25N17
Other
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Vehicle report
2016 LINCOLN MKZ
Service bulletins
135 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 54366
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
20R01 S1
Service Bulletin/Repair Instructions
Certain 2014-2015 Model Year Fiesta, 2014-2016 Model Year Fusion, MKZ and 2014-2016 Model Year Transit Connect Vehicles Not Covered in Safety Recall: 20S15 or 23S36 Door Latch Replacement and Inspection
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
21B09 S2
Service Bulletin/Repair Instructions
Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit REASON FOR THIS SUPPLEMENT Program Terms & Urgency / Expiration Date: Program extension until July 31, 2023. Service Action: o IDS level 128 or higher is now required to address various programming issues encountered. o C-MAX Energi vehicles are now serviceable with new software and hardware. Labor Allowances: C-MAX labor has been updated. Parts Requirements / Ordering Information: o The C-MAX 4G Upgrade Kit is now orderable at this time with a new part number. o MKX Rear seat backrest nut claim quantity updated. Technical Information updates: o Ensure IDS level 128 or higher is used. o Toggling Valet Mode is no longer required. o C-MAX Energi instructions are now available. Owner Notification: Non-repaired vehicle owners will be mailed the week of April 17, 2023. Pickup and Delivery: Added Customer Acknowledgement Form - Review form contents with customer prior to kit ordering and obtain customer signature prior to installation for Focus BEV, C-MAX, and Fusion Energi vehicles.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 51261
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 51181
Service Bulletin/Repair Instructions
Some 2013-2016 Escape/Fusion/MKZ vehicles may display an error message when updating the All Wheel Drive-ATC Barcode using the IDS service function after installing a new rear drive unit assembly (RDU) or active torque coupling (ATC) clutch assembly. To prevent this error from occurring, enter the universal ATC 4 digit barcode 7772. Once programmed, perform several figure 8 turns at parking lot speeds to verify there is no binding from the all wheel drive (AWD) system. If the vehicle binds in a turn, perform Pinpoint Test A. Refer to the Workshop Manual (WSM), Section 308-07A > Diagnosis and Testing.
TSB 22-2396
Service Bulletin/Repair Instructions
Some 2013-2020 Fusion, MKZ and 2013-2018 C-Max vehicles equipped with an HF35 transmission may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.
TSB 22-2381
Service Bulletin/Repair Instructions
Some 2015-2018 Fusion/MKZ vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise from the transmission bellhousing area. This may be more noticeable at idle. This may be due to a flexplate crack around the mounting area. To correct the condition, follow the Service Procedure to replace the flexplate, transmission fluid pump, and torque converter.
SSM 51120
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
22N02 S1
Service Bulletin/Repair Instructions
Certain 2015-2019 Model Year Edge and Lincoln MKX Vehicles and 2013-2018 Model Year Fusion and Lincoln MKZ Vehicles Front Brake Flexible Hose Replacement REASON FOR THIS SUPPLEMENT Parts Requirements / Ordering Information: Part numbers for Edge and MKX vehicles have been added. Edge and MKX model year updated from 2018 to 2019, build dates remain the same.
22N02
Service Bulletin/Repair Instructions
Certain 2015-2018 Model Year Edge and Lincoln MKX Vehicles and 2013-2018 Model Year Fusion and Lincoln MKZ Vehicles Front Brake Flexible Hose Replacement Submitting Owner Letters
TSB 22-2309
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
21B09-S1
Service Bulletin/Repair Instructions
Certain 2014-2020 Model Year Multiple Vehicle Lines - 3G Telematics Control Unit to 4G Upgrade Kit. The North America 3G cellular service began decommissioning in August 2021 and a complete shutdown of the 3G network took place in February 2022. Vehicles on the road equipped with a 3G telematics control unit (TCU) / embedded modem will lose mobile app functionality/connectivity.
TSB 22-2230
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
SSM 50861
Service Bulletin/Repair Instructions
Some 2015-2016 vehicles equipped with 6F50/6F55 transmission and built on 2-Nov-2015 and through 1-Feb-2016 may exhibit no reverse, 3rd and 5th gear with diagnostic trouble codes (DTCs) P0715,P0717,P0756 and/or P2701. This may be caused by the direct clutch cylinder/tone wheel (7F283) inadvertently forcing the snap ring out of position resulting in damage to the direct clutch hub (7G384). Service part (7J250) complete rotating 3-5-R clutch module is now available. Refer to Workshop Manual (WSM), Section 307-01. For claiming, use causal part 7F283 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) manual.
SSM 50804
Service Bulletin/Repair Instructions
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
SSM 50744
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
TSB 22-2162
Service Bulletin/Repair Instructions
Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
TSB 22-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 50257
Service Bulletin/Repair Instructions
Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
21B09
Service Bulletin/Repair Instructions
Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit The North America 3G cellular service began decommissioning in August 2021 and will be fully decommissioned in February 2022. Vehicles on the road equipped with a 3G telematics control unit (TCU) / embedded modem will lose mobile app functionality/connectivity. Some owners are still within the *complimentary trial period (depending on model year and brand, see table below) for connected services.
TSB 21-2347
Service Bulletin/Repair Instructions
Some 2015-2020 Fusion/MKZ vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise from the transmission bellhousing area. This may be more noticeable at idle. This may be due to a flexplate crack around the mounting area. To correct the condition, follow the Service Procedure steps to replace the flexplate, transmission fluid pump, and torque converter.
SSM 50067
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50064
Service Bulletin/Repair Instructions
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
TSB 21-2236
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 49821
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2004
Service Bulletin/Repair Instructions
Some 2013-2020 MKZ vehicles may need the exterior rear view mirror replaced. The replacement exterior mirror will have different wiring than the originally equipped mirror. Follow the Service Procedure steps below to modify the vehicle-side wiring harness to accept the replacement mirror wiring.
TSB 20-2386
Service Bulletin/Repair Instructions
Some 2013-2020 MKZ vehicles may need the exterior rear view mirror replaced. The replacement exterior mirror will have different wiring than the originally equipped mirror. Follow the Service Procedure steps below to modify the vehicle-side wiring harness to accept the replacement mirror wiring.
TSB 20-2372
Service Bulletin/Repair Instructions
This article supersedes 17-2225 to update the vehicle model years affected and Service Procedure. Some 2013-2014 Fusion and 2013-2020 MKZ vehicles may exhibit unintended exterior mirror movement in wet weather conditions. This may be due to water intrusion into the exterior mirror connector. To correct the condition, follow the Service Procedure steps to remove the 16 pin connector and install two weather tight 8 pin connectors.
SSM 49210
Service Bulletin/Repair Instructions
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2233
Service Bulletin/Repair Instructions
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
TSB 20-2219
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion/MKZ/C-MAX vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.
SSM 48908
Service Bulletin/Repair Instructions
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
SSM 48858
Service Bulletin/Repair Instructions
Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
TSB 20-2171
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 48619
Service Bulletin/Repair Instructions
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
SSM 48578
Service Bulletin/Repair Instructions
Some 2013-2016 MKZ vehicles equipped with adaptive headlamps may exhibit a Check Headlamp System fault message in the instrument panel cluster (IPC) after the right headlamp is replaced. Diagnostic trouble code (DTC) B1D65 may also be stored in the headlamp control module (HCM). To correct this condition install a new right headlamp (13008). Right headlamps built on or after 17-Oct-2019, or reworked headlamp assemblies identified with a green dot on the box and/or a green paint mark on the headlamp near the part number label, will no longer have this issue. For claiming, use Causal Part (13008) and applicable Labor Times in the Service Labor Time Standards (SLTS) Manual.
TSB 19-2391
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, MKZ and C-MAX vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.
SSM 48423
Service Bulletin/Repair Instructions
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-2390
Service Bulletin/Repair Instructions
Some 2015-2019 F-150, 2015-2020 Explorer, 2017-2019 F-Super Duty, 2017-2020 Continental, 2018-2020 Expedition/Navigator, 2016-2018 MKX, 2019-2020 Nautilus, 2020 Aviator/Corsair and 2013-2020 MKZ vehicles equipped with multi-contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.
SSM 48406
Service Bulletin/Repair Instructions
Some 2013-2016 MKZ vehicles equipped with adaptive headlamps may exhibit a Check Headlamp System fault message in the instrument panel cluster (IPC) after installation of a new right headlamp. Diagnostic trouble code (DTC) B1D65 may also be stored in the headlamp control module (HCM). This may be due to a quality issue with the right headlamp service part, which was corrected on headlamps built on and after 17-Oct-2019. In addition, some headlamps with Earlier build dates were reworked with corrective actions and may be installed. Reworked headlamp assemblies are identified by having a green dot on the box and/or a green paint mark on the headlamp near the part number label. For claiming, use the headlamp base number as the causal part and applicable labor from the Service Labor Time Standards (SLTS) Manual.
SSM 48263
Service Bulletin/Repair Instructions
Some 2013-2016 MKZs vehicles with Adaptive Headlamps may exhibit a Check Headlamp System fault message in the instrument panel cluster (IPC) after one or both headlamps were replaced. Diagnostic trouble codes (DTCs) B1D64 and/or B1D65 may also be stored in the headlamp control module (HCM). Confirm the headlamps illuminate normally, but do not attempt additional repairs at this time. Engineering is investigating, monitor OASIS for updates. The swivel function will remain inoperative until a corrective action becomes available. The headlamps will continue to function to fully meet all applicable lighting requirements.
TSB 19-2293
Service Bulletin/Repair Instructions
Some 2015-2019 F-150/Explorer, 2017-2019 F-Super Duty/Continental, 2018-2019 Expedition/Navigator, 2016-2018 MKX, 2019 Nautilus, and 2013-2019 MKZ vehicles equipped with Multi-Contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.
SSM 48130
Service Bulletin/Repair Instructions
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
SSM 48123
Service Bulletin/Repair Instructions
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
SSM 48108
Service Bulletin/Repair Instructions
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 48067
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion and MKZ vehicles may not have a valid 5 digit key code stored in the Ford key code retrieval system. If both keys are lost and the original selling dealer does not have the key code on file, a new lock set may be needed. For Fusion IKT (non push-button start) use lock set ES7Z-5422050-A, Fusion push-button start use lock set ES7Z-5422050-B, and for Lincoln MKZ use lock set DP5Z-5422050-A. Kits include pre-cut keys. The push-button start kits come with back-up key blades, but do not include passive key remotes which will need to be ordered separately. Rotunda, the Technical Assistance Center, or the Customer Relations Center will not have key code information.
TSB 19-2172
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
SSM 47993
Service Bulletin/Repair Instructions
2015-2016 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Taurus Police/Explorer/Explorer Police vehicles built on or before 10-Jun-2016 and equipped with a 3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) may exhibit a PTU venting, an odor originating from the PTU, or noise originating from the PTU. These vehicles may be a candidate for rebuild using PTU Idler Gear/Shaft/Bearing Kit (GB5Z-7P258-A). Refer to Workshop Manual (WSM), Section 308-07.
SSM 47976
Service Bulletin/Repair Instructions
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 47850
Service Bulletin/Repair Instructions
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 47948
Service Bulletin/Repair Instructions
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 47824
Service Bulletin/Repair Instructions
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
TSB 19-2026
Service Bulletin/Repair Instructions
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
SSM 47790
Service Bulletin/Repair Instructions
Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
TSB 19-2017
Service Bulletin/Repair Instructions
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
SSM 47749
Service Bulletin/Repair Instructions
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
SSM 47711
Service Bulletin/Repair Instructions
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
TSB 18-2361
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 47662
Service Bulletin/Repair Instructions
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 47649
Service Bulletin/Repair Instructions
2013 2018 C-Max, Fusion, and MKZ Hybrid vehicles using SOBDM-C module connectors do not require electrical/dielectric grease. If used it may induce module communication concerns. Codes present may be U0293 and a P0AA6. The Workshop Shop Manual (WSM) does not state to use it on these module connectors.
SSM 47635
Service Bulletin/Repair Instructions
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 47638
Service Bulletin/Repair Instructions
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
TSB 18-2328
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, MKZ and C-Max vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. Follow the Service Procedure steps to correct the condition.
SSM 47538
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
SSM 47489
Service Bulletin/Repair Instructions
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
TSB 18-2255
Service Bulletin/Repair Instructions
Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
SSM 47462
Service Bulletin/Repair Instructions
2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures
SSM 47444
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47379
Service Bulletin/Repair Instructions
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47380
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47230
Service Bulletin/Repair Instructions
Some 2007-2016 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Police Interceptor Sedan/Explorer/Police Interceptor Utility vehicles equipped with AWD and built on or before 30-Jun-2016 may exhibit a propane or natural gas odor during idle or low speed driving. This may be due to break down of the power transfer unit (PTU) fluid caused by excessive heat. If the source of the odor is identified as originating from the PTU, an idler bearing repair kit is available to repair the PTU. Refer to the Workshop Manual (WSM), Section 308-07. If the PTU is determined to be repairable, utilize kit GB5Z-7P258-A and the included instruction sheet. For claiming use causal part 7P258 and applicable labor operations in section 07 of the Service Labor Time Standards (SLTS) Manual.
SSM 47211
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47201
Service Bulletin/Repair Instructions
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
SSM 47204
Service Bulletin/Repair Instructions
Some 2015-2018 Fusion/MKZ/MKC/Escape/Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a runs rough condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.
SSM 47167
Service Bulletin/Repair Instructions
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47159
Service Bulletin/Repair Instructions
Some 2016 MKC, MKX and MKZ vehicles built on or before 11/28/2015 and equipped with a TCU may exhibit an intermittent battery draw that can be isolated to the TCU, an inoperative MyLincoln Mobile app, a MyLincoln Mobile app deep sleep message, an inaccurate MyLincoln Mobile app oil life message, an incorrect MyLincoln Mobile app fuel level, a MyLincoln Mobile app false low tire warning and/or Diagnostic Trouble Codes U2100 and/or U2101 stored in the TCU. To correct the condition, program the TCU to the latest calibration using IDS version 108.06 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest calibration. For warranty claiming, use causal part 14G229 and applicable labor operations in the SLTS Manual, Section 10.
SSM 47160
Service Bulletin/Repair Instructions
Some 2015-2017 MKC/MKZ, 2016-2017 MKX and 2017 Continental vehicles equipped with a Telematics Control Unit (TCU) built on or before 15-Aug-2017 may exhibit inoperative remote features via Lincoln Way Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU Field Service Actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.06 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
SSM 47129
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Fusion Energi, 2013-2018 C-MAX/Fusion Hybrid/MKZ Hybrid may exhibit a no start with battery energy control module (BECM) diagnostic trouble code (DTC) P0AE5. For 2015-2017 C-MAX Energi refer to the 2014 MY C-MAX Workshop Manual (WSM), Section 414-03A for normal diagnostics. For all vehicles, if WSM pinpoint testing for BECM DTC P0AE5 finds the DC/DC converter control module (14B227), cabin coolant heater (18K463) or A/C compressor (19703) has low high voltage circuit internal resistance, only replace the component found with low internal resistance. It is not necessary to replace the high voltage battery junction (10C666) along with the low resistance high voltage component. The WSM is currently under revision.
SSM 47080
Service Bulletin/Repair Instructions
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
SSM 47070
Service Bulletin/Repair Instructions
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 47041
Service Bulletin/Repair Instructions
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47000
Service Bulletin/Repair Instructions
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 46948
Service Bulletin/Repair Instructions
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
SSM 46949
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
17-2225
Service Bulletin/Repair Instructions
Some 2013-2014 Fusion and 2013-2018 MKZ vehicles may exhibit unintended exterior mirror movement in wet weather conditions due to moisture in the exterior mirror connector. Follow the Service Procedure steps to correct the condition.
SSM 46900
Service Bulletin/Repair Instructions
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 46848
Service Bulletin/Repair Instructions
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
SSM 46834
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
17B28
Service Bulletin/Repair Instructions
Certain 2015 Model Year Flex and Taurus, 2015-2016 Model Year C-MAX, and MKS, and 2016 Model Year Edge, Fusion, MKZ, and Transit Connect Vehicles - Electronic Throttle Body Replacement
SSM 46813
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.
SSM 46703
Service Bulletin/Repair Instructions
Some 2013-2017 Edge/MKX/Escape/MKC/Fusion/MKZ/Flex/MKT/Mondeo/Kuga/EcoSport AWD vehicles where diagnosis leads to a RDU clutch issue, a rear drive unit (RDU) service kit is available. Use the vehicle identification number (VIN) in the parts catalog to look for base part 4A232. If clutch assembly (base 4A232) is not listed in the catalog, this message does not apply. For vehicle repairs refer to updated Workshop Manual (WSM), Section 205-02 on ATC clutch repairs. Use causal part 4A232 or equivalent and applicable labor operations.
TSB 17-2057
Service Bulletin/Repair Instructions
Some 2013-2014 Fusion and 2013-2017 MKZ vehicles may exhibit unintended exterior mirror movement in wet weather conditions due to moisture in the exterior mirror connector. Follow the Service Procedure steps to correct the condition.
TSB 17-0039
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, MKZ and 2013-2016 C-Max vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving, but will not be present when the vehicle is stationary or in Park. Follow the Service Procedure steps to correct the condition.
SSM 46522
Service Bulletin/Repair Instructions
2013-2017 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Taurus Police/Explorer/Explorer Police/Continental vehicles equipped with a 3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) that is being repaired or replaced for an internal failure must also have the vent hose replaced due to contamination in the hose.
SSM 46438
Service Bulletin/Repair Instructions
SOME 2016-2017 F150, EDGE, MKX, ESCAPE, FOCUS, MKC, FUSION, MKZ, TAURUS AND 2017 CONTINENTAL VEHICLES EQUIPPED WITH 2.0L, 2.7L OR 3.0L GASOLINE TURBOCHARGED DIRECT INJECTION(GTDI) ECOBOOST ENGINES MAY EXHIBIT MALFUNCTION INDICATOR LIGHT(MIL) ON WITH DIAGNOSTIC TROUBLE CODES(DTC) P1013, P1015 AND/OR P1016 STORED IN POWERTRAIN CONTROL MODULE(PCM). CHECK TURBOCHARGER WASTEGATE CONTROL HOSES FOR WATER/ICE RESTRICTIONS OR PINCHING AT ZIP-TIE ON ENGINE CAM COVER RETAINER(2.7L AND 3.0L ONLY). IF RESTRICTION IS FOUND ON CAM COVER RETAINER, CUT ZIP TIE AND CLEAR DTCS. IF WATER/ICE RESTRICTION IS FOUND, DRAIN HOSES, REASSEMBLE AND CLEAR DTCS. IF DTCS RETURN, REFER TO WORKSHOP MANUAL (WSM) OR POWERTRAIN CONTROL EMISSIONS DIAGNOSIS (PCED) MANUAL FOR NORMAL DIAGNOSTICS. ENGINEERING IS INVESTIGATING THE CONCERN, MONITOR OASIS FOR FURTHER UPDATES.
SSM 46412
Service Bulletin/Repair Instructions
SOME 2007-2016 EDGE/MKX/FLEX/MKT/MKZ/MKS/TAURUS/TAURUS POLICE/EXPLORER/EXPLORER POLICE EQUIPPED WITH ALL WHEEL DRIVE (AWD) AND BUILT ON OR BEFORE 30-JUN-2016 MAY EXHIBIT A TICKING AND/OR KNOCKING NOISE COMING FROM THE DRIVELINE AREA. TO IDENTIFY THIS NOISE, REFER TO WORKSHOP MANUAL (WSM), SECTION 100-04, AND FOLLOW THE SYMPTOM CHART. IF THE SOURCE OF THE NOISE IS IDENTIFIED AS THE PTU AND/OR INTERNAL TO THE PTU, DISASSEMBLE PTU ASSEMBLY. REFER TO UPDATED WSM, SECTION 308-07. IF THE PTU IS DETERMINED TO BE REPAIRABLE, UTILIZE KIT GB5Z-7P258-A AND THE INCLUDED INSTRUCTION SHEET. FOR CLAIMING, USE CAUSAL PART 7P258 AND APPLICABLE LABOR OPERATIONS IN SECTION 07 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46371
Service Bulletin/Repair Instructions
SOME 2012-2017 FOCUS ELECTRIC/2013-2017 CMAX ENERGI/FUSION ENERGI/2015-2017 MKC/MKZ/2016-2017 MKX AND 2017 CONTINENTAL VEHICLES OPERATING WITH A 3G TCU ON OR BEFORE 16-JAN-2017 MAY NOT RESPOND TO CUSTOMERS REMOTE COMMANDS VIA MYLINCOLN/MYFORD MOBILE PHONE APPLICATIONS. 2G NETWORKS WERE DECOMMISSIONED ON 16-JAN-2017. IF THE 3G TCU WAS OPERATING ON A 2G NETWORK, IT WILL NOT AUTOMATICALLY ATTEMPT TO RECONNECT TO THE REPLACEMENT 3G NETWORK. TO CORRECT, RESET THE TCU BY REMOVING ITS POWER FUSE FOR 5 MINUTES. IF THE CONCERN IS STILL PRESENT, FOLLOW NORMAL DIAGNOSTICS IN WORKSHOP MANUAL (WSM), SECTION 415-00. REFER TO PTS OASIS HOME PAGE FOR TCU VERSION IDENTIFICATION. FOR CLAIMING, USE CAUSAL PART 14G229 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46355
Service Bulletin/Repair Instructions
MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46332
Service Bulletin/Repair Instructions
REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.
SSM 46295
Service Bulletin/Repair Instructions
TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
SSM 46281
Service Bulletin/Repair Instructions
SOME 2015-2017 EDGE/MKX, ESCAPE/MKC, FUSION/MKZ AND EXPLORER VEHICLES EQUIPPED WITH A 2.0L OR 2.3L MAY EXHIBIT DAMAGE TO THE ENGINE APPEARANCE COVER, VALVE COVER AND/OR INTAKE MANIFOLD WHEN ATTEMPTING TO REMOVE THE APPEARANCE COVER. TO REDUCE THE POSSIBILITY OF DAMAGE, CAREFULLY PULL STRAIGHT UPWARD ON THE UNDERSIDE OF THE COVER AT EACH FASTENER LOCATION TO REMOVE. DO NOT PULL THE COVER FORWARD OR TO THE SIDE. BEFORE INSTALLING THE ENGINE APPEARANCE COVER, APPLY MOTORCRAFT SILICONE BRAKE CALIPER GREASE AND DIELECTRIC COMPOUND (XG-3-A) TO THE COVER FASTENER GROMMETS. WORKSHOP MANUAL (WSM) INFORMATION IS IN THE PROCESS OF BEING UPDATED
SSM 46210
Service Bulletin/Repair Instructions
SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.
SSM 46153
Service Bulletin/Repair Instructions
SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.
SSM 46155
Service Bulletin/Repair Instructions
SOME 2015-2017 MKC, 2016 MKX, AND 2016-2017 MKZ VEHICLES EQUIPPED WITH A TELEMATICS CONTROL UNIT (TCU) BUILT ON OR BEFORE 19-OCT-2016 MAY EXHIBIT LOSS OF FUNCTIONALITY OF REMOTE FEATURES VIA THE MYLINCOLN MOBILE APPLICATION. TO CORRECT THE CONDITION, PROGRAM THE TCU TO THE LATEST CALIBRATION USING IDS VERSION 102.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST CALIBRATION. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR 2015 MKC/MKZ VEHICLES MAKE SURE FSA 15N04 HAS BEEN COMPLETED PRIOR TO ATTEMPTING REPROGRAMMING. IF FSA 15N04 HAS BEEN COMPLETED AND THE TCU IS AT THE LATEST CALIBRATION, THEN REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSTICS. USE CAUSAL PART 14G229 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL
SSM 46132
Service Bulletin/Repair Instructions
SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.
SSM 46129
Service Bulletin/Repair Instructions
SOME 2013-2016 FUSION/ESCAPE/MKT/FLEX/MKS/TAURUS, 2015-2016 MKZ/MKC/EDGE AND 2016 MKX VEHICLES MAY EXHIBIT VARIOUS RADIO CONCERNS INCLUDING: SPEAKER STATIC WITH KEY-OFF, NO AUDIO AFTER VEHICLE IS FIRST STARTED WITH DIAGNOSTIC TROUBLE CODE (DTC) U0184, NO VOLUME CONTROL, OR A STUCK CD WITH NO SLOT BLOCKAGE. PRIOR TO STARTING NORMAL DIAGNOSIS FOR ANY OF THESE CONDITIONS, VERIFY THE ACM IS AT THE LATEST CALIBRATION USING IDS VERSION 102.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE THE APPLICABLE LABOR OPERATION IN SECTION 11 OF THE SLTS MANUAL AND CAUSAL PART 18C869 WHEN CLAIMING THIS REPAIR.
SSM 46118
Service Bulletin/Repair Instructions
WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.
TSB 16-0139
Service Bulletin/Repair Instructions
SOME 2015-2016 F-150, C-MAX, EDGE, MKS, TAURUS, AND FLEX AND 2016 EXPEDITION, EXPLORER, ESCAPE, FUSION, MUSTANG, MKZ, MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46102
Service Bulletin/Repair Instructions
Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
SSM 46105
Service Bulletin/Repair Instructions
Some 2015-2016 MKC, 2016 MKX, and 2016-2017 MKZ vehicles equipped with a Telematics Control Unit (TCU) built on or before 9-Aug-2016 may exhibit loss of functionality of remote features via the MyLincoln Mobile Application. To correct the condition, program the TCU to the latest calibration using IDS version 102.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest calibration. Calibration files may also be obtained at www.motorcraftservice.com. For 2015 MKC/MKZ vehicles make sure FSA 15N04 has been completed prior to attempting reprogramming. If FSA 15N04 has been completed and the TCU is at the latest calibration, then refer to WSM, Section 415-00 for normal diagnostics. Use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
SSM 46098
Service Bulletin/Repair Instructions
2013-2017 Fusion, MKZ and C-Max Hybrid and Energi vehicles equipped with HF35 eCVT transaxles may have literature published that lists either a 2.56 or 2.57 axle ratio. For service and parts ordering purposes, both are the same. The difference in the displayed ratio originates from rounding differences between systems which results in the discrepancy.
SSM 46085
Service Bulletin/Repair Instructions
The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
SSM 46076
Service Bulletin/Repair Instructions
Some 2016 Model Year Fusion, MKZ and C-MAX Hybrid Electric Vehicles(HEV) vehicles equipped with 2.0L DOHC Gas/Electric engines may exhibit MIL On with Diagnostic Trouble Code P0137(O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2) in Powertrain Control Module(PCM) memory and U3003 (Battery Voltage) in Battery Energy Control Module(BECM) memory due to low battery voltage. Perform Battery diagnostic tests referenced in Workshop Manual Section 414-01 Battery, Mounting and Cables-Diagnosis and Testing. After repairs for low voltage concern are repaired, clear Diagnostic Trouble Codes. If DTC P0137 and U3003 do not repeat return vehicle to the Customer. If DTC P0137 repeats perform Powertrain Control and Emissions Manual(PCED) diagnostic DW. Engineering is currently investigating this concern.
SSM 46069
Service Bulletin/Repair Instructions
Some 2015-2016 vehicles equipped with 6F50/6F55 transmission Built On 11/2/2015 And Through 2/1/2016 may exhibit no reverse, 3rd and 5th gear and/or DTCs P0715, P0717, P0756 and/or P2701. This may be caused by the direct clutch snap ring out of position and/or damage to the direct clutch hub. The cause of the failure is the Tone Wheel surface putting uneven load on the snap ring. To repair this condition the Tone Wheel (7F283) must be replaced,(also referred to as Direct Clutch Cylinder/Tone wheel) in addition to the Tone Wheel, replace Direct Clutch Hub (7G384), Direct Clutch Return Spring (7F235), Direct Clutch Snap Ring (7C122), TSS Sensor (7M101), Seal Kit (7153) and filter in the kit. Disassemble, clean the transmission and main control to remove metal particles. Refer to WSM, Section 307-01. Use causal part 7F283 and applicable Labor ops from SLTS section 7.
SSM 46022
Service Bulletin/Repair Instructions
WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.
TSB16-0105
Service Bulletin/Repair Instructions
SOME 2013-2016 FUSION, MKZ, AND 2013-2015 C-MAX VEHICLES EQUIPPED WITH AN HF35 TRANSMISSION AND BUILT ON OR BEFORE 8/15/2015 MAY EXHIBIT A THUMPING/RUBBING OR GRINDING NOISE COMING FROM THE TRANSMISSION. THE NOISE MAY BE PRESENT IN ALL GEAR RANGES INCLUDING NEUTRAL WHEN THE VEHICLE IS MOVING, BUT WILL NOT BE PRESENT WHEN THE VEHICLE IS STATIONARY OR IN PARK. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 45926
Service Bulletin/Repair Instructions
2013-2017 FUSION/ESCAPE/MKZ (EXCLUDING 3.7L), 2015-2016 EDGE/EXPLORER (EXCLUDING 3.5L/3.7L), 2015-2016 MKC, AND 2016 MKX VEHICLES (EXCLUDING 3.7L) EQUIPPED WITH ALL WHEEL DRIVE (AWD) MAY EXHIBIT A LEAKING PASSENGER SIDE POWER TRANSFER UNIT (PTU) HALFSHAFT/LINKSHAFT SEAL. THIS MAY BE DUE TO A WORN PTU BUSHING. THE PTU BUSHING CAN NOW BE REPAIRED WITHOUT PTU REPLACEMENT. THE ONLINE WSM IS BEING UPDATED FOR ALL LISTED VEHICLES.REFER TO THE INTERMEDIATE SHAFT BUSHING REMOVAL AND INSTALLATION IN WORKSHOP MANUAL (WSM), SECTION 308-07. THE PROCEDURE IS THE SAME FOR ALL VEHICLES. IF THE PROCEDURE IS NOT PUBLISHED FOR THE VEHICLE BEING SERVICED CHECK THE WSM OF ANOTHER LISTED VEHICLE. BUSHING PART NUMBER IS F2GZ-63600A58A. THE PARTS CATALOG IS BEING UPDATED TO INCLUDE THIS BUSHING.
SSM 45917
Service Bulletin/Repair Instructions
SOME 2016-2017 VEHICLES EQUIPPED WITH SYNC 3 MAY EXPERIENCE THE FOLLOWING CONCERNS; THE GPS NOT TRACKING THE VEHICLE POSITION CORRECTLY, THE VEHICLE LOCATION ARROW ICON SPINNING IN CIRCLES ON THE NAVIGATION SCREEN OR A SPINNING COMPASS ON NON-NAVIGATION VEHICLES. PERFORM THE FOLLOWING PROCEDURE TO RESOLVE. ENTER BEZEL DIAGNOSTICS PER WORK SHOP MANUAL (WSM) SECTION 415-00. SELECT TESTING SETTINGS FROM THE MENU. SCROLL DOWN AND PRESS CLEAR DR CALIB. PERFORM A DRIVE TEST FOR APPROXIMATELY 10 MINUTES, INCLUDE AT LEAST FOUR RIGHT TURNS AND FOUR LEFT TURNS WITH A VEHICLE SPEED OF AT LEAST 25 MPH. CONFIRM THAT GPS POSITION FOR NAVIGATION OR THE COMPASS FOR NON-NAVIGATION VEHICLES IS FUNCTIONING PROPERLY. ENGINEERING IS AWARE OF THIS CONCERN. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.
SSM-45821
Service Bulletin/Repair Instructions
SIRI EYES FREE FUNCTIONAL ISSUES USING BLUETOOTH AND APPLE IOS 9.2 AND 9.2.1
SSM-45815
Service Bulletin/Repair Instructions
AIR CONDITIONING (A/C) INOPERATIVE - DIAGNOSTIC TROUBLE CODE (DTC) P0645
16-0066
Service Bulletin/Repair Instructions
Some 2012-2016 vehicles equipped with a touchscreen navigation system and the language set to Arabic may exhibit a blank screen. This may be the result of the ribbon cables not being fully seated inside the front display interface module (FDIM) or an improper software configuration of the FDIM.
TSB160066
Service Bulletin/Repair Instructions
Touchscreen navigation system - arabic language - blank screen
TSB160058
Service Bulletin/Repair Instructions
Wind or whistle noise froim exterior mirror(s) at highway speed
TSB160045
Service Bulletin/Repair Instructions
2.0L Ecoboost - Fuel odor
LTR3756
Service Bulletin/Repair Instructions
49 CFR Part 579.5 Monthly Communications - January 2016
TSB160001
Service Bulletin/Repair Instructions
49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C
SB-45309
Service Bulletin/Repair Instructions
2015-2016 MKZ AND 2015 MKC INSTRUMENT CLUSTER MESSAGE CENTER ARTIST/TITLE AND TRACK MISSING AND IC NEEDS REPROGRAM WITH LATEST SOFTWARE CALIBRATION *CN
SB-45317
Service Bulletin/Repair Instructions
2016 MKZ,MKC AND MKX: MY LINCOLN MOBILE APP NOT ABLE TO CONNECT TO VEHICLES EQUIPPED WITH DTC U2100 AND/OR U2101 ON VEHICLES WITH TELEMATICS CONTROL UNIT *CN
ASI-45157
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ASI-45158
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.