Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
LI82.62-P-078631
Service Bulletin/Repair Instructions
Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!
LI35.30-P-058566
Service Bulletin/Repair Instructions
Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).
LI82.10-P-078301
Service Bulletin/Repair Instructions
Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304
LI82.10-P-078307
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
LI82.10-P-078896
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. **NOTE - As of Sept 2025 the pressure testing tool is not finalized and may require modifications to fit properly. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.
LI33.30-P-056665
Service Bulletin/Repair Instructions
Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts
LI82.70-P-077433
Service Bulletin/Repair Instructions
Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
LI82.35-P-078467
Service Bulletin/Repair Instructions
Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
LI82.10-P-078069
Service Bulletin/Repair Instructions
Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
LI91.18-P-077075
Service Bulletin/Repair Instructions
Crease formation on genuine leather seat covers in vehicles with low mileage ⢠Objects left on the seats for extended periods of time (pressure marks). ⢠Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). ⢠Light initial creases due to vehicle handling. ⢠Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
EW - Seat Heaters
Warranty Program/Extension
To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core business, Mercedes-Benz USA, LLC (MBUSA) entered into a settlement regarding claims relating to the original equipment seat heaters in model year 2000-2007 M-Class, 2006-2007 R-Class, and 2007 GL-Class vehicles. As part of the settlement, MBUSA offers extended warranty coverage for repairs necessitated by wear and tear of seat heater electrodes in the outer bolster of the front driver's side seat, which in rare circumstances could sear a hole in the seat cover. The warranty extension lasts for a period of up to May 16, 2020 or 180,000 miles, whichever occurs first. Warranty coverage is provided on a sliding-scale based on mileage, as described below. What Is Covered: The warranty extension covers repairs or replacements necessitated by resistance heating of the seat heater electrodes, which may result in a sear hole in the outer bolster of the driver's side seat bottom cover or seat back cover - that is, when a hot spot occurs in the seat heater a hole may develop in the seat cover ("Qualified Repair").
LI8330P0496447
Service Bulletin/Repair Instructions
No cooling output, fault code 9006 stored in air conditioning control unit.
LI82.10-P-064172
Service Bulletin/Repair Instructions
Headlamp lights up sporadically
RecallUpdate
Service Bulletin/Repair Instructions
Recall Campaign announcement for Takata driver airbags.
LI72.20-P-061209
Service Bulletin/Repair Instructions
Noises from rear-end door
LI91.22-P-059988
Service Bulletin/Repair Instructions
2nd seat row Power Easy Entry function impairment of backrest folding
LI91.22-P-059388
Service Bulletin/Repair Instructions
Electric motor for the folding rear backrest of the 3rd seat row is inoperative or makes noises during adjustment
LI91.12-P-059378
Service Bulletin/Repair Instructions
The release loop of the Easy Entry seat in the 2nd seat row is awkward to operate as it is difficult to access
C1A140101
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
GI88.40-P-057430
Service Bulletin/Repair Instructions
Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
LI8270P055572
Service Bulletin/Repair Instructions
Mobile phone cotacts are not transferred completely.
LI27.20-P-055758
Service Bulletin/Repair Instructions
FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
LI82.95-P-056655
Service Bulletin/Repair Instructions
Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
LI82.85-P-055695
Service Bulletin/Repair Instructions
The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
LI47.20-P-054958
Service Bulletin/Repair Instructions
Combination message: "Clean fuel filter" is displayed. The fault code 162500 (water level message - Bosch) or P226997 (water level message - Delphi) or 171600 (filter load - Bosch) is stored in the engine control unit.
LI-47-50
Service Bulletin/Repair Instructions
MERCEDES-BENZ: THE FUEL LEVEL INDICATOR IS WRONG.
LI-68-50
Service Bulletin/Repair Instructions
MERCEDES-BENZ: THE LOAD COMPARTMENT ROLLER BLIND HAS CATCH BOLTS LOOSE OR BROKEN FROM IMPROPER FORCE WHEN USING. *RM
SB-32-25-82
Service Bulletin/Repair Instructions
MERCEDES-BENZ: SHOCK ABSORBER PROCEDURE. *RM
P-049567
Service Bulletin/Repair Instructions
MERCEDES: BATTERY SYMBOL AND SERVICE REQUIRED (IN WHITE). FAULT MESSAGE IS DISPLAYED IF THE CHARGE LEVEL IS TOO LOW OR THE PARK PAWL ADDITIONAL BATTERY IS DEFECTIVE. IN ADDITION FAULT CODE FC 9061 AND/OR FC 9062 IS STORED IN THE FRONT SAM. *PE
LI-58-40
Service Bulletin/Repair Instructions
XENTRY (MERCEDES): ENGINE WARNING LAMP IS CURRENTLY ON OR WAS ON AND A DELAY FAULT OF THE CAMSHAFT ADJUST TO CURRENT OR STORED IN THE ENGINE CONTROL UNIT. MODELS 171, 203, 209, 211, 219, 221, 216, 230, 164, 251, AND 403. NO MODEL YEARS LISTED. *PE
TB-P-047927
Service Bulletin/Repair Instructions
MERCEDES: FOLLOWING FAULT CODES ARE ENTERED IN THE CONTROL UNIT AND DISPLAYED-FC5320 DRAIN VALVE:OPEN CIRCUIT OR INSUFFICIENT VALVE CURRENT IN MODELS SERIES 211, 219; FC5260 DRAIN VALVE OPEN CIRCUIT OR INSUFFICIENT VALVE CURRENT IN MODEL 221; FC5250 DRAIN OPEN CIRCUIT OR INSUFFICIENT VALVE CURRENT IN MODEL SERIES 251, 164. DEFECTIVE CONNECTING CABLES TO DRAIN VALVE AT AIRMATIC COMPRESSOR. THIS RESULTS IN THE SETTING OF THE FAULT CODES. NO MODEL YEARS LISTED. *PE
RB-2009060005
Service Bulletin/Repair Instructions
MERCEDES BENZ SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SOFTWARE CALIBRATION NUMBER (SCN) CODING; ENGINE CONTROL MODULE. THE VEHICLES FUEL TANK LEAK DIAGNOSIS SYSTEM MAY HAVE BEEN INADVERTENTLY DEACTIVATED DURING A VISIT TO THE WORKSHOP. THIS MAY CAUSE THE AFFECTED VEHICLES TO FAIL TO MEET THE STATUTORY REQUIREMENTS FOR INSPECTION AND OR MAINTENANCE (EMISSIONS INSPECTION). *PE
SB-82-30-366E
Service Bulletin/Repair Instructions
MERCEDES BENZ: ADJUSTING WIPER ARMS. IF YOU RECEIVE REPORTS ON CERTAIN VEHICLES OF WIPERS CHATTERING/NOISY, PROCEED AS FOLLOWS: INSPECT WIPER BLADES/INSERTS FOR WEAR AND REPLACE; THOROUGHLY CLEAN WINDSHIELD; VERIFY USE OF CORRECT WASHER FLUID; CHECK WASHER NOZZLE ADJUSTMENT; CHECK WIPER ARM ANGLE ADJUSTMENT; AND RECORD VALUES PER APPLICABLE MODEL; IF REQUIRED, ADJUST WIPER ARM ANGLE. MODELS 164/251. NO MODEL YEARS LISTED. *PE
SB-32-22-78
Service Bulletin/Repair Instructions
MERCEDES: AIR MATIC VISIT WORKSHOP DISPLAYED WITHIN INSTRUMENT CLUSTER. MODELS 164, 211, 219, 221 AND 251. INCLUDED 4MATIC, AMG (COMPRESSOR) AMG, BLUETEC AND WAGON. MODEL YEARS UNKNOWN. *PE UPDATED 9/18/09. *PE
SB-07-16-80D
Service Bulletin/Repair Instructions
MERCEDES BENZ: FUEL LOSS AT PRESSURE REGULATOR VALVE AND/OR POOR ENGINE RUNNING CHARACTERISTICS (SHAKES, KNOCKS, SURGES, CHANGES TO LIP HOME MODE, POOR OUTPUT, POOR FUEL ECONOMY, COMBUSTION NOISE, VEHICLE STALLS). MAY BE CAUSED BY MALFUNCTION AT PRESSURE REGULATOR VALVE (PRV) DUE TO IMPROPER INSTALLATION. *PE
TB-83-10-112B
Service Bulletin/Repair Instructions
MERCEDES: A NONFUNCTIONAL BLOWER MOTOR (BLOWER MOTOR RUNS CONTINUOUSLY) OR WATER DROPS IN FRONT PASSENGER FOOTWELL AFTER ENGINE WASH. CAUSED BY AN INSUFFICIENT SEALING OF AIR/WATER BOX WHEN WATER IS USED WHEN ENGINE COMPARTMENT IS CLEANED NEAR RIGHT SIDE OF FIREWALL.
462046
Service Bulletin/Repair Instructions
PLAY IN THE RACK AND PINION STEERING SYSTEM. MODELS 203, 209, 210, 211, 215, 220, 230. MERCEDES BENZ. *KB UPDATED 5/13/09. *PE
TB-46-10-32
Service Bulletin/Repair Instructions
MERCEDES: GROANING OR DULL, HEAVY CRACKING NOISES FROM STEERING SHAFT AREA. WHEN TURNING STEERING WHEEL OR MOVING OFF OR BRAKING. THIS MAY BE EMANATING FROM THE BEARING AND HOUSING OF UPPER STEERING SHAFT (FIREWALL PIVOT POINT) OR STEERING COUPLING (LOWER STEERING SHAFT). MODELS 164 AND 251. MODEL YEARS UNKNOWN. *PE
TB-46-10-39C
Service Bulletin/Repair Instructions
MERCEDES: CHROME PLATING PEELING ON DECORATIVE CAPS ON THE STEERING WHEEL SPOKES, THIS IS DUE TO LESS THAN OPTIMAL ADHESION BETWEEN CHROME PLATING AND BASE MATERIAL. MODELS 164 AND 251. MODEL YEARS UNKNOWN. *PE
TB-91-12-114A
Service Bulletin/Repair Instructions
MERCEDES: RIGHT SIDE SECOND ROW SEAT FOLD UP MECHANISM NOT WORKING CORRECTLY OR INOPERATIVE; RIGHT SIDE SECOND ROW SEAT RED RELEASE STRAP INOPERATIVE. MODEL YEARS UNKNOWN. *PE
SB-2008080001
Service Bulletin/Repair Instructions
MERCEDES: CHECK AIR SUSPENSION COMPRESSOR AND REPLACE IF NECESSARY. INSUFFICIENT AIR PRESSURE IN THE AIR SUSPENSION SYSTEM MAY RESULT FROM DAMAGE TO THE PRESSURE DISK IN THE AIR SUSPENSION COMPRESSOR. *PE
SB-07-16-08
Service Bulletin/Repair Instructions
MERCEDES BENZ: WORK ON PRESSURE REGULATOR VALVE (AS OF CD13, 1600 BAR SYSTEM). FUEL LOSS AT THE PRESSURE REGULATOR VALVE AND/OR POOR ENGINE RUNNING CHARACTERISTICS (SHAKES, KNOCKS, SURGES, CHANGES TO LIMP HOME MODE, POOR OUTPUT, POOR FUEL ECONOMY, COMBUSTION NOISE). *PE
SB-09-20-29
Service Bulletin/Repair Instructions
MERCEDES BENZ: OIL LEAK AT THE ENGINE AIR INTAKE DUCT. OIL LEAKAGE AT THE AIR INTAKE DUCT DOWNSTREAM OF THE ENGINE AIR FILTER TO THE TURBOCHARGER, THE CAUSE MAY BE A DAMAGED OR INCORRECTLY INSTALLED SEAL. *PE
PB-07-11/64
Service Bulletin/Repair Instructions
MERCEDES-BENZ - MODELS E320, ML320, GL320, R320 - MODEL 2007 - DIAGNOSTIC ENHANCEMENT: OM642 DIESEL ENHANCED DIAGNOSTIC ASSISTANCE CENTER (EDAC). *NJ
424587
Service Bulletin/Repair Instructions
MODEL ML350, ML500, ML63, ML320, ML550, GL450, GL320, GL550 4 MATIC -- EQUIPPED WITH SALES CODE 477 - TIRE LOSS WARNING SYSTEM (INDIRECT ESP BASED) WITH RUN FLAT TIRES -- MODEL YEAR 2005 TO 2007 (TIRE PRESSURE MONITORING INACTIVE) DISPLAYED IN INSTRUMENT CLUSTER. *NJ
2007100003
Service Bulletin/Repair Instructions
MODELS E320, E500, E55, E350, E550, E63, ML350, ML500, ML63, ML320, ML550, GL450, GL320, GL550 WITH DIESEL ENGINE OM 642 MY 2006-2007 -- UPDATE ENGINE CONTROL MODULE SOFTWARE. *NJ
2007110002
Service Bulletin/Repair Instructions
MODELS ML350, ML500, ML63, ML320, ML550, GL450, GL320, GL550, R350, R500, R63, R320 - MY2007-2008. INSTALL REAR ENTERAINMENT SOFTWARE. *NJ
2007080003
Service Bulletin/Repair Instructions
REPLACE CHARGE AIR HOSES (OM642 ENGINE) *NJ UPDATED 2/4/08 *NJ
2007090001
Service Bulletin/Repair Instructions
MERCEDES-BENZ MODELS WITH MECHANICAL MIRRORS - LUBRICATE FOLDING MECHANISM OF RIGHT AND LEFT OUTSIDE MIRRORS. *NJ