25N17
Other
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Vehicle report
2016 LINCOLN MKX
Service bulletins
207 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 54504
Service Bulletin/Repair Instructions
Some 2016-2017 Edge/MKX, 2017 Continental/Fusion/MKZ vehicles equipped with a 2.7L or 3.0L EcoBoost engine and built on 1-Apr-2016 and through 1-Jan-2017 may exhibit white or blue smoke from the exhaust, rough idle in neutral or park at normal operating temperature or after a hot restart. The vehicle may also exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306 and/or P0316, P0524 and/or P06DD with excessive oil consumption. Oil consumption may be 1 Liter (1 quart) in less than 4,800 km (3,000 miles). This may be due to the valve guides. To correct the condition replace the cylinder heads. During service and repair, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in timing gear failure and engine damage. Replacement of the bolt is critical to the repair. The bolt requires a 4 stage torque procedure. Hold the pulley using a universal holding tool OTC 4754 or equivalent. Refer to Workshop Manual, Section 303-01. The bolt torque procedure can be
TSB 25-2570
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
25E02
Emissions
The affected vehicles have an emissions control system that does not account for certain in-use conditions and might not control tailpipe emissions effectively over time.
SSM 54366
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
TSB 25-2395
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2345 to update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion.
SSM 53174
Service Bulletin/Repair Instructions
Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs. Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.
TSB 24-2345
Service Bulletin/Repair Instructions
Some 2015-2017 Edge, 2016-2017 MKX, 2017 Fusion/MKZ/Continental vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
TSB 24-2165
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
TSB 23-2338
Service Bulletin/Repair Instructions
This article supersedes TSB 22-2181 to update the Service Procedure and Part List. Some 2015-2017 Edge, 2016-2017 MKX, 2017 Fusion/MKZ/Continental vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion. To correct the condition, follow the Service Procedure to replace the valve covers and replace the factory oil pan with a press in place gasket style oil pan.
21B09 S2
Service Bulletin/Repair Instructions
Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit REASON FOR THIS SUPPLEMENT Program Terms & Urgency / Expiration Date: Program extension until July 31, 2023. Service Action: o IDS level 128 or higher is now required to address various programming issues encountered. o C-MAX Energi vehicles are now serviceable with new software and hardware. Labor Allowances: C-MAX labor has been updated. Parts Requirements / Ordering Information: o The C-MAX 4G Upgrade Kit is now orderable at this time with a new part number. o MKX Rear seat backrest nut claim quantity updated. Technical Information updates: o Ensure IDS level 128 or higher is used. o Toggling Valet Mode is no longer required. o C-MAX Energi instructions are now available. Owner Notification: Non-repaired vehicle owners will be mailed the week of April 17, 2023. Pickup and Delivery: Added Customer Acknowledgement Form - Review form contents with customer prior to kit ordering and obtain customer signature prior to installation for Focus BEV, C-MAX, and Fusion Energi vehicles.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 51261
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 51248
Service Bulletin/Repair Instructions
Some 2015-2020 Edge, 2016-2018 MKX, 2019-2020 Nautilus, 2018-2021 Expedition/Navigator, and 2020-2021 Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-2181
Service Bulletin/Repair Instructions
Some 2015-2017 Edge, 2016-2017 MKX, 2017 Fusion/MKZ/Continental vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine vehicles may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
SSM 51120
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
22N02 S1
Service Bulletin/Repair Instructions
Certain 2015-2019 Model Year Edge and Lincoln MKX Vehicles and 2013-2018 Model Year Fusion and Lincoln MKZ Vehicles Front Brake Flexible Hose Replacement REASON FOR THIS SUPPLEMENT Parts Requirements / Ordering Information: Part numbers for Edge and MKX vehicles have been added. Edge and MKX model year updated from 2018 to 2019, build dates remain the same.
22N02
Service Bulletin/Repair Instructions
Certain 2015-2018 Model Year Edge and Lincoln MKX Vehicles and 2013-2018 Model Year Fusion and Lincoln MKZ Vehicles Front Brake Flexible Hose Replacement Submitting Owner Letters
TSB 22-2309
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
21B09-S1
Service Bulletin/Repair Instructions
Certain 2014-2020 Model Year Multiple Vehicle Lines - 3G Telematics Control Unit to 4G Upgrade Kit. The North America 3G cellular service began decommissioning in August 2021 and a complete shutdown of the 3G network took place in February 2022. Vehicles on the road equipped with a 3G telematics control unit (TCU) / embedded modem will lose mobile app functionality/connectivity.
TSB 22-2230
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
SSM 50861
Service Bulletin/Repair Instructions
Some 2015-2016 vehicles equipped with 6F50/6F55 transmission and built on 2-Nov-2015 and through 1-Feb-2016 may exhibit no reverse, 3rd and 5th gear with diagnostic trouble codes (DTCs) P0715,P0717,P0756 and/or P2701. This may be caused by the direct clutch cylinder/tone wheel (7F283) inadvertently forcing the snap ring out of position resulting in damage to the direct clutch hub (7G384). Service part (7J250) complete rotating 3-5-R clutch module is now available. Refer to Workshop Manual (WSM), Section 307-01. For claiming, use causal part 7F283 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) manual.
SSM 50804
Service Bulletin/Repair Instructions
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
TSB 22-2162
Service Bulletin/Repair Instructions
Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
TSB 22-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 50375
Service Bulletin/Repair Instructions
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
SSM 50257
Service Bulletin/Repair Instructions
Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
21B09
Service Bulletin/Repair Instructions
Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit The North America 3G cellular service began decommissioning in August 2021 and will be fully decommissioned in February 2022. Vehicles on the road equipped with a 3G telematics control unit (TCU) / embedded modem will lose mobile app functionality/connectivity. Some owners are still within the *complimentary trial period (depending on model year and brand, see table below) for connected services.
SSM 50175
Service Bulletin/Repair Instructions
Some 2015-2021 Edge, 2016-2018 MKX, and 2019-2021 Nautilus vehicles may exhibit the parking lamps stay on and/or the trailer lights flicker with vehicle turned off when a trailer is connected to the vehicle. This may be due to the software in the trailer module (TRM). To correct the condition, reprogram the TRM with the latest software of the appropriate Ford diagnostic scan tool. Use causal part 19H332 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2322
Service Bulletin/Repair Instructions
This article supersedes TSB 17-0065 to update the Service Procedure and vehicles affected. Some 2015-2019 Edge, 2016-2018 MKX, and 2019 Nautilus vehicles built on or before 05-Jun-2019 may exhibit a rattle or flutter noise from the underbody of the vehicle while moving. This may be due to the movement of loose underbody shield fasteners which are attached to the underbody shields. To correct the condition, follow the Service Procedure to remove the assembly aid fasteners.
SSM 50097
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with a new body control module (BCM) installed may exhibit a programming error when using IDS versions 122.03 through 123.01 stating 'Data Corrupt' or 'Configuration Failed, would you like to retry?'. IDS scan tool version 123.02 contains a fix for this programming error. Install IDS version 123.02 or later from PTS > Rotunda tab > Diagnostic Tool Support > Download Software. Once installed, perform the BCM programmable module installation (PMI). Refer to Workshop Manual (WSM), Section 419-10 > Removal and Installation.
SSM 50067
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50064
Service Bulletin/Repair Instructions
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 50059
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with a new Body Control Module (BCM) installed may exhibit a programming error using IDS v122.03 and newer stating "Data Corrupt" or Configuration Failed, would you like to retry?. A temporary work around has been released to complete the BCM programming process. Uninstall IDS from the computer. Run the IDS clean up utility tool located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Install IDS v122.01 (122_FULL) by copying the following link into an internet address bar https://www.fordservicecontent.com/Ford_Content/IDS/SoftwareUpdates/IDS-122.01_full.exe. Retry the BCM Programmable Module Installation (PMI) using IDS level 122.01. Monitor OASIS for updates.
SSM 50039
Service Bulletin/Repair Instructions
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
TSB 21-2236
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 49931
Service Bulletin/Repair Instructions
Some 2015-2021 Edge, 2016-2018 MKX and 2019-2021 Nautilus vehicles may exhibit a hood bounce or flutter condition at high speeds. This may be due to an incorrect adjustment of the rubber bump stops. To correct this condition, make sure the rubber bump stops are in contact with the inner hood sheet metal. Using a piece of paper between the hood and the rubber hood stop, make sure the paper fits snug with hood closed. For claiming, use causal part number 16612 and applicable labor times from Section 12 of the Service Labor Times Standard (SLTS) Manual.
SSM 49914
Service Bulletin/Repair Instructions
Some 2015-2021 Edge, 2016-2018 MKX, 2019-2021 Nautilus, 2018-2021 Expedition/Navigator, and 2020-2021 Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2175
Service Bulletin/Repair Instructions
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
SSM 49821
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
20R01
Service Bulletin/Repair Instructions
Under Safety Recall 20S15, in some of the affected vehicles, the door latches have a pawl spring tab that may break. This condition will typically prevent the door from latching. If the customer is able to latch the door, after repeated attempts to shut the door, these is a potential the door may unlatch while driving, increasing the risk of injury. Ford's analysis indicates that this condition is more likely to happen in states and territories with high ambient temperatures. For 20R01, owners will be notified that if their vehicle exhibits door latching concerns or if they are concerned about the latches in their vehicles, they may request repairs under this regional program.
SSM 49679
Service Bulletin/Repair Instructions
Some 2015-2020 Edge, 2016-2018 MKX, and 2019-2020 Nautilus vehicles may require replacement of the roof opening panel track or frame for various conditions. When replacing the roof opening panel, the replacement component may have less magnet plates. In order to prevent any noise vibration or harshness (NVH) concerns, the magnets on the headliner around the roof opening panel that line up with the removed magnet plates should be discarded.
SSM 49676
Service Bulletin/Repair Instructions
Some 2021 Mustang Mach-E vehicles may experience a concern of the alarm activating when an unlocked door is opened, the driver door does not unlock/open when pressing the door activation switch, or the door activation switch not lighting up. This may be due to a software configuration in the body control module (BCM). To correct the condition, reprogram the BCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 15604 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49477
Service Bulletin/Repair Instructions
Some 2015-2021 F-150, 2016-2018 MKX, 2019-2021 Nautilus, 2015-2021 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
TSB 20-2373
Service Bulletin/Repair Instructions
2015-2018 Edge, 2016-2018 MKX vehicles equipped with active front steering (AFS) may require additional service when replacing the driver airbag using certain part numbers only and/or if replacing the restraints control module (RCM). In addition, some vehicles may exhibit diagnostic trouble code (DTC) U2300 stored in the RCM if the correct programming procedure was not followed.
SSM 49221
Service Bulletin/Repair Instructions
When installing a replacement short block in 2015-2017 vehicles equipped with a 2.7L or 3.0L EcoBoost engine, the engine must be converted to use a belt driven oil pump with the following parts: left exhaust camshaft JT4Z-6250-B, left intake camshaft - JT4Z-6250-A, belt driven oil pump - KT4Z-6600-A, oil pump belt - JT4Z-6B651-A, crankshaft sprockets - FT4Z-6306-A (x2), crankshaft oil pump belt drive - JT4Z-6306-A. Follow the engine assembly procedure in Workshop Manual (WSM), Section 303-01 using these new parts without installing the chain tensioner or guides as they are not needed with the belt driven oil pump. Fill out the Authorized Modification Label (FPS-8262) with the following text: 'Engine has been modified to use a belt-driven oil pump per SSM XXXXX' and attach it to the underside of the hood.
SSM 49217
Service Bulletin/Repair Instructions
Some 2015-2020 F-150/Mustang, 2016-2020 Edge, 2016-2018 MKX and 2019-2020 Nautilus vehicles built on or before 18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49210
Service Bulletin/Repair Instructions
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 49179
Service Bulletin/Repair Instructions
Some 2015-2020 Edge, 2016-2018 MKX, and 2019-2020 Nautilus vehicles may exhibit the parking lamps stay on and/or the trailer lights flicker with vehicle turned off when a trailer is connected to the vehicle. This may be due to the software in the trailer module (TRM). To correct the condition, reprogram the TRM with the latest software of the appropriate Ford diagnostic scan tool. Use causal part 19H332 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49122
Service Bulletin/Repair Instructions
Some 2015-2020 F-150, 2016-2018 MKX, 2019-2020 Nautilus, 2015-2020 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
TSB 20-2255
Service Bulletin/Repair Instructions
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 48991
Service Bulletin/Repair Instructions
Some 2015-2020 F150/Edge/Fusion, 2016-2018 MKX, 2019-2020 Nautilus, and 2017-2020 Continental vehicles equipped with 2.7L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or knock sensor wiring harness. To correct the condition, replace the 12A648 ECT sensor and 12A699 knock sensor. Do not disconnect the ECT sensor from the knock sensor harness in case parts are called back for analysis. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48908
Service Bulletin/Repair Instructions
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
TSB 20-2171
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 48619
Service Bulletin/Repair Instructions
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
SSM 48423
Service Bulletin/Repair Instructions
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-2390
Service Bulletin/Repair Instructions
Some 2015-2019 F-150, 2015-2020 Explorer, 2017-2019 F-Super Duty, 2017-2020 Continental, 2018-2020 Expedition/Navigator, 2016-2018 MKX, 2019-2020 Nautilus, 2020 Aviator/Corsair and 2013-2020 MKZ vehicles equipped with multi-contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.
SSM 48340
Service Bulletin/Repair Instructions
Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
TSB 19-2332
Service Bulletin/Repair Instructions
Some 2015-2017 Edge, 2016-2017 MKX, 2017 Fusion/MKZ/Continental vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine vehicles may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
TSB 19-2293
Service Bulletin/Repair Instructions
Some 2015-2019 F-150/Explorer, 2017-2019 F-Super Duty/Continental, 2018-2019 Expedition/Navigator, 2016-2018 MKX, 2019 Nautilus, and 2013-2019 MKZ vehicles equipped with Multi-Contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.
SSM 48135
Service Bulletin/Repair Instructions
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
TSB 19-2219
Service Bulletin/Repair Instructions
Some 2015-2017 Edge, 2016-2017 MKX, 2017 Fusion/MKZ/Continental vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine vehicles may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
TSB 19-2243
Service Bulletin/Repair Instructions
Some 2016-2017 Edge/MKX, 2017 Continental/Fusion/MKZ vehicles equipped with a 2.7L or 3.0L EcoBoost engine and built on 1-Apr-2016 and through 1-Jan-2017 may exhibit white or blue smoke from the exhaust, rough idle in neutral or park at normal operating temperature or after a hot restart. The vehicle may also exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306 and/or P0316, P0524 and/or P06DD with excessive oil consumption. Oil consumption may be 1 Liter (1 quart) in less than 4,800 km (3,000 miles). This may be due to the valve guides. To correct the condition, follow the Service Procedure to replace the cylinder heads.
SSM 48130
Service Bulletin/Repair Instructions
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
SSM 48108
Service Bulletin/Repair Instructions
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 48053
Service Bulletin/Repair Instructions
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
SSM 48049
Service Bulletin/Repair Instructions
Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-2198
Service Bulletin/Repair Instructions
Some 2016-2018 MKX and 2019 Nautilus vehicles may exhibit a wind or whistle noise from the exterior mirror(s) at highway speed. This may be due to the spacing between the exterior mirror base and the mirror cover. To correct the condition, follow the Service Procedure steps to add foam to the back of the mirror cover for the affected side(s).
SSM 47993
Service Bulletin/Repair Instructions
2015-2016 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Taurus Police/Explorer/Explorer Police vehicles built on or before 10-Jun-2016 and equipped with a 3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) may exhibit a PTU venting, an odor originating from the PTU, or noise originating from the PTU. These vehicles may be a candidate for rebuild using PTU Idler Gear/Shaft/Bearing Kit (GB5Z-7P258-A). Refer to Workshop Manual (WSM), Section 308-07.
SSM 47976
Service Bulletin/Repair Instructions
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 47967
Service Bulletin/Repair Instructions
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 47960
Service Bulletin/Repair Instructions
Some 2016 MKX vehicles may exhibit a missing drive control menu if the instrument panel cluster (IPC) is replaced using the current service part. If a IPC replacement is not urgent, advise the customer that Engineering is aware of the issue and working on releasing a service IPC for the 2016 MKX with enabled drive control menu feature. Monitor OASIS for updates.
SSM 47850
Service Bulletin/Repair Instructions
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 47948
Service Bulletin/Repair Instructions
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 47922
Service Bulletin/Repair Instructions
SSM 47922 - Various Vehicles - 2.7L/3.0L EcoBoost Engine - Oil Filter Service Tip When servicing the oil filter on vehicles equipped with a 2.7L or 3.0L EcoBoostengine it is critical to inspect the oil filter housing center stem to verify is not separated or damaged. If the center stem is damaged or separated from the housing this will result in oil flow through the reservoir drain port causing low engine oil pressure and internal engine damage. If the filter housing stem is damaged or separated, the oil filter housing must be replaced. If the center stem is not damaged or separated, the O-ring seals on the stem and housing must be replaced each time the filter is serviced.
SSM 47854
Service Bulletin/Repair Instructions
Some 2017-2019 F-Super Duty, 2017-2019 Continental, 2016-2019 Edge, 2016-2018 MKX, 2019 Nautilus vehicles may exhibit a U3000:49 diagnostic trouble code (DTC) setting in the Steering Effort Control Module (SECM) with no other DTCs present. To eliminate the DTC, perform the IDS SASM module reset routine. The IDS reset routine is available under Toolbox > Chassis > Steering > Adaptive Front Steering > SASM Module Reset. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. For claiming, use causal part 3600 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47824
Service Bulletin/Repair Instructions
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
19B04-S1
Service Bulletin/Repair Instructions
Certain 2015-2016 Model Year Edge and 2016 Model Year MKX Vehicles Equipped with Adaptive Steering - Steering Wheel Replacement
SSM 47814
Service Bulletin/Repair Instructions
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
19B04
Service Bulletin/Repair Instructions
Certain 2015-2016 Model Year Edge and 2016 Model Year MKX Vehicles Equipped with Adaptive Steering - Steering Wheel Replacement
TSB 19-2026
Service Bulletin/Repair Instructions
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
SSM 47791
Service Bulletin/Repair Instructions
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-2017
Service Bulletin/Repair Instructions
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
SSM 47749
Service Bulletin/Repair Instructions
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
TSB 18-2378
Service Bulletin/Repair Instructions
Some 2015-2019 Edge, 2016-2018 MKX, and 2019 Nautilus vehicles equipped with all wheel drive (AWD) may exhibit a fuel slosh noise primarily when the fuel tank is over 3/4 full and when driving at low speeds. This may be due to the fuel moving around in the fuel tank. Follow the Service Procedure steps to correct the condition.
SSM 47711
Service Bulletin/Repair Instructions
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
TSB 18-2361
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 47662
Service Bulletin/Repair Instructions
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 47635
Service Bulletin/Repair Instructions
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 47638
Service Bulletin/Repair Instructions
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
SSM 47538
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
SSM 47489
Service Bulletin/Repair Instructions
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
TSB 18-2255
Service Bulletin/Repair Instructions
Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
SSM 47444
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47446
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV and clean the engine sealing surface using only Motorcraftù Metal Brake Parts Cleaner, then wipe with Motorcraftù Metal Surface Prep Wipes and allow to air dry. Refer to WSM, Section 303-00 > RTV Sealing Surface Cleaning and Preparation. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Skipping or improperly completing steps may result in repeat oil pan leaks.
SSM 47379
Service Bulletin/Repair Instructions
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47380
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47344
Service Bulletin/Repair Instructions
Some 2016 MKX and 2017 Continental/MKZ vehicles equipped with a Revel Ultima audio system may exhibit a loud screeching/squealing noise from the speakers when the audio system is on or off. To determine if the vehicle is equipped with a Revel Ultima audio system access the window sticker through the Historical Vehicle Bill of Materials on the Professional Technician Society Website. Under optional equipment the audio system will show up as Revel Ultima, Revel Ultimate, or Revel II Audio. To correct the condition, program the digital signal processing (DSP) module to the latest calibration using IDS version 102.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest calibration. Use causal part 18B849 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) manual.
SSM 47265
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engines may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan by performing the published Workshop Manual (WSM) service procedures. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV, clean the engine sealing surface with only Motorcraftù Metal Brake Parts Cleaner then wipe with Motorcraftù Metal Surface Prep Wipes, and allow to air dry as directed in WSM, Section 303-00, RTV Sealing Surface Cleaning and Preparation. If possible, after the new oil pan is installed, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Ford is investigating this concern. Monitor OASIS for future updates.
SSM 47251
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2016-2018 MKX vehicles may exhibit a concern with the remote start selections for heated steering wheel and/or heated seats grayed out in the cluster. To correct this concern, reconfigure the front controls interface module (FCIM) using As-Built Programming. Make sure you are connected to the internet when entering module programming to obtain the latest data. If the concern is still present, refer to Workshop Manual (WSM), Section 501-10A for the directed self-test for the FCIM. For claiming, use causal part 18842 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
SSM 47235
Service Bulletin/Repair Instructions
Some 2016 Edge/MKX vehicles may exhibit an illuminated adaptive/active steering fault message in the instrument panel cluster (IPC) message center with diagnostic trouble codes (DTCs) U3000, C2003, B137F, B1380, U210A, and U2000 stored in the SECM. If these DTCs are present, replace the SECM. Use causal part 3600 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47230
Service Bulletin/Repair Instructions
Some 2007-2016 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Police Interceptor Sedan/Explorer/Police Interceptor Utility vehicles equipped with AWD and built on or before 30-Jun-2016 may exhibit a propane or natural gas odor during idle or low speed driving. This may be due to break down of the power transfer unit (PTU) fluid caused by excessive heat. If the source of the odor is identified as originating from the PTU, an idler bearing repair kit is available to repair the PTU. Refer to the Workshop Manual (WSM), Section 308-07. If the PTU is determined to be repairable, utilize kit GB5Z-7P258-A and the included instruction sheet. For claiming use causal part 7P258 and applicable labor operations in section 07 of the Service Labor Time Standards (SLTS) Manual.
SSM 47211
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47201
Service Bulletin/Repair Instructions
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
SSM 47205
Service Bulletin/Repair Instructions
Some 2016-2018 MKX vehicles equipped with an intrusion sensor, built on or before 22-Feb-2018, may exhibit an inability to disable the intrusion sensor through the cluster alarm menu under vehicle settings. This may be due to a missing instrument panel cluster (IPC) menu selection to allow the intrusion sensor to be disabled. Reconfigure the IPC module using As-Built Programming. Make sure you are connected to the internet when entering module programming to obtain the latest data. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47171
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.
SSM 47167
Service Bulletin/Repair Instructions
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47159
Service Bulletin/Repair Instructions
Some 2016 MKC, MKX and MKZ vehicles built on or before 11/28/2015 and equipped with a TCU may exhibit an intermittent battery draw that can be isolated to the TCU, an inoperative MyLincoln Mobile app, a MyLincoln Mobile app deep sleep message, an inaccurate MyLincoln Mobile app oil life message, an incorrect MyLincoln Mobile app fuel level, a MyLincoln Mobile app false low tire warning and/or Diagnostic Trouble Codes U2100 and/or U2101 stored in the TCU. To correct the condition, program the TCU to the latest calibration using IDS version 108.06 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest calibration. For warranty claiming, use causal part 14G229 and applicable labor operations in the SLTS Manual, Section 10.
SSM 47160
Service Bulletin/Repair Instructions
Some 2015-2017 MKC/MKZ, 2016-2017 MKX and 2017 Continental vehicles equipped with a Telematics Control Unit (TCU) built on or before 15-Aug-2017 may exhibit inoperative remote features via Lincoln Way Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU Field Service Actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.06 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
SSM 47144
Service Bulletin/Repair Instructions
Some 2016 MKX vehicles equipped with a Heated Steering Wheel built on or before 12/2/2015 may exhibit a condition where the heated steering wheel icon is missing from the MyLincoln Touch 8" touch screen. To determine if the vehicle is equipped with a heated steering wheel, refer to the window sticker which can be accessed through HVBOM. To correct the condition, follow the SYNC Module APIMÙ Standard Programming procedure outlined in section 415-00 of the online Workshop Manual. For claiming, use causal part 14D212 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual
SSM 47100
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln Vehicle equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.
TSB18-2057
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2016-2018 MKX vehicles may exhibit an exhaust odor in the vehicle while the climate control system is in auto or recirculation mode. Customers may indicate the odor smells like sulfur or exhaust odors are entering the vehicle cabin. This concern may be more pronounced after hard acceleration, driving in hilly conditions and/or towing a trailer. Whether and to what extent any occupant of these vehicles experiences the exhaust odor will be affected by driving habits, weather, and individual sensitivities. Follow the Service Procedure steps to correct the condition.
TSB18-2055
Service Bulletin/Repair Instructions
Some 2015-2017 Edge vehicles built on or before 10-Aug-2017 and 2016-2018 MKX vehicles built on or before 15-Dec-2017, equipped with a power liftgate and the hands-free liftgate activation feature may exhibit the liftgate opening or closing when a rear door is slammed shut, or the rear fascia is contacted such as kneeling or resting a foot on the fascia while the key is present. Follow the Service Procedure steps to correct the condition.
SSM 47080
Service Bulletin/Repair Instructions
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
SSM 47070
Service Bulletin/Repair Instructions
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
TSB18-2042
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2016-2018 MKX vehicles equipped with a power liftgate and built on or before 2-Jan-2018 may exhibit an intermittent bounce back after closing has been commanded. Follow the Service Procedure steps to correct this condition.
SSM 47041
Service Bulletin/Repair Instructions
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47000
Service Bulletin/Repair Instructions
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 46947
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 46948
Service Bulletin/Repair Instructions
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
SSM 46949
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 46930
Service Bulletin/Repair Instructions
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
17-2235
Service Bulletin/Repair Instructions
Some 2016-2017 Edge/MKX, 2017 Continental, and 2017 Fusion/MKZ vehicles equipped with a 2.7L or 3.0L gasoline turbocharged direct injection (GTDI) engine and built on 1-Apr-2016 and through 1-Jan-2017 may exhibit white or blue smoke from the exhaust, rough idle in neutral or park at normal operating temperature or after a hot restart. The vehicle may also exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306 and/or P0316, P0524 and/or P06DD with excessive oil consumption. Oil consumption may be 1 Liter (1 quart) in less than 4,800 km (3,000 miles). Follow the Service Procedure steps to correct the condition.
SSM 46920
Service Bulletin/Repair Instructions
Some 2016-2018 MKX customers may report that a deployed cargo cover will inadvertently recoil after the vehicle hits a bump. Revised Cargo covers are available to address this issue. Use the vehicle identification number (VIN) to select the interior trim color of the vehicles; FA1Z- 5845440-AG(Ebony), FA1Z- 5845440-AH (Coffee), FA1Z-5845440-BG (Ebony Black Label), FA1Z- 5845440-BH (Espresso Black Label), FA1Z-5845400-BJ (Rouge Noir).
SSM 46906
Service Bulletin/Repair Instructions
Some 2015-2018 F150/Edge, 2016-2018 MKX and 2017-2018 Fusion, Continental vehicles equipped with a 2.7L engine may experience a malfunction indicator lamp (MIL) and/or wrench lamp with Diagnostic Trouble Codes (DTCs): P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. If an issue with the wiring is found use causal part 12A699.
SSM 46860
Service Bulletin/Repair Instructions
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
SSM 46861
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
tsb17-2198
Service Bulletin/Repair Instructions
Some 2015-2017 Edge and 2016-2017 MKX vehicles, equipped with a power liftgate, and built on or before 13-Sep-2017 may exhibit a liftgate that intermittently opens uncommanded while parked with no keys near the vehicle. Follow the Service Procedure steps to correct this condition.
SSM 46848
Service Bulletin/Repair Instructions
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
SSM 46834
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
TSB 17-0065
Service Bulletin/Repair Instructions
Some 2015-2017 Edge and 2016-2017 MKX vehicles built on or before 15-Apr-2017 and 2017 Continental vehicles built on or before 19-Oct-2016 may exhibit a rattle noise from the underbody of the vehicle while moving. This may be due to the movement of loose floor pan underbody shield fasteners which are attached to the underbody shields. Follow the Service Procedure steps to correct the condition.
SSM 46813
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.
SSM 46703
Service Bulletin/Repair Instructions
Some 2013-2017 Edge/MKX/Escape/MKC/Fusion/MKZ/Flex/MKT/Mondeo/Kuga/EcoSport AWD vehicles where diagnosis leads to a RDU clutch issue, a rear drive unit (RDU) service kit is available. Use the vehicle identification number (VIN) in the parts catalog to look for base part 4A232. If clutch assembly (base 4A232) is not listed in the catalog, this message does not apply. For vehicle repairs refer to updated Workshop Manual (WSM), Section 205-02 on ATC clutch repairs. Use causal part 4A232 or equivalent and applicable labor operations.
TSB 17-2068
Service Bulletin/Repair Instructions
Some 2016-2017 Edge, Escape, Expedition, Fiesta, Flex, MKC, MKT, MKX, Mustang, Navigator and Taurus or 2017 Explorer and Super Duty vehicles equipped with SYNC 3 and built on 1-Jul-2015 and through 31-Dec-2016 may exhibit a SYNC display message of Please check your surroundings for safety along with no rear view camera image when in reverse gear. This will occur only at ambient temperatures ranging from -5 Å'C to 5 Å'C (23 Å'F to 41 Å'F). This maybe due to a temperature dependent issue within the APIM crystal oscillator circuitry. Follow the Service Procedure steps to correct the condition.
SSM 46522
Service Bulletin/Repair Instructions
2013-2017 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Taurus Police/Explorer/Explorer Police/Continental vehicles equipped with a 3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) that is being repaired or replaced for an internal failure must also have the vent hose replaced due to contamination in the hose.
TSB 17-0035
Service Bulletin/Repair Instructions
SOME 2015-2017 EDGE AND 2016-2017 MKX VEHICLES MAY EXHIBIT AN EXHAUST ODOR IN THE VEHICLE WHILE THE CLIMATE CONTROL SYSTEM IS IN AUTO OR RECIRCULATION MODE. CUSTOMERS MAY INDICATE THE ODOR SMELLS LIKE SULFUR, THE EXHAUST ODORS ARE ENTERING THE VEHICLE CABIN. THIS CONCERN MAY BE MORE PRONOUNCED AFTER HARD ACCELERATION, DRIVING IN HILLY CONDITIONS AND/OR TOWING A TRAILER. WHETHER AND TO WHAT EXTENT ANY OCCUPANT OF THESE VEHICLES EXPERIENCES THE EXHAUST ODOR WILL BE AFFECTED BY DRIVING HABITS, WEATHER, AND INDIVIDUAL SENSITIVITIES. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46486
Service Bulletin/Repair Instructions
SOME 2016-2017 FORD OR LINCOLN VEHICLES EQUIPPED WITH SYNC 3 MAY EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
SSM 46481
Service Bulletin/Repair Instructions
SOME 2016 AND 2017 EDGE/MKX VEHICLES EQUIPPED WITH LANE KEEPING SYSTEM, ADAPTIVE STEERING, AND BUILT ON OR BEFORE 01-FEB-2017 MAY EXHIBIT AN INOPERATIVE LANE KEEPING SYSTEM. IF THE VEHICLE EXHIBITS THIS CONCERN, REPROGRAM THE SECM TO THE LATEST SOFTWARE LEVEL USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 104.04 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN DOWNLOADING AS-BUILT DATA. FOR CLAIMING, USE CAUSAL PART 3504 AND APPLICABLE LABOR OPERATIONS IN SECTION 3 OR 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
TSB 17-0030
Service Bulletin/Repair Instructions
SOME 2016-2017 MKX VEHICLES MAY EXHIBIT ONE OR BOTH REAR DOORS THAT ARE HARD TO OPEN IN FREEZING TEMPERATURES. THIS MAY BE DUE TO WATER ENTERING AND FREEZING THE REAR DOOR EXTERIOR LATCH CABLE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46438
Service Bulletin/Repair Instructions
SOME 2016-2017 F150, EDGE, MKX, ESCAPE, FOCUS, MKC, FUSION, MKZ, TAURUS AND 2017 CONTINENTAL VEHICLES EQUIPPED WITH 2.0L, 2.7L OR 3.0L GASOLINE TURBOCHARGED DIRECT INJECTION(GTDI) ECOBOOST ENGINES MAY EXHIBIT MALFUNCTION INDICATOR LIGHT(MIL) ON WITH DIAGNOSTIC TROUBLE CODES(DTC) P1013, P1015 AND/OR P1016 STORED IN POWERTRAIN CONTROL MODULE(PCM). CHECK TURBOCHARGER WASTEGATE CONTROL HOSES FOR WATER/ICE RESTRICTIONS OR PINCHING AT ZIP-TIE ON ENGINE CAM COVER RETAINER(2.7L AND 3.0L ONLY). IF RESTRICTION IS FOUND ON CAM COVER RETAINER, CUT ZIP TIE AND CLEAR DTCS. IF WATER/ICE RESTRICTION IS FOUND, DRAIN HOSES, REASSEMBLE AND CLEAR DTCS. IF DTCS RETURN, REFER TO WORKSHOP MANUAL (WSM) OR POWERTRAIN CONTROL EMISSIONS DIAGNOSIS (PCED) MANUAL FOR NORMAL DIAGNOSTICS. ENGINEERING IS INVESTIGATING THE CONCERN, MONITOR OASIS FOR FURTHER UPDATES.
SSM 46412
Service Bulletin/Repair Instructions
SOME 2007-2016 EDGE/MKX/FLEX/MKT/MKZ/MKS/TAURUS/TAURUS POLICE/EXPLORER/EXPLORER POLICE EQUIPPED WITH ALL WHEEL DRIVE (AWD) AND BUILT ON OR BEFORE 30-JUN-2016 MAY EXHIBIT A TICKING AND/OR KNOCKING NOISE COMING FROM THE DRIVELINE AREA. TO IDENTIFY THIS NOISE, REFER TO WORKSHOP MANUAL (WSM), SECTION 100-04, AND FOLLOW THE SYMPTOM CHART. IF THE SOURCE OF THE NOISE IS IDENTIFIED AS THE PTU AND/OR INTERNAL TO THE PTU, DISASSEMBLE PTU ASSEMBLY. REFER TO UPDATED WSM, SECTION 308-07. IF THE PTU IS DETERMINED TO BE REPAIRABLE, UTILIZE KIT GB5Z-7P258-A AND THE INCLUDED INSTRUCTION SHEET. FOR CLAIMING, USE CAUSAL PART 7P258 AND APPLICABLE LABOR OPERATIONS IN SECTION 07 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46371
Service Bulletin/Repair Instructions
SOME 2012-2017 FOCUS ELECTRIC/2013-2017 CMAX ENERGI/FUSION ENERGI/2015-2017 MKC/MKZ/2016-2017 MKX AND 2017 CONTINENTAL VEHICLES OPERATING WITH A 3G TCU ON OR BEFORE 16-JAN-2017 MAY NOT RESPOND TO CUSTOMERS REMOTE COMMANDS VIA MYLINCOLN/MYFORD MOBILE PHONE APPLICATIONS. 2G NETWORKS WERE DECOMMISSIONED ON 16-JAN-2017. IF THE 3G TCU WAS OPERATING ON A 2G NETWORK, IT WILL NOT AUTOMATICALLY ATTEMPT TO RECONNECT TO THE REPLACEMENT 3G NETWORK. TO CORRECT, RESET THE TCU BY REMOVING ITS POWER FUSE FOR 5 MINUTES. IF THE CONCERN IS STILL PRESENT, FOLLOW NORMAL DIAGNOSTICS IN WORKSHOP MANUAL (WSM), SECTION 415-00. REFER TO PTS OASIS HOME PAGE FOR TCU VERSION IDENTIFICATION. FOR CLAIMING, USE CAUSAL PART 14G229 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46363
Service Bulletin/Repair Instructions
SOME 2016 EDGE/MKX VEHICLES EQUIPPED WITH A 2.7L ENGINE AND BUILT ON 1-APR-2016 AND THROUGH 1-OCT-2016 MAY EXHIBIT A ROUGH IDLE IN NEUTRAL OR PARK AT NORMAL OPERATING TEMPERATURE OR AFTER A HOT RESTART, WHITE OR BLUE SMOKE FROM THE EXHAUST, EXCESSIVE OIL CONSUMPTION AND/OR AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0300, P0301, P0302, P0303, P0304, P0305, P0306 AND/OR P0316. SUSPECT THE CYLINDER HEADS AS THE CAUSE FOR THIS ISSUE. IF THE VEHICLE ALSO EXHIBITS P0524 AND/OR P06DD SUSPECT THE LONG BLOCK AS THE CAUSE FOR THIS ISSUE.
SSM 46355
Service Bulletin/Repair Instructions
MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46341
Service Bulletin/Repair Instructions
WHEN SERVICING A 2.7L OR 3.0L ECOBOOST ENGINE, IF THE CRANKSHAFT PULLEY IS REMOVED, CORRECT REASSEMBLY IS CRITICAL TO PREVENT POTENTIAL ENGINE FAILURE. THIS INCLUDES INSTALLING A NEW CRANKSHAFT PULLEY BOLT AND ACCURATELY PERFORMING EACH STAGE OF THE CRANKSHAFT PULLEY BOLT TORQUE SEQUENCE. CRANKSHAFT PULLEY RELATED WORKSHOP MANUAL (WSM) PROCEDURE AND RECOMMENDED TOOL (OTC 4754 OR EQUIVALENT) INFORMATION HAVE BEEN UPDATED. REFER TO THE APPLICABLE WSM, SECTION 303-01, FOR ADDITIONAL INFORMATION.
17B01
Service Bulletin/Repair Instructions
CERTAIN 2016 MODEL YEAR LINCOLN MKX VEHICLES - REMOTE TRANSCEIVER MODULE REPROGRAMMING
SSM 46332
Service Bulletin/Repair Instructions
REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.
SSM 46320
Service Bulletin/Repair Instructions
SOME 2016-2017 MKX VEHICLES EQUIPPED WITH A FRONT VIEW CAMERA AND BUILT ON OR BEFORE 25-NOV-2016 MAY EXHIBIT A FRONT VIEW CAMERA THAT STAYS DEPLOYED IN PARK, IS SLOW TO RETRACT WHEN SHIFTED TO NEUTRAL, DEPLOYS WHEN SHIFTING FROM PARK TO DRIVE OR DRIVE TO PARK, AND/OR DEPLOYS DURING A REMOTE START. TO CORRECT THE CONDITION, UPDATE THE IMAGE PROCESSING MODULE B (IPM-B) TO THE LATEST LEVEL CALIBRATION USING IDS VERSION 103.05 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR CLAIMING, USE CAUSAL PART 19H405 AND APPLICABLE LABOR OPERATION(S) IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46295
Service Bulletin/Repair Instructions
TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
SSM 46279
Service Bulletin/Repair Instructions
SOME 2016 MKX VEHICLES EQUIPPED WITH CLIMATE CONTROL SEATS AND BUILT ON OR BEFORE 3-OCT-2016 MAY EXHIBIT POOR COOLING PERFORMANCE FROM THE CLIMATE CONTROL SEAT. TO CORRECT THE CONDITION, UPDATE THE SEAT CONTROL MODULE E (SCME) AS-BUILT CONFIGURATION USING IDS VERSION 103.01 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN DOWNLOADING THE UPDATED AS-BUILT DATA. FOR CLAIMING, USE CAUSAL PART 19N550 AND APPLICABLE LABOR OPERATION(S) IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46281
Service Bulletin/Repair Instructions
SOME 2015-2017 EDGE/MKX, ESCAPE/MKC, FUSION/MKZ AND EXPLORER VEHICLES EQUIPPED WITH A 2.0L OR 2.3L MAY EXHIBIT DAMAGE TO THE ENGINE APPEARANCE COVER, VALVE COVER AND/OR INTAKE MANIFOLD WHEN ATTEMPTING TO REMOVE THE APPEARANCE COVER. TO REDUCE THE POSSIBILITY OF DAMAGE, CAREFULLY PULL STRAIGHT UPWARD ON THE UNDERSIDE OF THE COVER AT EACH FASTENER LOCATION TO REMOVE. DO NOT PULL THE COVER FORWARD OR TO THE SIDE. BEFORE INSTALLING THE ENGINE APPEARANCE COVER, APPLY MOTORCRAFT SILICONE BRAKE CALIPER GREASE AND DIELECTRIC COMPOUND (XG-3-A) TO THE COVER FASTENER GROMMETS. WORKSHOP MANUAL (WSM) INFORMATION IS IN THE PROCESS OF BEING UPDATED
SSM 46283
Service Bulletin/Repair Instructions
SOME OWNERS OF 2016 FORD AND LINCOLN MKX VEHICLES EQUIPPED WITH SYNC 3 MAY INQUIRE ABOUT UPGRADING TO APPLE CARPLAY AND ANDROID AUTO. THIS UPGRADE IS NOT CURRENTLY AVAILABLE FOR THOSE VEHICLES. APPLE CARPLAY AND ANDROID AUTO ARE CURRENTLY AVAILABLE ONLY ON VEHICLES EQUIPPED WITH SYNC 3 V2.0 OR LATER. THIS UPGRADE FOR 2016 FORD AND LINCOLN MKX VEHICLES WILL BE AVAILABLE IN 2017. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.
TSB 16-2085
Service Bulletin/Repair Instructions
SOME 2015-2016 EDGE AND 2016 MKX VEHICLES BUILT ON OR BEFORE 9-SEP-2016 MAY EXHIBIT A LEFT SIDE REAR SEAT BACKREST THAT WILL NOT FOLD TO LESS THAN 45 DEGREES FROM THE FLOOR ON ITS OWN WHEN UNLATCHING THE SEAT BACKREST USING THE SECOND ROW SEAT CONTROL SWITCH OR SECOND ROW SEAT BACKREST RECLINE HANDLE. THIS IS CAUSED BY EXCESSIVE RESISTANCE BETWEEN THE REAR SEAT BACKREST FRAME AND REAR SEAT RISER FRAME. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46210
Service Bulletin/Repair Instructions
SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.
TSB 16-2066
Service Bulletin/Repair Instructions
SOME 2016 EDGE/MKX VEHICLES EQUIPPED WITH ADAPTIVE/ACTIVE STEERING MAY EXHIBIT A CHECK ADAPTIVE/ACTIVE STEERING MESSAGE ILLUMINATED IN THE INSTRUMENT PANEL CLUSTER (IPC) MESSAGE CENTER WITH DIAGNOSTIC TROUBLE CODE (DTC) C1B00 STORED IN THE STEERING EFFORT CONTROL MODULE (SECM). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46171
Service Bulletin/Repair Instructions
SOME 2016 EDGE/MKX VEHICLES MAY EXHIBIT AN ILLUMINATED ADAPTIVE/ACTIVE STEERING FAULT MESSAGE IN THE INSTRUMENT PANEL CLUSTER (IPC) MESSAGE CENTER WITH DIAGNOSTIC TROUBLE CODES (DTCS) U3000, C2003, B137F, B1380, U210A, AND U2000 STORED IN THE SECM. IF DTC U3000:96 IS PRESENT, THE SECM MUST BE REPLACED. IF DTC U3000:96 IS NOT PRESENT, REPROGRAM THE SECM TO THE LATEST CALIBRATION USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 102.05 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART 3600 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46172
Service Bulletin/Repair Instructions
SOME 2015-2017 F-150, 2016 MKX, 2015 EDGE, 2017 FUSION, MKZ AND CONTINENTAL VEHICLES EQUIPPED WITH A 2.7L/3.0L ENGINE MAY APPEAR TO HAVE LOW ENGINE OIL LEVEL IF THE PROPER PROCEDURES ARE NOT FOLLOWED. REFER TO THE OWNERS GUIDE, MAINTENANCE, ENGINE OIL CHECK SECTION. WHEN CHECKING THE ENGINE OIL LEVEL AFTER SHUTTING OFF THE ENGINE WAIT AT LEAST 15 MINUTES PRIOR TO CHECKING IN ORDER TO ALLOW THE OIL TO DRAIN BACK TO THE OIL PAN. THE ENGINE OIL LEVEL CAN BE CHECKED IMMEDIATELY IF THE ENGINE HAS NOT BEEN STARTED. WHEN CHANGING THE ENGINE OIL THE ENGINE NEEDS TO BE AT NORMAL OPERATING TEMPERATURE AND THE OIL FILTER REMOVED BEFORE DRAINING THE OIL. ALLOW THE OIL PAN TO DRAIN COMPLETELY FOR UP TO 5 MINUTES. CHECK OIL LEVEL AFTER FILLING BY FOLLOWING THE OIL LEVEL CHECK PROCEDURE.
16B32-S1
Service Bulletin/Repair Instructions
CERTAIN 2015 MODEL YEAR EDGE, 2015-2016 MODEL YEAR F-150, MKT, AND POLICE INTERCEPTOR SEDAN, AND 2016 MODEL YEAR ESCAPE, EXPLORER, FLEX, FUSION, MKX, MUSTANG, POLICE INTERCEPTOR UTILITY, TAURUS, AND TRANSIT VEHICLES - ELECTRONIC THROTTLE BODY REPLACEMENT
SSM 46151
Service Bulletin/Repair Instructions
SOME 2016-2017 FORD AND LINCOLN VEHICLES EQUIPPED WITH SYNC 3 AND NAVIGATION MAY EXHIBIT A CONDITION IN WHICH THE SIRIUSXM TRAFFIC LISTING IS NOT LOADING BUT ALL REMAINING TRAVEL LINK FEATURES OPERATE PROPERLY. SIRIUSXM TRAFFIC IS ONLY AVAILABLE ON VEHICLES EQUIPPED WITH NAVIGATION, ONLY IN SELECT MARKETS AND REQUIRES AN ACTIVE SUBSCRIPTION TO SIRIUSXM TRAFFIC INFORMATION. IF SIRIUSXM TRAFFIC WILL NOT LOAD ATTEMPT THE FOLLOWING PROCEDURE. TURN THE IGNITION OFF, OPEN AND CLOSE THE DRIVERS DOOR, WAIT FOR 3 MINUTES, THEN DRIVE THE VEHICLE OUTSIDE TO OBTAIN A CLEAR VIEW OF THE SKY. SIRIUSXM TRAFFIC SHOULD RECOVER. IF SIRIUSXM TRAFFIC DOES NOT RECOVER CONTINUE TO MONITOR OASIS FOR FUTURE UPDATES. ENGINEERING IS AWARE OF THIS CONCERN AND NO COMPONENT REPLACEMENT OR ANY SOFTWARE RE-FLASHES SHOULD BE PERFORMED AT THIS TIME. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
SSM 46153
Service Bulletin/Repair Instructions
SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.
SSM 46155
Service Bulletin/Repair Instructions
SOME 2015-2017 MKC, 2016 MKX, AND 2016-2017 MKZ VEHICLES EQUIPPED WITH A TELEMATICS CONTROL UNIT (TCU) BUILT ON OR BEFORE 19-OCT-2016 MAY EXHIBIT LOSS OF FUNCTIONALITY OF REMOTE FEATURES VIA THE MYLINCOLN MOBILE APPLICATION. TO CORRECT THE CONDITION, PROGRAM THE TCU TO THE LATEST CALIBRATION USING IDS VERSION 102.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST CALIBRATION. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR 2015 MKC/MKZ VEHICLES MAKE SURE FSA 15N04 HAS BEEN COMPLETED PRIOR TO ATTEMPTING REPROGRAMMING. IF FSA 15N04 HAS BEEN COMPLETED AND THE TCU IS AT THE LATEST CALIBRATION, THEN REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSTICS. USE CAUSAL PART 14G229 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL
SSM 46132
Service Bulletin/Repair Instructions
SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.
SSM 46129
Service Bulletin/Repair Instructions
SOME 2013-2016 FUSION/ESCAPE/MKT/FLEX/MKS/TAURUS, 2015-2016 MKZ/MKC/EDGE AND 2016 MKX VEHICLES MAY EXHIBIT VARIOUS RADIO CONCERNS INCLUDING: SPEAKER STATIC WITH KEY-OFF, NO AUDIO AFTER VEHICLE IS FIRST STARTED WITH DIAGNOSTIC TROUBLE CODE (DTC) U0184, NO VOLUME CONTROL, OR A STUCK CD WITH NO SLOT BLOCKAGE. PRIOR TO STARTING NORMAL DIAGNOSIS FOR ANY OF THESE CONDITIONS, VERIFY THE ACM IS AT THE LATEST CALIBRATION USING IDS VERSION 102.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE THE APPLICABLE LABOR OPERATION IN SECTION 11 OF THE SLTS MANUAL AND CAUSAL PART 18C869 WHEN CLAIMING THIS REPAIR.
SSM 46118
Service Bulletin/Repair Instructions
WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.
TSB 16-0139
Service Bulletin/Repair Instructions
SOME 2015-2016 F-150, C-MAX, EDGE, MKS, TAURUS, AND FLEX AND 2016 EXPEDITION, EXPLORER, ESCAPE, FUSION, MUSTANG, MKZ, MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
TSB 16-0138
Service Bulletin/Repair Instructions
SOME 2016 MKX VEHICLES EQUIPPED WITH A 2.7L ENGINE AND 6F50/6F55 TRANSMISSION MAY EXHIBIT A BUZZ, HUM OR MOAN NOISE FROM THE ENGINE COMPARTMENT AT 40 KPH (25 MPH) AND ABOVE OR AT ENGINE SPEEDS FROM 2000 TO 3500 RPM. THIS MAY BE DUE TO THE TRANSMISSION FLUID COOLER TUBE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46102
Service Bulletin/Repair Instructions
Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
SSM 46103
Service Bulletin/Repair Instructions
Some 2016 MKX and 2017 Continental/MKZ vehicles equipped with a Revel Ultima audio system may exhibit a loud screeching/squealing noise from the speakers when the audio system is on or off. To determine if the vehicle is equipped with a Revel Ultima audio system access the window sticker through the Historical Vehicle Bill of Materials on the Professional Technician Society Website. Under optional equipment the audio system will show up as Revel Ultima, Revel Ultimate, or Revel II Audio. To correct the condition, program the digital signal processing (DSP) module to the latest calibration using IDS version 102.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest calibration. Use causal part 18B849 and applicable labor operations in section 10 of the SLTS manual.
SSM 46105
Service Bulletin/Repair Instructions
Some 2015-2016 MKC, 2016 MKX, and 2016-2017 MKZ vehicles equipped with a Telematics Control Unit (TCU) built on or before 9-Aug-2016 may exhibit loss of functionality of remote features via the MyLincoln Mobile Application. To correct the condition, program the TCU to the latest calibration using IDS version 102.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest calibration. Calibration files may also be obtained at www.motorcraftservice.com. For 2015 MKC/MKZ vehicles make sure FSA 15N04 has been completed prior to attempting reprogramming. If FSA 15N04 has been completed and the TCU is at the latest calibration, then refer to WSM, Section 415-00 for normal diagnostics. Use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
SSM 46085
Service Bulletin/Repair Instructions
The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
SSM 46073
Service Bulletin/Repair Instructions
Some 2016-2017 Escape, MKC, Fiesta, F150, Expedition, Navigator, Mustang, Transit, Focus, C-Max, MKX, Taurus, MKS, Flex, MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
SSM 46069
Service Bulletin/Repair Instructions
Some 2015-2016 vehicles equipped with 6F50/6F55 transmission Built On 11/2/2015 And Through 2/1/2016 may exhibit no reverse, 3rd and 5th gear and/or DTCs P0715, P0717, P0756 and/or P2701. This may be caused by the direct clutch snap ring out of position and/or damage to the direct clutch hub. The cause of the failure is the Tone Wheel surface putting uneven load on the snap ring. To repair this condition the Tone Wheel (7F283) must be replaced,(also referred to as Direct Clutch Cylinder/Tone wheel) in addition to the Tone Wheel, replace Direct Clutch Hub (7G384), Direct Clutch Return Spring (7F235), Direct Clutch Snap Ring (7C122), TSS Sensor (7M101), Seal Kit (7153) and filter in the kit. Disassemble, clean the transmission and main control to remove metal particles. Refer to WSM, Section 307-01. Use causal part 7F283 and applicable Labor ops from SLTS section 7.
16B32
Service Bulletin/Repair Instructions
Certain 2015 Model Year Edge, 2015-2016 Model Year F-150, MKT, and Police Interceptor Sedan, and 2016 Model Year Escape, Explorer, Flex, Fusion, MKX, Mustang, Police Interceptor Utility, Taurus, and Transit Vehicles - Electronic Throttle Body Repair
SSM 46048
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may have DTCs U3000:04, B108E:12 and/or U1A00:87 present in the APIM. If these DTCs are present and no other symptoms are reported by the customer, then clear the DTCs and retest. If the DTC(s) do not return then no further repairs should be attempted. If one or more DTCs return as current faults and/or the customer reports other symptoms, then refer to Workshop Manual, Section 415-00 for further diagnostics. The SYNC version can be confirmed via OASIS.
SSM 46022
Service Bulletin/Repair Instructions
WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.
SSM 45983
Service Bulletin/Repair Instructions
SOME 2016 MKX VEHICLES BUILT ON OR BEFORE 8/5/2016 MAY DISPLAY A CHECK HEADLAMP MESSAGE IN THE INSTRUMENT CLUSTER MESSAGE CENTER WITH DIAGNOSTIC TROUBLE CODE (DTC) B1087 AND/OR B1088 PRESENT IN THE HEADLAMP CONTROL MODULE (HCM). TO CORRECT THE CONDITION, UPDATE THE HCM TO THE LATEST LEVEL CALIBRATION USING IDS VERSION 101.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR CLAIMING, USE CAUSAL PART 13K198 AND APPLICABLE LABOR OPERATION(S) IN THE SLTS MANUAL SECTION 10.
SSM 45968
Service Bulletin/Repair Instructions
SOME 2016 ESCAPE/MKC/FIESTA/F150/EXPEDITION/NAVIGATOR/MUSTANG /TRANSIT/FOCUS/C-MAX/MKX/TAURUS/MKS/FLEX/MKT/EDGE AND 2017 ESCAPE/EXPLORER/MKC/FUSION AND MKZ VEHICLES EQUIPPED WITH SYNC 3 MIGHT EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. ENGINEERING IS AWARE OF THIS POSSIBILITY AND IT IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORTATION MODE. IT IS BENEFICIAL TO EXTENDED BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. IF THE VEHICLE SHOULD EXHIBIT A BLANK SCREEN OR OTHER SYNC SYMPTOMS AFTER IT HAS BEEN TAKEN OUT OF TRANSPORT MODE, REFER TO WORKSHOP MANUAL, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
SSM 45949
Service Bulletin/Repair Instructions
SOME 2016 MKX VEHICLES MAY DISPLAY A CHECK HEADLAMP MESSAGE IN THE INSTRUMENT CLUSTER MESSAGE CENTER WITH DIAGNOSTIC TROUBLE CODE (DTC) B1087 AND/OR B1088 PRESENT IN THE HEADLAMP CONTROL MODULE (HCM). TO CORRECT THE CONDITION, UPDATE THE HCM TO THE LATEST LEVEL CALIBRATION USING IDS VERSION 101.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR CLAIMING, USE CAUSAL PART 13K198 AND APPLICABLE LABOR OPERATION(S) IN THE SLTS MANUAL SECTION 10.
SSM 45936
Service Bulletin/Repair Instructions
SOME 2015-2016 EDGE AND 2016 MKX VEHICLES BUILT ON OR BEFORE 6/11/2016 MAY EXHIBIT A NOISE FROM THE ELECTRIC COOLING FANS, MOST NOTICEABLE RIGHT AFTER THE ENGINE IS TURNED OFF AS THEY SPIN DOWN TO A STOP. IF THE NOISE CAN BE PINPOINTED TO THE COOLING FAN MOTOR, INSTALL A NEW COOLING FAN MOTOR AND SHROUD F2GZ-8C607-E WHICH WAS RELEASED FOR SERVICE TO RESOLVE THIS CONCERN.
SSM 45925
Service Bulletin/Repair Instructions
SOME 2016 MKX VEHICLES MAY DISPLAY A CHECK HEADLAMP MESSAGE IN THE INSTRUMENT CLUSTER MESSAGE CENTER WITH DIAGNOSTIC TROUBLE CODES (DTCS) B1087 AND/OR B1088 PRESENT IN THE HEADLAMP CONTROL MODULE (HCM). THIS CONCERN IS CURRENTLY UNDER INVESTIGATION. CONTINUE TO MONITOR OASIS FOR UPDATES.
SSM 45926
Service Bulletin/Repair Instructions
2013-2017 FUSION/ESCAPE/MKZ (EXCLUDING 3.7L), 2015-2016 EDGE/EXPLORER (EXCLUDING 3.5L/3.7L), 2015-2016 MKC, AND 2016 MKX VEHICLES (EXCLUDING 3.7L) EQUIPPED WITH ALL WHEEL DRIVE (AWD) MAY EXHIBIT A LEAKING PASSENGER SIDE POWER TRANSFER UNIT (PTU) HALFSHAFT/LINKSHAFT SEAL. THIS MAY BE DUE TO A WORN PTU BUSHING. THE PTU BUSHING CAN NOW BE REPAIRED WITHOUT PTU REPLACEMENT. THE ONLINE WSM IS BEING UPDATED FOR ALL LISTED VEHICLES.REFER TO THE INTERMEDIATE SHAFT BUSHING REMOVAL AND INSTALLATION IN WORKSHOP MANUAL (WSM), SECTION 308-07. THE PROCEDURE IS THE SAME FOR ALL VEHICLES. IF THE PROCEDURE IS NOT PUBLISHED FOR THE VEHICLE BEING SERVICED CHECK THE WSM OF ANOTHER LISTED VEHICLE. BUSHING PART NUMBER IS F2GZ-63600A58A. THE PARTS CATALOG IS BEING UPDATED TO INCLUDE THIS BUSHING.
TSB16-0094
Service Bulletin/Repair Instructions
SOME 2015-2016 EDGE AND 2016 MKX VEHICLES EQUIPPED WITH A 2.7L ECOBOOST ENGINE AND BUILT ON 10/29/2015 AND THROUGH 4/1/2016 MAY EXHIBIT A KNOCKING/TAPPING NOISE THAT CAN BE HEARD IN THE FUEL FEED TUBE THAT ATTACHES TO THE HIGH PRESSURE FUEL PUMP ON THE ENGINE. THIS MAY BE DUE TO A LOOSE CHECK VALVE LOCATED IN THE FUEL FEED TUBE. FOLLOW THE TSB SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 45916
Service Bulletin/Repair Instructions
SOME 2016 FORD AND LINCOLN VEHICLES EQUIPPED WITH SYNC 3 AND NAVIGATION ALONG WITH A VALID PAID SUBSCRIPTION TO SIRIUS TRAVEL LINK MAY NOT DISPLAY SIRIUS TRAVEL LINK FUEL PRICES. REPLACING COMPONENTS WILL NOT RESOLVE THE CONDITION AND IS NOT RECOMMENDED AT THIS TIME. ENGINEERING IS CURRENTLY INVESTIGATING. IN THE INTERIM, THE FOLLOWING STEPS WILL RESET THE SYSTEM. POSITION THE VEHICLE OUTDOORS IN OPEN SKY. DISCONNECT THE BATTERY FOR 5 MINUTES. RECONNECT THE BATTERY AND START THE VEHICLE. SELECT SIRIUS TRAVEL LINK THEN FUEL PRICES. FUEL PRICE INFORMATION MAY NOT DISPLAY FOR UP TO 15 MINUTES WHILE THE SYSTEM IS UPDATING. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.
SSM 45917
Service Bulletin/Repair Instructions
SOME 2016-2017 VEHICLES EQUIPPED WITH SYNC 3 MAY EXPERIENCE THE FOLLOWING CONCERNS; THE GPS NOT TRACKING THE VEHICLE POSITION CORRECTLY, THE VEHICLE LOCATION ARROW ICON SPINNING IN CIRCLES ON THE NAVIGATION SCREEN OR A SPINNING COMPASS ON NON-NAVIGATION VEHICLES. PERFORM THE FOLLOWING PROCEDURE TO RESOLVE. ENTER BEZEL DIAGNOSTICS PER WORK SHOP MANUAL (WSM) SECTION 415-00. SELECT TESTING SETTINGS FROM THE MENU. SCROLL DOWN AND PRESS CLEAR DR CALIB. PERFORM A DRIVE TEST FOR APPROXIMATELY 10 MINUTES, INCLUDE AT LEAST FOUR RIGHT TURNS AND FOUR LEFT TURNS WITH A VEHICLE SPEED OF AT LEAST 25 MPH. CONFIRM THAT GPS POSITION FOR NAVIGATION OR THE COMPASS FOR NON-NAVIGATION VEHICLES IS FUNCTIONING PROPERLY. ENGINEERING IS AWARE OF THIS CONCERN. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.
SSM 45918
Service Bulletin/Repair Instructions
SOME 2016-2017 FORD/LINCOLN VEHICLES WITH SYNC 3 MAY SEE A NAVIGATION FAULT MESSAGE APPEAR ON THE MAP ON THE HOME SCREEN OR A SYSTEM LOCK UP WHEN THE PHONE IS CONNECTED. APPLINK MAYBE INOPERATIVE, OR THE SYSTEM MAY PERFORM RANDOM REBOOTS DURING AN IGNITION CYCLE WITH THE PHONE CONNECTED. DETERMINE IF THE CUSTOMER HAS AN ANDROID PHONE WITH THE BASEBALL APPLICATION MLB.COM AT BAT INSTALLED. IF THE CUSTOMER DOES NOT HAVE THIS APPLICATION LOADED THEN PROCEED TO THE WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. IF THE CUSTOMER DOES HAVE THIS APPLICATION LOADED VERIFY IF THE VERSION IS 5.1.3 OR LOWER ON THE ANDROID PHONE. IF THE ANDROID PHONE WITH MLB.COM AT BAT HAS VERSION 5.1.3 OR LOWER PLEASE RECOMMEND THAT THEY UPDATE THEIR APP TO VERSION 5.2 OR HIGHER AND RETEST FOR THE CUSTOMER SYMPTOM. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
TSB-16-0090
Service Bulletin/Repair Instructions
SOME 2016 EXPLORER AND MKX VEHICLES BUILT ON OR BEFORE 3/11/2016 MAY EXHIBIT A MEMORY SEAT THAT DOES NOT RETURN TO THE PROGRAMMED POSITION WHEN PRESSING THE MEMORY SEAT SWITCH OR PROGRAMMED INTELLIGENT ACCESS (IA) KEY; AND/OR EASY ENTRY/EXIT FUNCTION THAT DOES NOT RETURN TO THE PREVIOUS SEAT POSITION.
SSM-45857
Service Bulletin/Repair Instructions
2015-2016 EDGE AND 2016 LINCOLN MKX - OVERLY SENSITIVE BRAKE APPLICATION AT LOWSPEED AND/OR IN COLD/WET CONDITIONS - BUILT ON OR BEFORE 3/23/2016
TSB-16-0088
Service Bulletin/Repair Instructions
SOME 2016 LINCOLN MKX VEHICLES BUILT ON OR BEFORE 3/21/2016 MAY EXHIBIT WIND NOISE AT THE DRIVER AND/OR PASSENGER A-PILLAR TO WINDSHIELD AREA. THE NOISE IS MOST NOTICEABLE AT HIGHWAY SPEEDS. THIS MAY BE DUE TO THE WINDSHIELD A- MOULDING NOT BEING PROPERLY ADHERED TO THE A-PILLAR SHEET METAL AND/OR FROM THE SHAPE OF THE CHANNEL THAT RUNS INSIDE THE WINDSHIELD MOULDING.
SSM-45821
Service Bulletin/Repair Instructions
SIRI EYES FREE FUNCTIONAL ISSUES USING BLUETOOTH AND APPLE IOS 9.2 AND 9.2.1
SSM-45809
Service Bulletin/Repair Instructions
SYNC 3 ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DTCS U3000 OR B108E OR U1A00
TSB-16-0078
Service Bulletin/Repair Instructions
SOME 2016 MKX VEHICLES EQUIPPED WITH A 3.7L DURATEC ENGINE AND BUILT ON OR BEFORE 4/21/2016 MAY EXHIBIT AN ILLUMINATED MIL WITH DTC P013C STORED IN THE POWERTRAIN CONTROL MODULE (PCM). THIS MAY BE CAUSED BY IMPROPER SEALING OF THE LEFT SIDE EXHAUST Y-PIPE FLANGE DUE TO WELD SPLATTER OR EXHAUST PIPE INTRUSION INTO THE FLANGE SEALING SURFACE.
16-0077
Service Bulletin/Repair Instructions
Some 2016 MKX vehicles equipped with climate controlled seats and built on or before 3/31/2016 may exhibit a lack of cooling/heating from the front seat bottom cushion due to a lack of air flow through the climate controlled seat bottom cushion duct
16-0066
Service Bulletin/Repair Instructions
Some 2012-2016 vehicles equipped with a touchscreen navigation system and the language set to Arabic may exhibit a blank screen. This may be the result of the ribbon cables not being fully seated inside the front display interface module (FDIM) or an improper software configuration of the FDIM.
TSB160066
Service Bulletin/Repair Instructions
Touchscreen navigation system - arabic language - blank screen
16-0063
Service Bulletin/Repair Instructions
Some 2016 MKX vehicles equipped with climate controlled seats and built on or before 2/13/2016 may exhibit a lack of cooling performance from the front seat backrests.
16-0058
Service Bulletin/Repair Instructions
Some 2015-2016 MKC and 2016 MKX vehicles may exhibit a wind or whistle noise from the exterior mirror(s) at highway speed.
TSB160077
Service Bulletin/Repair Instructions
Claimate controlled seats - lack of cooling /heating from front seat bottom cushion - built on or before 03/31/2016
16-0045
Service Bulletin/Repair Instructions
2.0L ECOBOOST - FUEL ODOR ISSUE Some 2013-2016 Escape, 2015-2016 MKC vehicles built on or before 12/15/2015, 2013-2016 Fusion, MKZ, 2013-2015 Explorer, 2013-2014 Focus ST and Edge vehicles equipped with 2.0L EcoBoost engines may exhibit fuel odor originating from the positive crankcase ventilation (PCV) hose. SERVICE PROCEDURE 1. Is the vehicle a 2016 Escape or MKC? a. Yes - check the vehicle build date. Was the vehicle built on or before 12/15/2015? (1) Yes - proceed to Step 2. (2) No - this article does not apply. b. No - proceed to Step 2. 2. Inspect the PCV hose to make sure it is properly connected to the valve cover and the low pressure intake duct. a. For Escape and Focus ST vehicles remove the cowl panel grille to access the hose. Refer to Workshop Manual (WSM), Section 501-02. b. For Edge vehicles remove the air cleaner outlet pipe to access the hose. Refer to WSM, Section 303-12. 3. Does the PCV hose exhibit a fuel smell or was the hose disconnected? a. Yes - replace hose and reassemble the vehicle. b. No - Refer to WSM, Section 303-13 for normal diagnosis.
TSB160063
Service Bulletin/Repair Instructions
Claimate controlled seats - lack of cooling performance from the front seat backrest - Built on or before 02/13/2016
CSC15B25
Service Bulletin/Repair Instructions
Customer Satisffaction Program 15b25 Certain 2016 Model Year Lincoln MKX Vehicles Replace A-Pillar Trim Panels
SB-45317
Service Bulletin/Repair Instructions
2016 MKZ,MKC AND MKX: MY LINCOLN MOBILE APP NOT ABLE TO CONNECT TO VEHICLES EQUIPPED WITH DTC U2100 AND/OR U2101 ON VEHICLES WITH TELEMATICS CONTROL UNIT *CN
ASI-45223
Service Bulletin/Repair Instructions
LINCOLN: ON SOME VEHICLES, WHERE A PILLAR TRIM PANEL AND HEADLINER MEETS, A PILLAR TRIM PANEL FAILS TO STAY SEATED UNDER WEATHER STRIP FRONT DOOR AND TO PROVIDE TEMPORARY RESOLUTION, A PILLAR TRIM PANEL IS RESEATED. MODEL 2016 MKX. *PE
ASI-45231
Service Bulletin/Repair Instructions
LINCOLN: INFORMATION REGARDING THE REPORTING OF ANY PRODUCT ISSUES, IN DETAIL, THROUGH GLOBAL CONCERN REPORTING (GCR) AND SELECTION OF AN ALTERNATE METHOD AND EMAIL. MODEL 2016 MKX. *PE
ASI-45242
Service Bulletin/Repair Instructions
LINCOLN: SOME VEHICLES THERE IS NO OBSERVABLE CUSTOMER SYMPTOMS WITH DIAGNOSTIC TROUBLE CODE (DTC) U0198, STORED IN ACCESSORY PROTOCOL INTERFACE MODULE (APIM), AND CAUSES NO MALFUNCTION INDICATOR LAMPS (MIL) TO ILLUMINATE. MODEL 2016 MKX. *PE
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.