Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
CL - Tank Leak Detection
Warranty Program/Extension
Dear Mercedes-Benz Owner: In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. • If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. • This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.
LI82.62-P-078631
Service Bulletin/Repair Instructions
Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!
LI35.30-P-058566
Service Bulletin/Repair Instructions
Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).
LI82.30-P-059239
Service Bulletin/Repair Instructions
Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).
LI82.10-P-078301
Service Bulletin/Repair Instructions
Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304
CL - 05012025
Other
In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage detection (“DMTL”) on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership.
LI82.85-P-079088
Service Bulletin/Repair Instructions
Complaint The following most common complaints may be observed: • Brief connectivity interruptions when using Apple CarPlay over Wi-Fi • Audio cuts out • Device not recognized • No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicle’s head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference External Sources: • Passing under toll bridges, driving near airports, or areas with heavy electronic interference (e.g., as described in LI82.85-P-076157) can cause connection drops. Cellular Networks: • Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: • Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Issues Head Unit Software/Hardware: • Outdated firmware, bugs, or hardware faults in the vehicle’s head unit can prevent a stable connection. iPhone Software/Hardware: • Similar issues in the iPhone, including buggy iOS updates or hardware problems, may affect performance. Reset or Reboot: • Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings Wired Connections: • Faulty Cable: A damaged or poor-quality USB cable can cause intermittent or total loss of connection. • USB Port Issues: Dust, debris, or physical damage in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: • Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: • Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. • Vehicle’s Electrical System: Unstable power delivery from the car’s battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration Phone Settings: • Incorrect or conflicting settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. • Third-Party Apps/Profiles: • Installed apps or configuration profiles may conflict with CarPlay’s operation. • Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: • Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: • Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors Heat & Overheating: • If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: • Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy Guided Diagnostic Path for Apple CarPlay Connection Issues Please follow the steps below to systematically diagnose and resolve CarPlay concerns: Update Devices: • Ensure the iPhone is updated to the latest available iOS version. • Ensure the vehicle’s head unit is updated to the latest software version available. Isolate the Issue: • Check whether the symptom persists with another iPhone running the latest iOS version. • Test both wireless and wired CarPlay connections: • Does the issue only occur with wireless CarPlay?
LI33.30-P-056665
Service Bulletin/Repair Instructions
Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts
LI82.10-P-078896
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.
LI82.70-P-077433
Service Bulletin/Repair Instructions
Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
LI82.35-P-078467
Service Bulletin/Repair Instructions
Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
LI01.20-P-078446
Service Bulletin/Repair Instructions
Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. • The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
LI82.10-P-078307
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
LI82.10-P-078069
Service Bulletin/Repair Instructions
Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
LI91.18-P-077075
Service Bulletin/Repair Instructions
Crease formation on genuine leather seat covers in vehicles with low mileage ⢠Objects left on the seats for extended periods of time (pressure marks). ⢠Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). ⢠Light initial creases due to vehicle handling. ⢠Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
LI82.85-P-076800
Service Bulletin/Repair Instructions
The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
NCU-HU SW Update
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âMBAGâ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customerâs vehicle. The OTA may be validated as successful on the customerâs Mercedes Me connect app under âOver-the-Air Vehicle Updatesâ as âUpdate for the communication moduleâ. If the OTA is successful it will show a green âinstalledâ and date of installation in the Over-the-Air update section.
LI09.00-P-074093
Service Bulletin/Repair Instructions
MY15+ M278 and M157 Equipped Vehicles with Fault Code "P023400 â Boost Pressure is Too High"
LI8270P073025
Service Bulletin/Repair Instructions
Insufficient charging or no wireless charging with iPhone 12.
LI00.20-P-070791
Service Bulletin/Repair Instructions
Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
LI82.85-P-071529
Service Bulletin/Repair Instructions
MBUX multimedia system: "Favorites" and "Recent destinations" not available
P-SC-2020020001
Service Bulletin/Repair Instructions
Information Label on Tire Sealant
LI72 40-P-069934
Service Bulletin/Repair Instructions
Outside mirror folding out/in nonfunctional
LI32 25-P-069969
Service Bulletin/Repair Instructions
Noise from front axle suspension
LI83 30-P-068662
Service Bulletin/Repair Instructions
Air conditioning system heating instead of cooling
LI82 85-P-069670
Service Bulletin/Repair Instructions
MBUX multimedia system: Incorrect vehicle image in home screen menu bar
LI82-85-P-069467
Service Bulletin/Repair Instructions
MBUX multimedia system: "Freeway" pop-up display cannot be deactivated
LI82-20-P-069458
Service Bulletin/Repair Instructions
Ambient lighting remains white
LI54-18-P-069309
Service Bulletin/Repair Instructions
Fault message "SRS - Service Required" displayed in instrument cluster and SRS lamp active
LI80-57-P-069371
Service Bulletin/Repair Instructions
After blocking a key track, the existing key may no longer function
LI82-85-P-069381
Service Bulletin/Repair Instructions
MBUX multimedia system: The central display turns dark, interference noise from speakers
LI80-57-P-069369
Service Bulletin/Repair Instructions
Software update for electronic ignition lock may not be possible
LI82-85-P-069370
Service Bulletin/Repair Instructions
MBUX multimedia system: Fault code B1F9997 is shown as stored
LI5418P069309
Service Bulletin/Repair Instructions
Message "SRS - Service Required" displayed in instrument cluster and SRS lamp active
LI8270P069308
Service Bulletin/Repair Instructions
Inductive charging: Mobile phone is sometimes not recognized during charging process
LI5410P066942
Service Bulletin/Repair Instructions
177 Battery discharged; vehicle does not start
LI82 85-P-068721
Service Bulletin/Repair Instructions
SOS nonfunctional message in instrument cluster and/or head unit
LI82 85-P-068670
Service Bulletin/Repair Instructions
MBUX multimedia system: Empty popup after sending a POI via Send2Car
LI54 10-P-068419
Service Bulletin/Repair Instructions
Fault B214B72; B214F11; B214F73 Current and Stored
LI47 10-P-068407
Service Bulletin/Repair Instructions
Course of action when fuel tank on model series 177 is overfilled because of malfunctioning fuel dispenser
LI54 70-P-068094
Service Bulletin/Repair Instructions
Message (yellow) in IC "Active Brake Assist functional scope currently restricted, see Owner's Manual"
LI54 10-P-068338
Service Bulletin/Repair Instructions
Only affects launch model 177!!! FC B11C118 and FC B11C113 active and stored
SWPU0420095035
Service Bulletin/Repair Instructions
Sprinter weekly parts update.
LI82 20-P-067107
Service Bulletin/Repair Instructions
LED light on thermal cup holder in rear passenger compartment of BR 222 flickers
LI82 20-P-067044
Service Bulletin/Repair Instructions
Partial operation of interior ambient lighting
LI54.15-P-057373
Service Bulletin/Repair Instructions
The vehicle cannot be started The vehicle may start by itself shortly after the startup attempt with a delay, as the relay can be late closing. and/or The gear selection is displayed, but no gear is engaged. Gear selection is not possible. and/or Rear window wiper inoperative. and/or Various fault codes concerning disrupted communication paths are stored and/or the corresponding control units are not displayed in the quick test. Affected control units include the transmission control unit, electronic ignition lock, driver SAM, engine control unit, Lane Keeping Assist, Distronic.
LI27.60-P-058317
Service Bulletin/Repair Instructions
Transmission intermittently fails to shift, vehicle jolts in higher gears. The dual clutch transmission (DKG) control unit contains the stored FC 92177 or 92100 - The shift valve of the internal shaft has a malfunction. The commanded position was not reached. In the extended fault freeze frame data it can be seen that this fault was set in 7th gear - see Figure 1 in attachment.