Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SA-038-26a
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued service alert listed below. The changes are noted in Red text. SA-038/26 06/15/26 DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote functions inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status
SSPE1 Warr c
Emissions
Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
8026C Warr c
Emissions
2026 CX-50 Hybrid Battery Label Concern - Emissions Recall 8026C Mazda Motor Corporation has decided to conduct a Voluntary Emissions Recall Campaign on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this Emissions Recall. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the hybrid battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s traction battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
DRW60 Repair a
Service Campaign
Subject: Notification of Dealer Re-Work (DRW60) – 2026MY CX-50 and CX-50 Hybrid - Rear Door Glass Holder Detach Issue Dear Mazda Dealer Colleagues, Mazda Motor Corporation has decided to conduct a Dealer Re-Work on certain 2026MY CX-50 and CX-50 Hybrid vehicles. Please see the description, model, year, and VIN range below. Concern Outline: On certain subject vehicles, the rear door glass holder may detach from the door glass due to improper urethane adhesion. If the glass holder separates from the door glass, a rattling noise may occur, and the door glass may not roll down. Repair Outline: Replace both rear door glass in the vehicle (the rear door quarter glass is not affected).
SA-039-26a
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red text. SA-039/26 06/15/26 Mazda Connect Symptom Troubleshooting DESCRIPTION Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-053-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. SA-006/23 01/23/23 DESCRIPTION Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect clock and/or tire pressures and/or tire pressure missing. This may be caused by: Incorrect calendar entry (month/day/year) after a battery disconnect Infotainment system software update. BCM TPMS unlearn during vehicle storage or transport. Wheel/Tire change REPAIR PROCEDURE This can be corrected by the customer driving the vehicle for a day or two so that the following will occur.
SSPE1 Warr b
Emissions
Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
8026C Warr b
Emissions
2026 CX-50 Hybrid Battery Label Concern - Emissions Recall 8026C Mazda Motor Corporation has decided to conduct a Voluntary Emissions Recall Campaign on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this Emissions Recall. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the hybrid battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s traction battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
DRW60 Dlr Ltr
Service Campaign
Subject: Notification of Dealer Re-Work (DRW60) – 2026MY CX-50 and CX-50 Hybrid - Rear Door Glass Holder Detach Issue Dear Mazda Dealer Colleagues, Mazda Motor Corporation has decided to conduct a Dealer Re-Work on certain 2026MY CX-50 and CX-50 Hybrid vehicles. Please see the description, model, year, and VIN range below. Concern Outline: On certain subject vehicles, the rear door glass holder may detach from the door glass due to improper urethane adhesion. If the glass holder separates from the door glass, a rattling noise may occur, and the door glass may not roll down. Repair Outline: Replace both rear door glass in the vehicle (the rear door quarter glass is not affected).
DRW60 Repair
Service Campaign
Subject: Notification of Dealer Re-Work (DRW60) – 2026MY CX-50 and CX-50 Hybrid - Rear Door Glass Holder Detach Issue Dear Mazda Dealer Colleagues, Mazda Motor Corporation has decided to conduct a Dealer Re-Work on certain 2026MY CX-50 and CX-50 Hybrid vehicles. Please see the description, model, year, and VIN range below. Concern Outline: On certain subject vehicles, the rear door glass holder may detach from the door glass due to improper urethane adhesion. If the glass holder separates from the door glass, a rattling noise may occur, and the door glass may not roll down. Repair Outline: Replace both rear door glass in the vehicle (the rear door quarter glass is not affected).
DRW60 Warr
Other
Subject: Notification of Dealer Re-Work (DRW60) – 2026MY CX-50 and CX-50 Hybrid - Rear Door Glass Holder Detach Issue Dear Mazda Dealer Colleagues, Mazda Motor Corporation has decided to conduct a Dealer Re-Work on certain 2026MY CX-50 and CX-50 Hybrid vehicles. Please see the description, model, year, and VIN range below. Concern Outline: On certain subject vehicles, the rear door glass holder may detach from the door glass due to improper urethane adhesion. If the glass holder separates from the door glass, a rattling noise may occur, and the door glass may not roll down. Repair Outline: Replace both rear door glass in the vehicle (the rear door quarter glass is not affected).
SA-012-26c
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-012/26 04/17/26, 03/04/26 and 02/26/2026 DESCRIPTION Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. Additional symptoms that may occur: Connected Vehicle One Time Passcode (OTP) may fail. Connected Vehicle Remote functions may fail. The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT REPAIR PROCEDURE 1. Verify the concern. 2. Check if any of the following DTCs are stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT
SA-050-26
Service Bulletin/Repair Instructions
DESCRIPTION Some vehicles may continue to display the recall notification "IMPORTANT NOTICE. VIEW VEHICLE STATUS MONITOR FOR DETAILS" on the center display even after the recall has been completed. NOTE: Once the warranty claim for the recall campaign is approved by Mazda Japan, the recall notification will be automatically removed via Connected Services on the following day or later. This condition may occur if the Connected Services subscription was canceled while the recall notification was still active. ACTION TO BE TAKEN If you encounter the situation above, use MDARS to manually remove the center display recall notification. Note: MDARS can only remove the recall notification when MCVV shows no CV contract.
SA-047-26
Service Bulletin/Repair Instructions
Some customers may experience: The fuel fill door will not release until multiple button applications. The gas pump dispenser/nozzle is clicking off during refueling before the tank is full and it may take 1/2 to 1 gallon at a time. Check engine light on with DTCs. REPAIR PROCEDURE 1. Verify the customer concern. 2. Replace the evaporative shut valve according to the WSM on MGSS (FUEL SHUT-OFF VALVE REMOVAL/INSTALLATION [CW]).
8026C Warr a
Emissions
2026 CX-50 Hybrid Battery Label Concern - Emissions Recall 8026C Mazda Motor Corporation has decided to conduct a Voluntary Emissions Recall Campaign on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this Emissions Recall. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the hybrid battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s traction battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SSPE1 Warr a
Emissions
Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SA-043-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-063/24 09/06/24 DESCRIPTION The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction.
16-010-26
Service Bulletin/Repair Instructions
COMPLIANCE WITH NEW YORK STATE GENERAL BUSINESS LAW §399‑CCCCC (CONNECTED VEHICLE SERVICE; DOMESTIC VIOLENCE VICTIMS) DESCRIPTION This Service Information is issued in accordance with New York State General Business Law §399CCCCC (Connected Vehicle Service; Domestic Violence Victims). This regulation is intended to protect victims of domestic violence by allowing them to request the termination of third-party access (including access by an alleged abuser) to connected vehicle services, such as vehicle location tracking and remote control functions. To support this requirement, this Service Information enables confirmation of whether a vehicle is subject to connected vehicle services by referring to the SUBJECT VIN & PRODUCTION DATE RANGE, and provides guidance on the procedure to terminate such services when a customer requests the removal of third-party access for an applicable vehicle. Effective July 1, 2026, if a customer requests action under this regulation, a CMU/CDC software update must be performed to enable appropriate control of connected vehicle service access. If no request is made by the customer, the CMU/CDC software update is not required. REPAIR PROCEDURE 1. Confirm that the customer has requested deactivation of connected services in accordance with New York State General Business Law related action. 2. Perform the CMU/CDC software update according to the procedures outlined in the appropriate TSB shown in the table below:
SA-042-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SAs listed below. The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out
16-001-26a
Service Bulletin/Repair Instructions
UPDATED SOFTWARE RELEASE FOR CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 16-001/26 01/08/26 DESCRIPTION The release notes outlined below provide an overview of bug fixes, feature improvements, and updates included in the latest software release. The latest version of software contains all the updates of the previous versions. NOTE: If current version is not 7230C1A-NA01_***** or 7230C2A-NA01_*****, this TSB is not applicable. Version 7230C1A-NA01_10022 enables termination of connected services at customer request: Termination of Connected Services by customers at their initiative has been enabled. Accordingly, the following items have been updated. Add a "Data Communication Information" item under Settings > System Settings>Online Connectivity. ○ Updated the text displayed on the confirmation screen for disabling Connected Services. ○ • The list on the center display may appear distorted, giving a double image. • The system may reboot when the ignition is turned on. However, the camera images on the center display are not affected, and the back camera is usable. • The voice recognition function does not start. • Apple CarPlay® may fail to connect while driving on the highway. REPAIR PROCEDURE 1. Verify the customer concern. 2. Update MAZDA CONNECT with software version 7230C1A-NA01_10022/7230C2A-NA01_10014 or later with a USB memory stick using the 7TH GEN MAZDA CONNECT Update Instructions.
16-002-26a
Service Bulletin/Repair Instructions
UPDATED SOFTWARE RELEASE FOR CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 16-002/26 01/12/26 DESCRIPTION The release notes outlined below provide an overview of bug fixes, feature improvements, and updates included in the latest software release. The latest version of software contains all the updates of the previous versions. NOTE: If current version is not 7230C1A-NA02_***** , this TSB is not applicable. Version 7230C1A-NA02_10022 enables termination of connected services at customer request and fixes these software errors (bugs): Termination of Connected Services by customers at their initiative has been enabled. Accordingly, the following items have been updated. Add a "Data Communication Information" item under Settings > System Settings>Online Connectivity. ○ Updated the text displayed on the confirmation screen for disabling Connected Services. ○ • The list on the center display may appear distorted, giving a double image. • The system may reboot when the ignition is turned on. However, the camera images on the center display are not affected, and the back camera is usable. • The voice recognition function does not start. • Apple CarPlay® may fail to connect while driving on the highway. REPAIR PROCEDURE 1. Verify the customer concern. 2. Update MAZDA CONNECT with software version 7230C1A-NA02_10022 or later with a USB memory stick using the 7TH GEN MAZDA CONNECT Update Instructions.
SA-028-26a
Service Bulletin/Repair Instructions
DESCRIPTION Some vehicles may exhibit a clicking, popping, tapping or knocking noise from the front end when turning left or right and accelerating. NOTE: The noise could occur at different steering wheel angles or power levels. Due to the insulating properties of the suspension and chassis, it can be difficult to determine which driveshaft is at fault by listening from inside the vehicle. See the attached video for an example of an outer CV joint clicking. These noises may be caused by the outer ball joint cage machining being out of specification. To eliminate this concern, tighter quality controls have been implemented to ensure proper machining of the cage window. NOTE: The part number for the improved part has not been changed. The current parts inventory is after the countermeasure production date implementation.
SA-041-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
SA-027-26a
Service Bulletin/Repair Instructions
This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-027/26 04/16/26 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. REPAIR PROCEDURE 1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda DCA-8000 Instruction Manual for more information.
SA-0-38/26
Service Bulletin/Repair Instructions
DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status
SA-039-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA listed below. The changes are noted in Red text. SA-012/25 10/06/25, 08/21/25, 05/15/25 and 02/27/25 DESCRIPTION Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE NOTE: Before proceeding: Document the vehicle's current MAZDA CONNECT CMU software version. • 2019-2022 Models - Go to TSB 16-003/23 and confirm the CMU Serial Number is not within the affected range. • Document customer device Brand/Model/Model Number/software version on the repair order. • Confirm that the Connectivity Master Unit (CMU) is updated to the latest software version. Go to MGSS -> Infotainment -> MAZDA CONNECT Updates ○ • If possible, complete the Microsoft Forms Questionnaire. Go to MGSS -> Infotainment -> MAZDA CONNECT Questionnaire.
SA-040-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-009/25 08/22/25 and 02/18/25 DESCRIPTION Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs. Index System Outline • MYMAZDA App Connected Vehicle (CV) Error Codes • Vehicle Confirmation Instructions • Troubleshooting Instructions • Resources
SA-037-26a
Service Bulletin/Repair Instructions
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. SA-037/26 05/28/26 DESCRIPTION Replacement battery packs for High Voltage systems are supplied with an additional label that matches the one attached to the service battery pack (refer to the sample High Voltage Battery Label image for reference). When replacing the battery pack in a 2026 or later model that has a similar label at the base of the left B-pillar, replace the label with the new one included in the service parts battery pack. REPAIR PROCEDURE Label Application: When replacing a High Voltage Battery: refer to the Label Application Process included in the "HIGH VOLTAGE BATTERY REMOVAL/INSTALLATION" or "M Hybrid Boost BATTERY REMOVAL/INSTALLATION" procedures in the Workshop Manual for the applicable models.
SSPE1 Repair a
Service Campaign
Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
8026C Repair a
Emissions
2026 CX-50 Hybrid Battery Label Concern - Emissions Recall 8026C Mazda Motor Corporation has decided to conduct a Voluntary Emissions Recall Campaign on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this Emissions Recall. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the hybrid battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s traction battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
8026C SSPE1 Dlr Ltr a
Emissions
Attention: Mazda Sales, General, Parts and Service Managers Subject: Announcement of Emissions Recall 8026C and Special Service Program SSPE1 - Battery Label Concern - 2026MY CX-50 Hybrid vehicles Dear Mazda Dealer Colleagues, Mazda Motor Corporation has decided to conduct an Emissions Recall and Special Service Program on certain 2026MY CX-50 Hybrid vehicles sold in the U.S. Please see the description, model, year, and VIN range below for all vehicles in these campaigns. There are 612 vehicles affected by Emission Recall 8026C and 1,997 vehicles affected by Special Service Program SSPE1. There are 2,609 total vehicles affected by these two concerns. Subject Vehicles: Model Subject VIN range Subject production date range 2026MY CX-50 Hybrid 7MM VA**** TN 142667 – 145555 From September 8, 2025 through September 26, 2025 **Only VIN’s in this range and with an “OPEN” status in eMDCS are affected. The subject VIN and production date ranges are based on all the subject vehicles regardless if the vehicle is in the Emissions recall or SSP. Emissions Recall 8026C: On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the hybrid battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s traction battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Special Service Program SSPE1: On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. Repair Outline, Photo Requirement and Label Ordering: For both campaigns, attach two labels to each vehicle; one on the B-pillar and the other on the hybrid battery beneath the rear seat. • Label Kit Ordering: The part used in this campaign is not ordered from the Dealer Assistance Group (DAG). The label kit is ordered from eSTORE via a specific procedure outlined in the Parts & Warranty information. Please follow detailed instructions in the document on how to order the labels. Each order will appear in your dealers list of eSTORE orders and be shipped overnight delivery free of charge. • AVIS rental vehicles in SSPE1: This SSP includes approximately 900 vehicles owned by AVIS rental car. All AVIS repair facilities are authorized to do this repair, but if a vehicle is at your Mazda dealer for a different warranty repair, the SSP can be completed. • VITALLY IMPORTANT: All warranty claims will be manually reviewed. There are 3 required photos that must be submitted with each warranty claim exactly as specified in the repair procedure. Claims with incorrect photos will require a re-repair at the dealer’s expense.
8026C CV Notification
Emissions
2026 CX-50 Hybrid Battery Label Concern - Emissions Recall 8026C Mazda Motor Corporation has decided to conduct a Voluntary Emissions Recall Campaign on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this Emissions Recall. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the hybrid battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s traction battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SA-033-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued SA(s) listed below. The changes are noted below in Red. SA-029/25 10/16/25 and 06/02/25 DESCRIPTION This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure. REPAIR PROCEDURE HIGH VOLTAGE BATTERY MAINTENANCE Verify the State-of-charge (SOC) in the instrument cluster. MX-30 EV: If the SOC is lower than 26%, charge it to 50% (either by normal charging or quick charging). CX-90/CX-70 PHEV: If the SOC is lower than 1%, charge it to 10% (either by normal charging, quick charging or engine running).
SA-037-26
Service Bulletin/Repair Instructions
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. SA-049/25 10/16/2025 DESCRIPTION Replacement battery packs for High Voltage systems are supplied with an additional label that matches the one attached to the service battery pack (refer to the sample High Voltage Battery Label image for reference). When replacing the battery pack in a 2026 or later model that has a similar label at the base of the left B-pillar, replace the label with the new one included in the service parts battery pack. REPAIR PROCEDURE Label Application: When replacing a High Voltage Battery: refer to the Label Application Process included in the "HIGH VOLTAGE BATTERY REMOVAL/INSTALLATION" or "M Hybrid Boost BATTERY REMOVAL/INSTALLATION" procedures in the Workshop Manual for the applicable models. In addition to the procedures outlined in the Workshop Manual, please follow these additional steps when removing an existing label to help simplify the application of the new one:
SSPE1 Owner Ltr
Emissions
Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SSPE1 Repair
Emissions
Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SSPE1 Warr
Emissions
Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
09-014-26
Service Bulletin/Repair Instructions
Some vehicles may experience intermittent battery discharge. This may be caused by improperly installed door boots allowing water to enter into the central connectors C-22/C-23 (located near the A-pillar at the base of the left and right front doors), leading to corrosion in the connector. REPAIR PROCEDURE Replace the rear harness and the affected door harness with new ones, making sure to properly install the door boots.
SA-031-26
Service Bulletin/Repair Instructions
DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
SA-008-26a
Service Bulletin/Repair Instructions
During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern. REPAIR PROCEDURE Check the rear bumper for an indentation. Repair bumper.
SA-012-26b
Service Bulletin/Repair Instructions
Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. Additional symptoms that may occur: Connected Vehicle One Time Passcode (OTP) may fail. • Connected Vehicle Remote functions may fail. • The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) • U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT REPAIR PROCEDURE 1. Verify the concern. 2. Check if any of the following DTCs are stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) • U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT Are the following DTCs stored? YES: Proceed to next step. • NO: This service information does not apply. Continue troubleshooting using MGSS. • 3. Check for electrical devices in the vehicle such as a device connected to USB hub, Dash Cam, Insurance Device, FasTrak........ect. Are there any customer electrical devices in the vehicle? YES: Document customer device used, then go to the next step. • NO: Go to the next step. • 4. Clear the DTC's
SA-028-26
Service Bulletin/Repair Instructions
DESCRIPTION Some vehicles may exhibit a clicking, popping, tapping or knocking noise from the front when turning left or right and accelerating. NOTE: The noise could occur at different steering wheel angles or power levels. Due to the insulating properties of the suspension and chassis, it can be difficult to determine which driveshaft is at fault by listening from inside the vehicle. See the attached video for an example of an outer CV joint clicking. Repair Procedure: Replace the affected driveshaft after confirming the source of the noise using chassis ears. Both driveshafts may be faulty; verify each side before replacement.
SA-027-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts.
SA-014-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) and TSB(s) listed below: The changes are noted in Red. SA-035/24 05/31/24 DESCRIPTION There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not. A mechanical seal (A) is used for the water pump. This mechanical seal can seal coolant (B) by sliding a mating ring (C) against a seal ring (D). When the sliding surface temperature of the mechanical seal is more than 248 °F (120 °C) while driving, a small amount of steam (E) is leaked and bleeds through the bleeding hole (F). After drying, the steam leaves a green coolant deposit near the water pump bleed hole (F). This is a normal condition and does not require water pump replacement. The water pump should only be replaced if there is an accumulation of crystallized coolant near the bleed hole. When you encounter a water pump with coolant seepage marks, decide to replace it or not based on the following criteria using sample photos. NOTE: During the initial period of use*, the sliding surfaces of the seals may not yet be fully settled, which can temporarily increase the amount of leakage. Continued use will allow the surfaces to settle, reducing the leakage. Replacing parts that are already settled with new ones will increase the leakage again until the new parts become conditioned. Therefore, replacement should be avoided in this initial period of use. *As a guideline, this applies to vehicles with less than 1,860 miles (3000 km) of mileage.
SA-012-26a
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-012/26 02/26/2026 DESCRIPTION Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. Additional symptoms that may occur: Connected Vehicle One Time Passcode (OTP) may fail. Connected Vehicle Remote functions may fail. The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT REPAIR PROCEDURE 1. Verify the concern. 2. Check if any of the following DTCs are stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT Are the following DTCs stored? YES: Proceed to next step. NO: This service information does not apply. Continue troubleshooting using MGSS. 3. Check for electrical devices in the vehicle such as a device connected to USB hub, Dash Cam, Insurance Device, FasTrak........ect. Are there any customer electrical devices in the vehicle? YES: Document customer device used, then go to the next step. NO: Go to the next step. 4. Check for a Navi SD Card. Is the vehicle equipped with a Navi SD Card? YES: Replace the Navi SD Card. NO: Go to next step. 5. Complete the Dealer Connected Vehicle Questionnaire. 6. Collect CMU log data. Go to Infotainment/TCU --> Collecting CMU Log Data --> CMU Log Data Retrieval Instructions 7. Collect TCU log data. Go to Infotainment/TCU --> TCU Log Data Retrieval Instructions --> CMU Log Data Retrieval Instructions 8. Contact Hotline for additional assistance. 9. Release the vehicle to the customer. NOTE: This concern is currently under investigation
SA-012-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-060/25 12/16/25 Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. Additional symptoms that may occur: Connected Vehicle One Time Passcode (OTP) may fail. Connected Vehicle Remote functions may fail. The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT
SA-008-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-041/25 10/31/25 and 09/10/25 During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern.
SA-005-26
Service Bulletin/Repair Instructions
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit codes. • Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. • For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.
SA-004-26
Service Bulletin/Repair Instructions
Some customers may complain that a door beltline molding is loose, fell off, or is missing.
09-001-26
Service Bulletin/Repair Instructions
There are wrinkles on the leather seat cushion and/or seat back surface at PDI, when new vehicle is delivered, or when new upholstery is installed under Warranty repair. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal usage.
SA-002-26
Service Bulletin/Repair Instructions
Some customers may complain that the tire sidewalls are distorted or "damaged". Sidewall waviness/indentations/undulations are common on radial tires and are more noticeable on tires with taller sidewalls. The higher the tire pressure, the more noticeable the effect will be. Be sure to set the tire pressures at the recommended tire pressure on the vehicle tire label. Sidewall indentations are a cosmetic condition that does not affect the performance of the tires.
SA-001-26
Service Bulletin/Repair Instructions
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
SA-017-25d
Service Bulletin/Repair Instructions
Mazda Connect Services - Frequently Asked Questions (FAQ)
SA-060-25
Service Bulletin/Repair Instructions
Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) • U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT
SA-061-25
Service Bulletin/Repair Instructions
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
SA-023-25c
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop • Door Lock / Unlock • Lights ON / OFF • Climate Control • 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Page
SA-045-25a
Service Bulletin/Repair Instructions
If all keys are lost and the technician is attempting to scan a vechile without ignition on, two options can be used to scan the vehicle: a PCM software number is requested in MDARS and must be inputted or ID another CX-50 and check the PCM in the network screen.
SA-056-25
Service Bulletin/Repair Instructions
When inspected, the differential or PTO oil is dark or black. This is considered normal and NO repair should be performed. During production, differential ring and pinion gears receive a manganese phosphate coating (commonly referred to as black oxide). This coating forms a porous, oil-retentive surface that improves boundary lubrication and reduces adhesive wear during initial contact cycles. Designed as a sacrificial layer, it is gradually removed under load throughout the break-in process. As a result, after the first few hundred miles, or at the initial gear oil service interval, the lubricant may appear darkened by the worn-off coating. It will contain trace ferrous particles from the normal run-in of the gear teeth and bearing surfaces. This condition is expected and does not, by itself, indicate an issue with the differential or PTO gears.
SA-055-25
Service Bulletin/Repair Instructions
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.
SA-020-25a
Service Bulletin/Repair Instructions
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
09-010-25b
Service Bulletin/Repair Instructions
Some customers may complain about a rattle from the sunroof (panorama roof) area. Make sure to read the complete repair procedure before attempting any repairs as the sunroof may have rattles from more than one location. The rattle noise may be caused by: Looseness in the side cover fitting part 1. Looseness in the cross brace cover clip 2. Looseness in the movable part inside the sunroof unit 3. To eliminate this concern, the following changes have been implemented. CAUSE 1: The shape of the side cover and clips have been modified to reduce the movement causing the rattle noise CAUSE 2: Improvement of the assembly process CAUSE 3: Modification of dimensions of the moving parts
SA-051-25
Service Bulletin/Repair Instructions
Noise, Vibration, and Harshness (NVH) Diagnostic Guidelines Diagnostic Guidelines When diagnosing NVH concerns, it is essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.
SA-052-25
Service Bulletin/Repair Instructions
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.
01-006-25
Service Bulletin/Repair Instructions
On some vehicles, the engine oil appears to be milky white during engine oil inspection or replacement. This is caused by moisture in the blow-by gas mixing with the engine oil when driving repeatedly for short distances in extremely low temperatures. NOTE: Inform the customer that the vehicle engine needs to to warm up to normal operating temperature in extremely cold temperatures to remove the moisture in the engine. Oil change will be covered one time only under Warranty. Customers having this concern should have their vehicle repaired using the following repair procedure.
SA-007-25b
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery.
SA-029-25a
Service Bulletin/Repair Instructions
This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
SA-049-25
Service Bulletin/Repair Instructions
Replacement battery packs for High Voltage systems are supplied with an additional label that matches the one attached to the service battery pack (refer to the sample High Voltage Battery Label image for reference). When replacing the battery pack in a 2026 or later model that has a similar label at the base of the left B-pillar, replace the label with the new one included in the service parts battery pack.
SA-012-25c
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-044-25
Service Bulletin/Repair Instructions
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
SA-046-25
Service Bulletin/Repair Instructions
Some engine components like the timing chain cover and oil pan on the CX-50 Hybrid require the use of Threebond 1207B during installation. This sealant should be locally sourced when needed. NOTE: The following link is provided as a convenient sourcing option. https://www.amazon.com/Three-Bond-Performance-Adhesion-Gasket/dp/B008BYPRRI
SA-042-25
Service Bulletin/Repair Instructions
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.
SA-043-25
Service Bulletin/Repair Instructions
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.
SA-017-25c
Service Bulletin/Repair Instructions
Mazda Connected Services - Frequently Asked Questions
SA-009-25a
Service Bulletin/Repair Instructions
Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.
SA-023-25b
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
SA-039/25
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.
SA-012-25b
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.