Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ZR-IB-018-C
McNeilus Truck and Manufacturing, Inc. offers these instructions for the Zero Radius (ZR) 3.0 speed limiter software update. This document covers some configurations. Revision C updates one step on a Mack diesel version chassis.
MISC_IB_085-A
McNeilus Truck and Manufacturing provides these instructions for the installation of new bushings for the service cleanout door for all Side Loader refuse vehicles. The new bushings can help provide a tighter seal on the door.
ZR-IB-012-E
This bulletin instructs how to replace the Zero Radius™ (ZR) grabber carriage motor bolts with new bolts if the existing motor bolts are loosening. Revision E replaces two parts with updated parts.
MISC-IB-085
McNeilus Truck and Manufacturing provides these instructions for the installation of new bushings for the service cleanout door for all Side Loader refuse vehicles. The new bushings can help provide a tighter seal on the door.
ZR-IB-021
The McNeilus Body Control software on Zero Radius (ZR) side loaders has been updated to support the Neutral at Stop (NAS) enhancement offered by some chassis OEMs. The McNeilus Body Control software update will communicate to the chassis OEM that the McNeilus body is in Collection Mode.
MISC-IB-084-A
McNeilus Truck and Manufacturing requires an inspection and replacement, if needed, to ensure the Bob Tail® Huck® bolts are fully swaged with correct thread exposure on the rear pivot cross member body mounts. Revision A updates the replacement bolt length to 90mm
MISC-IB-084
McNeilus Truck and Manufacturing requires an inspection and replacement, if needed, to ensure the Bob Tail® Huck® bolts are fully swaged with correct thread exposure on the rear pivot cross member body mounts.
ZR-IB-018_A
Instructions for the ZR speed limiter software update.
ZR-TSIB-012-D
This bulletin instructs to how remove the Zero Radius™ (ZR) grabber carriage motor bolts/studs and replace with new bolts if the motor bolts are loosening. Revision D adds procedure steps to section 3.2 and removes an outdated image.
ZR-TSIB-012-C
This bulletin instructs to how remove the Zero Radius™ (ZR) grabber carriage motor bolts/studs and replace with new bolts if the motor bolts are loosening. Revision C replaces studs with bolts
ZR-IB-016
It has been determined that certain McNeilus Zero Radius side loader refuse vehicles may have a hydraulic pressure spike that may cause premature failure to the fan cooler. The fan cooler may be permanently bypassed by following the instructions in this informational bulletin to bypass the fan cooler with a hydraulic hose allowing the refuse body functions to remain functional.
MISC-TSIB-081
According to an amended ruling in the visual inspection labeling requirement in Federal Motor Vehicle Safety Standard (FMVSS) No. 304, the periodic inspection interval for compressed natural gas (CNG) fuel containers has been modified to âat least every 12 months.â McNeilus Truck and Manufacturing will support this change by updating safety decals and installing these new decals when a vehicle is inspected by McNeilus CNG technicians, and by answering questions regarding this periodic inspection interval update and how McNeilus will support it.
ZR-TSIB-015
McNeilus Truck and Manufacturing offers these instructions for the installation of a hydraulic reservoir breather upgrade kit to reduce oil leakage in in-body hydraulic reservoirs and frame mounted hydraulic reservoirs on Zero Radius (ZR) Side Loader refuse vehicles.
MISC-TSIB-079
McNeilus Truck and Manufacturing provides these instructions for installing a hydraulic reservoir cork gasket. The installation of this gasket will repair leaks coming from the gasket between the in-tank filter and the reservoir.
WM-TSIB-022
McNeilus Truck and Manufacturing offers these instructions for the installation (retrofit installation) of a streetside panel/door on the tailgate in an effort to reduce trash buildup behind the CNG cover. This is for Zero Radius trucks with roof mounted compressed national gas (CNG) units.
MISC-TSIB-075-A
The following information describes how to purge air and release stored hydraulic energy from a hydraulic system. All manual override features are intended for emergency use, not for continuous-duty operation.
ZR-TSIB-012-B
This bulletin instructs to how remove the Zero Radius⢠(ZR) grabber carriage motor bolts and replace with studs if the motor bolts are loosening.
MISC-TSIB-078
McNeilus Truck and Manufacturing offers these instructions for ejector cylinder bypass testing.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.