Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SA-041-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
SA-026-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
09-005-26
Service Bulletin/Repair Instructions
If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. In most cases, if the left-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" can be completed without any problem (See CAUTION below for more details). Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails “BSM OFF" indicator ON Center Display warning message BSM failsafe (No operation) DTC U3000:54 stored in memory DTC U1A4B:54 stored in memory (CX-3, MX-5 only) NOTE: Since a new BSM control module does not retain the vehicle specification information, it is necessary to acquire and store the vehicle specification information transmitted via CAN communication from the combination meter through automatic configuration after replacement.
SA-061-25
Service Bulletin/Repair Instructions
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
CSP13d Dealer Ltr
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
SA-031-25
Service Bulletin/Repair Instructions
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
CSP13c Dealer Ltr
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
SA-007-25a
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result
CSP13a Parts and Warranty
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
CSP13b Dealer Ltr
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
CSP13a Dealer Ltr
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
CSP13 Dealer Letter
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
CSP13 FAQs
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
CSP13 Parts and Warranty
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
CSP13 Repair
Warranty Program/Extension
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
SA-020-25
Service Bulletin/Repair Instructions
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
09-009-25
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display: Center display touchscreen operates by itself (Ghost Touch). • The film of the center display may be peeled off. • White dots may appear on the center display. • Spider web-like cracking appearing in the corner(s) of the MAZDA CONNECT center display (the cracks are internal and cannot be felt by touch).
SA-007-25
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
CSP12 Parts Warr
Warranty Program/Extension
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
CSP12 Repair MX5
Warranty Program/Extension
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
CSP12 FAQs
Warranty Program/Extension
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
CSP12 Dealer Letter
Warranty Program/Extension
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
SA-079-24
Service Bulletin/Repair Instructions
The SKYACTIV-DRIVE FW6A-EL AT uses “Automatic Transmission Fluid (ATF) Type: FZ”. Only use “ATF-FZ” to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
SA-057-24
Service Bulletin/Repair Instructions
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
SA-058-24
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
SA-053-24
Service Bulletin/Repair Instructions
Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
09-038-24
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
SA-011-24b
Service Bulletin/Repair Instructions
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
SA-022-24a
Other
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
SA-032-24
Other
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
SA-027-24
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
SA-022-24
Service Bulletin/Repair Instructions
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
09-003-23b
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display: Center display touchscreen operates by itself (Ghost Touch). The film of the center display may be peeled off. White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts.
01-007-23a
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
SA-032-23a
Service Bulletin/Repair Instructions
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
SA-039-23a
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
SA-039-23
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
09-025-23
Service Bulletin/Repair Instructions
Some customers may complain that the frequency of replenishing the window washer liquid is higher than expected, or they may complain of leakage at or around the washer motor (1). This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section. This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.
SA-032-23
Service Bulletin/Repair Instructions
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
SA-031-23
Service Bulletin/Repair Instructions
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
01-007-23
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
SA-016-23
Service Bulletin/Repair Instructions
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method
SA-012-23
Service Bulletin/Repair Instructions
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
RF-23-01
Service Bulletin/Repair Instructions
When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.
09-003-23a
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. - White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.
RF-22-01R3
Service Bulletin/Repair Instructions
This Parts Flash replaces RF-22-01R2 released January 04, 2022. It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.
SA-001-23a
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.
RF-22-01R2
Service Bulletin/Repair Instructions
This Parts Flash replaces RF-22-01R released November 21, 2022. It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.
09-003-23
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. - White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.
SA-001-23
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.
SA-016-22a
Service Bulletin/Repair Instructions
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
09-018-22b
Service Bulletin/Repair Instructions
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.324 or later). The system performance has been improved as follows: Ver. 74.00.324 fixes these software errors (bugs): * If the shift lever is operated quickly while displaying the CarPlayTM screen, the rear view screen may not return to the CarPlayTM screen. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into the R position.
SA-041-22c
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display: * Ghost Touch * DTC B108E:04 may be stored (Touch screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White dots
22-01R
Service Bulletin/Repair Instructions
Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Please use the table below when ordering the screen repair kits. This can also be found in Service Alert SA-041/22.
SA-075-22
Service Bulletin/Repair Instructions
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple CarplayâÃÂâ/ Android AutoâÃÂâ will not connect) 6. Over-sized wheels/tires (incorrect GPS location)
SA-008-22a
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
SA-068-22
Service Bulletin/Repair Instructions
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
09-041-22
Service Bulletin/Repair Instructions
If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. Other possible symptoms that may be found if the right-side BSM module is replaced alone: * BSM aiming fails * "BSM OFF" indicator ON * Center Display warning message * BSM failsafe (No operation) * DTC U3000:54 stored in memory * DTC U1A4B:54 stored in memory (CX-3, MX-5 only)
01-012-22
Service Bulletin/Repair Instructions
Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush.
RF-22-01
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display ghost touch (touch screen operates by itself), surface peeling or spider cracks. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.
09-036-22
Service Bulletin/Repair Instructions
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. - White dots may appear on the center display
09-017-22a
Service Bulletin/Repair Instructions
Some vehicles may have rust on the contact parts between the clips (for attaching the roof molding) and the roof panel (ditches of the roof rail). This is caused by the gap between the roof molding attachment clips and the roof panel not being wide enough to allow paint to be appropriately applied to the roof panel. To eliminate this concern, the shape of the roof molding clip has been changed to enable paint application between the clip's rib and roof during the manufacturing process.
SA-006-22a
Service Bulletin/Repair Instructions
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
SA-006-22
Service Bulletin/Repair Instructions
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
SA-008-22
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
09-021-21-3818b
Service Bulletin/Repair Instructions
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of MazdaâÂÂs continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.
05-001-21-3826
Service Bulletin/Repair Instructions
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.
09-025-21-3824
Service Bulletin/Repair Instructions
This service bulletin provides information regarding the proper use of the driverâÂÂs floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.
09-021-21-3818a
Service Bulletin/Repair Instructions
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.
09-022-21-3815
Service Bulletin/Repair Instructions
Some customers may complain that the frequency of replenishing the window washer liquid is higher than expected, or they may complain of leakage at around the washer motor (1).This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.
09-021-21-3818
Service Bulletin/Repair Instructions
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of MazdaâÂÂs continuing efforts to improve safety and reduce driver distraction.
SA-040-21
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
MT-003-21
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.
SA-032-21
Service Bulletin/Repair Instructions
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
01-005-21-3778
Service Bulletin/Repair Instructions
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
01-006-21-3779
Service Bulletin/Repair Instructions
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
09-002-21-3770
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer
MT-005-20
Service Bulletin/Repair Instructions
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? ïÃÂ÷ Yes - No repair is necessary. ïÃÂ÷ No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).
01-012-20-3738
Service Bulletin/Repair Instructions
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone.ï· P2096:00 - Air fuel too lean ï· P2097:00 - Air fuel too rich ï· P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
07-004-20-3741
Service Bulletin/Repair Instructions
Some customers may complain that the air conditioner (A/C) is not cooling. This may be caused by a refrigerant leak from the condenser due to corrosion where an anti-corrosion coating was uneven.
02-005-20-3688
Service Bulletin/Repair Instructions
Some customers may complain about a knocking noise heard from the rear suspension while driving on rough road. The noise may be caused by a broken bound (bump) stopper that breaks because of deterioration from environmental factors and bad road conditions. To eliminate this concern, a dust boot has been added in order to protect the bound (bump) stopper from water and the mounting rubber has been changed accordingly.
09-006-20-3673a
Service Bulletin/Repair Instructions
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
04-006-20-3707
Service Bulletin/Repair Instructions
Some customers may experience a TCS/DSC warning light and SCBS warning light (amber) illumination with DTC C0051:62 stored in PCM memory. DTC C0051:62 - EPS control module[when the vehicle is driven in a straight line, the difference between the steering angle (calculated by each sensor) and the steering angle (from the steering angle sensor) is greater than the specification]. This concern most likely occurs during the following situations: When the vehicle is turning in reverse, right after starting the engine. When the vehicle is going over a bump or a curb, right after starting the engine. This concern may be caused when the DSC HU/CM performs the steering center position calibration. During the learning process, if a shock is applied to the vehicle by a bump or curb etc., the steering center position may not be properly detected and creates a steering center position error. To eliminate this concern, the DSC HU/CM control software has been modified
09-003-20-3671
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealerâÂÂs responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. ï· Mazda vehicles are manufactured with tamper-proof speedometers. ï· When a speedometer is replaced, the new speedometer will read zero (0) miles. ï· This procedure is extremely important to accurately represent actual vehicle mileage. ï· Prior to speedometer removal, complete the information required on the âÂÂSpeedometer Replacement LabelâÂÂ. Labels can only be ordered through Mazda eStore. ï· In an effort to achieve a higher level of Customer Experience and retain the value of MazdaâÂÂs vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOâÂÂs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
02-007-19-3645
Service Bulletin/Repair Instructions
Some vehicles may exhibit corrosion of the wheel nuts. This is caused by torsional stress concentrating on the tip of the wheel nut because of the thin and long shape of the nut, which damages the coating and causes the corrosion. To correct this issue, the width across the flats of the wheel nuts have been changed from 17mm to 21mm.
MT-002-19
Service Bulletin/Repair Instructions
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
MT-003-19
Service Bulletin/Repair Instructions
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
09-010-19-3624
Service Bulletin/Repair Instructions
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3) where attachment bolt (4) is seated. After installing the bolt (4), apply touch-up paint to the exposed base material area of the front fender stay.
09-031-19-3625
Service Bulletin/Repair Instructions
After the installation of a new instrument cluster, the message "Fctry" or âÃÂÃÂFactoryâÃÂàis displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required. NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.
02-003-19-3547
Service Bulletin/Repair Instructions
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
MT-012-18
Service Bulletin/Repair Instructions
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?
SA266
Service Bulletin/Repair Instructions
MAZDA Mobile start (MMS) cannot communicate with vehicle