L-SB-0017-25 Rev2
Service Bulletin/Repair Instructions
OBSOLETE NOTICE April 17, 2026: This bulletin is now obsolete. Please see L-SB-0009-26
Vehicle report
2022 LEXUS NX
Service bulletins
67 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
L-SB-0009-26
Service Bulletin/Repair Instructions
Some 2022 – 2024 model year NX 250 and NX 350, and 2023 – 2024 model year RX 350 vehiclesmay exhibit the following condition at vehicle startup when the vehicle is in Park: • A “Shift System Malfunction” message on the Multi-information Display (MID), as shown below. This condition is more likely to occur when the outside temperatures are near freezing. The Shift Actuator ECU logic has been modified to reduce the possibility of these conditions.
L-SB-0021-25
Service Bulletin/Repair Instructions
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
L-SB-0030-24 Rev2
Service Bulletin/Repair Instructions
Some 2005 – 2026 Lexus vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
L-SB-0052-25
Service Bulletin/Repair Instructions
Some 2022 – 2025 model year NX 450h+ and 2024 – 2025 RX 450h+ vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P019064 (Fuel Rail Pressure Sensor “A” Signal Plausibility Failure) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to address this condition.
25LD01
Service Campaign
The subject vehicles are equipped with a rear motor unit and an HV Floor Under Wire that provide high voltage to operate the motor. Mud, water, or road salt could potentially enter the HV Floor Under Wire connector housing and could cause corrosion over time. Excessive corrosion could cause AM Radio Static during certain driving cycles, or the vehicle may not start.
L-TT-0326-23 Rev2
Service Bulletin/Repair Instructions
Some customers may experience operational difficulties with some telematics features which they cannot resolve on their own. These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features.
L-SB-0027-25 Rev1
Service Bulletin/Repair Instructions
Some 2022 – 2025 model year NX 250, NX 350, NX 350h, and NX 450h+ vehicles may exhibit an abnormal noise when engaging the electronic parking brake.
25LC02
Service Bulletin/Repair Instructions
TECHNICAL INSTRUCTIONS FOR 25LC02 REPROGRAMMING FOR FORWARD RECOGNITION CAMERA CERTAIN 2022-2023 Model Year NX250 2022-2023 Model Year NX350 2022-2023 Model Year NX350H 2022-2023 Model Year NX450H
L-SB-0009-24 Rev1
Service Bulletin/Repair Instructions
Some 2021 – 2024 model year ES 250 and 2022 – 2024 model year NX 250 vehicles with A25A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
L-SB-0043-23 Rev1
Service Bulletin/Repair Instructions
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
L-TT-0340-25
Service Bulletin/Repair Instructions
To assist with the early detection and early resolution of audio related concerns you may be asked to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.
L-SB-0017-25
Service Bulletin/Repair Instructions
Some 2022 – 2024 model year NX 250 and NX 350, and 2023 – 2024 model year RX 350 vehicles may exhibit both of the following conditions at vehicle startup: •A “Shift System Malfunction” message on the Multi-information Display (MID), as shown below. •Battery voltage drops below 10V. These conditions are more likely to occur when the outside temperatures are near freezing. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of these conditions.
L-SB-0013-24 Rev1
Service Bulletin/Repair Instructions
The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.
L-SB-0036-22 Rev2
Service Bulletin/Repair Instructions
Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.
L-SB-0017-19 Rev1
Service Bulletin/Repair Instructions
Some 2010 – 2026 model year Lexus vehicles may exhibit paint stains after the removal of Rapgard™. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard™. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk.
L-SB-0021-23 Rev2
Service Bulletin/Repair Instructions
Some 2022 – 2025 model year Lexus vehicles may require the download and installation of vehicle specific software or configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU.
L-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Some 2022 – 2024 model year NX 250, NX 350, NX 350h, and NX 450h+ vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P162B87 (Lost Communication with Battery Monitor Module Missing Message). The battery state sensor assembly has been updated to prevent the condition from occurring.
L-TT-0336-24 Rev1
Service Bulletin/Repair Instructions
After jump-starting, the vehicle may experience a no-start condition and multiple DTCs including U010087 - Lost Communication with ECM/PCM "A" Missing Message. Upon investigation, it is found that the engine ECU has been damage and needs to be replaced. In several cases, the cause of the ECU damage was improper jump starting. Further investigation found that ECU damage may occur if the negative (ground) cable clamps are attached on or around the engine ECU or mounting bracket. To prevent this condition from occurring, it is recommended that the jumper cables be attached as described in the owner’s manual.
23LJ01
Service Campaign
The table below describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated over time as more details become available.
L-TT-0336-24
Service Bulletin/Repair Instructions
After jump-starting, the vehicle may experience a no-start condition and multiple DTCs including U010087 - Lost Communication with ECM/PCM "A" Missing Message. Upon investigation, it is found that the engine ECU has been damage and needs to be replaced. In several cases, the cause of the ECU damage was improper jump starting. Further investigation found that ECU damage may occur if the negative (ground) cable clamps are attached on or around the engine ECU or mounting bracket.
L-SB-0034-24
Service Bulletin/Repair Instructions
Some 2022 – 2024 model year NX 250 and NX 350 vehicles may exhibit a condition where the vehicle displays both a System Malfunction Visit Your Dealer warning message and a brake warning light without any associated Diagnostic Trouble Codes (DTCs).
L-SB-0035-24
Service Bulletin/Repair Instructions
Some 2022 – 2024 model year NX 250, NX 350, and NX 350h vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P162B87 (Lost Communication with Battery Monitor Module Missing Message). The battery state sensor assembly has been updated to prevent the condition from occurring.
22TE09
Service Bulletin/Repair Instructions
TECHNICAL INSTRUCTIONS FOR CUSTOMER SUPPORT PROGRAM 22TE09 HV FLOOR UNDER WIRE HARNESS AND REAR TRACTION MOTOR CABLE CORROSION CERTAIN 2022 MODEL YEAR NX450H+
23LE05
Service Bulletin/Repair Instructions
TECHNICAL INSTRUCTIONS FOR CUSTOMER SUPPORT PROGRAM 23LE05 HV FLOOR UNDER WIRE HARNESS AND REAR TRACTION MOTOR CABLE CORROSION CERTAIN 2022 MODEL YEAR NX350 HYBRID
L-SB-0030-24 Rev1
Service Bulletin/Repair Instructions
Some 2005 – 2024 Lexus vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
L-SB-0030-24
Service Bulletin/Repair Instructions
Some 2005 – 2024 Lexus vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
L-SB-0027-24
Service Bulletin/Repair Instructions
A head unit software update is now available for 2022 model year LX 600, NX 250, NX 350, NX 350h, and NX 450h+ vehicles equipped with Lexus Multimedia (version 1020 or earlier). This update provides improved performance and capability for the following: •User Profile configuration and display. •Cloud Navigation and Intelligent Voice Assistant. •Mobile device connectivity. •On-screen display and system settings/configuration. •Security enhancements. A head unit software update is now available for 2022 LX 600, NX 250, NX 350, NX 350h, and NX 450h+ vehicles equipped with Lexus Multimedia (earlier than version 1040). This software update includes the following improvements: •Cloud navigation. •Intelligent assistant voice recognition. •Showing and controlling explicit audio content. •User interface. •Bluetooth®. •Bug fixes. This software update removes the following feature: •Hybrid radio. A head unit software update is now available for 2023 model year LX 600, NX 250, NX 350, NX 350h, and NX 450h+ vehicles equipped with Lexus Multimedia (version 1040 or earlier). This software update provides improved performance and capability for the following: •User Profile. •Over-the-air (OTA) notifications. •Ability to search during a call. •Bug fixes settings/configuration. •Security enhancements. A head unit software update is now available for 2022 – 2023 model year LX 600 vehicles; 2023 – 2024 model year RX 350, RX 350h, RX 450h+, and RX 500h vehicles; 2022 – 2024 model year NX 250, NX 350, NX 350h, and NX 450h+ vehicles; 2023 model RZ 450e vehicles equipped with Lexus Multimedia (earlier than version 2050). This software update includes the following improvements: •User interface design. •Intelligent assistant. •Navigation lane guidance. •Phone book search. •Bug fixes. A head unit software update is now available for 2022 – 2024 model year LX 600, NX 250, NX 350, NX 350h, and NX 450h+ vehicles; 2023 – 2024 model year RX 350, RX 350h, RX 450h+, RX 500h, and RZ 450e vehicles; 2024 model year TX 350, TX 500h, and TX 550h+ vehicles equipped with Lexus Multimedia (earlier than version 2170). This software update includes the following improvements: •User Profile. •User interface. •Cloud navigation. •Intelligent assistant voice recognition. •Bug fixes.
L-SB-0025-24
Service Bulletin/Repair Instructions
Some 2022 model year NX 350, 2023 – 2024 model year RX 500h, and 2024 model year TX 500h vehicles equipped with a T24A-FTS engine may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P05CE00 (Cold Start “B” Camshaft Position Timing Performance Bank 1) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition.
L-TT-0323-23 Rev1
Service Bulletin/Repair Instructions
When setting up the Lexus Interface (21MM) user profile, if the QR code is not working please use the following recommendations. 1. Refer to the TAS 21MM Diagnostics Pre-Call Worksheet (PCW) on the TAS case creation page. The following steps will provide some answers for the PCW. 2. Start with the vehicle running outside for 5-10 minutes in an area with no overhead obstructions. a. Enter the radio Service Menu (diagnostic mode) using Techstream or GTS+, or the manual swiping method as outlined in the Repair Manual. b. Once the Service Menu is shown, the Function Check/Setting, and Product information buttons will be used. 3. Select the Product Information button to display radio and DCM registration details. 4. Accurate GNSS Date and Time is needed for the QR code to work. From the Service Menu select Function Check/Setting > System Sensors Check to display GNSS details.
L-SB-0020-24
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
L-SB-0021-24
Service Bulletin/Repair Instructions
Lexus vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. L-PG004-94. •The entire bulletin has been updated.
L-SB-0022-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Lexus vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
L-SB-0023-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
L-SB-0024-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Lexus paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. BO029-91. •The entire bulletin has been updated. Service Bulletin No. BO029-91 is obsolete
L-SB-0021-23 Rev1
Service Bulletin/Repair Instructions
Some 2022 – 2024 model year Lexus vehicles may require the download and installation of vehicle specific software or configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU. REVISION NOTICE April 18, 2024 Rev1: •Applicability has been updated to include 2024 model year GX 550, LX 600, NX 250, NX 350, NX 350h, NX 450h+, RX 350, RX 350h, RX 450h+, RX 500h, RZ 300e, RZ 450e, TX 350, TX 500h, and TX 550h+ vehicles. •The Introduction section has been updated. •The Operation Procedure section has been removed. •The Standard ECU Configuration Procedure and ECU Configuration Value Writing Procedure sections have been added.
23LJ01 Eligibility
Service Campaign
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated over time as more details become available.
23LJ01_P5_Dealer
Service Bulletin/Repair Instructions
DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.
Lexus Second Key
Service Bulletin/Repair Instructions
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated over time as more details become available.
LSB000924
Service Bulletin/Repair Instructions
TSB: Some 2021 ? 2024 model year ES 250 and 2022 ? 2024 model year NX 250 vehicles with A25A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F ? 41°F: ?P030027 ? Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold ?P030000 ? Random/Multiple Cylinder Misfire Detected ?P030100 ? Cylinder 1 Misfire Detected ?P030200 ? Cylinder 2 Misfire Detected ?P030300 ? Cylinder 3 Misfire Detected ?P030400 ? Cylinder 4 Misfire Detected Follow the Repair Procedure in this bulletin to address these conditions.
LSB000722
Service Bulletin/Repair Instructions
OBSOLETE NOTICE February 13, 2024: This bulletin is now obsolete. Please see L-SB-0006-23.
Dealer Packet pu
Service Bulletin/Repair Instructions
DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.
Vehicle Eligibil
Service Bulletin/Repair Instructions
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
L-SB-0006-23
Service Bulletin/Repair Instructions
TSB: A head unit software update is now available for 2022 model year LX 600, NX 250, NX 350, NX 350h, and NX 450h+ vehicles equipped with Lexus Multimedia (version 1020 or earlier). This update provides improved performance and capability for the following: ?User profile configuration and display. ?Cloud Navigation and Intelligent Voice Assistant. ?Mobile device connectivity. ?On-screen display and system settings/configuration. ?Security enhancements. A head unit software update is now available for 2022 LX 600, NX 250, NX 350, NX 350h, and NX 450h+ vehicles; and 2023 ES 250, ES 300h, ES 350, and UX 250h vehicles equipped with Lexus Multimedia (earlier than version 1040). This software update includes the following improvements: ?Cloud navigation. ?Intelligent assistant voice recognition. ?Showing and controlling explicit audio content. ?User interface. ?Bluetooth®. ?Bug fixes. This software update removes the following feature: ?Hybrid radio. A head unit software update is now available for 2023 model year LX 600, NX 250, NX 350, NX 350h, and NX 450h+ vehicles equipped with Lexus Multimedia (version 1040 or earlier). This software update provides improved performance and capability for the following: ?User profile. ?Over-the-air (OTA) notifications. ?Ability to search during a call. ?Bug fixes settings/configuration. ?Security enhancements. A head unit software update is now available for 2022 ? 2023 model year LX 600 vehicles; 2023 ? 2024 model year ES 250, ES 300h, ES 350, RX 350, RX 350h, RX 450h+, RX 500h, and UX 250h vehicles; 2022 ? 2024 model year NX 250, NX 350, NX 350h, and NX 450h+ vehicles; 2023 model year LS 500 and LS 500h vehicles; 2024 model year LC 500, LC 500C, and LC 500h vehicles equipped with Lexus Multimedia (earlier than version 2050). This software update includes the following improvements: ?User interface design. ?Intelligent assistant. ?Navigation lane guidance. ?Phone book se
23LJ01P4A
Service Bulletin/Repair Instructions
TI: TECHNICAL INSTRUCTIONS FOR 23LJ01 Second Key Delivery Program Multiple Models and Model Years
23LJ01P4
Service Bulletin/Repair Instructions
RL: The supply of Smart Keys available for Lexus vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.
LSB005523
Service Bulletin/Repair Instructions
TSB: Some 2018 ? 2024 model year Lexus vehicles may exhibit a hybrid system warning lamp occurring in below-freezing temperatures (below 32°F or 0°C). After performing a Health Check, one or both of the following Diagnostic Trouble Codes (DTCs) may be present: ?P1C8449 ? (High Voltage Power Resource Circuit Short during Ready ON) ?P300449 ? (High Voltage Power Resource Circuit Short during Pre-Charge) Follow the Repair Procedure in this bulletin to address this condition.
22LC03_DealerPac
Service Bulletin/Repair Instructions
DP: In the involved vehicles, a gear shift control unit may output incorrect or missing identification codes which may result in failure at state emissions inspections (SMOG check). While these vehicles may not meet certain state emissions requirements, this issue does not have an effect on the vehicle?s performance, emissions, or fuel efficiency.
23LC01 NX LSS+ D
Service Bulletin/Repair Instructions
DP:The subject vehicles are equipped with Lexus Safety Sense + (LSS+) which consists of several driving assist features, including pre-collision braking, lane departure warning, and more. Due to inappropriate programming of the software within the forward recognition camera, there is a possibility that under certain conditions, LSS+ functions could become inoperative for approximately 4 seconds before rebooting and becoming operational again.
L-SB-0051-23
Service Bulletin/Repair Instructions
TSB: Some 2022 ? 2024 model year NX 250 and NX 350 vehicles may exhibit a warning message on the Multi-information Display (MID) to apply the brakes when shifting out of Park into Drive or Reverse. The transmission floor shift assembly (SBW ECU) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to reprogram the transmission floor shift assembly.
23LJ01P3_TI_fina
Service Bulletin/Repair Instructions
TI: TECHNICAL INSTRUCTIONS FOR 23LJ01 Second Key Delivery Program Multiple Models and Model Years
23LJ01_Dealer Pa
Service Bulletin/Repair Instructions
DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.
23LJ01P3_RL_fina
Service Bulletin/Repair Instructions
RL: The supply of Smart Keys available for Lexus vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.
L-SB-0050-22 Rev
Service Bulletin/Repair Instructions
TSB: Some 2022 ? 2024 model year NX 250, 2022 ? 2023 model year NX 350, and 2022 model year NX 350h and NX 450h+ vehicles may exhibit a MIL ON condition with one or both of the following Diagnostic Trouble Codes (DTCs) present: ?P2E0464 (SAE code P2E05) ? Gear Lever Position Sensor ?B? Signal Plausibility Failure. ?P2E0064 (SAE code P2E01) ? Gear Lever Position Sensor ?A? Signal Plausibility Failure. The transmission floor shift assembly logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.
23LC01a
Service Bulletin/Repair Instructions
RL: The subject vehicles are equipped with Lexus Safety Sense + (LSS+) which consists of several driving assist features, including pre-collision braking, lane departure warning, and more. Due to inappropriate programming of the software within the forward recognition camera, there is a possibility that under certain conditions, LSS+ functions could become inoperative for approximately 4 seconds before rebooting and becoming operational again.
23LC01b
Service Bulletin/Repair Instructions
TI: TECHNICAL INSTRUCTIONS FOR 23LC01 LEXUS SAFETY SENSE+ INOPERATIVE INTERMITTENTLY
23LC01
Service Bulletin/Repair Instructions
DP: The subject vehicles are equipped with Lexus Safety Sense + (LSS+) which consists of several driving assist features, including pre-collision braking, lane departure warning, and more. Due to inappropriate programming of the software within the forward recognition camera, there is a possibility that under certain conditions, LSS+ functions could become inoperative for approximately 4 seconds before rebooting and becoming operational again
23TJ01c
Service Bulletin/Repair Instructions
DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.
23TJ01d
Service Bulletin/Repair Instructions
RL: The supply of Smart Keys available for Lexus vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.
23TJ01e
Service Bulletin/Repair Instructions
TI: TECHNICAL INSTRUCTIONS FOR 23LJ01 Second Key Delivery Program Multiple Models and Model Years
LSB004323
Service Bulletin/Repair Instructions
TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks.
LTT032623
Service Bulletin/Repair Instructions
TT: A very small percentage of customers experience operational difficulties with some telematics features which they cannot resolve on their own. These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features.
L-SB-0039-23
Service Bulletin/Repair Instructions
TSB: Some 2022 ? 2023 model year NX 250, NX 350, NX 350h (with 9.8-inch touchscreen only) and 2023 model year ES 250, ES 300h, and ES 350 (with 8.0-inch touchscreen only) vehicles, equipped with a 10-speaker premium sound system, may exhibit an echo condition during a phone call via Bluetooth®, Apple CarPlay®, or Android Auto? (wireless or wired). The person in the car does not hear or experience any echo or other abnormalities. The condition can be resolved by replacing the amplifier assembly.
L-SB-0037-23
Service Bulletin/Repair Instructions
TSB: Some 2021 ? 2024 model year Lexus vehicles use hub bolts in place of studs/nuts to fasten the wheels to the vehicle. If non-compatible wheels or hub bolts/nuts are installed, there is increased risk that the wheel(s) could come off resulting in a crash. This service bulletin outlines the physical differences and precautions that should be taken when servicing different wheel and wheel fastener types.
LTT-0324-23
Service Bulletin/Repair Instructions
TT: Some customers and technicians have reported the presence of bubbling, scratching, peeling or imperfections on the navigation display screen
LSB005822
Service Bulletin/Repair Instructions
Left-hand Side Outer Rear-view Mirror Vibration While driving
Customer Letter
Service Bulletin/Repair Instructions
Lexus NX Remote Park Guest Letter
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.