Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
KC-759
New Trim Codes May Need To Be Reprogrammed Following Engine Replacement With 7/8 Reman Or Complete (Engine With Both New Injectors And Engine Control Module); Possible Uneven Operation/Rough Running At Idle Following EMS Programming With Data Transfer.
KC-750
US10 Emission Engines - Diagnostic Trouble Code ( DTC ) SPN 1231 FMI 9 Troubleshooting.
KC-745
Automated Manual Transmission ( AMT ) I-Shift / mDRIVE - Ribbon Harness Replacement - Speed Sensor Bolts, Possible Fault Codes P1058 - 21 Or MID 130 PID 161 FMI 1
KC-2112
Programming Failure - Chassis With Cummins Engine And An Allison Transmission
KC-2143
(Back Office) - Cruise Control Inoperative After Updating Software VECU5 Without ESP Package (UESP).
KC-2116
NOx Sensor Troubleshooting Guide - US10+OBD13 And Newer Emissions
KC-2131
USE FOR NEW VEHICLES (US21+OBD22 Emissions) - Intermittent Diagnostic Trouble Codes U02A3, U029D, U029E
KC-2158
Selective Catalytic Reduction (SCR) Muffler Troubleshooting Guide - US10+OBD13 And Newer Emissions
KC-2165
DEF Pump Troubleshooting Guide - US10+OBD13 And Newer Emissions
KC-2171
Temperature Sensor Troubleshooting Guide - US10+OBD13 And Newer
KC-714
Mack Chassis - Diagnostic Trouble Codes ( DTC's ) - P020113, P020213, P020313, P020413, P020513, P020613, Cylinders 1 Through 6 Injector A Open Circuit
KC-698
Mack Chassis - Diesel Exhaust Fluid ( DEF ) System Cleaning/Flush After DEF Pump Failure Or System Contamination
KC-699
Mack Chassis - Bendix Vendor Configuration Program ( VCP ) Software Download Information
KC-686
(Back Office Only) Mack Chassis - Cruise Control Inoperative After Disabling The Electronic Stability Program (ESP)
KC-663
Emcon (Spark Assist) Engine Aftertreatment System Troubleshooting Check Sheet - US07 Emissions
KC-648
Mack - PTO Pump Speed Calculator
KC-653
Low Oil Pressure Diagnostic Process For 11 Liter Engines
KC-2169
Low Voltage Disconnect (LVD), Function Description
KC-2170
Electronically Controlled Suspension (ECS) Losing Air Pressure
KC-2172
No Start Condition After Over The Air Programing - VECU5 No Start "Safe State"
KC-2161
DEF Pump Cycling periodically Hours After Key Off
KC-626
Mack Chassis - Vehicles Equipped With An Automated Manual Transmission Model F ( AMT-F, mDrive ), Premium Tech Tool ( PTT ) Gearbox Calibration Failure; Gearbox Calibration Operation Stops And Fails At 33% When Run With Transmission Removed
KC-627
Premium Tech Tool ( PTT ) Training Materials And Support Tools
KC-681
Mack Chassis - Spark Assist Engine Aftertreatment System Troubleshooting Check Sheet - US10 Emissions
KC-2152
Mack Command Steer - Diagnostic Trouble Codes - Electronic Control Unit, Event Information"
KC-11
AMT Gearbox 4320-07-03-01-Transmission And Clutch Pulling Position, Calibration And 4000-07-04-01-Transmission,Calibration(Transmission Removed)Explanations
KC-37
V-MAC - Install Under Windows 2000/XP
KC-7
Electronic Control Unit (ECU) Replacement (EMS, VECU, TECU, LCM) - Programming (Conversion Kit) Requirements When Installing An ECU With A Newer Part Number - US04 To US10 Chassis (9-Pin Diagnostic Connector)
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.