Vehicle report

2015 LINCOLN MKC

Compare every LINCOLN MKC yearNHTSA and EPA records

Service bulletins

147 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

25N15 S1

Other

Customer Satisfaction Program 25N15 - Supplement #1 Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacement

SSM 54366

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

TSB 25-2005

Service Bulletin/Repair Instructions

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: • Customer concern of a vibration or rough idle in D or R • Shudder while driving • Lack of engine RPM • Low performance, lack of acceleration on take off

SSM 53040

Service Bulletin/Repair Instructions

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

SSM 52335

Service Bulletin/Repair Instructions

For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

21B09 S2

Service Bulletin/Repair Instructions

Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit REASON FOR THIS SUPPLEMENT Program Terms & Urgency / Expiration Date: Program extension until July 31, 2023. Service Action: o IDS level 128 or higher is now required to address various programming issues encountered. o C-MAX Energi vehicles are now serviceable with new software and hardware. Labor Allowances: C-MAX labor has been updated. Parts Requirements / Ordering Information: o The C-MAX 4G Upgrade Kit is now orderable at this time with a new part number. o MKX Rear seat backrest nut claim quantity updated. Technical Information updates: o Ensure IDS level 128 or higher is used. o Toggling Valet Mode is no longer required. o C-MAX Energi instructions are now available. Owner Notification: Non-repaired vehicle owners will be mailed the week of April 17, 2023. Pickup and Delivery: Added Customer Acknowledgement Form - Review form contents with customer prior to kit ordering and obtain customer signature prior to installation for Focus BEV, C-MAX, and Fusion Energi vehicles.

SSM 51536

Service Bulletin/Repair Instructions

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

20B27 S1

Service Bulletin/Repair Instructions

Certain 2015-2019 MKC and 2016-2019 Explorer Vehicles Equipped With the 2.3L Engine and 6F35 Transmission Powertrain Control Module Reprogram Submitting Owner Letters

20N07 S2

Service Bulletin/Repair Instructions

Certain 2015-2019 MKC and 2016-2019 Explorer Vehicles Equipped With the 2.3L Engine and 6F35 Transmission - Transmission Extended Warranty Coverage Updated Owner Letters: 20N07/20B27 S1

TSB 22-2309

Service Bulletin/Repair Instructions

Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

21B09-S1

Service Bulletin/Repair Instructions

Certain 2014-2020 Model Year Multiple Vehicle Lines - 3G Telematics Control Unit to 4G Upgrade Kit. The North America 3G cellular service began decommissioning in August 2021 and a complete shutdown of the 3G network took place in February 2022. Vehicles on the road equipped with a 3G telematics control unit (TCU) / embedded modem will lose mobile app functionality/connectivity.

TSB 22-2287

Service Bulletin/Repair Instructions

Some 2015-2019 MKC and 2016-2019 Explorer vehicles equipped with a 2.3L engine may exhibit a vibration/rough idle when the vehicle is in drive (D) or reverse (R). The vehicle may also exhibit a lack of engine revolutions per minute (RPM), lack of acceleration on take off and/or shudder while driving. This may be due to the torque converter overheating causing damage to the torque converter as well as possible internal damage to the transmission. To correct this condition, follow the Service Procedure to replace the torque converter and specified internal transmission components that may have been damaged.

TSB 22-2230

Service Bulletin/Repair Instructions

Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

SSM 50804

Service Bulletin/Repair Instructions

Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

TSB 22-2162

Service Bulletin/Repair Instructions

Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

TSB 22-2104

Service Bulletin/Repair Instructions

This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

SSM 50257

Service Bulletin/Repair Instructions

Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.

21B09

Service Bulletin/Repair Instructions

Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit The North America 3G cellular service began decommissioning in August 2021 and will be fully decommissioned in February 2022. Vehicles on the road equipped with a 3G telematics control unit (TCU) / embedded modem will lose mobile app functionality/connectivity. Some owners are still within the *complimentary trial period (depending on model year and brand, see table below) for connected services.

SSM 50067

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

TSB 21-2236

Service Bulletin/Repair Instructions

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

SSM 49821

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

20N07-S2

Service Bulletin/Repair Instructions

This program extends the warranty coverage of the automatic transmission torque converter for twelve (12) months from the RO date of Powertrain Control Module reflash under Customer Satisfaction Program 20B27.

TSB 20-2271

Service Bulletin/Repair Instructions

Some 2015-2019 MKC and 2016-2019 Explorer vehicles equipped with a 2.3L engine may exhibit a vibration/rough idle when the vehicle is in DRIVE or REVERSE. The vehicle may also exhibit a lack of engine revolutions per minute (RPM), lack of acceleration on take off and/or shudder while driving. This may be due to the torque converter overheating causing damage to the torque converter as well as possible internal damage to the transmission. To correct this condition, follow the Service Procedure steps to replace the torque converter and specified internal transmission components that may have been damaged.

20N07-S1

Service Bulletin/Repair Instructions

In some of the affected vehicles, customers may experience adverse NVH, vibration and/or rough idle in Drive or Reverse, low performance/lack of acceleration during launch, sluggish vehicle operation and shudder while driving

20B27

Service Bulletin/Repair Instructions

In affected vehicles, the transmission torque converter may overheat in certain driving conditions. If the torque converter overheats it can lead to adverse NVH, rough idle, and low performance concerns. Ultimately this will require internal transmission repairs to resolve the concern. Ford Motor Company has developed and update to the Powertrain Control Module software that helps protect the transmission torque converter from overheating when exposed to certain driving styles.

20N07

Service Bulletin/Repair Instructions

In some of the affected vehicles, customers may experience adverse NVH, vibration and/or rough idle in Drive or Reverse, low performance / lack of acceleration during launch, sluggish vehicle operation and shudder while driving.

SSM 49210

Service Bulletin/Repair Instructions

Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

SSM 48858

Service Bulletin/Repair Instructions

Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

TSB 20-2171

Service Bulletin/Repair Instructions

Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

SSM 48619

Service Bulletin/Repair Instructions

SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

SSM 48423

Service Bulletin/Repair Instructions

Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 48397

Service Bulletin/Repair Instructions

Some 2013-2015 Fusion/MKZ/Escape/MKC with a 1.6L GTDI, 1.5L GTDI, or 2.0L GTDI may exhibit a lack of power, loss of power, or stall when placed in gear with DTCs P00C6, P0087, P008A, P008B, P018C, or P018D. If normal diagnosis leads to a biased or failed Fuel Low Pressure (FLP) sensor, the sensor is available without the need to order the entire fuel line assembly. The FLP sensor, located on the fuel supply line to the high pressure pump, provides the low side fuel pressure input to the PCM so the Fuel Driver Module can be controlled accordingly. The FLP PID can be viewed in the Datalogger and then compared to a manual pressure gauge per pinpoint test HC in the PCED to validate the sensor is working properly. The Fusion/MKZ catalog has been updated to show the sensor availability.

SSM 48135

Service Bulletin/Repair Instructions

Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

SSM 48130

Service Bulletin/Repair Instructions

Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

SSM 48123

Service Bulletin/Repair Instructions

For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

SSM 48108

Service Bulletin/Repair Instructions

Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

SSM 48049

Service Bulletin/Repair Instructions

Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

TSB 19-2200

Service Bulletin/Repair Instructions

Some 2015-2016 MKC vehicles may exhibit a wind or whistle noise from the exterior mirror(s) at highway speed. This may be due to the spacing between the exterior mirror base and the mirror cover. To correct the condition, follow the Service Procedure steps to add foam to the back of the mirror cover for the affected side(s).

TSB 19-2172

Service Bulletin/Repair Instructions

Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.

SSM 47996

Service Bulletin/Repair Instructions

Some 2015-2019 MKC vehicles built on or before 01-Apr-2019 may exhibit an air conditioning (A/C) system with a difference in the discharge temperature between the left and right vents. The left vent discharge temperature will usually be warmer than the right vent discharge temperature. Reprogram the front controls interface module (FCIM) using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18842 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 47976

Service Bulletin/Repair Instructions

On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

SSM 47967

Service Bulletin/Repair Instructions

Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

SSM 47850

Service Bulletin/Repair Instructions

SSM 47948

Service Bulletin/Repair Instructions

SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

TSB 19-2037

Service Bulletin/Repair Instructions

Some 2015-2019 MKC vehicles equipped with memory mirrors built on or before 16-Feb-2019 may experience a ratcheting/clicking noise from the exterior mirror(s) glass which can occur when one or more of the following actions occur: customer unlocks vehicle, memory mirrors glass position recall to previous setting or memory mirrors button activation.

SSM 47824

Service Bulletin/Repair Instructions

Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

TSB 19-2017

Service Bulletin/Repair Instructions

Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

SSM 47749

Service Bulletin/Repair Instructions

Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

TSB 18-2392

Service Bulletin/Repair Instructions

Some 2015-2019 MKC vehicles may exhibit an electronic power assist steering (EPAS) gear clatter-type noise over bumps that is only present on extremely rough road surfaces. Follow the Service Procedure steps to correct the condition.

TSB 18-2361

Service Bulletin/Repair Instructions

Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.

SSM 47678

Service Bulletin/Repair Instructions

2013-2019 Escape and 2015-2019 MKC vehicles equipped with a power roof opening panel will exhibit a small vent opening position of 5 mm (.197 in). This is the normal vent position for optimal noise, vibration, harshness (NVH) and windnoise qualities. When the vent is closed, the front sliding glass panel will open to the 10 mm (.394 in) position and then close. The front sliding glass panel also opens to the 10 mm (.394 in) position to give the front sliding glass panel enough clearance before it opens to the rearward position. This is a normal operating characteristic of the front sliding glass panel. No repairs are required.

SSM 47662

Service Bulletin/Repair Instructions

For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

SSM 47634

Service Bulletin/Repair Instructions

Some 2013-2019 Escape and 2015-2019 MKC vehicles may exhibit a vibration attributed to the tires. Prior to performing any road force balancing procedures or related diagnosis, make sure the vehicle tire pressure is correct and is driven a minimum of 24 Km (15 miles) to eliminate any possible flat spotting conditions and potential misdiagnosis. Refer to Workshop Manual (WSM), Section 204-04A for further information. In addition, it is recommended that diagnosis of tire/wheel vibration should not be performed on tires with less than 320 Km (200 miles). Some initial tire/wheel vibration issues (such as flat spotting) may correct themselves after the tires have been in service for 320 Km (200 miles). Setting tire pressure to the correct placard pressure is contained within pre-delivery inspection.

SSM 47635

Service Bulletin/Repair Instructions

When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

SSM 47638

Service Bulletin/Repair Instructions

2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.

SSM 47539

Service Bulletin/Repair Instructions

Some 2015-2019 MKC vehicles may exhibit a whistle and/or wind noise at highway speed from the exterior mirror area. Use Workshop Manual (WSM), Section 100-04 and 501-00 for diagnosis of whistle and/or wind noise. If the exterior mirror(s) are identified as the source of the noise verify the distance between the exterior mirror base and the mirror cover before attempting other repairs. A minimum measurement of 1mm (0.0393 in) should be present between the exterior mirror base and the mirror cover. Refer to WSM, Section 501-09 for information on measuring and adjusting the distance between the exterior mirror base and mirror cover. If a minimum measurement of 1mm (0.0393 in) is not maintained between the exterior mirror base and the mirror cover when the exterior mirror(s) are serviced it may create a whistle and/or wind noise concern.

SSM 47489

Service Bulletin/Repair Instructions

TSB 18-2255

Service Bulletin/Repair Instructions

Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.

SSM 47462

Service Bulletin/Repair Instructions

2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures

SSM 47430

Service Bulletin/Repair Instructions

If a trailer hitch receiver is installed on a 2013-2018 Escape or 2015-2019 MKC vehicle equipped with a hands-free liftgate, the hands-free liftgate function will become inoperative. Hands-free liftgate function can be restored by replacing the existing hands-free liftgate actuation upper sensor (14F680), lower sensor (14F680), stone deflector (17779), hands-free liftgate actuation module (14B291), plastic fasteners (N807951S) and screws (W506964) that are required for the factory installed trailer hitch receiver with hands-free liftgate option. Replacement of these parts to restore hands-free liftgate function is not warrantable. Regardless of trailer hitch configuration, the hands-free liftgate system cannot be added to a vehicle that was originally built without the hands-free liftgate option.

SSM 47392

Service Bulletin/Repair Instructions

2015-2019 MKC vehicles are equipped with a satin chrome front grille and roof moldings. If they require cleaning due to stains, water spotting, or discoloring do not use Motorcraft Custom Bright Metal Cleaner which is used for bright chrome components. The following products are recommended for satin chrome components: Meguiar's M02 Mirror Glaze Fine Cut Cleaner (Product #M0216), Meguiar's Water Spot Remover (Product #A3714) or Turtle Wax Renew RX Premium All Metal Polish (SKU T284) or equivalent. Follow the manufacturers cleaning instructions.

SSM 47201

Service Bulletin/Repair Instructions

Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.

SSM 47204

Service Bulletin/Repair Instructions

Some 2015-2018 Fusion/MKZ/MKC/Escape/Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a runs rough condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.

SSM 47160

Service Bulletin/Repair Instructions

Some 2015-2017 MKC/MKZ, 2016-2017 MKX and 2017 Continental vehicles equipped with a Telematics Control Unit (TCU) built on or before 15-Aug-2017 may exhibit inoperative remote features via Lincoln Way Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU Field Service Actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.06 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

SSM 47080

Service Bulletin/Repair Instructions

2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

SSM 47070

Service Bulletin/Repair Instructions

When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

SSM 47000

Service Bulletin/Repair Instructions

Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

SSM 46900

Service Bulletin/Repair Instructions

Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

SSM 46792

Service Bulletin/Repair Instructions

Some 2015-2018 MKC vehicles equipped with a AC power outlet socket may exhibit a condition with the assembly door becoming disconnected, jammed or locked closed. If the door is disconnected, re-install the end cap and door. Refer to updated Workshop Manual (WSM), Section 414-05 for correct door/spring position installation. If door is jammed or locked closed, this may be due to the door spring not being properly positioned when the door is installed. Do not try to force the door open as this may cause damage to the door or interfacing components. Remove the floor console rear end cap and dislodge the door by pushing it from the back side of the end cap. Reinstall the end cap and door. Refer to updated WSM, Section 414-05 for the correct door/spring position installation.

SSM 46723

Service Bulletin/Repair Instructions

Some 2015-2016 MKC vehicles without active park assist and built on or before 2/15/16 may exhibit steering column controls such as turn signals, radio controls, and low speed wipers being intermittently inoperative due to lack of communication. Wake up the steering column control module (SCCM) by actuating the headlight flash to pass function and reprogram the SCCM with latest calibration using IDS release 106.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. Use causal part 3F791 and refer to section 10 body/chassis/electrical in the SLTS manual for applicable labor operations.

SSM 46724

Service Bulletin/Repair Instructions

Some 2015-2016 MKC vehicles equipped with active park assist may exhibit turn signals, steering wheel radio controls and low speed wipers being inoperative. The stability/traction control indicator lamp may also be illuminated with Diagnostic Trouble Code (DTC) U0131. It may be required to perform the Steering Column Control Module (SCCM) reprogramming function twice to ensure the module is successfully programmed. Reprogram the SCCM with latest calibration using the Integrated Diagnostic System (IDS) release 106.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Use causal part 3F791 and refer to section 10 body/chassis/electrical in the SLTS manual for applicable labor operations.

SSM 46703

Service Bulletin/Repair Instructions

Some 2013-2017 Edge/MKX/Escape/MKC/Fusion/MKZ/Flex/MKT/Mondeo/Kuga/EcoSport AWD vehicles where diagnosis leads to a RDU clutch issue, a rear drive unit (RDU) service kit is available. Use the vehicle identification number (VIN) in the parts catalog to look for base part 4A232. If clutch assembly (base 4A232) is not listed in the catalog, this message does not apply. For vehicle repairs refer to updated Workshop Manual (WSM), Section 205-02 on ATC clutch repairs. Use causal part 4A232 or equivalent and applicable labor operations.

SSM 46495

Service Bulletin/Repair Instructions

SOME 2015-2017 ESCAPE AND MKC VEHICLES WITHOUT A VEHICLE DYNAMIC SUSPENSION SYSTEM AND BUILT ON 1-APR-2015 AND THROUGH 1-OCT-2016 MAY EXHIBIT A RATTLE AND/OR CLUNKING NOISE FROM THE REAR SUSPENSION WHILE DRIVING OVER BUMPS AND/OR MAKING TURNS AT LOW SPEEDS. SUSPECT REAR SHOCK ABSORBERS WILL COMPRESS 2-5 INCHES OF TRAVEL BEFORE SIGNIFICANT RESISTANCE IS OBSERVED. IF WORKSHOP MANUAL (WSM), SECTION 100-04 DIAGNOSTICS INDICATE A RATTLE AND/OR CLUNKING NOISE IS COMING FROM THE REAR SHOCK ABSORBER(S) THEN REFER TO WSM, SECTION 204-02 AND REPLACE THE REAR SHOCK ABSORBER(S)AS REQUIRED. FOR CLAIMING, USE CAUSAL PART 18125 AND APPLICABLE LABOR OPERATIONS IN SECTION 5 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

SSM 46371

Service Bulletin/Repair Instructions

SOME 2012-2017 FOCUS ELECTRIC/2013-2017 CMAX ENERGI/FUSION ENERGI/2015-2017 MKC/MKZ/2016-2017 MKX AND 2017 CONTINENTAL VEHICLES OPERATING WITH A 3G TCU ON OR BEFORE 16-JAN-2017 MAY NOT RESPOND TO CUSTOMERS REMOTE COMMANDS VIA MYLINCOLN/MYFORD MOBILE PHONE APPLICATIONS. 2G NETWORKS WERE DECOMMISSIONED ON 16-JAN-2017. IF THE 3G TCU WAS OPERATING ON A 2G NETWORK, IT WILL NOT AUTOMATICALLY ATTEMPT TO RECONNECT TO THE REPLACEMENT 3G NETWORK. TO CORRECT, RESET THE TCU BY REMOVING ITS POWER FUSE FOR 5 MINUTES. IF THE CONCERN IS STILL PRESENT, FOLLOW NORMAL DIAGNOSTICS IN WORKSHOP MANUAL (WSM), SECTION 415-00. REFER TO PTS OASIS HOME PAGE FOR TCU VERSION IDENTIFICATION. FOR CLAIMING, USE CAUSAL PART 14G229 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

SSM 46355

Service Bulletin/Repair Instructions

MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

SSM 46332

Service Bulletin/Repair Instructions

REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.

SSM 46295

Service Bulletin/Repair Instructions

TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

SSM 46281

Service Bulletin/Repair Instructions

SOME 2015-2017 EDGE/MKX, ESCAPE/MKC, FUSION/MKZ AND EXPLORER VEHICLES EQUIPPED WITH A 2.0L OR 2.3L MAY EXHIBIT DAMAGE TO THE ENGINE APPEARANCE COVER, VALVE COVER AND/OR INTAKE MANIFOLD WHEN ATTEMPTING TO REMOVE THE APPEARANCE COVER. TO REDUCE THE POSSIBILITY OF DAMAGE, CAREFULLY PULL STRAIGHT UPWARD ON THE UNDERSIDE OF THE COVER AT EACH FASTENER LOCATION TO REMOVE. DO NOT PULL THE COVER FORWARD OR TO THE SIDE. BEFORE INSTALLING THE ENGINE APPEARANCE COVER, APPLY MOTORCRAFT SILICONE BRAKE CALIPER GREASE AND DIELECTRIC COMPOUND (XG-3-A) TO THE COVER FASTENER GROMMETS. WORKSHOP MANUAL (WSM) INFORMATION IS IN THE PROCESS OF BEING UPDATED

15N04-S2

Service Bulletin/Repair Instructions

CERTAIN 2015 MODEL YEAR MKC AND MKZ VEHICLES EQUIPPED WITH THE RESERVE EQUIPMENT GROUP, AND CERTAIN 2012-2016 FOCUS ELECTRIC, C-MAX ENERGI, AND FUSION ENERGI VEHICLES - EMBEDDED MODEM REPLACEMENT.

SSM 46210

Service Bulletin/Repair Instructions

SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.

SSM 46153

Service Bulletin/Repair Instructions

SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.

SSM 46155

Service Bulletin/Repair Instructions

SOME 2015-2017 MKC, 2016 MKX, AND 2016-2017 MKZ VEHICLES EQUIPPED WITH A TELEMATICS CONTROL UNIT (TCU) BUILT ON OR BEFORE 19-OCT-2016 MAY EXHIBIT LOSS OF FUNCTIONALITY OF REMOTE FEATURES VIA THE MYLINCOLN MOBILE APPLICATION. TO CORRECT THE CONDITION, PROGRAM THE TCU TO THE LATEST CALIBRATION USING IDS VERSION 102.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST CALIBRATION. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR 2015 MKC/MKZ VEHICLES MAKE SURE FSA 15N04 HAS BEEN COMPLETED PRIOR TO ATTEMPTING REPROGRAMMING. IF FSA 15N04 HAS BEEN COMPLETED AND THE TCU IS AT THE LATEST CALIBRATION, THEN REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSTICS. USE CAUSAL PART 14G229 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL

SSM 46132

Service Bulletin/Repair Instructions

SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

SSM 46129

Service Bulletin/Repair Instructions

SOME 2013-2016 FUSION/ESCAPE/MKT/FLEX/MKS/TAURUS, 2015-2016 MKZ/MKC/EDGE AND 2016 MKX VEHICLES MAY EXHIBIT VARIOUS RADIO CONCERNS INCLUDING: SPEAKER STATIC WITH KEY-OFF, NO AUDIO AFTER VEHICLE IS FIRST STARTED WITH DIAGNOSTIC TROUBLE CODE (DTC) U0184, NO VOLUME CONTROL, OR A STUCK CD WITH NO SLOT BLOCKAGE. PRIOR TO STARTING NORMAL DIAGNOSIS FOR ANY OF THESE CONDITIONS, VERIFY THE ACM IS AT THE LATEST CALIBRATION USING IDS VERSION 102.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE THE APPLICABLE LABOR OPERATION IN SECTION 11 OF THE SLTS MANUAL AND CAUSAL PART 18C869 WHEN CLAIMING THIS REPAIR.

SSM 46118

Service Bulletin/Repair Instructions

WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.

SSM 46102

Service Bulletin/Repair Instructions

Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.

SSM 46104

Service Bulletin/Repair Instructions

2015-2017 Lincoln MKC is equipped with satin chrome front grille and roof moldings. If they require cleaning due to stains, water spotting, or discoloring do not use Motorcraft Custom Bright Metal Cleaner which is used for bright chrome components. The following products are recommended for satin chrome components: Meguiar's M02 Mirror Glaze Fine Cut Cleaner (Product #M0216), Meguiar's Water Spot Remover (Product #A3714) or Turtle Wax Renew RX Premium All Metal Polish (SKU T284) or equivalent. Follow the manufacturers cleaning instructions.

SSM 46105

Service Bulletin/Repair Instructions

Some 2015-2016 MKC, 2016 MKX, and 2016-2017 MKZ vehicles equipped with a Telematics Control Unit (TCU) built on or before 9-Aug-2016 may exhibit loss of functionality of remote features via the MyLincoln Mobile Application. To correct the condition, program the TCU to the latest calibration using IDS version 102.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest calibration. Calibration files may also be obtained at www.motorcraftservice.com. For 2015 MKC/MKZ vehicles make sure FSA 15N04 has been completed prior to attempting reprogramming. If FSA 15N04 has been completed and the TCU is at the latest calibration, then refer to WSM, Section 415-00 for normal diagnostics. Use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

SSM 46085

Service Bulletin/Repair Instructions

The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

TSB 16-0123

Service Bulletin/Repair Instructions

Some 2015-2016 MKC vehicles equipped with a 2.3L GTDI engine may exhibit an illuminated MIL with a lack of power and diagnostic trouble code (DTC) P0299. This may be due to the turbocharger wastegate actuator rod coming disconnected from the wastegate. Follow the Service Procedure steps to correct the condition.

SSM-45838

Service Bulletin/Repair Instructions

INOPERATIVE HANDS-FREE LIFTGATE AFTER ADDITION OF TRAILER HITCH

TSB16-0110

Service Bulletin/Repair Instructions

SOME 2015-2016 LINCOLN MKC VEHICLES EQUIPPED WITH A 2.3L GTDI ENGINE AND BUILT ON OR BEFORE 2/23/2016 MAY EXHIBIT A HEAVY CONTINUOUS BLUE SMOKE WITH A BURNING OIL SMELL AFTER IDLING 10 MINUTES OR LONGER.

SSM 46022

Service Bulletin/Repair Instructions

SSM 45972

Service Bulletin/Repair Instructions

SOME 2015-2016 MKC VEHICLES EQUIPPED WITH MEMORY MIRRORS BUILT ON OR BEFORE 12/7/2015 MAY EXPERIENCE A RATCHETING/CLICKING NOISE FROM THE EXTERIOR MIRROR(S)GLASS WHEN ONE OR MORE OF THE FOLLOWING ACTIONS OCCUR: VEHICLE UNLOCKED, VEHICLE FIRST STARTED, MEMORY MIRROR BUTTONS ACTIVATED OR WHEN POWER FOLD MIRRORS ARE OPERATED. REPROGRAM THE DRIVER DOOR MODULE (DDM) AND/OR PASSENGER DOOR MODULE (PDM) WITH LATEST CALIBRATION USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 101.04 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART 14B291 AND REFER TO SECTION 10 IN THE SLTS MANUAL FOR APPLICABLE LABOR OPERATIONS.

SSM 45951

Service Bulletin/Repair Instructions

SOME 2015-2017 MKC VEHICLES EQUIPPED WITH A DSP MODULE MAY EXHIBIT DIAGNOSTIC TROUBLE CODES (DTCS) B1A10, B1A11, B1045 AND/OR B13FD WITH NO OBSERVABLE AUDIO MALFUNCTION AFTER PERFORMING A DSP MODULE ON-DEMAND SELF TEST. IF ANY OF THESE DTCS ARE PRESENT, PERFORM THE SPEAKER WALK AROUND TEST. REFER TO BEZEL DIAGNOSTICS IN WORKSHOP MANUAL (WSM), SECTION 415-00. IF THE SPEAKER WALK AROUND TEST PASSES AND NO AUDIO SYSTEM MALFUNCTION IS OBSERVED DISREGARD THE DTC(S). THESE CODES CANNOT BE CLEARED FROM THE DSP MODULE. IF THE SPEAKER WALK AROUND TEST FAILS OR AN AUDIO SYSTEM MALFUNCTION IS OBSERVED CONTINUE WITH NORMAL DIAGNOSTICS. REFER TO WSM, SECTION 415-00.

SSM 45926

Service Bulletin/Repair Instructions

2013-2017 FUSION/ESCAPE/MKZ (EXCLUDING 3.7L), 2015-2016 EDGE/EXPLORER (EXCLUDING 3.5L/3.7L), 2015-2016 MKC, AND 2016 MKX VEHICLES (EXCLUDING 3.7L) EQUIPPED WITH ALL WHEEL DRIVE (AWD) MAY EXHIBIT A LEAKING PASSENGER SIDE POWER TRANSFER UNIT (PTU) HALFSHAFT/LINKSHAFT SEAL. THIS MAY BE DUE TO A WORN PTU BUSHING. THE PTU BUSHING CAN NOW BE REPAIRED WITHOUT PTU REPLACEMENT. THE ONLINE WSM IS BEING UPDATED FOR ALL LISTED VEHICLES.REFER TO THE INTERMEDIATE SHAFT BUSHING REMOVAL AND INSTALLATION IN WORKSHOP MANUAL (WSM), SECTION 308-07. THE PROCEDURE IS THE SAME FOR ALL VEHICLES. IF THE PROCEDURE IS NOT PUBLISHED FOR THE VEHICLE BEING SERVICED CHECK THE WSM OF ANOTHER LISTED VEHICLE. BUSHING PART NUMBER IS F2GZ-63600A58A. THE PARTS CATALOG IS BEING UPDATED TO INCLUDE THIS BUSHING.

SSM-45858

Service Bulletin/Repair Instructions

2015-2016 MKC - WITHOUT ACTIVE PARK ASSIST INTERMITTENTLY INOPERATIVE STEERING COLUMN CONTROLS BUILT ON OR BEFORE 2/15/2016

SSM-45859

Service Bulletin/Repair Instructions

2015-2016 MKC - ACTIVE PARK ASSIST INOPERATIVE STEERING COLUMN CONTROLS WITH STABILITY/TRACTION CONTROL LAMP ILLUMINATED WITH DTC U0131

SSM-45837

Service Bulletin/Repair Instructions

SQUEAKING/CREAKING NOISE LEFT REAR - BODY FLEX OR TWIST CONDITIONS: LOW SPEED TURNS, OVER BUMPS AND TURNS INTO DRIVEWAYS WITH INCLINES

SSM-45821

Service Bulletin/Repair Instructions

SIRI EYES FREE FUNCTIONAL ISSUES USING BLUETOOTH AND APPLE IOS 9.2 AND 9.2.1

SSM-45815

Service Bulletin/Repair Instructions

AIR CONDITIONING (A/C) INOPERATIVE - DIAGNOSTIC TROUBLE CODE (DTC) P0645

SSM-45810

Service Bulletin/Repair Instructions

A/C COMPRESSOR LOCKUP - VEHICLES IN STORAGE OR USED INFREQUENTLY

SSM-45797

Service Bulletin/Repair Instructions

DRIVE MINIMUM 15 MILES BEFORE DIAGNOSING TIRE VIBRATIONS

16-0066

Service Bulletin/Repair Instructions

Some 2012-2016 vehicles equipped with a touchscreen navigation system and the language set to Arabic may exhibit a blank screen. This may be the result of the ribbon cables not being fully seated inside the front display interface module (FDIM) or an improper software configuration of the FDIM.

TSB160066

Service Bulletin/Repair Instructions

Touchscreen navigation system - arabic language - blank screen

16-0058

Service Bulletin/Repair Instructions

Some 2015-2016 MKC and 2016 MKX vehicles may exhibit a wind or whistle noise from the exterior mirror(s) at highway speed.

TSB160058

Service Bulletin/Repair Instructions

Wind or whistle noise froim exterior mirror(s) at highway speed

16-0045

Service Bulletin/Repair Instructions

2.0L ECOBOOST - FUEL ODOR ISSUE Some 2013-2016 Escape, 2015-2016 MKC vehicles built on or before 12/15/2015, 2013-2016 Fusion, MKZ, 2013-2015 Explorer, 2013-2014 Focus ST and Edge vehicles equipped with 2.0L EcoBoost engines may exhibit fuel odor originating from the positive crankcase ventilation (PCV) hose. SERVICE PROCEDURE 1. Is the vehicle a 2016 Escape or MKC? a. Yes - check the vehicle build date. Was the vehicle built on or before 12/15/2015? (1) Yes - proceed to Step 2. (2) No - this article does not apply. b. No - proceed to Step 2. 2. Inspect the PCV hose to make sure it is properly connected to the valve cover and the low pressure intake duct. a. For Escape and Focus ST vehicles remove the cowl panel grille to access the hose. Refer to Workshop Manual (WSM), Section 501-02. b. For Edge vehicles remove the air cleaner outlet pipe to access the hose. Refer to WSM, Section 303-12. 3. Does the PCV hose exhibit a fuel smell or was the hose disconnected? a. Yes - replace hose and reassemble the vehicle. b. No - Refer to WSM, Section 303-13 for normal diagnosis.

TSB160045

Service Bulletin/Repair Instructions

2.0L Ecoboost - Fuel odor

Service

Service Bulletin/Repair Instructions

Online automotive service information system for March 2016

LTR3756

Service Bulletin/Repair Instructions

49 CFR Part 579.5 Monthly Communications - January 2016

TSB160001

Service Bulletin/Repair Instructions

49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C

SB-45302

Service Bulletin/Repair Instructions

FORD: UNRESPONSIVE TOUCH SCREEN ON SOME VEHICLES OR WITH NO INPUT BY USER, ACT AS IF BEING TOUCHED *CN

SB-45309

Service Bulletin/Repair Instructions

2015-2016 MKZ AND 2015 MKC INSTRUMENT CLUSTER MESSAGE CENTER ARTIST/TITLE AND TRACK MISSING AND IC NEEDS REPROGRAM WITH LATEST SOFTWARE CALIBRATION *CN

TSB15-0135

Service Bulletin/Repair Instructions

LINCOLN: 2015 MKC FROM EXTERIOR MIRRORS, WIND OR WHISTLING NOISE MAY BE EXPERIENCE, WHILE AT HIGHWAY SPEEDS *CN

TSB15-0136

Service Bulletin/Repair Instructions

FORD 2015 EDGE AND LINCOLN 20115 MKC DUE TO INTERFERENCE WITH CELLULAR PHONE TOWER SIGNALS VEHICLES WITH SIRIUS RADIO MAY SHOW CONCERN WHERE THE AUDIO CUTS OUT AND RADIO DISPLAYS NO SIGNAL MESSAGE *CN

SB-45317

Service Bulletin/Repair Instructions

2016 MKZ,MKC AND MKX: MY LINCOLN MOBILE APP NOT ABLE TO CONNECT TO VEHICLES EQUIPPED WITH DTC U2100 AND/OR U2101 ON VEHICLES WITH TELEMATICS CONTROL UNIT *CN

44863

Service Bulletin/Repair Instructions

FORD: NO SERVICE ACTION IS RECOMMENDED FOR THIS CONDITION. PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA

ASI-45207

Service Bulletin/Repair Instructions

FORD/LINCOLN: SOME VEHICLES ARE EXPERIENCING MALFUNCTION OF SYNC 3 ACCESSORY INTERFACE PROTOCOL MODULE (APIM) DIAGNOSTIC CODE U3000 OR B108E. MODEL 2016 ESCAPE. MKC. *PE

ASI-45211

Service Bulletin/Repair Instructions

LINCOLN/FORD: ONCE PROCEDURE FOR HEATED STEERING WHEEL MODULE PROGRAM COMPLETED, HEATED STEERING WHEEL FAILS TO OPERATE PROPERLY AND PASSES NETWORK TEST BUT FAILS ON DEMAND SELF TEST. MODEL 2011-15 FUSION F-150, EXPLORER, TAURUS, SUPER DUTY, MKZ, MKC, MKS, MKT, MKX. *PE

ASI-45212

Service Bulletin/Repair Instructions

FORD: SOME VEHICLES AND TRUCKS ARE EXPERIENCING A MALFUNCTION WITH THE HEATED STEERING WHEEL BECOMING INOPERATIVE AND ON DEMAND TEST FAILURE. MODEL 2014-15 FUSION, 2011-15 MKX, 2013-15 SUPER DUTY, EXPLORER, TAURUS, MKS, MKT, 2015 F-150, MKZ, MKC, 2011-15 MKX. *PE

ASI-45225

Service Bulletin/Repair Instructions

LINCOLN/FORD: SOME VEHICLES WILL EXPERIENCE TIRE VIBRATION AND POSSIBLE FLAT SPOTTING. VEHICLE NEEDS TO BE CHECKED AND DRIVEN, BY WORKSHOP TECH, APPROXIMATELY 15 MILES FOR DIAGNOSIS OF VIBRATIONS AND FLAT SPOTTING. MODEL 2013-16 ESCAPE, 2015-16 MKC. *PE

ASI-45254

Service Bulletin/Repair Instructions

FORD/LINCOLN: SOME VEHICLES WILL EXPERIENCE A NON RESPONSIVE OR NO USER INPUT (TOUCH) ON THE TOUCH SCREEN. MODEL 2016 ESCAPE, MKC. *PE

ASI-45174

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

ASI-45183

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

15-0084

Service Bulletin/Repair Instructions

FORD EDGE 2015: LINCOLN 2015 MKC: BULLETIN INFORMATION INVOLVING VEHICLES EQUIPPED WITH SIRIUS SATELLITE RADIO MAY EXHIBIT AN INTERMITTENT CONCERN IN WHICH THE AUDIO CUTS OUT AND THE RADIO DISPLAYS "NO SIGNAL' MESSAGE WHILE DRIVING. *LJ

ASI-45090

Service Bulletin/Repair Instructions

FORD/LINCOLN: ON SOME VEHICLES, AFTER MODULE PROGRAMMING PROCEDURE OR OTHER ROUTINE SERVICE HAS BEEN PERFORMED, THE MALFUNCTION INDICATOR LAMP WOULD ILLUMINATE DUE TO VARIOUS RESETS OF MODULES. MODEL 2013-16 FUSION, MKZ, 2013-15 C-MAX, 2015 F-150, MKC. *PE

ASI-45125

Service Bulletin/Repair Instructions

LINCOLN: SOME VEHICLES EXPERIENCE NOISE FROM AUDIO SYSTEM WHEN LIFTGATE OR DOOR IS OPEN AND VEHICLES IS INACTIVE, WITH KEY ON OR OFF, FOR 30 MINUTES. MODEL 2015 MKC. *PE

16-0035

Service Bulletin/Repair Instructions

BLIND SPOT INFORMATION SYSTEM (BLIS) - EXTENDED WARNING AFTER OBJECT LEAVES DETECTION AREA - BUILT ON OR BEFORE 4/6/2015 ISSUE Some 2015 MKC vehicles built on or before 4/6/2015 may exhibit a concern with the BLIS warning indicator remaining on longer than one minute after an object leaves the detection area and the detection area remains clear. 1. Does the BLIS warning indicator remain on longer than one minute after an object leaves the detection area and the detection area remains clear? Refer to the Owner's Manual for the detection area. a. Yes - replace the affected side obstacle detection control module (SOD). Refer to Workshop Manual (WSM), Section 419-04. b. No - this article does not apply. Refer to WSM, Section 419-04 for normal diagnostics

TSB160035

Service Bulletin/Repair Instructions

Blind spot infor mation systtem (BLIS) - Extended warning after object leaves detection area - built on or before 04/06/2015

45007

Service Bulletin/Repair Instructions

FORD 2015 EXPEDITION, NAVIGATOR, F-150 W/MYFORD TOUCH OR MY LINCOLN TOUCH: INFORMATION BULLETIN INVOLVING CLIMATE CONTROLLED SEAT BUTTONS. *LJ

45012

Service Bulletin/Repair Instructions

FORD FUSION/MKZ, 2015 MKC, 2015 MUSTANG- BULLETIN REGARDING INTERMITTENTLY, THE STEERING COLUMN CONTROLS FAILS WITH POSSIBLE UO212 IN MULTIPLE MODULES. *LJ

44853

Service Bulletin/Repair Instructions

FORD: ALL 2013-2015 FORD FUSIONS/MKZ, 2015 MUSTANG AND MKC VEHICLES WITH REVERSE PARK AID CAMERA ACTIVE GRIDLINES MAY BE INOPERATIVE AFTER BATTERY DISCONNECT OR COMPONENT SERVICE. *TA

44861

Service Bulletin/Repair Instructions

FORD: SOME 2015 LINCOLN MKC MAY EXPERIENCE THE BATTERY GOING DEAD BECAUSE OF THE WELCOME LIGHT REMAINING ON OR CYCLING ON AND OFF WHEN THE KEYFOB IS LEFT WITHIN DETECTION RANGE OF THE VEHICLE. *TA

TSB-14-0178

Service Bulletin/Repair Instructions

LINCOLN: A FEATURE LOCATED ON SOME VEHICLES, APPROACH DETECTION/WELCOME LIGHTING, FAILS TO WORK AND HAS NO DIAGNOSTIC TROUBLE CODES (DTCS) AND WILL BE INOPERATIVE UNTIL BODY CONTROL MODULE (BCM) IS RESET. MODEL 2015 MKC. *PE

ASI-44702

Service Bulletin/Repair Instructions

LINCOLN: DURING LIGHT THROTTLE TIP, WHILE AT 30 TO 35 MPH, THERE IS A BUMP OR HARSH SHIFT OR HOOT NOISE, AT TIME OF TORQUE CONVERTER CLUTCH BEING APPLIED AND IS NOT DURABILITY OR FUNCTIONAL CONCERN. MODEL 2015 MKC. *PE

ASI-44725

Service Bulletin/Repair Instructions

FORD/LINCOLN: VEHICLE IS EXHIBITING VIBRATIONS WHILE DRIVING AND CAUSE IS BEING ATTRIBUTED TO TIRES AND PROCEDURE IS DRIVE APPROXIMATE 15 MILES TO ELIMINATE ANY FLAT CONDITION AND MISDIAGNOSIS. MODEL 2013-15 ESCAPE, 2015 MKC. *PE

ASI-44737

Service Bulletin/Repair Instructions

LINCOLN: DIAGNOSTIC TROUBLE CODE (DTC) U0415 MAY APPEAR IN POWER STEERING CONTROL MODULE (PSCM) AND RETURN AFTER A SHORT TIME AND CAN BE DISREGARDED UNLESS SPECIFICALLY RELATED TO ELECTRONIC POWER ASSIST STEERING (EPAS) SYSTEM. MODEL 2015 MKC. *PE

ASI-44742

Service Bulletin/Repair Instructions

LINCOLN/FORD: ON SOME VEHICLES, THE INSTRUMENT PANEL CLUSTER (IPC) NEEDS REPLACING DUE TO PROGRAMMABLE MODULE INSTALLATION (PMI) NOT ABLE TO PERFORM. MODEL 2013-14 FUSION, MKZ, 2015 MKC. *PE

ASI-44743

Service Bulletin/Repair Instructions

FORD/LINCOLN: ON SOME VEHICLES, VOLUME WILL GO TO MAXIMUM OR MINIMUM LEVEL WHEN PLUS OR MINUS BUTTON IS PUSHED ON STEERING WHEEL. MODEL 2015 MUSTANG, MKC. *PE

TSB-14-0152

Service Bulletin/Repair Instructions

LINCOLN: NO DIAGNOSTIC TROUBLE CODES (DTC) PRESENT DURING SELF TEST FOR FAILURE OF APPROACH DETECTION/WELCOME LIGHTING FEATURE AND WILL REMAIN INOPERATIVE UNTIL RESETTING OF BODY CONTROL MODULE. MODEL 2015 MKC. *PE

ASI-44677

Service Bulletin/Repair Instructions

FORD/LINCOLN: DIAGNOSTIC TROUBLE CODE (DTC) P025A (FUEL PUMP MODULE A CONTROL CIRCUIT/OPEN) HAS CONCERN OF CRANK NO START OR STALL DUE TO UNPOWERED FUEL PUMP CONTROL MODULE IN TRANSPORT MODE. MODEL 2015 MKC, MKZ, FUSION. *PE

ASI-44687

Service Bulletin/Repair Instructions

LINCOLN: WHEN DRIVING APPROXIMATELY 30-35 MPH, DURING TORQUE CONVERTER LOCK UP, A HOOT NOISE, FROM ENGINE, IS HEARD AND IS NOT A DURABILITY OR FUNCTIONAL CONCERN. MODEL 2015 MKC. *PE

ASI-44688

Service Bulletin/Repair Instructions

LINCOLN: TORQUE CONVERTER WILL CAUSE A HARSH SHIFT OR A BUMP IS FELT AFTER SHIFTING. MODEL 2015 MKC. *PE

ASI-44643

Service Bulletin/Repair Instructions

LINCOLN: A FALSE DIAGNOSTIC TROUBLE CODE U0159 MAY OCCUR DURING DELIVERY OF VEHICLE CONCERNING THE POWER STEERING CONTROL MODULE (PSCM) WITH AN ACTIVE PARK ASSIST AND WILL NOT IMPACT FUNCTION OF ACTIVE PARK ASSIST OR STEERING SYSTEM MODEL 2015 MKC. *PE

ASI-44644

Service Bulletin/Repair Instructions

LINCOLN: SOME VEHICLES ARE EXPERIENCING LOW AIMING HEADLAMP AND PROCEDURE ADJUSTMENTS IS REQUIRED. MODEL 2015 MKC. *PE

ASI-44569

Service Bulletin/Repair Instructions

FORD: DUE TO AN UNPOWERED FUEL PUMP CONTROL MODULE, THE REMOTE START FEATURE WILL EXHIBIT A DIAGNOSTIC TROUBLE CODE (DTC) P025A, WITH CRANK NO START OR STALL, WHILE IN TRANSPORT MODE. MODEL 2015 MKC. *PE

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.