Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
LI72.20-P-075746
Service Bulletin/Repair Instructions
Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double‑clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.
CL - Tank Leak Detection
Warranty Program/Extension
Dear Mercedes-Benz Owner: In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. • If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. • This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.
LI01.20-P-080884
Service Bulletin/Repair Instructions
Complaint Oil leaks found on M176 or M177 engines diagnosed to be from the cylinder head cover area Cause Unknown (under investigation) Remedy If oil leaks are found at left or right cylinder head cover area please collect the following information and open TIPS case. 1. Collect photos of the leak 2. Include close up and wide view photos to accurately represent the location 3. Include if the vehicle has a "check oil level" Light on in the cluster or fault codes 4. Check oil level as per WIS to verify level and calculate possible oil loss from the leak 5. Identify and communicate the severity of the leak and provide supporting documentation 6. Open a TIPS case with the above information and submit to the Powertrain team for processing
LI82.62-P-078631
Service Bulletin/Repair Instructions
Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!
LI27.00-P-075630
Service Bulletin/Repair Instructions
Complaint This document is intended as a pre-case diagnostic reference for transmission related concerns. It will also ensure that if a case is necessary, all supporting documentation is available. This should not be used on its own as justification for creating a TIPS case. Cause The root cause will vary depending on the complaint. The goal of this document is to provide diagnostic checks and procedures that may help resolve customer complaints without opening a TIPS case. Remedy Before opening a transmission-related TIPS case, the following steps must be performed to ensure all relevant data has been collected and possible remedies (when applicable) have been performed. Please Note: At minimum, the documents below must be collected before proceeding to ensure the data in its original state when the vehicle arrived is captured. - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - Initial EEPROM data (.txt format) - IPR Result (if applicable. See LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool) - Transmission Heath Page If the vehicle has previously been repaired for the same concern, note the date, mileage, and TIPS case or RO number, along with a brief description of the prior work performed. IPR Guidance: The IPR recommended repair should be completed prior to following any steps in this LI and prior to case creation. IPR repairs do not require additional warranty approvals or a TIPS case to validate/confirm the results. To ensure efficient case handling, please avoid opening TIPS cases for this reason. For further information regarding IPR please see the following documents: LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool Oil Pan Condition Evaluation: In some situations, IPR will advise checking the oil pan condition and determining a repair based on the evaluation. Example photos in Xentry can be found in two ways: • Use the blue hyperlink in the IPR result, and it will take you to the Condition check of transmission oil • Navigate to Xentry Bluebook > Help for control unit > Condition check of transmission oil If a different repair that what is recommended by IPR is performed, attaching photo documentation of the complaint vehicle oil pan and the IPR example to the claim is required. Reproducing the Concern: Proper evaluation of transmission concerns generally requires the condition to be reproducible. It is recommended to compare the vehicle to a similar model, if available, to help determine whether the shift behavior is characteristic of the drivetrain or uncharacteristic for the vehicle. If the concern cannot be duplicated: • A test drive with the customer may assist in understanding and reproducing the complaint. • The vehicle shift quality should be compared to a known-good vehicle with identical drivetrain and model year. • Check Shift Quality History (VGS Control Unit > Adaptations > Shift Quality History) Shift Quality History will show the last 5 noticeable harsh shifts and some of the parameters in which it occurred. You can use this to attempt recreation of the operating conditions and increase likelihood of reproducing the complaint. Complaint A: Shift Quality Note: Certain AMG variants may exhibit more firm and noticeable shift behavior as a normal characteristic. Refer to LI27.60‑P‑075147 for additional information. 1. Perform Valve flushing procedure 2. Perform 5 Torque Converter adaptions in a row - Allow the vehicle to warm up naturally, DO NOT power brake as it will increase the temperature in the torque converter. - After the 5th adaptation, collect a screen shot showing all 5 on one page 3. Perform a standstill adaption - collect a screen shot Recheck vehicle operation. If the concern has not improved, driving adaptations should be performed to target specific gear shifts.
LI27.00-P-080840
Service Bulletin/Repair Instructions
Complaint Mercedes-Benz USA is currently experiencing limited availability of transmission fluid specification ATF 236.17 due to a global supply constraint. 236.17 ATF 1L and 5L (PNs: A002989060312 and A002989060313) bottles are out of stock or in limited supply at Zep. This LI has been created with the following intention: - Provide dealers with additional workshop-focused guidance regarding the current ATF 236.17 supply constraint and the planned introduction of ATF 236.18. - Supplement existing communications and address common workshop questions related to maintenance, repairs, and fluid applicability. - Provide technical clarification and practical workshop guidance during the temporary supply constraint period. Dealers should continue to reference the latest News Channel Updates (NCUs) for the most current information regarding availability, ordering processes, supply status, and other related updates. Cause Damage to the Shell production facility has resulted in 236.17 oil supply being reduced to 50% of normal output until the end of 2026. Remedy Please first check Latest NCU updates for latest detailed information. Please continue placing orders through Paragon as normal. Supply is expected to remain reduced and allocation measures are currently in place. We ask for your patience through this restricted supply period. Most orders will be filled in the order in which they were received, as supply is replenished. Those dealers with zero inventory, and pending orders, will receive priority. We expect supply to be stabilized in September 2026. Approved Fluids: Only use transmission fluid from the approved list found on the Mercedes-Benz Operating Fluids website. Non-approved fluid will result in mechanical damage to the transmission and must be avoided. https://operatingfluids.mercedes-benz.com/sheet/236.17 Approved fluids can be claimed as follows if there is no Mercedes-Benz part number: Part # ATFSUB1L - TRANSMISSION FLUID 1 LITER ATFSUB5L - TRANSMISSION FLUID 5 LITER Dealerships with Zero Inventory AND Grounded Vehicles: If a vehicle is currently grounded for repair at your dealer due to no 236.17 inventory, we may be able to expedite your order. Please open a StarSupport ticket including the following information: (Parts Related Inquiry>National Accounts>Zep) • LI document number • Short explanation of repair needed for grounded vehicle • Current days down of RO Maintenance and Service Interval Guidance Published maintenance intervals remain unchanged. Vehicles should continue to be maintained in accordance with the applicable maintenance schedule. This LI does not revise or extend any published maintenance interval requirements. If all required parts and materials are not available prior to scheduling or beginning a transmission service, dealers should consider postponing routine preventative transmission maintenance until the necessary parts become available. For vehicles that have not yet reached the applicable maintenance interval and do not exhibit transmission-related concerns, there is no need to recommend preventative transmission services prior to the scheduled maintenance interval. When evaluating whether routine transmission maintenance can be deferred until parts become available, dealers should consider: • Overall vehicle condition • Vehicle usage and operating conditions • Presence of transmission-related symptoms or customer complaints • Customer expectations and vehicle operating requirements • Availability of required parts and materials Introduction of New Fluid Specification 236.18 Mercedes-Benz is currently preparing the introduction of ATF 236.18 as an additional approved transmission fluid solution for applicable NAG3 transmissions. At the time of publication of this LI, ATF 236.18 is not yet available for dealer ordering or workshop use in the U.S. market. See attachment for further details.
EW - DMTL
Warranty Program/Extension
This NCU replaces the prior NCU issued on May 15, 2025, and contains additional MY 2023 and MY 2024 vehicles which are highlighted below. In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (“MY”) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: •Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (‘MIL’).
Emissions - 2024100016
Emissions
Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz, has determined that on certain MY 2019-2021 C-Class, G-Class, GLC, GT, S-Class (205, 463, 253, 190 & 222 platforms) vehicles, the engine control unit software does not correspond to current production specifications. It is therefore possible that on-board diagnostics and/or exhaust gas emissions requirements may not be fulfilled.
LI35.30-P-058566
Service Bulletin/Repair Instructions
Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).
LI33.20-P-078406
Service Bulletin/Repair Instructions
Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
PSL-NCU Return Parts 6/19
Other
Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 9, 2026. After July 9th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.
LI82.85-P-080507
Service Bulletin/Repair Instructions
Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"
PSL-NCU Return Parts 5/22
Other
Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, June 11, 2026. After June 11th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.
LI82.30-P-059239
Service Bulletin/Repair Instructions
Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).
PSL-NCU Return Parts 5/15
Other
The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, June 4, 2026. After June 4th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.
LI20.10-P-072886
Service Bulletin/Repair Instructions
Complaint CEL ON with DTC P012800 "The Coolant Temperature is Below the Specified Temperature" active and stored in the ME (N3/10). There are no drivability concerns related to the complaint. Cause Root cause varies Remedy Prior to performing any repairs for this complaint: With a cold engine, pressurize the high temp coolant circuit and while it's under pressure, release the cap on the low temp coolant circuit and check if the pressure drops right away or not. If the pressure drops, the lower hoses are swapped. Correct this, fill, bleed and test drive the vehicle. If the complaint returns, then continue with the steps below. IMPORTANT: Use VMI to check for emission extended warranty – Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) If the vehicle is covered under an emission extended warranty, Please perform steps outlined in the NCU for repairs. If vehicle is not covered under an emission extended warranty, then proceed as follows: Check for available software updates to the ME (N3/10). If updated software is available, perform the update, clear the DTC and the perform each of the "WARM START" and "COLD START" test drives listed below twice. If the code does not re-appear then release the vehicle If there is no new software available OR the DTC returns after the test drives then perform the following steps: • Drain the coolant through a fine mesh sieve and check for signs of debris. Additionally, inspect the coolant reservoir for debris. If any debris is found, flush the system several times to clear as much of the debris as possible • Replace the thermostat and bleed the system as outlined in AR20.00-P-1142-04A, evacuate the system for 20-30 minutes instead of the 5 minutes specified in step 22 • NOTE: Please use all the tools specified in the AR document • NOTE: There are two valid thermostats to choose from in the parts section of this LI. Please verify which PN is applicable for the vehicle being worked on via XENTRY Parts Information • After bleeding the system clear the DTC and perform each of the "WARM START" and "COLD START" test drives listed below twice. If the DTC does not reappear after the tests, release the vehicle If there is no new software available, the thermostat has already been replaced, and the DTC returns open a TIPS case and attach the following documents: • Initial quick test • ME (N3/10) control unit log • The results of an R48 test from a “yes” response and from a “no” response WARM START · Begin with the engine coolant temperature at approximately 50 degrees C · Activate the AC system, if defrost is not in use open the windows · Drive the car normally until a coolant temperature of 75 degrees C is achieved · Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) · Let off the accelerator pedal and let the car coast for ~10 seconds · Continue to drive the car normally COLD START · Drive for ~7 miles (normal driving) · Shut off the engine in a parking lot (or similar), wait 30 seconds, then restart and continue driving · Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) · Let off the accelerator pedal and let the car coast for ~10 seconds · Continue to drive the car normally
LI82.10-P-078301
Service Bulletin/Repair Instructions
Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304
LI72.40-P-071889
Service Bulletin/Repair Instructions
Complaint When closing the door, the side window may remain slightly open (short stroke position). Automatic window raising function of side window inoperative. NOTE: Window is fully operational while holding the switch Cause Software in door control unit (N69/x). Starting the engine at the same time as the door is closing (short stroke closure of window lifter) may result in a denormalization of the window lifter system. Remedy Update the software in the affected door control unit (N69/x). • This requires the door control unit (N69/x) to be commissioned. • (Path: XENTRY Scope; Control units view; DCU-XX (N69/x); Adaptations; Commissioning) Availability of the repair software in the field organization: • Since 10.10.2020 for model series 238, 257, 217 (FACELIFT) and A/C205 (FACELIFT) • Since 12.04.2021 for model series 118
NCU - 2024100016
Emissions
Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz, has determined that on certain MY 2019-2021 G-Class, S-Class and GT (463, 222 & 190 platforms) vehicles, the engine control unit software does not correspond to current production specifications. It is therefore possible that onboard diagnostics and/or exhaust gas emissions requirements may not be fulfilled. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will perform the ECU software update.
LI82.10-P-078307
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
LI82.10-P-078896
Service Bulletin/Repair Instructions
Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. **NOTE - As of Sept 2025 the pressure testing tool is not finalized and may require modifications to fit properly. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.
LI27.19-P-080219
Service Bulletin/Repair Instructions
Complaint Check engine light on with the following fault is current in the VGS Control Unit: P084300 Oil pressure sensor 'A' has a short circuit to positive stored in VGS control unit. Cause Electrical failure of oil pressure sensor integrated into VGS Control Unit Remedy Intelligent Predictive Repair (IPR) recognizes this fault pattern and will provide the necessary repair suggestion. 1. Perform IPR and follow the recommended procedures 2. Replace complete EHS valve body, fill to near max fluid level, & complete initial start-up - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement.
LI27.10-P-075869
Service Bulletin/Repair Instructions
Complaint Only vehicles with a variable transfer case are affected. This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?
LI83.30-P-079850
Service Bulletin/Repair Instructions
Complaint Customer states the AC either does not cool/has poor performance or heat is insufficient. Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern • Confirm the issue reported by the customer. Compare to Like Vehicle • Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players • Identify the diagnostic strategy and involved components/systems. Testing • Perform relevant diagnostic tests. Refrigerant Quantity • Record the amount of refrigerant recovered and compare it to the specified value (if applicable). • Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings • High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) • PPM of any leaks found. XENTRY Printouts • Climate control AVs. • HV compressor AVs (for heat and AC systems). Thermometer Readings • Left and right dash vents. • Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions • Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings • High and Low pressure readings before and after repairs. Thermometer Readings • Left and right dash vents before and after. • Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation • Complaint Analysis, Game/Players, and Testing Steps. • Include expected results and technical justification for the diagnosis. • Avoid listing R/I steps—focus on diagnostic reasoning and root cause. • All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)
LI05.20-P-080192
Service Bulletin/Repair Instructions
Complaint Customer states check engine light on in the dash. Vehicle has one or more DTC's Present P164B00, P164B09, P2B4400, P005A07, P005C07, P005A09, P005C09, P003C07, P2B5007, P003C09, P2B5009, P34C200, P34C109, P34C800, P34BE00, P34BD09 Cause Software and Hardware Remedy 1. Check for available Software updates for the Engine Control Unit ME N3/10. Perform update if available. 2. Check part numbers on ALL CAMTRONIC actuators to ensure latest part numbers are installed. 3. A177 982 03 03 and A177 982 17 00 should be replaced by A177 982 19 00 4. A177 982 02 03 and A177 982 16 00 should be replaced by A177 982 18 00 5. Remove engine cover and check for heat damage on the engine cover and wiring harness in the area above the engine compartment bulkhead and near the windshield. 6. In the event of wiring harness damage please open a TIPS case with photos of the harness and include a Lambda Line Graph Test for evaluation.
LI54.65-P-066284
Service Bulletin/Repair Instructions
Complaint The flap of the reversing camera opens and closes by itself during forward travel several times during the trip. No camera image is displayed in the head unit. The reversing camera or the 360° system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: • Opening the camera cover for a maximum of 5 cumulative minutes. • If the vehicle speed is < 35 km/h (<22 MPH). • The steering wheel angle is < 10°. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: • Driving forward (typically less than 1 minute). • Vehicle speed is < 35 km/h (<22 MPH). • The steering wheel angle is < 10°. • During daylight. • Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.
LI27.35-P-079971
Service Bulletin/Repair Instructions
Complaint Possible complaints about shift quality, issues with learning the park lock, and slipping/rinse entries in the EEPROM or Transmission Health system following the replacement of the below components: - The electrohydraulic control unit (EHS valve body) in transmission 725.0/725.1 - The repair kit for the control unit (VGS) in transmission 725.0 Cause Missing, incorrectly installed, or damaged guide tubes on the EHS valve body. Remedy Check for the correct installation of the guide tubes (refer to attachments under “Cause”), correct installation if necessary. Parts Catalog References: NAG3M 725.1 AND NAG3C 725.0 (AMG only): Part numbers 100, 120, 150, 160 NAG3C 725.0 (Non AMG): Part numbers 280, 290, 330, 340 NOTE: If any of these guide tubes are not installed and the vehicle is driven, it will create several rinse and slipping events in the EEPROM data. These values caused by incorrect installation need to be erased to prevent future misdiagnosis. Submit a TIPS case to the Powertrain inbox with the following to receive the necessary reset password: - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - IPR Result - Initial EEPROM data (before repairs) - Latest EEPROM data - Photo of oil level ultrasonic measurement next to XENTRY specifications Please provide detail regarding the reasoning for the initial replacement in your workshop findings and measures performed. (This topic was covered in the July 2022 and July 2024 Passenger Car Tech Topics)
LI54.10-P-071499
Service Bulletin/Repair Instructions
Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. • Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. • Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".
LI46.15-P-063353
Service Bulletin/Repair Instructions
Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function), noise (breakaway noise) when leaving the limit stops of the height adjustment. Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Driver seat control unit software 2. Steering column height adjustment transmission Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Perform software update of driver's seat control unit 2. Replace repair kit for steering column height adjustment Procedure 1: Perform software update of driver seat control unit. ALL models except 205/253/293/222/217/231/463/213/238/257/290 up to special equipment code 801. • Move out the fore/aft adjustment to the end position. • Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward • After releasing the jam, perform a software update of the driver's seat control unit If procedure 1 is not effective, there is no new software available for the driver seat control unit, or the chassis is not listed above (167, 223, 294, 206, 294, 295, 296, 297,232,214,254) then use procedure 2. Procedure 2: Replace repair kit for steering column height adjustment. • Move out the fore/aft adjustment to the end position. • Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward • Remove footwell trim on driver's side. • Determine type version of height adjustment in XENTRY Parts Information and order appropriate replacement part (refer to attachment). 1. Version A: A 231 460 77 00 2. Version B: A 205 460 38 03 • Remove steering column. • Remove height adjustment (adjustment repair kit). • Install repair kit (adjustment repair kit) (observe tightening torque for screws in attachment). • Install steering column. • If possible, flash driver seat control unit to latest software release or code SCN again. • Commission driver seat control unit (normalization of limit stops is deleted and learning process repeated).
CL - 05012025
Other
In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage detection (“DMTL”) on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership.
LI82.85-P-079088
Service Bulletin/Repair Instructions
Complaint The following most common complaints may be observed: • Brief connectivity interruptions when using Apple CarPlay over Wi-Fi • Audio cuts out • Device not recognized • No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicle’s head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference External Sources: • Passing under toll bridges, driving near airports, or areas with heavy electronic interference (e.g., as described in LI82.85-P-076157) can cause connection drops. Cellular Networks: • Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: • Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Issues Head Unit Software/Hardware: • Outdated firmware, bugs, or hardware faults in the vehicle’s head unit can prevent a stable connection. iPhone Software/Hardware: • Similar issues in the iPhone, including buggy iOS updates or hardware problems, may affect performance. Reset or Reboot: • Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings Wired Connections: • Faulty Cable: A damaged or poor-quality USB cable can cause intermittent or total loss of connection. • USB Port Issues: Dust, debris, or physical damage in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: • Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: • Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. • Vehicle’s Electrical System: Unstable power delivery from the car’s battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration Phone Settings: • Incorrect or conflicting settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. • Third-Party Apps/Profiles: • Installed apps or configuration profiles may conflict with CarPlay’s operation. • Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: • Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: • Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors Heat & Overheating: • If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: • Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy Guided Diagnostic Path for Apple CarPlay Connection Issues Please follow the steps below to systematically diagnose and resolve CarPlay concerns: Update Devices: • Ensure the iPhone is updated to the latest available iOS version. • Ensure the vehicle’s head unit is updated to the latest software version available. Isolate the Issue: • Check whether the symptom persists with another iPhone running the latest iOS version. • Test both wireless and wired CarPlay connections: • Does the issue only occur with wireless CarPlay?
LI82.85-P-079271
Service Bulletin/Repair Instructions
Complaint After a software update of HERMES communication module N112/9 has been performed on a gray import vehicle, the message "SOS - Service not activated" is displayed in the instrument cluster. Cause The message "SOS - Service not activated" tells the customer that "over-the-air" registration of the vehicle with the Mercedes Intelligent Cloud is not possible. On a gray import vehicle, this is due to the fact that the SIM card installed in the HERMES communications module cannot dial into the mobile phone network in the importing country. Remedy The only way of avoiding the message in the instrument cluster is to deactivate the HERMES module using the 09o deactivation process after obtaining the customer's consent. After deactivation, the HERMES control unit (N112/9) has the operating status "Inoperative". The message "SOS not ready" appears in the audio/COMAND display (A40/8) and may also appear in the instrument cluster. This display message tells the customer that the emergency call function is not available. In addition, the workshop must attach a label (2 x part number A9078172900 required) to the cover of the emergency call button in the overhead control panel and to the emergency call button itself. Replacing the hardware of the HERMES communication module is not effective.
LI33.30-P-056665
Service Bulletin/Repair Instructions
Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts
EW - Tank Leakage
Warranty Program/Extension
In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (“MY”) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: • Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (‘MIL’).
LI54.30-P-075652
Service Bulletin/Repair Instructions
Complaint The last settings for the Augmented Reality Head-up Display (AR HUD) may not always be saved and the settings are reset to the default state. Cause Instrument Cluster control unit (N133/1) software Remedy Update the Instrument Cluster control unit (N133/1) software.
LI54.71-P-079104
Service Bulletin/Repair Instructions
Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. Cause Under Investigation Remedy Under investigation. One option is to turn off Traffic Sign Assist until the investigation is completed. Once completed this LI will be updated. No TIPS case is necessary. Do not replace parts.
NCU - 2025030015
Service Campaign
Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the SCN coding of the electronic ignition control unit does not correspond to the latest production specifications. As a result, a red battery warning message could inadvertently display on the instrument cluster. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will perform an SCN coding of the electronic ignition control unit.
LI27.35-P-079039
Service Bulletin/Repair Instructions
Complaint A clicking/ticking/taping noise from underneath the vehicle with engine off during ECO stop event or after parking See video for example Cause Noise originates within the transmission valvebody Remedy Take a video from underneath vehicle recording the noise Pull EEPROM data, Inital Quick Test, and Control Unit Log Please open a TIPs case providing all data to assess next steps.
OTA - 5497748
Over The Air
Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.
LI82.70-P-077433
Service Bulletin/Repair Instructions
Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
CL - Engine Thermostat
Other
On certain Model Year 2019 - 2023 C / E / G / GLC / GLE / GLS / GT/ S / SL - Class vehicles fitted with an eight-cylinder engine, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp ('MIL') to illuminate.
EW - Engine Thermostat
Warranty Program/Extension
This NCU supersedes the prior NCUs issued on December 1, 2023 and February 06, 2024 and includes additional MY 2019 AMG G63 vehicles. In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the engine thermostat (including software update) installed in certain Model Year (“MY”) vehicles (with engines M176, M177, M178) listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first), due to the following condition In the affected vehicles, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp (‘MIL’) to illuminate.
CL - 2024110005
Other
Please visit an authorized Mercedes-Benz dealer where they will check the wiring of the lens hood of the multifunction camera and replace it if necessary. This repair is free of charge. Please schedule an appointment by contacting the MBUSA Customer Care Center at 1-800-367-6372, or locate your nearest dealer using the QR code and “Find a Dealer” section on the website.
LI88.60-P-072093
Service Bulletin/Repair Instructions
Complaint Fuel door may require several attempts to open. Please note that if the complaint "Fuel filler flap not opening" occurs, it is important to check the fuel filler flap before replacing the central locking actuator. For gasoline hybrid vehicles where the fuel filler flap fails to open or does so but slowly, observe the document "Fuel filler flap fails to open or does so but slowly on plug-in HYBRID gasoline vehicles"! Cause Central locking actuator may have an electrical fault and may not open. Remedy 1. Car locked: To rule out incorrect operation, operate the fuel filler flap in the area shown in Fig. 1 and listen out for the clicking noise of the microswitch in the central locking actuator. If no clicking can be heard, continue with point 4. 2. Car unlocked: Press area on flap to start the microswitch clicking. Flap opens - show the customer the area to press. 3. Car unlocked: Flap cannot be opened regardless of which area you press. Open the flap by operating the emergency release for the CL actuator (through trunk, fender gap cover, etc, depending on specific vehicle) 4. Central locking actuator pressed directly, no clicking of microswitch, no electrical release of central locking actuator => Clicking of microswitch, electrical release of central locking actuator => Tank filler recess/charging recess not OK; report results via a TIPS case to B/C/E Inbox. 5. Replace central locking actuator; check function of new part before installing it: Do not dispose of damaged part. New central locking actuator does not release: More detailed examination of connector coupling, wiring harness, electrics required.
LI42.10-P-063502
Service Bulletin/Repair Instructions
Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it and then continue with1b. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: NOTE: If brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise.
OTA - 24P5497813
Over The Air
Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
LI27.19-P-072588
Service Bulletin/Repair Instructions
Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
LI82.35-P-078467
Service Bulletin/Repair Instructions
Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
NCU - 2022070004
Service Campaign
Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (“MY”) 2018 - 2024 E-Class, S-Class & AMG GT (213, 217, 222, 223 and 290 platforms) vehicles, the low pressure fuel line does not meet current production specifications. Therefore, it is possible that accelerated aging in the area of connection could occur, resulting in a leak. A risk of fire can be ruled out. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will replace the braided hose of low-pressure fuel line and install a heat shield over the new braided hose.
LI54.71-P-078498
Service Bulletin/Repair Instructions
Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
LI82.10-P-078069
Service Bulletin/Repair Instructions
Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
LI27.00-P-073124
Service Bulletin/Repair Instructions
Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: ·NAG3 Classic (automatic transmission 725.0) ·NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) ·NAG3 - AMG 63 ·NAG3 - Hybrid
LI07.61-P-070707
Service Bulletin/Repair Instructions
The customer complains of a check engine light (CEL) on. May also complain of the engine running roughly and/or a loss of power. Multiple Causes Remedy Please see the document "Remedy Instructions" in attachments. For MY19+ G63 there may be an alternate solution available. Please reference LI07.61-P-076755 before performing the steps in this LI.
NCU - 2024040008
Service Campaign
Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-23 C-Class and S-Class vehicles (206, 223 platform), the software for the ISA control unit may not correspond with the latest series production configuration. The possibility exists that the function of the ISA may not be restricted with an active Malfunction Indicator Lamp. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the ISA control unit software in the affected vehicles.
OTA - 20240503
Over The Air
Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, CLA, EQB, EQE, EQS, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (118, 167, 192, 206, 223, 232, 243, 247, 254, 290, 294, 295, 296 and 297 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for a better entertainment experience. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
OTA - 24240302
Service Bulletin/Repair Instructions
This is to notify you of the Service Campaign OTA update for the MBUX control unit software in 14,559 Model Year (MY) 21-23 C-Class, S-Class, SL, EQS (206, 223, 232, 297 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-23 C-Class, S-Class, SL, and EQS vehicles (206, 223, 232, 297 platform), the MBUX System software does not correspond with the latest series production configuration. The MBUX control unit will receive an OTA update that includes functional improvements and new features such as: Dolby Atmosî, video streaming, personalized images on the front passenger display, and additional commands for the MBUX Voice Assistant. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâÂÂs vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
LI00.20-P-077615
Service Bulletin/Repair Instructions
The following symptoms may be present in the instrument cluster: 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. Routine change in software in instrument cluster N133/1. Vehicle handover has not taken place. First manually commission the already installed instrument cluster control unit N133/1 and then perform the special procedure to re-initialize ASSYST data in powertrain control unit N127. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicleâÂÂs warranty in any way.
OTA-24240201
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âÃÂÃÂMBAGâÃÂÃÂ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâÃÂÃÂs vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
LI46.10-P-077313
Service Bulletin/Repair Instructions
The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgeräusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
LI46.10-P-077314
Service Bulletin/Repair Instructions
Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
LI68.10-P-077315
Service Bulletin/Repair Instructions
Front armrest cap (butterfly compartment) only opens when pressed strongly. Unfavorable tolerances Place two pieces of felt (12mmx12mm) on the trigger mechanism as seen in the attached picture. This will reduce the distance between the pushbutton switch and the trigger mechanism.
NCU-OTAcommNoMMC
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âÂÂMBAGâÂÂ), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâÂÂs vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
CL-AirSuspension
Service Bulletin/Repair Instructions
On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youâre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Air Suspension System Software on certain Model Year 2021-2023 S-Class and EQS vehicles. This update will optimize your vehicleâs Air Suspension System and improve its ground clearance, especially during parking. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active âMercedes me connectâ subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
CL-CommMod
Service Bulletin/Repair Instructions
Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youâÂÂre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active âÂÂMercedes me connectâ subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
NCU-2023120012
Service Bulletin/Repair Instructions
Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has released a software update for certain MY 2021 S-Class (223 platform) vehicles that allows for future remote software updates on additional control units. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the Communication Module software.
NCU-2023120013
Service Bulletin/Repair Instructions
Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has released a software update for certain MY 2021 S-Class (223 platform) vehicles that includes functional improvements for route guidance, Apple Carplay, and Android Auto. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the MBUX System Software.
LI82.62-P-077311
Service Bulletin/Repair Instructions
No audio is output either in radio mode, or with media playback via app, Bluetooth or USB. In such cases, "Playback not active" is shown in the display. Mute line between communication module N112/2 and sound control unit N40/3. Check mute cable (violet) between control units for communication module N112/2 and sound N40/3, including plug contacts, and repair or replace as necessary. If the plug contact is deformed, it is imperative that its counterpart at the control unit is also checked.
OTA-Air Susp SW
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âÂÂMBAGâÂÂ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-23 S-Class, EQS (223, 297 platform) vehicles, the air suspension system software does not correspond with the latest series production configuration. The air suspension system will receive an OTA update to optimize the system and improve the ground clearance, especially during parking. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâÂÂs vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
OTA-Comm Mod SW
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âÂÂMBAGâÂÂ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâÂÂs vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
LI46.35-P-077076
Service Bulletin/Repair Instructions
Control unit N68 - electric power steering Fault P063544 - The electric power steering has a malfunction. There is a fault in the data memory. with fault freeze frame data "Mon_ID 320" in the "stored" status stored in the fault memory of control unit N68. No functional restrictions of the electric power steering or warning messages are visible. Faults occur in the event of a software update or when initializing the control unit for the electric power steering N68. The fault code can be ignored and the fault memory of the control unit for the electric power steering N68 can be deleted. It is not necessary to replace the electric power steering.
LI91.18-P-077075
Service Bulletin/Repair Instructions
Crease formation on genuine leather seat covers in vehicles with low mileage ⢠Objects left on the seats for extended periods of time (pressure marks). ⢠Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). ⢠Light initial creases due to vehicle handling. ⢠Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
EW-EngineThermSW
Service Bulletin/Repair Instructions
In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the engine thermostat (including software update) installed in certain Model Year ("MY") vehicles (with engines M176, M177, M178) listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first), due to the following condition: In the affected vehicles, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp ("MIL") to illuminate. Please follow the work instructions added to this NCU to remedy the issue. Please be advised that all repairs being claimed under this extended warranty must have a quick test uploaded with the following fault code information and may be audited. P012800 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 20102 - Insert, coolant thermostat o 52 - Does not operate correctly o 41 - Hard closing 20103 - Housing/cover, coolant thermostat o 73 - Electrical fault 2030T - Heating element, coolant thermostat o 53 - Insufficient effect/power o 73 - Electrical fault
OTA-InductNonMMC
Service Bulletin/Repair Instructions
Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, EQE, EQS, S-Class (206, 294/295, 296/297 and 223 platform) vehicles, the inductive charging system software does not correspond with the latest series production configuration. The inductive charging system will receive an OTA update that includes improvements for the wireless charging of the Apple iPhone 14 and subsequent generations with MagSafe. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this OTA software update.
OTA-InductiveSW
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âÂÂMBAGâÂÂ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, EQE, EQS, S-Class (206, 294/295, 296/297 and 223 platform) vehicles, the inductive charging system software does not correspond with the latest series production configuration. The inductive charging system will receive an OTA update that includes improvements for the wireless charging of the Apple iPhone 14 and subsequent generations with MagSafe. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâÂÂs vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
LI82.95-P-076991
Service Bulletin/Repair Instructions
Mercedes me connect services inoperative (me-Call, Remote Status, etc.). Mercedes me services - activation not possible. Notes: - In the quick test, no fault code and no event code is stored in the RAMSES control unit (N112/2). The SIM card may be defective. A defective SIM card can be identified as follows: With XENTRY Diagnosis, open the "ACTUAL values" menu of the RAMSES control unit and read out the values for "EUICC, ICCID, IMEI, IMSI". ACTUAL values in the event of a defect: 1. EUICC:null 2. ICCID: null 3. IMEI: null 4. IMSI: null If all the values for "EUICC, ICCID, IMEI, IMSI" = null, then it is highly likely that the SIM card inside the RAMSES control unit is defective. Recommissioning the RAMSES control unit may rectify the problem. If the problem is still present after the recommissioning, then the RAMSES control unit must be replaced. In this case, please create a TIPS case and forward it to HQ. The part is required for analysis. Information on the return delivery of the module will be communicated via TIPS case.
NCU -MBUX SW OTA
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âÂÂMBAGâÂÂ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-23 C-Class, EQS, S-Class, SL, EQE, GLC (206, 296, 297, 223, 232, 294, 295, 254 platform) vehicles, the head unit software will be updated remotely to MBUX 2.4. With this update, customers will benefit from many new functions and features, such as video streaming (note that the Entertainment Package Plus is required for streaming and can be purchased from the Mercedes me Store by the end of 2023), Dolby Atmosî, MBUX Voice Assistant (NewsFlash & Tourguide), a personal decorative image on the front passenger display, and more. Please see NCU issued on September 5th, 2023 from Product Management and Digital House team âÂÂAdditional New Connected Features Coming SoonâÂÂ. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâÂÂs vehicle free of charge without an additional workshop visit via the data link of the communication module. No customer letter will be mailed for this software update.
LI82.85-P-076800
Service Bulletin/Repair Instructions
The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
LI83.30-P-076965
Service Bulletin/Repair Instructions
Following a software update of the head unit to FUP3 variant 316.5 or higher, the "Residual heat" button is no longer displayed in the air conditioning system operating menu. A26/17 head unit MBUX software There is currently no remedy available. Replacing the hardware will not remedy the problem. A software update is intended with the FUP4 software E444.x (planned release for Q4/23)
NCU-23P5497107
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âMBAGâ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2021 S-Class (223 platform) vehicles, the software for the communication module does not correspond to the latest series production configuration. The communication module software will be updated to enable remote software updates on other control units in the future. Further contributions to product improvement and increases in robustness will also be implemented with this software update. The update is free of charge and will be carried out in the background. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâs vehicle free of charge without an additional workshop visit via the data link of the communication module. No customer letter will be mailed for this software update.
NCU-23P5497108
Service Bulletin/Repair Instructions
Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain MY 2021 S-Class (223 platform) vehicles, the software for the communication module does not correspond to the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will update the communication module in order to be able to perform remote software updates on further control units in the future. Further contributions to product improvement and increases in robustness will also be implemented with this software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. Customer letters were mailed August 11, 2023.
Ll54.10-P-076896
Service Bulletin/Repair Instructions
12V message in IC when starting the vehicle. SW updates need to be performed. Follow the guided test for FC U116000 in N73/3*1 EIS CU. Perform the SW checks and updates. Fully charge both 12V and 48V batteries. After, perform a few drive/park cycles with at least 1 overnight park cycle. If the 12V message is no longer present, release the vehicle.
LI82.85-P-076866
Service Bulletin/Repair Instructions
Complaint On vehicles with a low mileage, it may be the case that the displays in the rear passenger compartment do not start up. The Samsung tablet also remains stuck on the disclaimer. The Rear Seat Entertainment Package is nonfunctional and cannot be started or operated. Transport mode was unable to be completely deactivated. The rear seat unit is still in transport mode. Perform activation and subsequently deactivate the transport mode. Update the A26/17 - MBUX multimedia system (Head unit) to current software release.
NCU-HU SW Update
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âMBAGâ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customerâs vehicle. The OTA may be validated as successful on the customerâs Mercedes Me connect app under âOver-the-Air Vehicle Updatesâ as âUpdate for the communication moduleâ. If the OTA is successful it will show a green âinstalledâ and date of installation in the Over-the-Air update section.
LI82.70-P-076832
Service Bulletin/Repair Instructions
Phone call log is not shown in the MBUX display. If the telephone connects with the head unit again, the call log may not be sent. Current software release for the A26/17 - MBUX multimedia system (Head unit) Currently there is no remedy available. Replacing the hardware will not resolve the symptom. ⢠New software for the A26/17 - MBUX multimedia system (Head unit) will be made available with software version E444.x (scheduled for Q4/2023)
LI82.85-P-074541
Service Bulletin/Repair Instructions
With the adaptations from modification year 802 to modification year 803, the illumination of the multimedia connection units has also been converted from white to blue. The conversion in the production process could result in a different assignment (sometimes white instead of blue or vice versa). Conversion in the production process If a customer reports the different assignment (sometimes white instead of blue or vice versa). please open a TIPS case
LI72.10-P-076701
Service Bulletin/Repair Instructions
Flush door handle needs to be pulled on with increased force in order to open the door manually. Turning angle sensor lever is broken. Replace the bearing bracket of the flush door handle.
NCU - HU Update
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âMBAGâ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2021-2024 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the head unit software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customerâs vehicle. The OTA may be validated as successful on the customerâs Mercedes Me connect app under âOver-the-Air Vehicle Updatesâ as either âSoftware Update MBUX 2.4â or âSoftware Update Hermes 1.5 E522.8â. If the OTA is successful it will show a green âinstalledâ and date of installation in the Over-the-Air update section.
LI00.20-P-075495
Service Bulletin/Repair Instructions
Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. Cause Routine change in software in instrument cluster N133/1. Vehicle handover has not taken place. Remedy Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in powertrain control unit N127.
NCU-2023040017
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âMBAGâ), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2022-2023 C-Class, EQS and S-Class (206, 297 and 223 platform) vehicles, the driving assistance system control unit software does not meet current specifications. In the presence of uniquely shaped civil superstructures that parallel the roadway at a height of~26-33 feet (e.g. large overhanging bridge abutments, etc.), the vehicle may initiate brake applications during operation. In such cases, the driver remains in control of the vehicle and can override the system at any time. What Weâre Doing An authorized Mercedes-Benz dealer will update the driving assistance system control unit software.
NCU-OTA051923
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âMBAGâ), the manufacturer of Mercedes-Benz, has determined that on certain MY 2021-2023 EQE, EQS, EQS SUV, and S-Class (223, 295, 296, and 297 platform) vehicles, the software of the sound system does not correspond with the latest series production configuration. The software update serves as the necessary preparation for additional functionalities that will be included in the future to improve and expand the sound system of the vehicles. The update is free of charge and will be carried out in the background. The installation will take approximately 3 minutes, the system can be used without restrictions during this period. The new software will be active during the next driving cycle. What Weâre Doing MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customerâs vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
LI91.60-P-076303
Service Bulletin/Repair Instructions
Complaint Electrical fault on rear airbag/window airbag. SRS indicator light on in instrument cluster. Cause Contact problems that may create a short circuit between the pins or to the vehicle ground Remedy Connect and disconnect the affected airbag five times Then the squib must be carefully blown out with dry compressed air.
LI82.62-P-076176
Service Bulletin/Repair Instructions
Complaint Static noises from speakers while driving (see video labeled example of noise). Static noise is no longer present after opening a window (slightly) or when sliding sunroof is in tilt position. Cause A total of 4 sensors are installed at the axle housings for the "Active driving noise compensation" function. These record driving noise and transfer them to control unit N156/1 - Active driving sound compensation (ASX7) as electrical pulses. The angle bracket of the sensor may come into contact with the longitudinal member of the body. As a result, unintended vibration may be transferred via the bracket to the sensor. The control unit interprets this as driving noise and tries to compensate, causing noise in the speakers. Remedy Check assembly of sensors particularly, the brackets, and ensure that they do not come into contact with the body. If this does not remedy the problem, please create a TIPS case. NOTE: There may be no mechanical forces on the sensor as there may be a danger of damage.
LI72.10-P-075291
Service Bulletin/Repair Instructions
Complaint The surface-flush door handle sometimes does not retract when the vehicle is locked. It is only after repeated locking operation that the problematic door handle retracts. Cause Motor fault detection (FC B185E96 or B185D96) is triggered in the bearing bracket electronics of the surface-flush door handle (A17/x) during the retracting movement and an adjustment for this cycle is prevented. Remedy Replace bearing bracket of surface-flush door handle on problematic door.
LI82.85-P-075094
Service Bulletin/Repair Instructions
Complaint Traffic Light View is intermittently inoperable after updating the MBUX Multimedia System (A26/17) to E316.5. Cause Previously available MBUX software release. Remedy A new software remedy is currently available. Please update the head unit software to version E329.5 or newer.
LI82.20-P-075747
Service Bulletin/Repair Instructions
Complaint The "Ambient Light Warning Assistance Inoperative" warning message is displayed in the instrument cluster and the light-emitting diode strips are not working. This message is set by the active ambient lighting control unit (N162/1), when a light-emitting diode strip is missing or where a fault is detected in the light-emitting diode strip. Cause The following causes are possible: 1. Rework in active ambient lighting area. The ambient lighting is switched on and the connectors are disconnected from the wiring harness.NO fault code is stored. 2. Fault code 123X87 (communication error) is stored in the active ambient lighting control unit (N162/1) and an lightemitting diode strip (E34/1-6) is displayed in the quick test with ! (exclamation mark).. 3. Fault code 186X00 (malfunction) stored in the light-emitting diode strips (E34/1-6). 4. Fault code 186x98 (overtemperature) stored in light-emitting diode strips (E34/1-6). 5. There are no fault codes stored in the active ambient lighting control unit (N162/1) and in the light-emitting diode strips (E34/1-6). Remedy 1. Lock and unlock vehicle to reset the active ambient lighting control unit (N162/1). IMPORTANT: When locking, the visual locking verification signal must be visible. Make sure that all the doors are shut. After locking, wait until the instrument cluster switches to OFF, then press unlock. 2. Run guided test as per XENTRY Diagnosis (check electric lines and connectors).
LI82.85-P-075699
Service Bulletin/Repair Instructions
Complaint Customer states that they are unable to actuate the rear-door roller sunblinds via the MBUX settings. Note: The roller sunblinds can still be actuated by the switch on the respective door panel Cause Root cause varies depending on model year Remedy For model year 22 and newer: ⢠Perform software updates of the Rear Door Control Units (N69/3 and N69/4) For model year 21: ⢠There is no technical resolution
LI54.71-P-075704
Service Bulletin/Repair Instructions
Complaint Message in IC: "Active Brake Assist function restricted". "Active Emergency Stop Assist inoperative" "Active Lane Keeping Assist inoperative" "Active Blind Spot Assist inoperative" Note: The problem can occur after a software update of control unit N62/4 - Driver assistance system A quick test may not show any relevant fault codes related to the IC messages. Cause In rare cases, it may be that no automatic SCN coding was performed after control unit N62/4- driver assistance system was programmed. Remedy Perform SCN coding of N62/4 Driver assistance system
NCU-2022070017
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âMBAGâ), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (âMYâ) 2021 S-Class (223 platform) vehicles, the software for the driving assistance system control unit may not correspond to the current production specification. This may result in faulty long-range radar-based warnings occurring. What Weâre Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the driving assistance control unit software
NCU-2022090003
Service Bulletin/Repair Instructions
Mercedes-Benz AG (âMBAGâ), the manufacturer of Mercedes-Benz, has determined that on certain MY 2021 E-Class and S-Class (213 and 223 platform) vehicles, the steering wheel material does not correspond to current production specifications. Over time, the leather may detach from the steering wheel. What Weâre Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the steering wheel and the hand detection control unit, if necessary.
SC-2022070004
Service Bulletin/Repair Instructions
Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (âMYâ) 2028-2021 S-Class, S-Class Coupe/Cabriolet (217 and 222 platforms) vehicles, the low pressure fuel line does not correspond to the current series production configuration. Therefore, it is possible that accelerated aging in the area of connection could occur, resulting in a leak. A risk of fire can be ruled out. What Weâre Doing MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will replace the braided hose of low-pressure fuel line and install a heat shield over the new braided hose
SC-2022080009
Service Bulletin/Repair Instructions
Replace steering column switch module
LI7210P073487
Service Bulletin/Repair Instructions
Clattering noise when raising lowering window using the front door window
LI7210P073469
Service Bulletin/Repair Instructions
Flushmounted door handle may be sluggish when retracting.
LI8860P073470
Service Bulletin/Repair Instructions
Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
LI8220P073452
Service Bulletin/Repair Instructions
The "Ambient Light Warning Assistance Inoperative" warning message is displayed in the instrument cluster and/or the lightemitting diode strips are not working.
LI8285P072788
Service Bulletin/Repair Instructions
The rear entertainment system displays may flicker see attached.
LI8061P073358
Service Bulletin/Repair Instructions
The flushmounted door handles are retracted and do not extend electrically in response to a command from the door handle sensor in center of door handle is touched see Picture 1, A, so that the door can be opened.
LI80.61-P-072709
Service Bulletin/Repair Instructions
Hands-free Access, trunk lid opening via KG as well as 'closing and locking' via inside trunk lid button nonfunctional
P-SC-2021020005
Service Bulletin/Repair Instructions
Update Left and Right Front and Rear Door Control Unit Software
LI07.61-P-072259
Service Bulletin/Repair Instructions
Customer complains that check engine light is on. Cause and remedy under investigation