MY Sportage vehicles equipped with 2.4L Gas Direct Injection (GDI) engines to ensure compliance with emissions regulations.
SC340_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: VOLUNTARY SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS ECM LOGIC IMPROVEMENT (SC340) - This bulletin has been revised to include additional information. New / revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
SC340_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS ECM LOGIC IMPROVEMENT (SC340) - This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
SC340_DP
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: DEALER PRINCIPAL MEMO (SC340) - This document is the announcement to the dealer principals advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations in certain 2017-2022 MY Sportage vehicles manufactured from December 10, 2015, through December 7, 2021, certain 2016-2020 MY Optima vehicles manufactured from August 28, 2015, through June 23, 2020, and certain 2016-2020 MY Sorento vehicles manufactured from October 27, 2014, through November 4, 2020, equipped with 2.4L Theta GDI engines.
SC340_DPSM
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: DEALER PARTS AND SERVICE MANAGER MEMO (SC340) - This document is the announcement to the dealer Parts and Service managers advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations in certain 2017-2022 MY Sportage vehicles manufactured from December 10, 2015, through December 7, 2021, certain 2016-2020 MY Optima vehicles manufactured from August 28, 2015, through June 23, 2020, and certain 2016-2020 MY Sorento vehicles manufactured from October 27, 2014, through November 4, 2020, equipped with 2.4L Theta GDI engines.
SC340_POC
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: SC340_POC: PROOF OF CORRECTION CARD
SC340_QA
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: QUESTION AND ANSWER (SC340) - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Voluntary Emissions Service Campaign SC340.
SC340_STKR
Emissions
SC340_STKR: VOLUNTARY EMISSIONS SERVICE CAMPAIGN COMPLETION LABEL/STICKER
TSB_TRA046_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.
TSB_ENG222_R8
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ENG222_R7
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
CS2302_TSB_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGREADE $ DECAL INSTALLATION (CS2302) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from December 10, 2015 through December 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.
TSB_TRA046_R4
Service Bulletin/Repair Instructions
This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced.
PI1802YZ_TSB_R7
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement"; equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
PS750
Service Bulletin/Repair Instructions
PITSTOP: AWD SYSTEM CONCERN DUE TO TIRE CIRCUMFERENCE - This Pitstop provides information regarding potential concerns with the All-Wheel-Drive (AWD) system due to tire sizes of differing circumference. Some customers may complain of a chatter sensation felt in the drivetrain of the vehicle and/or the failure of drivetrain component(s). A difference in tire size (width, aspect ratio, construction, rim diameter etc.) may be the cause.
CS2310_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: KIA GENUINE REMOTE START CONTROL MODULE UPGRADE FOR ANTI-THEFT LOGIC COMPATIBILITY (CS2310) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 7. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.
CS2302B_OWNR2
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER RE-NOTIFICATION - This document is the owner re-notification advising that Kia has developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.
CS2302_TSB_R4
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2302) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
CS2310_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN CUSTOMER SATISFACTION: KIA GENUINE REMOTE START CONTROL MODULE UPGRADE FOR ANTI-THEFT LOGIC COMPATIBILITY (CS2310) - This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 6. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.
PS610_R1
Service Bulletin/Repair Instructions
PITSTOP: SRS DTC B176200 AND/OR B168400 - This pitstop has been revised to include additional information. New/revised sections of this pitstop are indicated by a black bar in the margin area. This Pitstop provides information regarding a possible mismatch of a SRSCM (Supplemental Restraint System Control Module) and driver seat belt buckle that may set the SRS DTC(s) B168400 and/or B176200 on the models listed below. When diagnosing a vehicle that has been in an accident and/or has recently had a superseded SRSCM replaced, it may be necessary to inspect and replace the driver seat belt buckle with the latest production P/N listed in EPC. Older production driver seat belt buckles have a 4 pin connector and may no longer be compatible with the superseded SRSCM. Only the SRSCM is superseded; the driver seat belt buckle is not superseded.
CS2302_TSB_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2302) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
CS2302_TSB_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2302) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.
CS2302B_OWNR
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia has developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.
CS2302_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2302) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.
CS2302A_OWNR
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia has developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.
CS2302_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2302) - This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.
TSB_TRA046_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.
TSB_ENG219_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: MAINTENANCE REMINDER FEATURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.
TSB_SST067_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: BEARING CLEARANCE TESTER (BCT) PROCEDURES - This bulletin provides information regarding test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.
PS720
Service Bulletin/Repair Instructions
PITSTOP: INJECTOR HARNESS ROUTING FOR PI1802Y/Z AND PI1803Y/Z ENGINE REPLACEMENTS - This bulletin provides information to address a no-start or hard start with poor running condition after engine replacement under PI1802Y/Z or PI1803Y/Z. Some replacement long blocks may come with pre-installed fuel rail, injectors, and injector wiring harness. If the condition is present, it is possible that the injector harness was not installed correctly. The connections may be swapped from cylinder No. 1 and cylinder No. 4, and from cylinder No. 2 and cylinder No. 3.
TSB_BOD306
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PANORAMIC SUNROOF INOPERATIVE AND/OR ABNORMAL NOISE WHEN OPERATING - This bulletin provides information to improve the operation of the panoramic sunroof on some 2017-2022MY Sportage (QL) vehicles, produced from December 10, 2015 through December 7, 2021, which may exhibit slow, noisy, or inoperative sunroof operation caused by dust or dirt intrusion into the sunroof track mechanism. Vehicles driven in dusty environments with a high concentration of sand or dirt in the air, may accumulate debris into the sunroof mechanism causing friction.
TSB_ENG222_R6
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ENG222_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
PI1802YZ_TSB_R6
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
TSB_ENG222_R4
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ELE231_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: FRONT VIEW CAMERA REPLACEMENT FOR DTC C160449 & C160649 - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on the inspection and replacement of the front camera on some vehicles. Due to an internal control chip concern inside the camera, the vehicle may exhibit a Forward Collision Avoidance Assist Warning Lamp (A) and/or Master Warning Lamp (B) with C160449 and/or C160649 codes. Certain systems may become temporarily disabled during occurrences: Smart Cruise Control (SCC), Lane Keep Assistance (LKA), Lane Departure Warning (LDW), Forward Collision-Avoidance Assist (FCA), Forward Collision Warning (FCW) and/or Driver Attention Warning (DAW).
PI1802YZ_TSB_R5
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
TSB_SST067_R1
Service Bulletin/Repair Instructions
This bulletin provides information regarding test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.
TSB_CHA084_R8
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.
TSB_BOD055_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: INFORMATION FOR HEADLAMP CONDENSATION AND MOISTURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.
TSB_ENG222_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ELE231_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: FRONT VIEW CAMERA REPLACEMENT FOR DTC C160449 & C160649 - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on the inspection and replacement of the front camera on some vehicles. Due to an internal control chip concern inside the camera, the vehicle may exhibit a Forward Collision Avoidance Assist Warning Lamp (A) and/or Master Warning Lamp (B) with C160449 and/or C160649 codes. Certain systems may become temporarily disabled during occurrences: Smart Cruise Control (SCC), Lane Keep Assistance (LKA), Lane Departure Warning (LDW), Forward Collision-Avoidance Assist (FCA), Forward Collision Warning (FCW) and/or Driver Attention Warning (DAW).
PS704
Service Bulletin/Repair Instructions
PITSTOP: FRONT RADAR SENSOR MOUNTING INSPECTION (PS704) - This pitstop provides information regarding front radar sensor alignment on 2014MY and later vehicles that may exhibit a warning light ON related to radar sensor alignment errors in the Forward Collision-Avoidance Assist (FCA)/Smart Cruise Control (SCC) system.
TSB_ELE231_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: FRONT VIEW CAMERA REPLACEMENT FOR DTC C160449 & C160649 - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on the inspection and replacement of the front camera on some vehicles listed below. Due to an internal control chip concern inside the camera, the vehicle may exhibit an MIL on with DTC C160449 and/or C160649.
TSB_CHA084_R7
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
TSB_ENG222_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ENG222_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.
TSB_CHA084_R6
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
PI1802YZ_TSB_R4
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled âÂÂKnock Sensor Detection System - ECU Logic Improvementâ equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
TSB_CHA084_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
PS663
Service Bulletin/Repair Instructions
PITSTOP: MFC, CONCERNS FOR DISABLED OPERATION - This Pitstop provides information regarding concerns with disabled operation of Multi-Function Camera (MFC) on some Kia vehicles. When normal operation is not possible due to certain outside environment conditions (such as sunlight glare, heavy rain, sunlight, snow, fog and/or substance/debris) causing a temporary concern. This stops operation causing Warning Lamp ON and/or Pop-up Message displayed on the cluster. This is a normal operation of the ADAS and once environment conditions improve and/or substance/debris are removed, the system will clear itself and operate normally.
PS675
Service Bulletin/Repair Instructions
PITSTOP - BRAKE CALIPER LEAK INSPECTION - This PITSTOP provides information related to a brake caliper fluid/oil substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.
PI1802_TSB_R12
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT - TSB_PI1802_R2 - Knock Sensor Detection System - ECU Logic Improvement - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
TSB_ENG219
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: MAINTENANCE REMINDER FEATURE - This bulletin provides information on setting the "Service Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.
PI1802YZ_TSB_R3
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN - ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z_Rev3) - This bulletin has been revised to include additional information. - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".
PI1802YZ_TSB_R2
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN - ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z_Rev2) - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".
PI1802_TSB_R11
Service Bulletin/Repair Instructions
TSB: PRODUCT IMPROVEMENT CAMPAIGN : KNOCK SENSOR DETECTION SYSTEM (KSDS) LOGIC IMPROVEMENT (PI1802_R11) - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
PS608_R1
Service Bulletin/Repair Instructions
PITSTOP: UPDATED SPARK PLUG FOR 2.0T THETA-II - This bulletin has been revised to include additional information. This Pitstop provides information regarding the updated spark plug for vehicles listed below, equipped with 2.0T Theta-II engines, which may not yet be available in the Electronic Parts Catalog (EPC). If not available, the updated spark plug must be ordered manually. This updated spark plug has been improved with the thread shoulder lengthened to enhance protection of the insulator from combustion heat.
TSB_ENG205_C
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: SERVICE ACTION: WIRING SIGNAL INTERFERENCE CHECK & ENGINE NOISE INSPECTION (SA379) - CLOSED - SUPERSEDED BY PI1802YZ/1803YZ.
PI1802YZ_TSB_R1
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
PI1802WX_TSB_R7C
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: TSB_R7 - ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - CLOSED - SUPERSEDED BY PI1802Y/Z.
PI1802YZ_TSB
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: TSB - ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
PI1802_TSB_R10
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: TSB - REV 10 - KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
PI1802_TSB_R9
Service Bulletin/Repair Instructions
TSB - PRODUCT IMPROVEMENT CAMPAIGN - KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) Rev.9 - This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
TSB_ELE148
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: HALOGEN HEAD LAMP LOW BEAM BULB CONNECTOR REPLACEMENT - This bulletin provides information regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.
PI1802WX_TSB_R7
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - This bulletin has been revised to include additional information.This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC), P1326.
PI1802_OWN#3_SPG
Service Bulletin/Repair Instructions
Owner Letter - PRODUCT IMPROVEMENT CAMPAIGN (PI1802) **THIRD NOTICE** - Dear Kia Sportage Owner: Kia Motors America, Inc. is conducting an important Product Improvement Campaign to perform a software update on all 2014-2018 MY Sportage vehicles equipped with 2.4L Gasoline Direct Injection ("GDI") and 2.0L Turbocharged GDI ("T-GDI") engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").
TSBCHA084_R4
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.
TSBTRA086
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN - PARTIAL REPAIR OF 4WD COUPLING - This bulletin provides the procedure information regarding the partial repair of the Four Wheel Drive (4WD) Coupling Assembly, Pressure Sensor, Actuator Motor or 4WD harness on some 2011-2020 Sportage (SL, QL) and 2013-2020MY Sorento (XMa, UMa) 4WD vehicles for a concern regarding: ï· Oil leakage from the 4WD coupling assembly ï· 4WD Malfunction and MIL lamp ON with DTCs ï· Abnormal noise or vibration while driving
PI1802WX_TSB_R6
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN PI1802W/X (Rev 6) - PRODUCT IMPROVEMENT CAMPAIGN - ENGINE REPLACEMENT INSTRUCTIONS - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled 'Â"Knock Sensor Detection System - ECU Logic Improvement"ÂÂ. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("ÂÂDTC"ÂÂ), P1326.
PI1802_TSB_R8
Service Bulletin/Repair Instructions
TSB - Product Improvement Campaign: KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
TSBCHA084_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN TSB084_R3: PARTIAL REPAIR OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
PI1802_TSB_R7
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN - KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) - This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage. The KSDS detects vibrations indicating the onset of excessive connecting rod bearing wear. It is designed to alert the driver at an early stage of bearing wear before the occurrence of severe engine damage, including engine failure. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Limp Home Mode. This will reduce further damage to the engine and ensure that the vehicle occupants are not exposed to the risk of a more severe engine failure. At that time, Diagnostic Trouble Code (âÂÂDTCâÂÂ) P1326, specific to the KSDS, will be recorded in the ECU. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed. Also, engine RPMs will be limited to approximately 1800-2000 RPM.
TSBCLI046_R1
Service Bulletin/Repair Instructions
TSBCLI046_R1: REDUCED PERFORMANCE OR INOPERATIVE AIR CONDITIONING - This bulletin has been revised to include additional information. This bulletin provides the procedure to inspect the Air Conditioner (A/C) and replace the A/C compressor, Evaporator Temperature Sensor (ETS), and/or External Control Valve (ECV), depending on the inspection results on some 2017-2019MY Sportage (QL) vehicles, produced from December 1, 2015 through July 7, 2017, which may exhibit intermittent poor air conditioning performance.
TSBCLI046
Service Bulletin/Repair Instructions
TSB: REDUCED PERFORMANCE OR INOPERATIVE AIR CONDITIONING - This bulletin provides the procedure to inspect the Air Conditioner (A/C) and replace the A/C compressor, Evaporator Temperature Sensor (ETS), and/or External Control Valve (ECV), depending on the inspection results on some 2017-2019MY Sportage (QL) vehicles, produced from December 1, 2015 through July 7, 2017, which may exhibit intermittent poor air conditioning performance.
TSBENG178_R3
Service Bulletin/Repair Instructions
TSB: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC18) - This bulletin has been revised to include additional information. This bulletin provides information related to extracting âÂÂin use performance trackingâ emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.
PS610
Service Bulletin/Repair Instructions
PITSTOP: SRS DTC B176200 AND/OR B168400- This Pitstop provides information regarding a possible mismatch of a SRSCM (Supplemental Restraint System Control Module) and driver seat belt buckle that may set the SRS DTC(s) B168400 and/or B176200 on the models listed below. When diagnosing a vehicle that has been in an accident and/or has recently had a superseded SRSCM replaced, it may be necessary to inspect and replace the driver seat belt buckle with the latest production P/N listed in EPC. Older production driver seat belt buckles have a 4 pin connector and may no longer be compatible with the superseded SRSCM. Only the SRSCM is superseded; the driver seat belt buckle is not superseded. DTC B176200:
PI1802_OWNR2_SPO
Service Bulletin/Repair Instructions
PI1802_OWNR2_SPO: Kia Motors America, Inc. is conducting an important Product Improvement Campaign to perform a software update on all 2014-2018 MY Sportage vehicles equipped with 2.4L Gasoline Direct Injection ("ÂÂGDI"ÂÂ) and 2.0L Turbocharged GDI ("ÂÂT-GDI"ÂÂ) engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ÂÂECU"ÂÂ).
PS608
Service Bulletin/Repair Instructions
PITSTOP: UPDATED SPARK PLUG FOR 2.0T THETA-II - This Pitstop provides information regarding the updated spark plug for 2017-2018MY Sportage (QL) 2.0T and 2016-2018MY Sorento (UMa) 2.0T vehicles, which may not yet be available in the Electronic Parts Catalog (EPC). If not available, the updated spark plug must be ordered manually.
TSBENG178_R2
Service Bulletin/Repair Instructions
TSB: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC18) - This bulletin provides information related to extracting "in use performance tracking" emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.
PI1802WX_TSB_R5
Service Bulletin/Repair Instructions
TSB: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.
TSBENG205_R1
Service Bulletin/Repair Instructions
TSB: SERVICE ACTION: WIRING SIGNAL INTERFERENCE CHECK & ENGINE NOISE INSPECTION (SA379) - This bulletin provides information related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.
TSBENG205
Service Bulletin/Repair Instructions
TSB: SERVICE ACTION: WIRING SIGNAL INTERFERENCE CHECK & ENGINE NOISE INSPECTION (SA379) - This bulletin provides information related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.
TSBTRA076
Service Bulletin/Repair Instructions
TSB: 2.4GDI TCU LOGIC IMPROVEMENT FOR SHIFT FLARE - This bulletin provides the procedure to improve the logic of the Transmission Control Unit (TCU) on some 2017-2018MY Sportage (QL) 2.4L vehicles, produced from December 10, 2015 through April 5, 2018, which may experience an intermittent shift flare concern.
PI1802WX_TSB_R4
Service Bulletin/Repair Instructions
TSB: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.
PS590
Service Bulletin/Repair Instructions
PITSTOP: BLOCKED WINDSHIELD WASHER NOZZLES ON VEHICLES EQUIPPED WITH WASHER HEATERS - This Pitstop provides information regarding blocked windshield wiper nozzles on some 2016MY~ Sorento (UMa) and 2017MY~ Sportage (QL) vehicles equipped with windshield washer heaters (A). Mixing tap water (?) and concentrated windshield washer fluid can cause corrosion of the heater element due to the mineral content of tap water.
VPI1802WX_TSB_R3
Service Bulletin/Repair Instructions
VEHICLE PRODUCT IMPROVEMENT: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X)- This bulletin has been revised to include additional information This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326..
VPI1802_TSB_R6
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN:KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) - This bulletin has been revised to include additional information.This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
VPI1802WX_TSB_R2
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 5, 12/20/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.
DC_20190125
Service Bulletin/Repair Instructions
RECENT KIA MEDIA REPORTS, January 25, 2019 Update - Dear Kia Retailer, At Kia, safety is a top priority and we wrote to you last August and again last October to provide you with updates regarding news reports about non-collision fires in Kia vehicles and the status of Kia?s cooperative work with NHTSA.
TSBENG083_R1
Service Bulletin/Repair Instructions
TSB: SPECIAL SERVICE INFORMATION & SPECIFICATIONS FOR GDI HIGH PRESSURE FUEL SYSTEM - This bulletin has been revised to include additional information. This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.
VPI1802_TSB_R5
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
TSBCLI041_CLOSED
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: EVAPORATOR TEMPERATURE SENSOR AND/OR ECV REPLACEMENT (SA309) This bulletin has been closed.
PS532_R1
Service Bulletin/Repair Instructions
PITSTOP - DTC P0449 VENT VALVE/SOLENOID CIRCUIT & P2422 VENT VALVE STUCK CLOSED - This bulletin has been revised - When addressing a concern related to P0449 (Evaporative Emission System ? Vent Valve / Solenoid Circuit) or P2422 (Evaporative Emission System Vent Valve Stuck Closed) on 2017MY~ Sportage (QL) model vehicles, and the Canister Closed Valve (CCV) and corresponding circuit were found to be within specifications, it may be necessary to inspect for flow restrictions within the EVAP ventilation system. If a foreign object is found anywhere from the filler neck to the main charcoal canister, such as a spider nest (A), the object will need to be removed with a pipe cleaner. Trying to clear the hose with compressed air has proven to be ineffective and should not be done. The most common area of spider nest presence is located at the filler neck. Fuel Tank
VPI1802_OWNER_SP
Service Bulletin/Repair Instructions
Dear Kia Sportage Owner: Kia Motors America, Inc. is conducting an important Product Improvement Campaign to perform a software update on all 2016-2018 MY Sportage vehicles equipped with 2.4L Gasoline Direct Injection (?GDI?) and 2.0L Turbocharged GDI (?T-GDI?) engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (?ECU?).
PS578
Service Bulletin/Repair Instructions
PITSTOP: IDENTIFYING A SEIZED COMPRESSOR - This Pitstop provides information regarding the diagnosis of an A/C related concern on 2017-2019MY Sportage (QL) and 2015-2018MY K900 (KH) vehicles that may have a seized compressor. To confirm the diagnosis of a seized A/C compressor, visually inspect for a paint mark (A) against the limiter in the center of the compressor. If the mark is no longer aligned (B), an internal disconnection of the limiter has occurred and the compressor assembly needs to be replaced.
VPI1802_QA
Service Bulletin/Repair Instructions
Q & A - This document is the Q & A for the new Product Improvement Campaign to provide information regarding a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.
VPI1802_DP
Service Bulletin/Repair Instructions
DEALER PRINCIPAL NOTICE - This notice advised the dealer principal of the new Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.
VPI1802_DSM
Service Bulletin/Repair Instructions
DEALER SERVICE MANAGER NOTICE - This notice advised the dealer service manager of the new Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.
PS569
Service Bulletin/Repair Instructions
PITSTOP - INAUDIBLE TURN SIGNALS AND NO SEAT BELT AND KEY WARNING CHIME - This Pitstop provides information regarding an inoperative cluster speaker on 2017-2018MY Sportage (QL). Customer concern may include inaudible turn signals and no seat belt and key/key fob warning chimes.
PS451_R2
Service Bulletin/Repair Instructions
PITSTOP - FRONT LICENSE PLATE AND MOUNTING BRACKET POSITION ON VEHICLES EQUIPPED WITH AEB/FCA - This bulletin has been revised to include additional information. This Pitstop provides information regarding the installation of the front license plate bracket on 2017MY~ Sportage (QL) and 2019MY~ Sorento (UMa) vehicles equipped with Autonomous Emergency Braking (AEB) / Forward Collision Avoidance Assist (FCA).
PS564
Service Bulletin/Repair Instructions
PITSTOP - CLOCK CONCERNS ON UVO eSERVICES (UVO 3.0) - This Pitstop contains information regarding possible concerns with the clock on UVO eServices (UVO 3.0) head units installed on 2017-2018MY vehicles.
TSBENG178_R1
Service Bulletin/Repair Instructions
TSB - DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC18) - This bulletin has been revised to include additional information. This bulletin provides information related to extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.
PS551
Service Bulletin/Repair Instructions
PITSTOP - RATTLE NOISE FROM REAR OF THE VEHICLE (PS551) - This Pitstop contains information regarding a rattle type noise heard from the rear of the vehicle when closing a door or trunk on some 2016MY-2018MY vehicles.
PS539
Service Bulletin/Repair Instructions
PITSTOP - ENGINE COMPONENT RE-USE GUIDELINES - In general, parts and components removed during engine repairs should be considered serviceable, and should be thoroughly cleaned and transferred to the new engine.
PS546
Service Bulletin/Repair Instructions
PITSTOP - ELECTRONIC STABILITY CONTROL SELF-CHECK NOISE - This Pitstop provides information regarding a concern related to a single faint ?thud? type noise heard from the engine compartment at speeds of 18-20 MPH after initial start-up. Be aware that the Electronic Stability Control (ESC) system performs it?s self-check under these conditions. This single faint ?thud? type noise is normal and indicates that the ESC is functioning properly.
TSBTRA047_R2
Service Bulletin/Repair Instructions
TSB - DRIVESHAFT SERVICEABILITY - This bulletin has been revised most recently to include additional information. This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.
VSCSC161OWNER
Service Bulletin/Repair Instructions
SC161 - OWNER LETTER - Owner Notification Letter advising of the Voluntary Service Campaign to upgrade the ECM software to improve the Instrument Cluster Logic.
TSBENG180_R1
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L ENGINE START LOGIC IMPROVEMENT (SA320) - This bulletin has been revised to include additional information. This bulletin provides the procedure to improve the logic of the Electronic Control Unit (ECU) on some 2018MY Sportage (QL) vehicles, produced from April 3, 2017 to August 9, 2017, which may intermittently experience an extended cranking condition.
TSBENG178
Service Bulletin/Repair Instructions
TSB - DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC18) - This bulletin provides information related to extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.
VSCSC161DP
Service Bulletin/Repair Instructions
SC161 - DEALER PRINCIPAL LETTER - Advises dealer principal of the new service campaign to upgrade the ECM software to improve the Instrument Cluster Logic.
VSCSC161DSM
Service Bulletin/Repair Instructions
SC161 - DEALER SERVICE MANAGER LETTER - Advises dealer principal of the new service campaign to upgrade the ECM software to improve the Instrument Cluster Logic.
VSCSC161QA
Service Bulletin/Repair Instructions
SC161 - QA - This document contains frequently asked questions and answers regarding the Service Campaign to upgrade the ECM software to improve the Instrument Cluster Logic.
VSCSC161TSB
Service Bulletin/Repair Instructions
SC161 - TECHNICAL SERVICE BULLETIN (TSB) - This publication contains the repair procedures for the campaign.
PS500_R1
Service Bulletin/Repair Instructions
PITSTOP - PREMIUM NAVIGATION OR UVO eco WITH NAVIGATION (AVN 5.0) - This Pitstop provides information regarding the features and functionality on the latest generation Premium Navigation or UVO eco with Navigation (designated as AVN 5.0) system that is applied to some 2018MY Sportage (QL), Optima (JFa), Soul (PS), Stinger (CK), and Niro PHEV (DE) vehicles. This system features a dual core processor which should result in a faster system response and loading performance between applications as compared to the previous navigation system.
TSBENG180
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L ENGINE START LOGIC IMPROVEMENT (SA320) -
PS532
Service Bulletin/Repair Instructions
PITSTOP - DTC P0449 VENT VALVE/SOLENOID CIRCUIT - When addressing a concern related to P0449 (Evaporative Emission System - Vent Valve / Solenoid Circuit) on 2017-2018MY Sportage (QL) model vehicles, and the Canister Closed Valve (CCV) and corresponding circuit were found to be within specifications, it may be necessary to inspect for flow restrictions within the EVAP ventilation system.
TSBTRA067
Service Bulletin/Repair Instructions
TSB - AUTOMATIC TRANSMISSION OIL PRESSURE CHARACTERISTIC VALUES DATA TRANSFER - This bulletin provides information regarding data transfer of automatic transmission (A/T) characteristic values on 2015MY-2018MY K900 (KH) vehicles equipped with A8TR1 8-speed A/T and 2017MY~ Sportage (QL), Forte (YDm), and Cadenza (YG) vehicles equipped with the GEN2 Type (A6MF2-2 6-speed / A8LF1 8-speed) A/T. The type of solenoid valve used to control gear shifts changed from indirect to direct control type to reduce oil capacity and improve fuel efficiency.
PS528
Service Bulletin/Repair Instructions
PITSTOP - Bluetooth Sound Quality Concerns on UVO eServices (UVO 3.0) (PS528) - This Pitstop provides information to diagnose and repair 2017-18MY Sportage (QL) and 2017MY Niro (DE HEV) vehicles, with UVO eServices (UVO 3.0) head units, produced after June 15, 2017, with Bluetooth® sound quality customer concerns.
TSBBOD174
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: WINDSHIELD MOLDING REPAIR FOR WIND NOISE (SA311) - This bulletin provides the procedure for applying LOCTITE® between the front windshield molding lip and panoramic static roof glass on some 2018MY Sportage (QL) vehicles, equipped with a Panoramic Roof, produced from April 3, 2017 through August 28, 2017, which may experience wind noise while driving at higher freeway speeds.
TSBCLI041
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: EVAPORATOR TEMPERATURE SENSOR AND/OR ECV REPLACEMENT (SA309) - This bulletin provides the procedure to replace the Evaporator Temperature Sensor and /or ECV (External Control Valve) on 2017-2018MY Sportage (QL) vehicles produced from December 1, 2015 through July 18, 2017, which may exhibit intermittent poor air conditioning performance.