Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
LI46.35-P-067339
Service Bulletin/Repair Instructions
Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!
LI72.20-P-075746
Service Bulletin/Repair Instructions
Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double‑clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.
LI54.71-P-079104
Service Bulletin/Repair Instructions
Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("‑ ‑"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the re‑check function in the same location. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: • Video of the concern. • Exact location (latitude and longitude is best)
LI72.00-P-080885
Service Bulletin/Repair Instructions
Complaint The Dark Chrome finish on the retractable door handle appears discolored, stained, or faded. The discoloration is typically visible along the upper surface of the handle. Cause Insufficient surface treatment of the black chrome from the supplier Remedy 1.) Clean door handles. 2.) Inspect the handle after cleaning. • Confirm that the discoloration remains clearly visible across the upper portion of the handle. • Compare the condition to the LI reference photos 3.) If the discoloration matches the fault profile shown in the reference photos → replace the affected retractable door handle.
LI82.85-P-079088
Service Bulletin/Repair Instructions
Complaint The following most common complaints may be observed: • Brief connectivity interruptions when using Apple CarPlay over Wi-Fi • Audio cuts out • Device not recognized • No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicle’s head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference External Sources: • Passing under toll bridges, driving near airports, or areas with heavy electronic interference (e.g., as described in LI82.85-P-076157) can cause connection drops. Cellular Networks: • Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: • Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Issues Head Unit Software/Hardware: • Outdated firmware, bugs, or hardware faults in the vehicle’s head unit can prevent a stable connection. iPhone Software/Hardware: • Similar issues in the iPhone, including buggy iOS updates or hardware problems, may affect performance. Reset or Reboot:• Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings Wired Connections: • Faulty Cable: A damaged or poor-quality USB cable can cause intermittent or total loss of connection. • USB Port Issues: Dust, debris, or physical damage in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: • Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: • Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. • Vehicle’s Electrical System: Unstable power delivery from the car’s battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration Phone Settings: • Incorrect or conflicting settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. • Third-Party Apps/Profiles: • Installed apps or configuration profiles may conflict with CarPlay’s operation. • Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: • Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: • Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors Heat & Overheating: • If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: • Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy FUP6 (E605.8) software has been released for the following chassis: 118, 177, 243,247,206,254,167,294,295,296,223, 297. Flash available software for the head unit and test for function. The LI will be updated once available for the remaining chassis. If the complaint remains after the SW update please continue with the steps below. Guided Diagnostic Path for Apple CarPlay Connection Issues: Please follow the steps below to systematically diagnose and resolve CarPlay concerns:Update Devices: • Ensure the iPhone is updated to the latest available iOS version. • Ensure the vehicle’s head unit is updated to the latest software version available. Isolate the Issue: • Check whether the symptom persists with another iPhone running the latest iOS version. • Test both wireless and wired CarPlay connections: • Does the issue only occur with wireless CarPlay? • Does the wired connection to the phone function correctly? Further Troubleshooting Steps: • Reboot the iPhone. See attachment for further instructions.
LI54.10-P-080880
Service Bulletin/Repair Instructions
Complaint Customer Complaint: - AC charging is not possible. - The departure time, charging pause, location-based charging or target SOC limit is automatically set to 50% or to a random value in the Mercedes me application or in the charging settings on the head unit display. (Picture 1 & 3) - Incorrect notifications appear in the Mercedes me application for charging-related functions. (Picture 2) Related DTCs in quick test: No related fault codes (DTCs) are stored in the relevant control units. CPC3 - N127 (Drivetrain control unit) OBL223_GEN4 - N83/11 (Alternating current charger for high-voltage battery) DCB223 - N116/5 - Direct current charge connection unit (DCCU) Picture1 The target SOC limit is automatically set to 50% or any random values during charging. Picture 2 Incorrect notification Example “Unable to unlock charging cable. Picture 3 Incorrect settings of charge interruption or pause. (If applicable) Cause - The Customer shares their Mercedes me credentials (password) with a third-party application, for example, a wall box application. This causes the Mercedes Benz backend server to receive random requests to reset the maximum SOC, departure time, charging pause, etc. - Charging settings are set incorrectly, for example, incorrect departure time, charging program, charging interruption/ pause, etc. Remedy The remedies below may vary depending on the customer complaint. Refer to the remedy that best matches the customer complaint. Remedy 1: The target SOC limit is automatically set to 50% or to random values during charging. - Change the Mercedes me login password on the Mercedes me homepage. (My Account > Login and Security > Reset). (Refer to Annex 1). Previously granted authorizations should then be revoked so that the charging settings can no longer be changed by external applications. Advise customers not to share the new password again. - Are there any sub-users? If yes, revoke their rights and reassess the function. -If differences between the vehicle and the Mercedes me app are visible, a new synchronization is recommended. Turn off Digital Extras through the Mercedes me app or the MMCR portal, and then turn the services on again. Remedy 2: Incorrect notifications in the Mercedes me app for charging-related functions. - Restart synchronization between the app and backend. Turn off Digital Extras through the Mercedes me app or the MMCR portal, and then turn the services on again. (Refer to Annex 2) Remedy 3: Incorrect charge interruption or pause setting. - Perform a factory reset of the head unit (A26/17). (Home > Functions > System > Reset), or turn off/correct all charging settings. (Refer to Annex 3) Additional Information: (Good to know) The LED on the charging inlet or socket indicates whether charging is completed or paused. 1) If the target SOC is reached, the charging inlet LED lights up Blue/Green without flashing. 2) If charging is paused, the charging inlet LED lights up orange without flashing. Additionally, the head unit charging settings display a charging pause. Note: Do not replace any hardware components for these complaints. If the complaint cannot be solved, please contact via TIPS or CAC.
LI54.65-P-080132
Service Bulletin/Repair Instructions
Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.
LI54.10-P-080881
Service Bulletin/Repair Instructions
Complaint AC and DC charging are not possible. The white LED on the charging inlet completely goes OFF after plugging in the charging cable. Related DTCs in quick test: There are no related fault codes (DTCs) stored in relevant control units. CPC3 - N127 (Drivetrain control unit) OBL223_GEN4 - N83/11 (Alternating current charger for high-voltage battery) DCB223 - N116/5 - Direct current charge connection unit (DCCU) Cause Control pilot (CP) circuit in DCB (N116/5: Direct current charge connection unit) might be not functional due to electrical overstress from EVSE (Electric Vehicle Supply Equipment | Charging Station). Remedy Refer to the charging cable actual values in DCB (N116/5). The actual value “Charging cable at charging station” and “status of pilot function” shows “Charging cable NOT PLUGGED IN” & “CP not connected” respectively, even though the charging cable is connected on both sides. This confirms a possible breakdown of Control Pilot (CP) circuit inside the DCB. Measurement of the resistance of Proximity Pilot (PP) and Control Pilot (CP) at the charging socket (G10) (see Annex “Resistance measurement Proximity Pilot (CP) and Control Pilot (CP)”)
LI82.62-P-078631
Service Bulletin/Repair Instructions
Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!
LI35.30-P-058566
Service Bulletin/Repair Instructions
Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).
LI33.20-P-078406
Service Bulletin/Repair Instructions
Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
LI82.60-P-080383
Service Bulletin/Repair Instructions
Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.
PSL-NCU Return Parts 7/3
Other
Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 23rd, 2026. After July 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.
LI00.20-P-077615
Service Bulletin/Repair Instructions
Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. The following applies to model series 167 from AEJ 22/1 onward, 192 AMG, 206, 214, 223, 232 AMG, 236, 254, 290 AMG from AEJ 23 onward, 294, 295, 296, 297 and 465: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.
LI54.30-P-080649
Service Bulletin/Repair Instructions
Complaint General information on the operation of the PRE-SAFE® Impulse system: The PRE-SAFE® Side Impulse system is a preventive, i.e. pre-collision occupant protection system. The task of the system is to provide additional protection to vehicle occupants when there is a risk of a side impact. It is not a restraint system component in the conventional sense and does not contain an detonator. A potential side-impact situation is detected by radar sensors. If the system detects an existing likelihood of a side impact, a reversible air cushion in the outer seat side bolster is briefly inflated by opening a valve. The resulting pulse preemptively increases the distance between the door and the occupant in order to move the occupant out of the danger zone. If the system has been activated, the following message appears on the instrument cluster: PRE-SAFE® Side Impulse inoperative. See Operator's Manual. Note: After system activation, diagnostic entry B1B3713 or B1B3813 is marked as active and stored in the ORC223 (N2/5) control unit. Cause After activation of the “PRE-SAFE® Side Impulse” system, the function is no longer available. Remedy Please check the tight seating and possible damage of the radar sensors B29/11 or B29/12. Then replace the gas generator on the affected side (R12/65 or R12/66). After replacing the gas generator (R12/65 or R12/66), please perform commissioning and SCN coding of the radar sensors B29/11 or B29/12 to ensure they are up to date. Note: In principle, it is not necessary to replace the air cushion in the "PRE-SAFE® Side Impulse" system, as it is designed for multiple activations (up to 10). Exception: After deployment of the sidebag (e.g., following a crash), exchange (air cushion with gas generator) of the "PRE-SAFE ® Impulse Side" is required in all cases.
LI83.70-P-078292
Service Bulletin/Repair Instructions
Complaint Red warning message in instrument cluster: "Towing not allowed, see Operator's Manual, consult workshop without starting the engine again". Cause Missing diaphragm on high voltage PTC (interior heating) N33/14 component part results in moisture buildup in the installation space for the heater and causes an insulation fault. The entry of moisture into the high voltage PTC (interior heating) N33/14 in the high voltage wiring harness to the DC/DC converter N83/1 causes a slow-acting insulation fault. This may occur sporadically only to start with before actively developing over time. Remedy Exchange high voltage PTC (interior heating) N33/14 with new part with diaphragm (production date as from 22T231, see component part label). If necessary, and after further testing/measurement, replace wiring harness for DC/DC converter N83/1 to high voltage PTC (interior heating) N33/14. Note: According to the Replacement Parts Department only high voltage PTCs (interior heating) with a diaphragm and with production date as from 22T231 are available! This Li only applies to vehicles with PN A 000 835 83 03 installed. If the vehicle has another part number installed, this does not apply.
LI00.20-P-078424
Service Bulletin/Repair Instructions
Complaint The remaining time shown on the instrument cluster in the workshop menu (days to next due service) is implausible (>365 days) for the following conditions: • for the date of the vehicle handover • or the last conducted and confirmed Service A/B Cause Case 1: Observe the following on vehicles with a disconnected on-board electrical system battery (12V/48V): • The period in which the on-board electrical system battery is disconnected cannot be counted by the maintenance computer. • As soon as the on-board electrical system battery is connected again, the maintenance computer automatically starts counting without making a correction to the remaining time (days until the next service). Case 2: If a disconnected on-board electrical system battery (12V/48V) can be ruled out as the cause, it is possible that: The daily turnover counter inside the electronic ignition lock (EIS) has experienced memory loss. This anomaly was detected in the EIS software from modification year 2022 onward. To do this, please check the plausibility of the daily turnover counter as follows: If "TUSZ Assyst Plus" < the actual days since "Handover Date/DAY/Month/Year," then proceed to remedy for case 2. Information: A variation of 2-3 days is still considered plausible. If "TUSZ Assyst Plus" is plausible, or if a remaining time of 365 days is permanently displayed, check whether the vehicle has been handed over. These types of cases have different causes. (The respective values are included in the maintenance data in the control unit log of the instrument cluster). Remedy For case 1: When the on-board electrical system battery is disconnected, this period must always be taken into account for these vehicles, and the following condition must be met for a correct calculation to be made: • (A): The number of days from the "date of vehicle handover or last service A/B" to the "date on which the vehicle arrived at the workshop." • (B): Remaining time (days until the next service, as shown in the instrument cluster). • (C): Days on which the on-board electrical system battery was disconnected. The formula requires the following condition to be complied with. 365 - (A) [days] = (B) - (C) [days] For case 2: If the on-board electrical system battery (12 V/48 V) was not disconnected and the remaining time shown in the customer or workshop menu on the instrument cluster (days until the next service) is implausible in terms of the date of the vehicle handover or the last performed and confirmed service A/B, or the condition in the formula was not met, the service can still be performed and confirmed. For vehicles arriving more than 90 days after the service due date, the DSB service history can only be corrected by re-entering "Vehicle regularly serviced." A software fix for the EIS (electronic ignition lock) is currently in planning. The objective is to have a remedy available for 2026. Until the remedy is available, it is advisable to inform the customer that the next service is due again after 365 days at the latest.
LI46.15-P-070510
Service Bulletin/Repair Instructions
Complaint Noises from the area of the steering column. - Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. • Instrument panel support • Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: • Position of height and longitudinal adjustment when the noise occurs • If possible, locate affected component part on steering column • State any change in the noise when steering column component parts are touched (e.g. spring, etc.)
LI82.30-P-059239
Service Bulletin/Repair Instructions
Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).
LI91.10-P-076097
Service Bulletin/Repair Instructions
Complaint Play/noise at height adjuster or in seat guide rail on front seats Cause Tolerances and variations in the manufacturing process Remedy 1. Inspect Seat Height Adjuster Barcode Label (See Pic.1) • Locate the barcode label on the cross tube of the seat height adjuster. • In isolated cases, the barcode label may be located on the front side of the cross tube. If not visible, remove the seat cushion to access the label. 2. Evaluate Production Status If Production Status is LOWER than E108 # Replace the seat frame base with the height adjuster motor. If Production Status is E108 or HIGHER # Do NOT replace parts. Please submit a TIPS case to the Body/Chassis/Entertainment inbox and attach: • Video of the noise concern • Photo of the barcode label To improve analysis quality, ensure the video meets the following criteria: • Seat installed in the vehicle • Quiet workshop environment • Steady and smooth camera movement • Good lighting on the suspected noise area • Recording with two people (one filming, while the other is creating the noise-causing movement) • Noise#causing movement must be clearly visible • Camera position: From the rear footwell, looking forward at the front seat • Verbal explanation included in English or German
PSL-NCU Return Parts 4/24
Other
The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, May 14, 2026. After May 14th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.