Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
01-006-21-3779a
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
09-025-21-3824
This service bulletin provides information regarding the proper use of the driverâÂÂs floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.
01-005-21-3778
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
01-006-21-3779
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer
09-003-20-3671
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealerâÂÂs responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. ï· Mazda vehicles are manufactured with tamper-proof speedometers. ï· When a speedometer is replaced, the new speedometer will read zero (0) miles. ï· This procedure is extremely important to accurately represent actual vehicle mileage. ï· Prior to speedometer removal, complete the information required on the âÂÂSpeedometer Replacement LabelâÂÂ. Labels can only be ordered through Mazda eStore. ï· In an effort to achieve a higher level of Customer Experience and retain the value of MazdaâÂÂs vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOâÂÂs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
09-009-19-3566
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
01-004-19-3558
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
09-002-19-3554
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.
01-001-19-3551
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
01-002-19-3552
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps):CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery's Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda GR8-1291, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries.
00-001-18-3446a
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
00-003-18-3480a
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.
09-014-18-3443a
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
09-034-18-3430a
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
01-016-18-3522
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
09-034-18-3430
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
00-003-18-3480
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.
01-008-18-3451
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
01-009-18-3452
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
09-019-18-3450
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.
00-001-18-3446
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
09-014-18-3443
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
09-035-17-3080
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
SA287
DUE TO DIFFERENCES IN THE 1995-1998 PROTÉGÉ IGNITION SWITCH DESIGN, THE REPAIR PROCEDURE AND WARRANTY INFORMATION FOR RECALL 8715J HAS BEEN UPDATED.
0901216
Paint damage Mazda pocket paint guide
0900716
Speedometer replacement procedure
0100516
Battery test procedure requirements using the GR81291
09-034-14-2956
IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
00-002-14-2936
MAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.
09-027-14-2935
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
00-001-13-2748A
MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.
09-005-13-2781
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTEN-TIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE.FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION.INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED.FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
SB-09-005-13
MAZDA: ON SOME VEHICLES, TO AVOID POTENTIAL INTERFERENCE OF FOOT PLACED ON PEDALS, INFORMATION IS PROVIDED REGARDING PROPER USE, AND PLACEMENT, OF DRIVER'S FLOOR MAT. VARIOUS MODELS AND MODEL YEARS. *PE
00-001-13-2748
MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.
00-004-12-2741
MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.
00-004/12
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
00307
AVAILABILITY OF NON-REQUIRED TOOLS. *KB
0800306
NON GENUINE ACCESSORIES AFFECT AIR BAG OPERATION. *KB
00204
EVAPORATIVE EMMISSIONS AND RECIVER ADAPTERS. *EH
0102504
BATTERY TEST PROCEDURE REQUIREMENTS. *TT
0902604
SPEEDOMETER REPLACEMENT PROCEDURE. *TT
01100R
ON SOME VEHICLES WITHIN CERTAIN VINS, THE DOOR KEY CYLINDER FLAP MAY BREAK ALLOWING A PIECE(S) OF THE FLAP TO ENTER THE CYLINDER THEREBY MAKING IT DIFFICULT TO INSERT THE KEY AND CAUSING KEY ROTATION TO STICK. *TT
00700
CIGARETTE LIGHTER DOES NOT WORK OR STAY IN POSITION. *TT
00200R
THIS BULLETIN EXPLAINS CAMBER ADJUSTMENT PROCEDURES. *TT
00100
SOME VEHICLES MAY EXHIBIT THE AIR CONDITIONING (A/C) SYSTEM INOPERATIVE WITH THE MALFUNCTION INDICATOR LAMP (MIL) ON. *TT
01399
CONCERNS WITH DOOR KEY WHICH IS DIFFICULT TO INSERT AND / OR ROTATE. *TT
01299
SUBJECT REGARDING PAINT DAMAGE - IRON PARTICLES / INDUSTRIAL FALLOUT / ACID RAIN. *TT
00299
EXPERIENCING POPPING NOISE FROM FRONT BRAKE CALIPER DURING SLOW SPEED BRAKING. *TT
00198
SOME VEHICLES MAY EXPERIENCE NOISE FROM DRIVE SHAFT. *YC
01098
SOME VEHICLES MAY EXHIBIT ERRATIC SHIFTING, O/D OFF INDICATOR LIGHT FLASHING WITH MALFUNCTION INDICATOR LAMP ON AS A RESULT OF THE VALVE BODY HARNESS (TRANSAXLE FLUID TEMPERATURE SENSOR CIRCUIT) BEING PINCHED BY A METAL CLIP WHICH IS ATTACHED TO THE TRANSMISSION CONTROL VALVE BODY, CAUSING A SHORT / OPEN CIRCUIT. *TT
00998
AUTOMATIC TRANSAXLE SELECTOR LEVER IS DIFFICULT TO OPERATE. *YC
02098
EXHIBITING A RUBBING NOISE HEARD FROM THE FRONT CONSOLE WHEN DRIVING. *YC
00298
EXPERIENCING A THUMPING NOISE FROM REAR SUSPENSION TOWER. *YC
00898
CONCERNS WITH THE AUDIO SOUND CUTS OUT WHEN BLOWER MOTOR OPERATES. *YC
01498
CONCERNS WITH WATER LEAKAGE ONTO FRONT FLOOR MAT. *YC
01298
CONCERNS WITH MANUAL CONTROL DOOR MIRROR NOT ADJUSTABLE. *YC
00598
SUBJECT REGARDING BRAKE WARNING LIGHT ON CONSTANTLY. *YC
00698
EXHIBITING NOISE FROM THE HOOD RELEASE CABLE. *YC
97102302097
PRE-PAINTING PREPARATIONS FOR FRONT AND REAR BUMPERS. *YC
97083000997
CONDITION WITH INTERIOR LIGHT DOES NOT ILLUMINATE. *YC
970716007/97
CUSTOMERS COMPLAINING OF MIL LAMP ILLUMINATION. *YC
970716015/97
CONCERNS OF RATTLING OR BUZZING NOISES IN THE FRONT OF VEHICLES. *YC
009/97T
INTERIOR LIGHT DOES NOT ILLUMINATE. *TW
012/97T
TACH NEEDLE STUCK ON WRONG SIDE OF STOPPER PIN. *TW
007/97U
A/C REFRIGERANT CHARGING. *TW
008/97
USE OF A/C TRACER DYE. *TW
007/97T
PARTS REPLACEMENT AFTER AIRBAG DEPLOYMENT. *TW
001/97G
MAINTENANCE FREE BATTERY - DIAGNOSTIC AND CHARGING PROCEDURE. *TW
006/97/U
A/C MALFUNCTION DUE TO POWER STEERING PUMP PRESSURE SWITCH CORROSION. *TW
002/97S
REAR EDGE OF ROOF MOLDING LIFTS. *TW
003/97U
A/C SWITCH MODIFICATION. *TW
003/97G
WIPER MOTOR INOPERATIVE - CIRCUIT BREAKER ACTIVATION. *TW
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.