Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
LI82.62-P-078631
Service Bulletin/Repair Instructions
Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!
LI35.30-P-058566
Service Bulletin/Repair Instructions
Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).
LI77.21-P-075806
Service Bulletin/Repair Instructions
Complaint The sliding sunroof glass panel of the panoramic roof reverses during the closing process, either once or multiple times, without an entrapment (anti‑pinch) event being detected. The concern may occur temporarily or repeatedly during normal closing operation. Cause The automatic reversing function of the panoramic roof is overly sensitive due to parameterization in combination with seal counter‑pressure. This condition can cause the roof to reverse even though no obstruction is present. Remedy Retrofit the vehicle to meet Cleanpoint status “Panoramic sliding sunroof glass panel reverses during closing without a pinch event.” The retrofit includes: • Hardware modification (installation of a cover rail / EPDM lip) • Corresponding software update for the panoramic roof control unit The prescribed retrofit steps must be performed in the specified sequence as outlined in this document. 1) Retrofit the EPDM lip onto the rear edge of the panoramic sliding roof panel: • Clean the underside of the rear edge of the sliding sunroof panel (marking, Figure 1) (e.g., isopropanol). • Subsequently install the cover rail on the underside of the sliding sunroof panel (Figure 2). - Distance from the cover rail to the rear edge of the sliding sunroof panel A = 5 mm - Distance from the cover rail to the right and left edges of the sliding sunroof panel B = 9 mm - Apply firm pressure by hand along the entire bonding surface of the COVER RAIL - The wider flange at the ends of the cover rail (see Figure 3) must point in the direction of travel 2) Submit an XSS Ticket with the following requests to add SA code O75 to the Vehicle Data Card • Enter code "O75" (Oscar 75) in Vehicle Documentation System (Vedok): • Add the following AO text to KG 78: AO code O75 added as specified in LI77.21-P-075806 (Version 7). 3) Install new software from the panoramic roof control unit (TSSR296, A98, PSD) and teach in the anti-pinch protection again: • Connect XENTRY Diagnosis. - always use the current XENTRY Diagnosis software release with all available add-ons. - Strict compliance with the operation steps in XENTRY Diagnosis is absolutely essential! - Ensure adequate power supply to the vehicle's on-board electrical system battery (greater than 12.5 V) using a battery charger. • Commission the panoramic roof control unit - To do this, select "A98 – control module 'panoramic sliding sunroof' → adaptation → commissioning → Commission the control unit." - Then follow user guidance in XENTRY Diagnosis. • Disconnect XENTRY Diagnosis.
LI82.10-P-078301
Service Bulletin/Repair Instructions
Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304
LI33.30-P-056665
Service Bulletin/Repair Instructions
Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).
LI82.10-P-078896
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.
LI83.20-P-051802
Service Bulletin/Repair Instructions
Complaint Vehicle with atypical reduced heat output. Cause Silicate granulate may have escaped from a damaged bag in the expansion reservoir (not visible), reducing the coolant flow in the heater heat exchanger (see picture). Remedy With the aforementioned complaint, make sure that the cooling circuit is inspected for silicate residues after all standard tests are completed. The silicate residues tend to accumulate upstream of the shutoff valve for the heater hot water pulsed valve. If there are silicate residues in the coolant, the engine must be flushed thoroughly. To make sure that all silicate residues are removed from the cooling circuit, the following parts must also be replaced (cleaning of these components is not sufficient): Coolant expansion reservoir, radiator, oil/water heat exchanger (oil cooler), heater valve, heat exchanger of heater, coolant and, if installed, the electric water pump for the residual heat utilization system. Determine the parts for the respective vehicle in the EPC.
LI82.70-P-077433
Service Bulletin/Repair Instructions
Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
LI82.35-P-078467
Service Bulletin/Repair Instructions
Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
LI82.10-P-078307
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
LI82.10-P-078069
Service Bulletin/Repair Instructions
Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
NCU-2023060005
Service Bulletin/Repair Instructions
Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (âÂÂMYâÂÂ) 2009-2012 GL-Class, ML-Class, R-Class, and S-Class (164/166, 251, 221 platforms) vehicles, the coding for the engine control unit does not correspond to the specifications as part of the âÂÂBlueTEC updateâ diesel field measure (aka âÂÂEmission ModificationâÂÂ). This could result in the VIN number not being read out from the vehicle. This could affect the vehicle smog check. MBUSA will conduct an Emission Service Campaign in which an authorized Mercedes-Benz dealer will update the SCN coding for the engine control unit on the affected vehicles.
LI91.18-P-077075
Service Bulletin/Repair Instructions
Crease formation on genuine leather seat covers in vehicles with low mileage ⢠Objects left on the seats for extended periods of time (pressure marks). ⢠Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). ⢠Light initial creases due to vehicle handling. ⢠Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
LI77.21-P-072113
Service Bulletin/Repair Instructions
Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
LI82.10-P-064766
Service Bulletin/Repair Instructions
Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
NCU - HVAC Warra
Service Bulletin/Repair Instructions
To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
LI35 30-P-058566
Service Bulletin/Repair Instructions
Throttle lift-off clunking noises at drive shafts of rear axle
LI05 20-P-067123
Service Bulletin/Repair Instructions
Oil in engine wiring harness
LI91.29-P-050116
Service Bulletin/Repair Instructions
Play/noises in electric seat adjustment or error messages from WSS sensors
LI8330P0496447
Service Bulletin/Repair Instructions
No cooling output, fault code 9006 stored in air conditioning control unit.
LI8210P0647661
Service Bulletin/Repair Instructions
Headlamps fogged.
RecallUpdate
Service Bulletin/Repair Instructions
Recall Campaign announcement for Takata driver airbags.
LI42.20-P-061327
Service Bulletin/Repair Instructions
Electric parking brake inoperative
LI09.20-P-061233
Service Bulletin/Repair Instructions
Engine diagnosis warning lamp lights up, engine shakes at idle
LI07.08-P-060993
Service Bulletin/Repair Instructions
Engine diagnosis warning lamp lights up in instrument cluster, fault code U145400: "Implausible data were received from the ethanol sensor"
LI91.10-P-050164
Service Bulletin/Repair Instructions
Noises from the mounting of the rear weight sensing system (WSS) sensors
LI27.00-P-059383
Service Bulletin/Repair Instructions
Under certain circumstances, the 2-3 and/or 3-4 upshift can be uncomfortable when the transmission oil is cold.
LI27.19-P-056151
Service Bulletin/Repair Instructions
With an unfavorable sensor position and high rpms, the sensor may deliver incorrect rpm values and the transmission control unit may detect overspeeding. Owing to the software application, the control unit is not reset in the case of implausible messages.
LI91.25-P-059380
Service Bulletin/Repair Instructions
Pneumatic comfort systems with insufficient performance, entirely inoperative or leaky.
LI68.20-P-053607
Service Bulletin/Repair Instructions
Noise in center console area of W166.
LI67.30-P-052837
Service Bulletin/Repair Instructions
Side windows may make noises when closing and opening, or reverse direction when closing.
LI67.30-P-055417
Service Bulletin/Repair Instructions
Side windows may make noises when closing and opening, or reverse direction when closing.
LI68.05-P-059193
Service Bulletin/Repair Instructions
SENTEX gate operator with Clik Card Remote not compatible with Homelink
LI05.10-P-056435
Service Bulletin/Repair Instructions
Rattling noise after engine start for several seconds
LI46.15-P-058505
Service Bulletin/Repair Instructions
Creaking noise when making vertical or longitudinal adjustment to electrical steering column
LI49.20-P-056353
Service Bulletin/Repair Instructions
Engine diagnosis warning lamp active. Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.
C1A140101
Service Bulletin/Repair Instructions
This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
LI14.20-P-052079
Service Bulletin/Repair Instructions
Engine diagnosis warning lamp lights up - Fault code entry (FC) 14A600 or 14A700
GI88.40-P-057430
Service Bulletin/Repair Instructions
Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
S-SC- 2013090008
Service Bulletin/Repair Instructions
This Service Campaign has been initiated because Daimler AG (DAG), the manufacturer of Mercedes-Benz vehicles, has determined that the mbrace software does not correspond to current production configuration. An authorized Mercedes-Benz dealer will update the mbrace control module software at the next workshop visit.
LI32.20-P-057942
Service Bulletin/Repair Instructions
Thumping noises from front axle when driving over bumps on road.
LI8270P055572
Service Bulletin/Repair Instructions
Mobile phone cotacts are not transferred completely.
S-B-67.00-29
Service Bulletin/Repair Instructions
Since 12/2012 (model 166) and since 06/2013 (model 242) the glass breakage loops are no longer in the side windows and rear window. Suitable interior protection ensures that the interior monitoring function continues to operate correctly.
LI82.95-P-056655
Service Bulletin/Repair Instructions
Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
LI82.85-P-055695
Service Bulletin/Repair Instructions
The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
P-B-54.10-225d
Service Bulletin/Repair Instructions
If it is necessary to replace an HV battery, the return will only be accepted with the filled-out ?Analysis Sheet for Transportability of High-Voltage Batteries Form? accompanied by: , the removed part, the quick test printout, the BMS control unit log printout, the repair documentation and with all required documentation listed in Section E of the Form.
LI82.10-P-054588
Service Bulletin/Repair Instructions
Xenon burner inoperative or flickers
LI-72-00-P
Service Bulletin/Repair Instructions
XENTRY: OUTSIDE DOOR HANDLE NO LONGER RETURNS TO END POSITION. DUE TO A BENT PIN IN THE DYNAMIC BALANCER, THE SUPPORT SPRING OF THE BEARING BRACKET CAN SLIDE OUT OF PLACE OR BECOME UNHOOKED. MODELS 164, 251, 166, 204, 212. NO MODEL YEARS LISTED. *PE UPDATED 2/1/12. *PE UPDATED 10/3/12. *PE UPDATED 10/21/13. *PE
LI46-20P-055943
Service Bulletin/Repair Instructions
XENTRY (MERCEDES): RATTLING NOISE COMING FROM THE AREA OF THE STEERING COLUMN TUBE SYSTEM, WHEN DRIVING OVER ROUGH ROAD AND WHEN ACCELERATING OR BRAKING, THERE WOULD BE CRACKING NOISES. MODELS 164, 251. NO MODEL YEARS LISTED. *PE
LI-33-25
Service Bulletin/Repair Instructions
MERCEDES-BENZ: AT THE FRONT WHEEL BEARING THERE IS A LOUD KNOCK SOUND WHEN GOING AROUND A CORNER AT SLOW SPEEDS. THERE IS AN INSUFFICIENT FIT AT THE BEARINGS. *RM UPDATED 10/14/11. *PE UPDATED 6/19/13. *PE
LI46-10P-054715
Service Bulletin/Repair Instructions
MERCEDES (XENTRY): DUE TO AMINE DEPOSITS FROM STEERING WHEEL FOAM, HORN PLATE OF STEERING WHEEL, SHORT CIRCUITED, CAUSING THE MULTIFUNCTION BUTTONS, ON STEERING WHEEL, TO BE NON-FUNCTIONAL. MODELS 164, 251. NO MODEL YEARS LISTED. *PE
LI-91-40-P050718
Service Bulletin/Repair Instructions
XENTRY(MERCEDES): BULLETIN PROVIDED REGARDING CONTROL UNIT DETECTING AN UNDERVOLTAGE AFTER BUCKLING UP (BELT SLACK ELIMINATION) DURING SEAT BELT ADJUSTMENT SEQUENCE. *PE UPDATED 5/23/12. *JS
LI46-20-P051767
Service Bulletin/Repair Instructions
MERCEDES-BENZ: THE STEERING IS LEAKING IN THE INPUT SHAFT, BELOW THE PROTECTIVE CAP. THERE IS WEAR ON A SEAL RING LOCATED IN THE CONTROL HEAD. *RM UPDATED 5/17/2012 *JS
LI-27-60-P049270
Service Bulletin/Repair Instructions
MERCEDES-BENZ: THE AUTO-TRANSMISSION SWITCHES TO LIMP HOME MODE OR HAS NO POWER. THERE ARE MULTIPLE POSSIBLE FAULT CODES. A PISTON MAY BE DAMAGED. *RM
LI-68-50
Service Bulletin/Repair Instructions
MERCEDES-BENZ: THE LOAD COMPARTMENT ROLLER BLIND HAS CATCH BOLTS LOOSE OR BROKEN FROM IMPROPER FORCE WHEN USING. *RM
LI-07-08
Service Bulletin/Repair Instructions
MERCEDES-BENZ: THE STARTER CLICKS BUT DOES NOT CRANK WHEN TRYING TO START. A VOLTAGE DIP IS CAUSING THE IGNITION PROCEDURE TO FAIL. *RM
LI-80-57
Service Bulletin/Repair Instructions
MERCEDES-BENZ: DIAGNOSTIC PROCEDURES FOR THE DRIVER AUTHORIZATION SYSTEM. *RM
SB-20101100005
Service Bulletin/Repair Instructions
MERCEDES-BENZ: SOFTWARE UPDATE FOR HEATER LINES. *RM
SB-32-25-82
Service Bulletin/Repair Instructions
MERCEDES-BENZ: SHOCK ABSORBER PROCEDURE. *RM
SB-91-60-193
Service Bulletin/Repair Instructions
MERCEDES: AIRBAG DURABILITY AND RELIABILITY. AIR BAG SRS CONTROL MODULE (N2/2) DOES NOT HAVE A SET SHELF LIFE AND WILL NORMALLY BE RELIABLE FOR THE LIFE OF A VEHICLE. WITH 164, 216 221, 251 AND NEWER, THE AIRBAG CONTROL UNIT CAN BE RESET FIVE TIMES. WITH MODES 202, 210 AND NEWER, THE AIRBAG CONTROL UNIT CAN BE RESET THREE TIMES. EARLIER MODELS WOULD HAVE TO HAVE THEIR AIRBAG CONTROL UNIT AND TRIGGERED RESTRAIN COMPONENTS CHANGED ONLY AFTER AN ACCIDENT. NO MODELS OR MODEL YEARS LISTED. *PE
P-049567
Service Bulletin/Repair Instructions
MERCEDES: BATTERY SYMBOL AND SERVICE REQUIRED (IN WHITE). FAULT MESSAGE IS DISPLAYED IF THE CHARGE LEVEL IS TOO LOW OR THE PARK PAWL ADDITIONAL BATTERY IS DEFECTIVE. IN ADDITION FAULT CODE FC 9061 AND/OR FC 9062 IS STORED IN THE FRONT SAM. *PE
LI-47-30
Service Bulletin/Repair Instructions
MERCEDES (XENTRY): ENGINE DIAGNOSIS WARNING LAMP ACTIVATED. MAGNETIC SHORT BETWEEN ARMATURE AND POLE CORE DUE TO CALIBRATION ERROR AT VALVE AND TOLERANCE DEVIATION BY SUPPLYING MANUFACTURER. THIS CAUSES THE PURGE VALVE TO JAM IN THE OPEN STATE. *PE
SB-91-40-192
Service Bulletin/Repair Instructions
MERCEDES: REPLACING THE EMERGENCY TENSIONING RETRACTOR. WHEN REPLACING THE LEFT FRONT REVERSIBLE EMERGENCY TENSIONING RETRACTOR (A76) OR THE RIGHT FRONT REVERSIBLE EMERGENCY TENSIONING RETRACTOR (A76/1), RETURN THE DAMAGED PART TO THE QEC WITH THE WARRANTY PARTS RETURN SLIP AND WITH THE QUICK TEST REPORT. *PE
LI03-20-P-048278
Service Bulletin/Repair Instructions
MERCEDES (XENTRY): ENGINE MAKES NOISE, TICKING/CRACKLING AT IDLE SPEEDS UP TO APPROX. 1500 RPM. RUN IN EFFECT OF 1ST CRANKSHAFT MAIN BEARING. MODELS 211, 219, 164, 251, 203, 204, 209, 221, 461 AND 463. NO MODEL YEARS LISTED. *PE
LI91-22-P-048771
Service Bulletin/Repair Instructions
MERCEDES: THE ELECTRICALLY FOLDING 3RD SEAT ROW MAKES NOISES WHILE FOLDING UP AND DOWN, OR THE FOLDING FUNCTION DOES NOT WORK AT ALL. A WARNING MESSAGE ABOUT LOCKING THE 3RD SEAT ROW MAY ALSO APPEAR IN THE DISPLAY. *PE
LI-58-40
Service Bulletin/Repair Instructions
XENTRY (MERCEDES): ENGINE WARNING LAMP IS CURRENTLY ON OR WAS ON AND A DELAY FAULT OF THE CAMSHAFT ADJUST TO CURRENT OR STORED IN THE ENGINE CONTROL UNIT. MODELS 171, 203, 209, 211, 219, 221, 216, 230, 164, 251, AND 403. NO MODEL YEARS LISTED. *PE
SB-2009120003
Service Bulletin/Repair Instructions
MERCEDES BENZ: CHECK COOLANT PROTECTION LEVEL OF THE HYBRID POWER ELECTRONICS MODULE AND HIGH VOLTAGE BATTERY, CORRECT IF NECESSARY. MODEL AND MY 164 2010. *PE
TB-P-047927
Service Bulletin/Repair Instructions
MERCEDES: FOLLOWING FAULT CODES ARE ENTERED IN THE CONTROL UNIT AND DISPLAYED-FC5320 DRAIN VALVE:OPEN CIRCUIT OR INSUFFICIENT VALVE CURRENT IN MODELS SERIES 211, 219; FC5260 DRAIN VALVE OPEN CIRCUIT OR INSUFFICIENT VALVE CURRENT IN MODEL 221; FC5250 DRAIN OPEN CIRCUIT OR INSUFFICIENT VALVE CURRENT IN MODEL SERIES 251, 164. DEFECTIVE CONNECTING CABLES TO DRAIN VALVE AT AIRMATIC COMPRESSOR. THIS RESULTS IN THE SETTING OF THE FAULT CODES. NO MODEL YEARS LISTED. *PE
SB-47-20-56
Service Bulletin/Repair Instructions
MERCEDES: ENSURING UNOBSTRUCTED MOVEMENT FOR THE FUEL LEVEL SENSOR. WHEN INSTALLING THE LEFT OR RIGHT FUEL LEVEL SENSOR, IT IS ESSENTIAL FOR IT TO HAVE UNRESTRICTED, UNOBSTRUCTED MOVEMENT. *PE
TSB-42-10-109
Service Bulletin/Repair Instructions
MERCEDES: CORROSION PROTECTION COATINGS FOR BRAKE COMPONENTS AND HARDWARE MAY BE DAMAGED AND OR STRIPPED AWAY IF HIGHLY CONCENTRATED ACID BASED CLEANERS ARE USED. ONCE THE CORROSION PROTECTION IS DAMAGED OR REMOVED THE BRAKE COMPONENTS AND OR HARDWARE CAN BEGIN TO CORRODE. INCLUDE ALL MODELS AND MODEL YEARS. *PE
SB-01-20-24A
Service Bulletin/Repair Instructions
MERCEDES: WHISTLING SOUND FROM ENGINE COMPARTMENT. THE SOUND CAN ALSO BE HEARD FOR UP TO SEVERAL SECONDS AFTER THE ENGINE IS SWITCHED OFF. MODELS ML63, C63, CLK63 (CABRIOLET), E63, E63S, CL63, CLS63, S63, SL63 AND R63. NO MODEL YEARS LISTED. *PE
TSB-2009020004
Service Bulletin/Repair Instructions
MERCEDES: IT HAS BEEN DETERMINED THAT THE TELE AID MAY NOT FUNCTION PROPERLY AS A RESULT OF A HARDWARE FAULT IN THE TELE AID CONTROL MODULE. IF THIS CONDITION EXISTS AN INSTRUMENT CLUSTER MESSAGE OF NO SERVICE AND TELE AID INOPERABLE WILL BE SEEN. *PE