Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SA-038-26a
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued service alert listed below. The changes are noted in Red text. SA-038/26 06/15/26 DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote functions inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status
SA-039-26a
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red text. SA-039/26 06/15/26 Mazda Connect Symptom Troubleshooting DESCRIPTION Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-053-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. SA-006/23 01/23/23 DESCRIPTION Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect clock and/or tire pressures and/or tire pressure missing. This may be caused by: Incorrect calendar entry (month/day/year) after a battery disconnect Infotainment system software update. BCM TPMS unlearn during vehicle storage or transport. Wheel/Tire change REPAIR PROCEDURE This can be corrected by the customer driving the vehicle for a day or two so that the following will occur.
09-023-26
Service Bulletin/Repair Instructions
DESCRIPTION Some customers may complain that the Adaptive LED Headlights (ALH) aim upward for several seconds just before the vehicle comes to a stop during nighttime driving. This is caused by improper control logic of the ALH. To eliminate this concern, the control software of the ALH has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Reprogram the ALH with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic And Repair Software (MDARS). Refer to MDARS ECU Reprogramming Procedure.
SA-050-26
Service Bulletin/Repair Instructions
DESCRIPTION Some vehicles may continue to display the recall notification "IMPORTANT NOTICE. VIEW VEHICLE STATUS MONITOR FOR DETAILS" on the center display even after the recall has been completed. NOTE: Once the warranty claim for the recall campaign is approved by Mazda Japan, the recall notification will be automatically removed via Connected Services on the following day or later. This condition may occur if the Connected Services subscription was canceled while the recall notification was still active. ACTION TO BE TAKEN If you encounter the situation above, use MDARS to manually remove the center display recall notification. Note: MDARS can only remove the recall notification when MCVV shows no CV contract.
16-010-26
Service Bulletin/Repair Instructions
COMPLIANCE WITH NEW YORK STATE GENERAL BUSINESS LAW §399‑CCCCC (CONNECTED VEHICLE SERVICE; DOMESTIC VIOLENCE VICTIMS) DESCRIPTION This Service Information is issued in accordance with New York State General Business Law §399CCCCC (Connected Vehicle Service; Domestic Violence Victims). This regulation is intended to protect victims of domestic violence by allowing them to request the termination of third-party access (including access by an alleged abuser) to connected vehicle services, such as vehicle location tracking and remote control functions. To support this requirement, this Service Information enables confirmation of whether a vehicle is subject to connected vehicle services by referring to the SUBJECT VIN & PRODUCTION DATE RANGE, and provides guidance on the procedure to terminate such services when a customer requests the removal of third-party access for an applicable vehicle. Effective July 1, 2026, if a customer requests action under this regulation, a CMU/CDC software update must be performed to enable appropriate control of connected vehicle service access. If no request is made by the customer, the CMU/CDC software update is not required. REPAIR PROCEDURE 1. Confirm that the customer has requested deactivation of connected services in accordance with New York State General Business Law related action. 2. Perform the CMU/CDC software update according to the procedures outlined in the appropriate TSB shown in the table below:
SA-042-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SAs listed below. The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out
16-003-26a
Service Bulletin/Repair Instructions
UPDATED SOFTWARE RELEASE FOR CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 16-003/26 01/12/26 DESCRIPTION The release notes outlined below provide an overview of bug fixes, feature improvements, and updates included in the latest software release. The latest version of software contains all the updates of the previous versions. NOTE: If current version is not 7230C1A-NA07_***** or 7230C2A-NA07_*****, this TSB is not applicable. Version 7230C1A-NA07_10036 enables termination of connected services at customer request: Termination of Connected Services by customers at their initiative has been enabled. Accordingly, the following items have been updated. Add a "Data Communication Information" item under Settings > System Settings>Online Connectivity. ○ Updated the text displayed on the confirmation screen for disabling Connected Services. REPAIR PROCEDURE 1. Verify the customer concern. 2. Update MAZDA CONNECT with software version 7230C1A-NA07_10032 / 7230C2A-NA07_10032 or later with a USB memory stick using the 7TH GEN MAZDA CONNECT Update Instructions.
SA-041-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
09-020-26
Service Bulletin/Repair Instructions
DESCRIPTION Some vehicles may exhibit scratches (1) on the rear of the seat back bar garnish (2) from contact with the convertible top (3). Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles. REPAIR PROCEDURE 6. Install the seat back crossmember assembly from the vehicle according to the instructions on MGSS online or the Workshop Manual (section 09-10 SEAT BACK CROSSMEMBER ASSEMBLY REMOVAL/INSTALLATION). 7. Reinstall the rear seat back bar garnish while twisting the garnish so that the garnish can be kept closer to the seat back bar and away from the convertible top (for both left and right sides).
SA-027-26a
Service Bulletin/Repair Instructions
This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-027/26 04/16/26 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. REPAIR PROCEDURE 1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda DCA-8000 Instruction Manual for more information.
SA-0-38/26
Service Bulletin/Repair Instructions
DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status
SA-039-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA listed below. The changes are noted in Red text. SA-012/25 10/06/25, 08/21/25, 05/15/25 and 02/27/25 DESCRIPTION Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE NOTE: Before proceeding: Document the vehicle's current MAZDA CONNECT CMU software version. • 2019-2022 Models - Go to TSB 16-003/23 and confirm the CMU Serial Number is not within the affected range. • Document customer device Brand/Model/Model Number/software version on the repair order. • Confirm that the Connectivity Master Unit (CMU) is updated to the latest software version. Go to MGSS -> Infotainment -> MAZDA CONNECT Updates ○ • If possible, complete the Microsoft Forms Questionnaire. Go to MGSS -> Infotainment -> MAZDA CONNECT Questionnaire.
SA-040-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-009/25 08/22/25 and 02/18/25 DESCRIPTION Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs. Index System Outline • MYMAZDA App Connected Vehicle (CV) Error Codes • Vehicle Confirmation Instructions • Troubleshooting Instructions • Resources
SA-033-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued SA(s) listed below. The changes are noted below in Red. SA-029/25 10/16/25 and 06/02/25 DESCRIPTION This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure. REPAIR PROCEDURE HIGH VOLTAGE BATTERY MAINTENANCE Verify the State-of-charge (SOC) in the instrument cluster. MX-30 EV: If the SOC is lower than 26%, charge it to 50% (either by normal charging or quick charging). CX-90/CX-70 PHEV: If the SOC is lower than 1%, charge it to 10% (either by normal charging, quick charging or engine running).
SA-034-26
Service Bulletin/Repair Instructions
This service alert supersedes the previously issued service alert listed below. The changes are noted in Red text. SA-047/25 10/07/25 DESCRIPTION When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated. CAUTION: DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another vehicle will disable Connected Services on both vehicles. • If TCU activation is not performed, connected vehicle functions will not operate. This will have a negative impact on the customer because they will need to return to the dealer for repairs. • If the Telematics Control Unit (TCU) replacement is necessary, check "Vehicle Communication Line Status Reference" status detail first. The TCU can only be replaced under the following "Status Detail" conditions: Open Completed (OK) ○ Closed Completed (OK) ○ ○ If the TCU is replaced under the following "Status Detail" conditions, the customer may not be able to enroll into the replacement TCU. Processing (NG) ○ Request Failed (NG) ○ Open Failed (NG) ○ Flag Setting Failed TCU Activation 1. Install the new TCU.
SA-031-26
Service Bulletin/Repair Instructions
DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
SA-029-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
SA-026-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
SA-027-26
Service Bulletin/Repair Instructions
This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts.
SA-014-26
Service Bulletin/Repair Instructions
This Service Alert supersedes the previously issued SA(s) and TSB(s) listed below: The changes are noted in Red. SA-035/24 05/31/24 DESCRIPTION There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not. A mechanical seal (A) is used for the water pump. This mechanical seal can seal coolant (B) by sliding a mating ring (C) against a seal ring (D). When the sliding surface temperature of the mechanical seal is more than 248 °F (120 °C) while driving, a small amount of steam (E) is leaked and bleeds through the bleeding hole (F). After drying, the steam leaves a green coolant deposit near the water pump bleed hole (F). This is a normal condition and does not require water pump replacement. The water pump should only be replaced if there is an accumulation of crystallized coolant near the bleed hole. When you encounter a water pump with coolant seepage marks, decide to replace it or not based on the following criteria using sample photos. NOTE: During the initial period of use*, the sliding surfaces of the seals may not yet be fully settled, which can temporarily increase the amount of leakage. Continued use will allow the surfaces to settle, reducing the leakage. Replacing parts that are already settled with new ones will increase the leakage again until the new parts become conditioned. Therefore, replacement should be avoided in this initial period of use. *As a guideline, this applies to vehicles with less than 1,860 miles (3000 km) of mileage.
09-011-26
Service Bulletin/Repair Instructions
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-019/25 04/15/25 Some vehicles equipped with the Adaptive Front lighting System (AFS) may exhibit the exterior light warning light/exterior light warning indication on while driving or when the ignition is turned on and DTC B10A3:86 (Error signal received from swivel actuator (LH)) stored in memory. NOTE: The combination light with AFS can be distinguished if it is equipped with the parking light/daytime running light (DRL) that illuminates while the ignition is turned on. This may be caused by the AFS Control Module detecting a false headlight malfunction. This concern will likely occur when the light returns to the center position after swiveling. To eliminate this concern, the control software of the AFS control module has been further modified.
09-007-26
Service Bulletin/Repair Instructions
Some vehicles may exhibit the power window(s) not working properly (window does not move or has fallen into the door) and/or making an abnormal noise while operating the power window switch. This may be caused by the cable of the power window motor being damaged from water entry through area (1) of the front beltline molding. Convertible Top: To eliminate this concern, the shape of the door glass has been modified during mass production to prevent water entry to the power window regulator. Retractable Hardtop: No mass production change is scheduled.
SA-005-26
Service Bulletin/Repair Instructions
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit codes. • Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. • For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.
09-005-26
Service Bulletin/Repair Instructions
If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. In most cases, if the left-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" can be completed without any problem (See CAUTION below for more details). Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails “BSM OFF" indicator ON Center Display warning message BSM failsafe (No operation) DTC U3000:54 stored in memory DTC U1A4B:54 stored in memory (CX-3, MX-5 only) NOTE: Since a new BSM control module does not retain the vehicle specification information, it is necessary to acquire and store the vehicle specification information transmitted via CAN communication from the combination meter through automatic configuration after replacement.
16-003-26
Service Bulletin/Repair Instructions
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7230C1A-NA07_10032 or 7230C2A-NA07_10032). NOTE: If current version is not 7230C1A-NA07_***** or 7230C2A-NA07_*****, this TSB is not applicable. (Ver. 7230C1A-NA07_10032 & 7230C2A-NA07_10032) fixes these software errors (bugs): Improving Wi-Fi security and reliability • (Ver. 7230C1A-NA07_10028 & 7230C2A-NA07_10028) fixes these software errors (bugs): The infotainment screen may turn black when SIRIUSXM® Satellite Radio is selected. However, the camera images on the center display are not affected, and the back camera is usable. • The system may freeze on the disclaimer screen when the engine is started normally after using the remote engine starter. However, the camera images on the center display are not affected, and the back camera is usable. • Only Bluetooth® connection is established when attempting to connect Android Auto™. • Air conditioning settings cannot be controlled via Alexa without a CV contract. • (Ver. 7230C1A-NA07_10022 & 7230C2A-NA07_10022) fixes these software errors (bugs): Exit information may not be displayed while using navigation. • Although the Navigation SD card is removed, a navigation guidance may be displayed in Active Driving Display and/or the center display. • A navigation command by voice recognition may display Mazda Connect incorrectly. • Pressing the commander may sometimes not display the menu after deleting multiple destinations. • The Wi-Fi client menu is unavailable when the in-vehicle communication unit has no signal. • The smartphone may not be charged when a smartphone is connected to a USB port while connected to Apple CarPlay wireless connection.
09-001-26
Service Bulletin/Repair Instructions
There are wrinkles on the leather seat cushion and/or seat back surface at PDI, when new vehicle is delivered, or when new upholstery is installed under Warranty repair. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal usage.
SA-002-26
Service Bulletin/Repair Instructions
Some customers may complain that the tire sidewalls are distorted or "damaged". Sidewall waviness/indentations/undulations are common on radial tires and are more noticeable on tires with taller sidewalls. The higher the tire pressure, the more noticeable the effect will be. Be sure to set the tire pressures at the recommended tire pressure on the vehicle tire label. Sidewall indentations are a cosmetic condition that does not affect the performance of the tires.
SA-001-26
Service Bulletin/Repair Instructions
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
SA-017-25d
Service Bulletin/Repair Instructions
Mazda Connect Services - Frequently Asked Questions (FAQ)
SA-061-25
Service Bulletin/Repair Instructions
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
SA-023-25c
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop • Door Lock / Unlock • Lights ON / OFF • Climate Control • 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Page
07-004-25a
Service Bulletin/Repair Instructions
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.
SA-056-25
Service Bulletin/Repair Instructions
When inspected, the differential or PTO oil is dark or black. This is considered normal and NO repair should be performed. During production, differential ring and pinion gears receive a manganese phosphate coating (commonly referred to as black oxide). This coating forms a porous, oil-retentive surface that improves boundary lubrication and reduces adhesive wear during initial contact cycles. Designed as a sacrificial layer, it is gradually removed under load throughout the break-in process. As a result, after the first few hundred miles, or at the initial gear oil service interval, the lubricant may appear darkened by the worn-off coating. It will contain trace ferrous particles from the normal run-in of the gear teeth and bearing surfaces. This condition is expected and does not, by itself, indicate an issue with the differential or PTO gears.
SA-055-25
Service Bulletin/Repair Instructions
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.
SA-020-25a
Service Bulletin/Repair Instructions
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
SA-051-25
Service Bulletin/Repair Instructions
Noise, Vibration, and Harshness (NVH) Diagnostic Guidelines Diagnostic Guidelines When diagnosing NVH concerns, it is essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.
SA-052-25
Service Bulletin/Repair Instructions
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.
SA-007-25b
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery.
SA-029-25a
Service Bulletin/Repair Instructions
This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
SA-048-25
Service Bulletin/Repair Instructions
To improved customer experience, an operational modification has been made to unlock the trunk lid after Dynamic Stability Control (DSC) replacement. Be sure to explain the following unlock operational modification to affected customers. Trunk Lid Unlocking Operational Modification: After the engine is turned off and the vehicle remains inactive for more than 5 minutes (sleep mode), it was necessary to operate the electric trunk lid opener switch twice to unlock the trunk lid. • After replacing the Dynamic Stability Control (DSC) with a newly modified part, the trunk lid is unlocked with a single operation, as described in the owner's manual.
SA-047-25
Service Bulletin/Repair Instructions
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
SA-012-25c
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-044-25
Service Bulletin/Repair Instructions
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
SA-042-25
Service Bulletin/Repair Instructions
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.
SA-043-25
Service Bulletin/Repair Instructions
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.
SA-017-25c
Service Bulletin/Repair Instructions
Mazda Connected Services - Frequently Asked Questions
SA-009-25a
Service Bulletin/Repair Instructions
Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.
SA-023-25b
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
SA-039/25
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.
SA-012-25b
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-038-25
Service Bulletin/Repair Instructions
When replacing the MAZDA CONNECT remote tuner (RT) with a replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.
08-002-25
Service Bulletin/Repair Instructions
Some customers may complain that the front passenger seat belt warning light flashes and the seat belt warning beep is activated, even though there is no occupant in the front passenger seat. When a passenger seat occupant sits with a load on the front side for a long time with the seat warmer on, the occupancy sensor becomes dented and sensitive. As a result, the sensor determines that there is an occupant in the front passenger seat even though the seat is empty.
SA-035-25
Service Bulletin/Repair Instructions
Some vehicles may show “TSR system performance is reduced. Navigation Data Unavailable" or "Check Navigation SD Card" in the meter while driving.
SA-034-25
Service Bulletin/Repair Instructions
Some vehicles equipped with the Adaptive Front lighting System (AFS) may exhibit the exterior light warning light/exterior light warning indication on while driving or when the ignition is turned on and DTC B10A3:86 (Error signal received from swivel actuator (LH)) is stored in memory.
09-029-25
Service Bulletin/Repair Instructions
Some customers may notice an abnormal noise (i.e. whine, groan, rattle or squeak) coming from the front combination lights when turning them on, or a few minutes after turning them off. The noise may be due to contamination by foreign matter during the manufacturing process and the fan motor bearing may become worn out during use. To eliminate this concern, the fan motor has been modified. NOTE: It is normal for some noise to occur within the first few seconds after starting the engine, when the front combination lights perform a self check (sweep).
SA-017-25b
Service Bulletin/Repair Instructions
Mazda Connected Services - Frequently Asked Questions (FAQ)
SA-023-25a
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
09-027-25
Service Bulletin/Repair Instructions
Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window.
SA-032-25
Service Bulletin/Repair Instructions
Some customers may complain about a noisy HVAC blower motor or odor after a cabin air filter replacement. Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.
SA-031-25
Service Bulletin/Repair Instructions
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
SA-007-25a
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result
SA-029-25
Service Bulletin/Repair Instructions
This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
SA-028-25
Service Bulletin/Repair Instructions
Some vehicles may have recall notifications remain on the center display even after a recall is performed. NOTE: When the warranty claim for the recall campaign is accepted at Mazda Japan, the recall notification will be automatically deleted via the Connected Service on the next day or later. This situation occurs if the Connected Service subscription has been cancelled while the recall notifications remain.
SA-012-25a
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-017-25a
Service Bulletin/Repair Instructions
Frequently Asked Questions (FAQ) for Mazda Connected Services.
SA-023-25
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
07-004-25
Service Bulletin/Repair Instructions
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
SA-020-25
Service Bulletin/Repair Instructions
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
SA-017-25
Service Bulletin/Repair Instructions
Frequently Asked Questions (FAQ)
SA-012-25
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-009-25
Service Bulletin/Repair Instructions
Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.
SA-004-25a
Service Bulletin/Repair Instructions
Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricted, thereby extending the transmitter battery life and the following will occur: The engine will not start unless the key transmitter is held over the Start Stop button. • Outside door handle lock/unlock touch sensor is inoperative. • Key transmitter indicator lights are inoperative. • The following DTC's may be stored: DTC B13D3:94 (Communication error with remote transmitter) ○ DTC P1260:00 (Immobilizer system problem).
SA-007-25
Service Bulletin/Repair Instructions
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
SA-005-25
Service Bulletin/Repair Instructions
Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.
SA-004-25
Service Bulletin/Repair Instructions
Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricted, thereby extending the transmitter battery life. NOTE: Some customers may complain about an engine no start. This may be caused by the customer inadvertently putting the key transmitter in Power Saving Function.
SA-009-24e
Service Bulletin/Repair Instructions
Frequently Asked Questions (FAQ)
SA-017-24c
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
SA-081-24
Service Bulletin/Repair Instructions
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
SA-070-24a
Service Bulletin/Repair Instructions
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
09-046-24
Service Bulletin/Repair Instructions
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
SA-031-24a
Service Bulletin/Repair Instructions
This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
SA-016-24c
Service Bulletin/Repair Instructions
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
09-001-24g
Service Bulletin/Repair Instructions
Some customers may experience a “Telematics Malfunction” message in the instrument cluster with DTC U3000:00-TCU (Emergency call unit/telematics communication unit internal malfunction) or U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
SA-009-24d
Service Bulletin/Repair Instructions
Mazda Connect Services - Frequently Asked Questions (FAQ)
SA-064-24
Service Bulletin/Repair Instructions
Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.
SA-015-24d
Service Bulletin/Repair Instructions
Alexa Built-In Frequently Asked Questions (FAQ)
SA-070-24
Service Bulletin/Repair Instructions
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
SA-068-24
Service Bulletin/Repair Instructions
Some customers may complain about scratches on the instrument cluster lens.
SA-006-24c
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-009-24c
Service Bulletin/Repair Instructions
Mazda Connect Services - Frequently Asked Questions (FAQ)
SA-017-24b
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
SA-062-24
Service Bulletin/Repair Instructions
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
SA-016-24b
Service Bulletin/Repair Instructions
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
SA-057-24
Service Bulletin/Repair Instructions
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
SA-058-24
Service Bulletin/Repair Instructions
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
SA-060-24
Service Bulletin/Repair Instructions
Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.
SA-056-24
Service Bulletin/Repair Instructions
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
SA-053-24
Service Bulletin/Repair Instructions
Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
09-038-24
Service Bulletin/Repair Instructions
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
SA-052-24
Service Bulletin/Repair Instructions
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
SA-006-24b
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-011-24b
Service Bulletin/Repair Instructions
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
09-016-24a
Service Bulletin/Repair Instructions
Some vehicles may exhibit scratches (1) on the rear of the seat back bar garnish (2) from contact with the convertible top (3). Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles.
09-036-24
Service Bulletin/Repair Instructions
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. • Wrinkles may not be completely removed after the repair is completed. • Leather is a natural material and may develop some wrinkles due to aging and wear during normal useage.
SA-037-24
Other
The following DTCs are missing from the 2024 MX-5 WSM, but you can refer to the 2023 MX-5 for these DTCs to troubleshoot a 2024 model. B00A0:09 B00A0:28 B00A0:4A B00A0:54 B00A0:55 B00A0:81 B00A0:87
SA-009-24b
Other
Mazda Connected Services - Frequently Asked Questions (FAQ)
09-034-24
Service Bulletin/Repair Instructions
Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by: CASE A: The J-hook binding holding the inner cloth coming loose because the convertible top is opened/closed a lot or from high ambient temperatures. CASE B: After the previous improvement carried out at the supplier since January 19, 2016, some J-hooks have still been found coming loose to bind and hold the inner cloth during the assembly process. To correct the problem: CASE A: Two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating. CASE B: An improved inspection process has been started at the supplier to check the appearance of the inner cloth after installation of the clip.
SA-011-24a
Other
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
SA-016-24a
Other
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
SA-022-24a
Other
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
SA-035-24
Other
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
SA-031-24
Other
This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
SA-032-24
Other
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
SA-015-24c
Other
Alexa Built-In Frequently Asked Questions (FAQ)
SA-015-24b
Other
Alexa Built-In Frequently Asked Questions (FAQ)
SA-015-24a
Service Bulletin/Repair Instructions
Alexa Built-In Frequently Asked Questions (FAQ)
SA-017-24a
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
SA-022-24
Service Bulletin/Repair Instructions
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
09-016-24
Service Bulletin/Repair Instructions
Some vehicles may exhibit scratches (1) on the rear of the seat back bar garnish (2) from contact with the convertible top (3).
SA-017-24
Service Bulletin/Repair Instructions
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF, Climate control
SA-016-24
Service Bulletin/Repair Instructions
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
PF-24-03
Service Bulletin/Repair Instructions
Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
SA-015-24
Service Bulletin/Repair Instructions
Alexa Built-In Frequently Asked Questions (FAQ)
SA-009-24a
Service Bulletin/Repair Instructions
Frequently Asked Questions (FAQ): General Questions, Reception Level Inspection, Setup and Getting Started, Dealer Processes, Registration / Enrollment, TCU Activation, WI-FI General Information, Conditions for Remote Engine Start Will Not Function, WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF, WI-FI Trial Period, Deactivation Mode, Interacting With The App, Educational Videos, Service Issues, Resources, Troubleshooting Page.
SA-013-24
Service Bulletin/Repair Instructions
Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).
SA-014-24
Service Bulletin/Repair Instructions
Some customers may complain that the tire sidewalls are distorted or "damaged". Sidewall waviness/indentations/undulations are common on radial tires and are more noticeable on tires with taller sidewalls. The higher the tire pressure, the more noticeable the effect will be. Be sure to set the tire pressures at the recommended tire pressure on the vehicle tire label. Sidewall indentations are a cosmetic condition that does not affect the performance of the tires.
SA-011-24
Service Bulletin/Repair Instructions
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
SA-009-24
Service Bulletin/Repair Instructions
Frequently Asked Questions (FAQ): General Questions, Reception Level Inspection, Setup and Getting Started, Dealer Processes, Registration / Enrollment, TCU Activation, WI-FI General Information, Conditions for Remote Engine Start Will Not Function, WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF, WI-FI Trial Period, Deactivation Mode, Interacting With The App, Educational Videos, Service Issues, Resources, Troubleshooting Page.
SA-006-24
Service Bulletin/Repair Instructions
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
SA-081-23
Service Bulletin/Repair Instructions
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.