09-024-22
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer.
Vehicle report
1998 MAZDA MIATA
Service bulletins
54 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
01-006-22
Service Bulletin/Repair Instructions
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
SA-014-22
Service Bulletin/Repair Instructions
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories.
01-003/22
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
01-006-21-3779b
Service Bulletin/Repair Instructions
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
05-002-21-3854
Service Bulletin/Repair Instructions
Automatic Transmission/Transaxle Cooler and Lines Flushing Procedure: Automatic Transaxle/Transmission (A/T) oil cooler and lines must be power flushed completely before an overhauled or replacement A/T is installed (except SKYACTIV-DRIVE). The most common cause of repeat A/T failures is lack of lubrication to the front and rear planetary gears. This is usually caused by an accumulation of metal particles and debris (from a previous A/T failure) on the internal mesh type baffle of the oil cooler. Power flushing will remove the restriction by back flushing, followed by forward flushing to dislodge a restriction, then back flushing again. This will in turn ensure full ATF flow for the transmission when it is operating.
01-006-21-3779a
Service Bulletin/Repair Instructions
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
09-025-21-3824
Service Bulletin/Repair Instructions
This service bulletin provides information regarding the proper use of the driverâÂÂs floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.
SA-041-21
Service Bulletin/Repair Instructions
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions
01-005-21-3778
Service Bulletin/Repair Instructions
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
01-006-21-3779
Service Bulletin/Repair Instructions
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
09-002-21-3770
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer
09-003-20-3671
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealerâÂÂs responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. ï· Mazda vehicles are manufactured with tamper-proof speedometers. ï· When a speedometer is replaced, the new speedometer will read zero (0) miles. ï· This procedure is extremely important to accurately represent actual vehicle mileage. ï· Prior to speedometer removal, complete the information required on the âÂÂSpeedometer Replacement LabelâÂÂ. Labels can only be ordered through Mazda eStore. ï· In an effort to achieve a higher level of Customer Experience and retain the value of MazdaâÂÂs vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOâÂÂs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
00-003-19-3583
Service Bulletin/Repair Instructions
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
09-009-19-3566
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
01-004-19-3558
Service Bulletin/Repair Instructions
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
09-002-19-3554
Service Bulletin/Repair Instructions
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.
01-001-19-3551
Service Bulletin/Repair Instructions
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
01-002-19-3552
Service Bulletin/Repair Instructions
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps):CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery's Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda GR8-1291, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries.
00-001-18-3446a
Service Bulletin/Repair Instructions
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
00-003-18-3480a
Service Bulletin/Repair Instructions
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.
09-014-18-3443a
Service Bulletin/Repair Instructions
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
09-034-18-3430a
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
01-016-18-3522
Service Bulletin/Repair Instructions
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
09-034-18-3430
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
00-003-18-3480
Service Bulletin/Repair Instructions
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.
01-008-18-3451
Service Bulletin/Repair Instructions
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
01-009-18-3452
Service Bulletin/Repair Instructions
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
09-019-18-3450
Service Bulletin/Repair Instructions
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.
00-001-18-3446
Service Bulletin/Repair Instructions
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
09-014-18-3443
Service Bulletin/Repair Instructions
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
09-035-17-3080
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
0000216
Service Bulletin/Repair Instructions
Mazda guidelines for factory scheduled maintenance
0901216
Service Bulletin/Repair Instructions
Paint damage Mazda pocket paint guide
0900716
Service Bulletin/Repair Instructions
Speedometer replacement procedure
0100316
Service Bulletin/Repair Instructions
SULFUR SMELL FROM EXHAUST SYSTEM.
0100416
Service Bulletin/Repair Instructions
Battery Maintenance
0100516
Service Bulletin/Repair Instructions
Battery test procedure requirements using the GR81291
0900416
Service Bulletin/Repair Instructions
PROPER USAGE OF DRIVER'S FLOOR MAT.
09-034-14-2956
Service Bulletin/Repair Instructions
IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
00-002-14-2936
Service Bulletin/Repair Instructions
MAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.
09-027-14-2935
Service Bulletin/Repair Instructions
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
00-001-13-2748A
Service Bulletin/Repair Instructions
MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.
09-005-13-2781
Service Bulletin/Repair Instructions
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTEN-TIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE.FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION.INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED.FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
00-001-13-2748
Service Bulletin/Repair Instructions
MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.
00-004-12-2741
Service Bulletin/Repair Instructions
MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.
00-004/12
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
00204
Service Bulletin/Repair Instructions
EVAPORATIVE EMMISSIONS AND RECIVER ADAPTERS. *EH
0102504
Service Bulletin/Repair Instructions
BATTERY TEST PROCEDURE REQUIREMENTS. *TT
0902604
Service Bulletin/Repair Instructions
SPEEDOMETER REPLACEMENT PROCEDURE. *TT
00700
Service Bulletin/Repair Instructions
CIGARETTE LIGHTER DOES NOT WORK OR STAY IN POSITION. *TT
01299
Service Bulletin/Repair Instructions
SUBJECT REGARDING PAINT DAMAGE - IRON PARTICLES / INDUSTRIAL FALLOUT / ACID RAIN. *TT
00798
Service Bulletin/Repair Instructions
CONCERNS OF PAINT DAMAGE OCCURING ON THE BODY AT THE REAR CORNERS OF THE TRUNK OPENING. *TT
97102302097
Service Bulletin/Repair Instructions
PRE-PAINTING PREPARATIONS FOR FRONT AND REAR BUMPERS. *YC
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.