Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
LI82.62-P-078631
Service Bulletin/Repair Instructions
Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!
LI35.30-P-058566
Service Bulletin/Repair Instructions
Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).
LI82.30-P-059239
Service Bulletin/Repair Instructions
Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).
LI35.10-P-078931
Service Bulletin/Repair Instructions
Complaint Potential corrosion on the rear axle carrier Cause Due to market-specific conditions such as moisture, ingress of dirt and/or environmental influences, corrosion can occur on the rear axle carrier Remedy In the event of a complaint, the optimized repair method must be used when replacing the rear axle carrier. The repair method for the respective model series can be found in the attachment. Repair packages are available in Xentry Repair Packages for the special processing of rear axle carriers Note: Please utilize flexible wand (319-SAT1058826) along with the Cavity Preservation Gun (W 000 588 03 72 00) for cavity wax application to improve coverage and reduces labor efforts. The flexible wand may be obtained through the Mercedes-Benz Standard Service Equipment Program website.
LI77.21-P-075806
Service Bulletin/Repair Instructions
Complaint The sliding sunroof glass panel of the panoramic roof reverses during the closing process, either once or multiple times, without an entrapment (anti‑pinch) event being detected. The concern may occur temporarily or repeatedly during normal closing operation. Cause The automatic reversing function of the panoramic roof is overly sensitive due to parameterization in combination with seal counter‑pressure. This condition can cause the roof to reverse even though no obstruction is present. Remedy Retrofit the vehicle to meet Cleanpoint status “Panoramic sliding sunroof glass panel reverses during closing without a pinch event.” The retrofit includes: • Hardware modification (installation of a cover rail / EPDM lip) • Corresponding software update for the panoramic roof control unit The prescribed retrofit steps must be performed in the specified sequence as outlined in this document. 1) Retrofit the EPDM lip onto the rear edge of the panoramic sliding roof panel: • Clean the underside of the rear edge of the sliding sunroof panel (marking, Figure 1) (e.g., isopropanol). • Subsequently install the cover rail on the underside of the sliding sunroof panel (Figure 2). - Distance from the cover rail to the rear edge of the sliding sunroof panel A = 5 mm - Distance from the cover rail to the right and left edges of the sliding sunroof panel B = 9 mm - Apply firm pressure by hand along the entire bonding surface of the COVER RAIL - The wider flange at the ends of the cover rail (see Figure 3) must point in the direction of travel 2) Submit an XSS Ticket with the following requests to add SA code O75 to the Vehicle Data Card • Enter code "O75" (Oscar 75) in Vehicle Documentation System (Vedok): • Add the following AO text to KG 78: AO code O75 added as specified in LI77.21-P-075806 (Version 7). 3) Install new software from the panoramic roof control unit (TSSR296, A98, PSD) and teach in the anti-pinch protection again: • Connect XENTRY Diagnosis. - always use the current XENTRY Diagnosis software release with all available add-ons. - Strict compliance with the operation steps in XENTRY Diagnosis is absolutely essential! - Ensure adequate power supply to the vehicle's on-board electrical system battery (greater than 12.5 V) using a battery charger. • Commission the panoramic roof control unit - To do this, select "A98 – control module 'panoramic sliding sunroof' → adaptation → commissioning → Commission the control unit." - Then follow user guidance in XENTRY Diagnosis. • Disconnect XENTRY Diagnosis.
LI82.10-P-078301
Service Bulletin/Repair Instructions
Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304
LI82.10-P-078307
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
LI82.10-P-078896
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. **NOTE - As of Sept 2025 the pressure testing tool is not finalized and may require modifications to fit properly. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.
LI33.30-P-056665
Service Bulletin/Repair Instructions
Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts
LI83.20-P-051802
Service Bulletin/Repair Instructions
Complaint Vehicle with atypical reduced heat output. Cause Silicate granulate may have escaped from a damaged bag in the expansion reservoir (not visible), reducing the coolant flow in the heater heat exchanger (see picture). Remedy With the aforementioned complaint, make sure that the cooling circuit is inspected for silicate residues after all standard tests are completed. The silicate residues tend to accumulate upstream of the shutoff valve for the heater hot water pulsed valve. If there are silicate residues in the coolant, the engine must be flushed thoroughly. To make sure that all silicate residues are removed from the cooling circuit, the following parts must also be replaced (cleaning of these components is not sufficient): Coolant expansion reservoir, radiator, oil/water heat exchanger (oil cooler), heater valve, heat exchanger of heater, coolant and, if installed, the electric water pump for the residual heat utilization system. Determine the parts for the respective vehicle in the EPC.
LI82.70-P-077433
Service Bulletin/Repair Instructions
Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
LI82.35-P-078467
Service Bulletin/Repair Instructions
Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
LI82.10-P-078302
Service Bulletin/Repair Instructions
Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
LI82.10-P-078069
Service Bulletin/Repair Instructions
Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
NCU - 24240304
Service Bulletin/Repair Instructions
As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customerâÃÂÃÂs contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
LI91.18-P-077075
Service Bulletin/Repair Instructions
Crease formation on genuine leather seat covers in vehicles with low mileage ⢠Objects left on the seats for extended periods of time (pressure marks). ⢠Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). ⢠Light initial creases due to vehicle handling. ⢠Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
CL-ELWSubframe
Service Bulletin/Repair Instructions
Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
ELW-RearSubframe
Service Bulletin/Repair Instructions
Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
LI82.10-P-064766
Service Bulletin/Repair Instructions
Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
NCU - HVAC Warra
Service Bulletin/Repair Instructions
To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
P-SC-2017030011
Service Bulletin/Repair Instructions
Replace Driver-Side and (if applicable) Front Passenger Air Bag
LI46.10-P-055432
Service Bulletin/Repair Instructions
AMG Performance steering wheel heavily worn/soiled
TakataRecall
Service Bulletin/Repair Instructions
Additional information around the recent recall announcement affecting approximately 705,983 Mercedes-Benz passenger vehicles involving Takata driver-side airbags containing PSDl-5 type inflators
RecallUpdate
Service Bulletin/Repair Instructions
Recall Campaign announcement for Takata driver airbags.
LI82.70-P-060004
Service Bulletin/Repair Instructions
iPhone mobile phone: Various complaints after software update to iOS8
LI91.25-P-059385
Service Bulletin/Repair Instructions
The lumbar support cannot be set from stage 0 to stage 5. Stage 5 can only be set after setting stage 10 first
LI91.25-P-059380
Service Bulletin/Repair Instructions
Pneumatic comfort systems with insufficient performance, entirely inoperative or leaky.
LI82.85-P-058582
Service Bulletin/Repair Instructions
Apple products (iPhone or iPod) are not charged via the serial USB interface of the COMAND Online control unit (A40/3) in the stowage compartment of the center console.
LI46.15-P-058505
Service Bulletin/Repair Instructions
Creaking noise when making vertical or longitudinal adjustment to electrical steering column
C1A140101
Service Bulletin/Repair Instructions
This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
LI77.30-P-056644
Service Bulletin/Repair Instructions
Water entry through front section of retractable hardtop with the following localization: - Partial water entry in the area of the side seals to the A-pillar (for area see Fig. 1) when accelerating/braking the vehicle.
LI27.00-P-056643
Service Bulletin/Repair Instructions
During disengagement from D to N and/or from R to N some slight jolting could be experienced.
LI82.95-P-056655
Service Bulletin/Repair Instructions
Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
LI82.85-P-055695
Service Bulletin/Repair Instructions
The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
SC-2012070002
Service Bulletin/Repair Instructions
MERCEDES: CAMSHAFT ADJUSTMENT SOLENOID MAY LEAK OIL DUE TO SETTLING PROPERTIES OF SEAL AND THE ENGINE WIRING HARNESS WILL BE RETROFITTED WITH FOUR ADAPTER HARNESSES AS A PRECAUTIONARY MEASURE. MODELS 2005-2011 164, 171, 203, 204, 207, 209, 211, 212, 216. 219, 221, 230, 251, 463. *PE UPDATED 12/18/12. *PE UPDATED 3/18/2013 *JS
LI-05-20-P
Service Bulletin/Repair Instructions
MERCEDES-BENZ: THE MALFUNCTION LIGHT IS ON WITH MULTIPLE POSSIBLE TROUBLE CODES STORED. THERE COULD BE A PROBLEM WITH THE CAMSHAFT AND/OR SCORING OF A PISTON. *RM
LI-27-60
Service Bulletin/Repair Instructions
MERCEDES-BENZ: RATTLING NOISE AT THE SHIFT ROD. *RM
LI-88-70
Service Bulletin/Repair Instructions
MERCEDES BENZ: THE TURN SIGNAL LIGHT ON THE MIRROR FOGS UP DUE TO TEMPERATURE DIFFERENCES. *RM
LI-80-57
Service Bulletin/Repair Instructions
MERCEDES-BENZ: DIAGNOSTIC PROCEDURES FOR THE DRIVER AUTHORIZATION SYSTEM. *RM
SB-32-25-82
Service Bulletin/Repair Instructions
MERCEDES-BENZ: SHOCK ABSORBER PROCEDURE. *RM
LI-58-40
Service Bulletin/Repair Instructions
XENTRY (MERCEDES): ENGINE WARNING LAMP IS CURRENTLY ON OR WAS ON AND A DELAY FAULT OF THE CAMSHAFT ADJUST TO CURRENT OR STORED IN THE ENGINE CONTROL UNIT. MODELS 171, 203, 209, 211, 219, 221, 216, 230, 164, 251, AND 403. NO MODEL YEARS LISTED. *PE
TSB-42-10-109
Service Bulletin/Repair Instructions
MERCEDES: CORROSION PROTECTION COATINGS FOR BRAKE COMPONENTS AND HARDWARE MAY BE DAMAGED AND OR STRIPPED AWAY IF HIGHLY CONCENTRATED ACID BASED CLEANERS ARE USED. ONCE THE CORROSION PROTECTION IS DAMAGED OR REMOVED THE BRAKE COMPONENTS AND OR HARDWARE CAN BEGIN TO CORRODE. INCLUDE ALL MODELS AND MODEL YEARS. *PE
470036
Service Bulletin/Repair Instructions
MERCEDES: THE FUEL LEVEL INDICATED IN THE INSTRUMENT CLUSTER DOES NOT MATCH THE ACTUAL FILL LEVEL. THIS MAY BE CAUSED BY A FAULT IN THE FUEL LEVEL SENSOR FUNCTION CHAIN: HYDRAULIC AND ELECTRICAL LINES AND THEIR CONNECTIONS, REAR SAM OR INSTRUMENT CLUSTER. *TT UPDATED 2/23/09. *PE UPDATED 9/18/09. MODEL YEARS UNKNOWN. *PE
SB-40-15-68
Service Bulletin/Repair Instructions
MERCEDES: THE INSTRUMENT CLUSTER DISPLAYING TIRE PRESSURE MONITOR INOPERATIVE AND THERE IS A CORRESPONDING STORED FAULT CODE OF 5581 (FRONT OR REAR SENSOR LOCALIZATION FAILED), THIS IS BECAUSE THE DIFFERENCE IN THE SIGNAL STRENGTH BETWEEN THE FRONT AND REAR AXLE MAY NOT BE ENOUGH FOR THE WHEEL ASSIGNMENTS TO BE ACCURATELY MADE. NO MODEL YEARS LISTED. *PE
TSB-2009020004
Service Bulletin/Repair Instructions
MERCEDES: IT HAS BEEN DETERMINED THAT THE TELE AID MAY NOT FUNCTION PROPERLY AS A RESULT OF A HARDWARE FAULT IN THE TELE AID CONTROL MODULE. IF THIS CONDITION EXISTS AN INSTRUMENT CLUSTER MESSAGE OF NO SERVICE AND TELE AID INOPERABLE WILL BE SEEN. *PE
PB-35-31-05
Service Bulletin/Repair Instructions
MERCEDES BENZ: MODEL 171.454, 456 (2005-2008) SLK CLASS; 204.054, 056, 081 (2008) C CLASS; 211.022, 056, 072, 087, 090 (2006-2008) E CLASS. VEHICLES PRODUCED BETWEEN 2/21/08 AND 4/3/08 WITH DIFFERENTIAL SERIAL NUMBER 1824214 TO 1865328. CLUNKING NOISE DURING LOAD CHANGE AT REAR AXLE DIFFERENTIAL. *PE
2008030003
Service Bulletin/Repair Instructions
MERCEDES BENZ: CHECK WINDSHIELD WIPER SHAFT GROMMET, CORRECT INSTALLATION IF NECESSARY. WINDSHIELD WIPER SHAFTS MAY NOT HAVE BEEN PROPERLY INSTALLED. MODEL 171. *PE
033008
Service Bulletin/Repair Instructions
CHECK ENGINE LIGHT ON / FAULT CODES FC1200 / FC1208 STORED IN ME-SFI CONTROL UNIT. MERCEDES-BENZ MODEL C230, C280, C350, SLK280, SLK350, CLK350, CLK550, E350, E550, CLS550, S600, AND SL550. EQUIPPED WITH M272 ENGINE OR M273 ENGINE. *NJ UPDATED 8/28/08. *PE
2008030002
Service Bulletin/Repair Instructions
CHECK SPRING ON SECONDARY HOOD LATCH, REPLACE HOOD LATCH IF NECESSARY - MODEL SLK350, SLK55, SLK280, MODEL YEAR 2008. *NJ