Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
M610607
Service Bulletin/Repair Instructions
MINI electrical systems have continued to develop over the past few years. As a result, the demand on the batteries has increased. Breakdowns due to an empty battery or problems in the vehicles electrical system can have various causes, most of which are not due to the battery itself. For this reason, a battery replacement will permanently eliminate the problem only in the rarest of cases. The energy diagnosis test module helps to localize these causes. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints. Without performing the energy diagnosis test plan, the root cause of a discharged battery cannot be identified. In order to properly repair the vehicle the first time, it is very important that the diagnostic test plan is performed to completion; with all results taken into consideration.
M360119
Service Bulletin/Repair Instructions
New RDC wheel electronics will be introduced with future generation MINI models. The new wheel electronics are identified as Huf Generation 5. These new wheel electronics will need to be programmed using the new tool when replaced or when depressurized (0 psi) for more than 2 minutes.
M011116
Service Bulletin/Repair Instructions
OC3 SEAT OCCUPANCY MAT - LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES: Component-Specific Limited Warranty Extension For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (MINI USA) is extending the limited warranty for the front passenger's OC3 seat occupancy mat (shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date.
M010419
Service Bulletin/Repair Instructions
CLASS ACTION SETTLEMENT: N14 HIGH-PRESSURE FUEL PUMP (HDP) SERVICE BENEFIT CLASS VEHICLES: The MINI vehicle may experience a sudden engine operational failure reduced or loss of power while driving and the malfunction indicator lamp (MIL) may be illuminated along with high-pressure fuel pumprelated faults stored in the Engine Control Module (DME). PROCEDURE Perform the corresponding diagnosis/vehicle test and run the test plans to completion as applicable.
M230108
Service Bulletin/Repair Instructions
MANUAL TRANSMISSION - STIFF DIAGONAL GEARSHIFT LEVER MOVEMENT. The customer may complain of a "stiff diagonal shift" (e.g., N-R, R-N, 2-3/3-2 or 4-5/5-4). Also, in some cases, gears cannot be selected, or the selector gear does not go into the neutral position. CAUSE 1. The deflection lever circlip of the gearshift mechanism is damaged or missing. 2. Possible corrosion at the gearshift mechanism (shift cables or transmission gearshift unit)
M170115
Service Bulletin/Repair Instructions
ENGINE CRANKS, NO START AND/OR ENGINE COOLANT TEMPERATURE FAULTS: NOTE: The engine may also exhibit the same starting behavior as in Situation1.
M650610
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM HAS MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
M010118
Service Bulletin/Repair Instructions
N18 ENGINE TURBOCHARGER: LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES
M640114
Service Bulletin/Repair Instructions
Automatic Deactivation of Recirculation Mode. The customer states the recirculation display goes out, even though the recirculation button was switched on. CAUSE The automatic recirculation air deactivation feature was introduced in July 2012. Note: If the customer dislikes this feature, it can be deactivated by using the following steps.
M010116
Service Bulletin/Repair Instructions
N18 Engine High-Pressure Fuel Pump (HDP): Limited Warranty Extension to 10 Years/120,000 Miles This Service Information bulletin supersedes SI M01 01 16 dated March 2016.. For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (MINI USA") is extending the limited warranty for the engine's High-Pressure Fuel Pump (HDP) to: z 10 years/120,000 miles as determined by the vehicle's original in-service date z Item #1: This "component-specific" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the New MINI Passenger Car Limited Warranty. z Important Note: This limited warranty extension only applies to the listed vehicles produced up to and including 2/29/2012 (Leap year). z Vehicles produced on or after 3/1/2012 are fitted with different equipment. Warning: This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release."
BMWDEC0116
Service Bulletin/Repair Instructions
Update MINI Water Pump Class Action Settlement: Herremans v. BMW of North America, LLC. MINI USA, a division of BMW of North America, LLC ("MINI USA") has entered into a nationwide settlement with the plaintiffs in the above referenced class action and the Court has granted final approval of the settlement. This DCS message provides you with the latest information about this case and the settlement. Class Allegations. The Plaintiff claimed that MINI produced and sold certain MINI Cooper Class Vehicles with defective water pumps. Class Vehicles are MINI R55, R56, R57, R58, R59, and R60 Series vehicles equipped with N12, N14, N16 or N18 engines that were sold or leased to Class Members in the US (including Puerto Rico). The Class Vehicles were produced from October 2006 through November 2012.
M011216
Service Bulletin/Repair Instructions
ENGINE MECHANICAL WATER (COOLANT) PUMP: LIMITED WARRANTY EXTENSION TO 7 YEARS/84,000 MILES. INFORMATION As part of a Class Action Suit Settlement for the vehicles listed above ("Class Vehicles"), MINI USA, a division of BMW of North America, LLC, is extending the limited warranty for the engine mechanical water pump to: z Item #1: This "component-specific" limited warranty extension applies to defects in materials or workmanship. z This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. z When it is necessary, the friction wheel is covered only when it is done in conjunction with performing an eligible and covered engine mechanical water pump repair. z This extended coverage does not apply to electric water pump. Note: This bulletin is a notice of a component-specific "limited warranty extension as part of a Class Action Settlement. This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing a problem with the water pump.
M651016
Service Bulletin/Repair Instructions
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
M010616
Service Bulletin/Repair Instructions
FOOTWELL MODULE: LIMITED WARRANTY EXTENSION TO 8 YEARS/125,000 MILES. When performing ISTA/D diagnosis and/or a programming procedure (software update) on an affected vehicle, the Footwell Module could fail. There is a compatibility issue with certain combinations vehicle software (Plant Integration ILevel) and the Footwell Module hardware installed in the vehicle.
M630116
Service Bulletin/Repair Instructions
Delay in Automatic Driving Light Switching on/off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes. Shut-off period varies based on detected situation. This is normal operational behavior.
M840114
Service Bulletin/Repair Instructions
Bluetooth Connection Failures This Service Information bulletin supersedes SI M84 01 14 dated February 2016.. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware
M090115
Service Bulletin/Repair Instructions
New programming feature: Exclusion of Infotainment Control Units from Programming.
M110815
Service Bulletin/Repair Instructions
Surface Cracks on the Water Pump Drive Pulley. During a repair, service or inspection, the drive pulley on the water pump shows signs of cracking. No part replacement is necessary unless there is another issue found that will be corrected by replacing the drive pulley.
M011014
Service Bulletin/Repair Instructions
MINI Motorer-Focused Satisfaction (MFS) Program. Based on Motorer feedback, MINI has determined that during the first three years of service, some vehicles may require specific additional service work to be performed. To address this issue, MINI USA, a division of BMW of North America, LLC ("MINI USA") is providing the following Motorer-Focused Satisfaction (MFS) Program. This program's procedures have been available to you to address specific Motorers' concerns since September 1, 2014. As part of our Motorer Pledge to deliver an incredible MINI motoring experience, for the abovereferenced MINI vehicles, we developed this program to increase our Motorers' satisfaction by helping to prevent unexpected dealer service repair visits.
M640215
Service Bulletin/Repair Instructions
The Blower Motor is Faulty. The blower motor does not operate at any fan speed. The blower motor may work intermittently with the blower fan speed operating only on FULL speed. CAUSE The blower motor is faulty and causes the blower resistor to fail.
M651015
Service Bulletin/Repair Instructions
NAV Road Map Installation Using USB Stick. The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. 32GB USB stick is necessary Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to the Attachment. 2. To install the desired NAV road map version into the vehicle, connect the USB stick into the USB connector. The connector is located: On R-Series MINI vehicles in the glove box: https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/26...10/5/2015 Page 2 of 2 On F-Series MINI vehicles at the center instrument panel area 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment M651015_Attachment.
M510113
Service Bulletin/Repair Instructions
Service Action: Replace Both Sun Visors. When opening the sun visor mirror cover, the pivot pins bind. CAUSE The spring tension is too great and weak pivot pins can break.
M650213
Service Bulletin/Repair Instructions
CHAMP2: Stored Radio Stations Deleted After Ignition Off. After ignition off, the stored radio stations (AM/FM and Satellite radio) are no longer available in: ? Menu "PRESETS" ? Preset buttons on the head unit Hardware error in the CHAMP2 head unit
N-14-05-09
Service Bulletin/Repair Instructions
MINI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. QUESTIONS AND ANSWERS FOR TIMING CHAIN OF VARIOUS MINI. *PE
M360215
Service Bulletin/Repair Instructions
Valve Stem Replacement with Wheel Electronics. Tire pressure loss after replacement of the RDC/RDCi wheel electronics. Valve stems are not being replaced in conjunction of the RDC/RDCi wheel electronics replacement.
M070115
Service Bulletin/Repair Instructions
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
M130115
Service Bulletin/Repair Instructions
N18:MINI Fuel Additive. INFORMATION Because carbon deposit buildup is related to fuel quality, it is not considered a defect in the vehicle's materials or workmanship. Consequently, the use of MINI Fuel Additive as outlined in this bulletin is not covered under the terms of the MINI New Passenger Car Limited Warranty, MINI Maintenance Program, any applicable Federal, State or MINI Emissions Warranty or the MINI Next Certified Pre-Owned Limited Warranty. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/217...4/7/2015
M110112
Service Bulletin/Repair Instructions
SI M11 01 12February 2015 EngineTechnical Service This Service Information bulletin supersedes SI M11 01 12 dated March 2014. designates changes to this revision SUBJECT N16 and N18 Engine: Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC
M340113
Service Bulletin/Repair Instructions
SI M34 01 13January 2015 BrakesTechnical Service This Service Information bulletin supersedes SI 34 01 13 dated May 2014. designates changes to this revision SUBJECT Erroneous "Service due" Message Although Brake Lining Thickness is Above Minimum Specification. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC
M840115
Service Bulletin/Repair Instructions
SUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received.
M210114
Service Bulletin/Repair Instructions
Dual Mass Flywheel: Diagnosis and Inspection. INFORMATION The following three criteria must to be checked, evaluated and the resulting findings documented on the repair order prior to replacing a dual-mass flywheel as defective: 1. Total rotational angle at no load condition (with applied torque less then 20 Nm) 2. Secondary plate longitudal axial play 3. Friction surface appearance changes due to thermal overload. PROCEDURE Refer to the attached "Dual-mass Flywheel Inspection" document for the complete inspection procedure. The dual-mass flywheel replacement is justified only if one or more of the following criteria are met: 1. The total rotational free-play measured at the flywheel gear ring is: Equal to or greater than 3 tooth gaps on N14/N18-equipped engines; Equal to or greater than 14 tooth gaps on B38/B46/B48-equipped engines. 2. The secondary plate total axial bearing play measured at outside diameter of the flywheel is: Equal to or greater than 3 mm on N14/N18-equipped engines; Equal to or greater than 5 mm on B38/B46/B48-equipped engines. 3. Significant discoloration in the adjoining area outside the friction ring, or a severe ablation/erosion of the friction area, is present. WARRANTY INFORMATION Warranty claims for replacing a Dual Mass Flywheel are subject to denial or debit when it is determined that the diagnostic procedures outlined above were not followed. ATTACHMENTS View PDF attachment M210114_Dual-Mass_Flywheel_Inspection.
SIM-11-10-14
Service Bulletin/Repair Instructions
MINI: SOME VEHICLES HAVE TURBOCHARGER NOISE AND A LACK OR LOSS OF PERFORMANCE, DUE TO RESTRICTION OF TURBOCHARGER OIL SUPPLY, RESULTING IN OIL STARVATION AND SEIZING OF TURBOCHARGER ASSEMBLY. MODEL ALL. *PE
M110414
Service Bulletin/Repair Instructions
N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.
M070114
Service Bulletin/Repair Instructions
ISTA Premium Repair Instructions. INFORMATION ISPI NEXT ISTA 3.45 introduces a new concept for displaying repair instructions. The new repair instructions have the following advantages compared to the old style: z All instructions (preliminary and follow-up) needed for the repair are included; hyperlinks are no longer needed. z All special tools needed for the repair can be viewed or printed from one tab in ISTA without leaving the repair instructions page. z All technical data and torque specs for the repair can be viewed from one tab in ISTA without leaving the repair instructions page. Currently repair instructions for the timing chain replacement "1131051 - Replace timing chain (N14)" have been converted to this new format. Refer to the attachment which describes how to access and use the instructions. To get initial feedback if any further changes are needed prior to converting all future repair instructions, we have converted the repair instructions used most often to this new concept. Please use these repair instructions when applicable and provide feedback using the attached feedback form. The form can be sent directly to Paul Labrie at Paul.Labrie@bmwna.com. Thanks for any feedback that you can provide. Paul Labrie Technical Service 201- 571-5247
M120211
Service Bulletin/Repair Instructions
Hesitation or Jerking Is Felt When Accelerating Between 3000 - 4000 rpm. A hesitation or jerking is intermittently felt when accelerating under higher loads between 3000 - 4000 rpm. No DME faults are stored. DME software error
M170812
Service Bulletin/Repair Instructions
Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor which is integrated into the thermostat housing (not replaceable). This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting or a "Service Engine Soon" lamp being illuminated.
M170912
Service Bulletin/Repair Instructions
Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor which is integrated into the thermostat housing (not replaceable). This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting or a "Service Engine Soon" lamp being illuminated.
M640110
Service Bulletin/Repair Instructions
?SI M64 01 10 Heating and Air Conditioning June 2014 Technical Service SUBJECT Howling/Rough Running Noise when the A/C Compressor is Engaged. The air conditioning compressor is excessively loud/running rough when the air conditioning system is switched on and the compressor is active. Vibration in the air conditioning suction line (low side).
M120114
Service Bulletin/Repair Instructions
N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software
M120214
Service Bulletin/Repair Instructions
N18: Service Engine Soon Lamp (MIL) May Come On at High Altitude. The Service Engine Soon lamp (MIL) is illuminated and engine power output is reduced. This could only occur only in areas high above sea level (greater than 5,000 feet) and more frequently with colder outside temperatures. The following faults will be stored in the DME, and no engine mechanical problems are found. * 2C56 - Charging pressure control, plausibility Pressure too high * 2C58 - Charging pressure control, switch-off: pressure build-up blocked Unfavorable DME software
M510312
Service Bulletin/Repair Instructions
Window Regulators Squeak when Moving Up or Down. The front side windows can make a squeaking noise when operated.
M120212
Service Bulletin/Repair Instructions
N16 and N18 Engine: Engine Ventilation Heating Faults Stored in DME Fault Memory After Programming. After reprogramming the vehicle to integration level R056-11-11-503 (ISTA/P P45.1.3.0) or higher, one of the following fault codes are stored in the DME fault memory: Vehicles with N16 engine: * 2F42 Engine ventilation heating, Control The Service Engine Soon lamp is not illuminated. Vehicles with N18 engine: * 37DE Engine ventilation, heating, triggering: open circuit The Service Engine Soon lamp is illuminated. CAUSE Due to a DME software change, the diagnostic monitoring capability is improved for the engine ventilation heating system. However, a fault will be stored in the fault memory because the engine ventilation heater circuit has a malfunction currently present. One of the following may be the cause: * Loose or defective electrical connection * Missing or defective crankcase ventilation heater relay.
M130114
Service Bulletin/Repair Instructions
N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, "Removing and installing or replacing high-pressure pump (N14, N18)" has a procedure error. The current version of the Repair Instruction states to replace the high-pressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Bosch High-pressure Pump (1): All vehicles equipped with the N18 engine and produced from 3/2012 and later When the engine is fitted with a Bosch High-pressure Pump (1), the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightening torques is correct. Refer to EPC for the applicable part numbers when making repairs.
M120113
Service Bulletin/Repair Instructions
N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5° C
M330112
Service Bulletin/Repair Instructions
Adjusting Rear Camber. Rear camber cannot be adjusted properly. CAUSE Repair instructions not followed properly
M510613
Service Bulletin/Repair Instructions
Bonnet Lock Difficult to Open or Close. The bonnet lock fails to operate correctly and is difficult to open or close. CAUSE Corrosion in the bonnet lock assembly
M520213
Service Bulletin/Repair Instructions
Squeaking Noise from Front Seat. A noise may be heard from the front driver's seat back when the customer applies sideways pressure during cornering. CAUSE Surface corrosion on the metal seat back frame can make a squeaking noise when rubbing against the foam rubber padding of the seat back.
M120112
Service Bulletin/Repair Instructions
N18 Engine: FC 37DE Engine Ventilation, Heating, Triggering Stored in the DME After Programming. The Service Engine Soon lamp is illuminated after reprogramming the vehicle to integration level R056-11-11503 (ISTA/P P45.1.3.0) or higher. When diagnosed, the following fault code is stored in DME fault memory: ??37DE Engine ventilation, heating, triggering: open circuit CAUSE Due to a DME software change, the diagnostic monitoring capability is improved for the engine ventilation heating system. However, a fault will be stored in the fault memory because the engine ventilation heater circuit has a malfunction currently present.
M120313
Service Bulletin/Repair Instructions
?N18 Engine: FC 2BF2 Rail Pressure Sensor Is Stored in DME Fault Memory. The customer states that the Service Engine Soon lamp is illuminated and the following fault is stored in the DME: FC 2BF2 Rail pressure sensor, workspace: pressure too high CAUSE A DME calibration error in the fuel pressure diagnostics results in an increased sensitivity.
M130113
Service Bulletin/Repair Instructions
N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, "Removing and installing or replacing high-pressure pump (N14, N18)" has a procedure error. The current version of the Repair Instruction states to replace the highpressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15601.2.M130113... 8/30/2013 Page 2 of 2 All vehicles equipped with the N18 engine and produced from 3/2012 and later. When the engine is fitted with a Bosch High-pressure Pump (1) the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightning torques are correct. Refer to EPC for the applicable part numbers when making repairs.
M340313
Service Bulletin/Repair Instructions
Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval.
M840213
Service Bulletin/Repair Instructions
Incorrect Customer Relations Telephone Number Is Saved in the Vehicle. The customer is not connected to MINI Customer Relations after dialing the number displayed in the vehicle Kombi or radio. CAUSE During the Pre-Delivery Inspection (PDI), the incorrect telephone number is being written into the vehicle. INFORMATION 1. When performing the PDI test plan, it is extremely important that you select MINI if the ISID is configured for both BMW and MINI. 2. After completion of the PDI test plan, verify that the customer relations number stored in the vehicle is correct. 3. The correct customer relations phone number is 1(866) 275-6464. 4. If the number stored in the vehicle is incorrect and the correct test plan was used, contact your 3g Administrator and have him or her verify the number stored in the ISID. 5.This picture shows the correct number stored in the Combox control unit. Note: To read out telephone number:
SI-M-13-01-13
Service Bulletin/Repair Instructions
MINI: THERE IS A PROCEDURAL ERROR IN THE REMOVING AND INSTALLING OR REPLACING HIGH PRESSURE PUMP CURRENT VERSION THAT HAS BEEN REPLACED WITH THE CORRECTED REPAIR INSTRUCTION PORTION FOR THE N14 AND N18 ENGINE. MODELS R55, 56, 57, 58, 59, 60, 61. NO MODEL YEARS LISTED. *PE
M340213
Service Bulletin/Repair Instructions
Clicking Noise from Front Axle Brakes.
M620113
Service Bulletin/Repair Instructions
Intermittent Humming or Buzzing Noise from Speedometer. When the vehicle is decelerating, an intermittent humming or buzzing noise coming from the instrument cluster may be heard when the speedometer needle is between 0 and 12 mph. Hardware error in the instrument cluster
M170213
Service Bulletin/Repair Instructions
PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Retrofit of Engine Coolant Temperature Sensor. Internal corrosion can form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading can lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.
M650512
Service Bulletin/Repair Instructions
DWA (Anti-theft Alarm System): False Alarm Is Triggered Intermittently. INFORMATION Parts replacement will not solve the problem if one or more of the conditions described in the situation above caused the alarm to trigger. The sensitivity of the interior ultrasonic sensor cannot be reduced. If the customer wishes to park the vehicle with the sunroof tilted, the window partially open, and/or in an area with excessive local noise, the interior sensor must be switched off by using the following procedure: Press the lock button on the remote control twice in succession. The LEDs flash in short succession for approx. 2 seconds. The interior ultrasonic sensor is switched off until the vehicle is unlocked and locked the next time. NOTE: This information can be found in the Owner's Manual in the "Controls" section under "Switching off the tilt alarm sensor and interior movement detector."
M110309
Service Bulletin/Repair Instructions
Whistling Noise from the Water Pump Area. A whistling or squealing noise is heard from the engine at idle and/or at higher engine speeds. CAUSE 1. Noise is caused by the water pump. 2. Noise is caused by the friction wheel of the belt tensioner.
M120612
Service Bulletin/Repair Instructions
Change in Thermostat Electrical Connector on Replacement Engine Harness. Vehicles produced from 3/2013 are no longer equipped with an engine coolant thermostat that incorporates the engine coolant temperature sensor (thermostat P/N 11 53 7 647 751). The engine coolant temperature sensor is now an individual component. To accommodate this component change, there was also a production change to the engine wiring harness; this also includes the replacement engine harnesses for earlier produced vehicles. The replacement harness is no longer equipped with the four pin connector for the thermostat / engine coolant temperature sensor, but two separate twopin connectors, one for the coolant thermostat and one for the engine coolant temperature sensor. *The N16 engine switched production to the 11 53 7 534 521 thermostat in 3/2012. This thermostat, like the new 751, incorporates a separate engine coolant temperature sensor. The connectors on the 521 thermostat will not match up to the connectors on a new, replacement engine harness. The 521 thermostat will need to be replaced with the 751 thermostat during this repair.
M110113
Service Bulletin/Repair Instructions
Service Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
M360113
Service Bulletin/Repair Instructions
MINI GP: Choice of Tire Option Agreement and Alternate Tire Retrofit. The Kumho 215/40 R17 Ecsta V700 sport tire performance optimization results in vehicle operation limitations, specifically when operated in cold climates or on wet, slushy or snow-covered roads. If your MINI JCW GP owner prefers a set of tires that better fits his/her driving style and climate, these owners can swap out the factory-original equipment (OE) Kumho 215/40 R17 Ecsta V700 sport tires for a set of the following MINI approved alternate tires: ??205/45R17 84W John Cooper Works performance run-flat tires Please refer to the attached MINI Product Planning & Strategy Bulletin M-20-0313-0012, "MINI John Cooper Works GP Unleashed," for more information, including the required "choice of tire option" agreement form.
M640113
Service Bulletin/Repair Instructions
Red or Blue Cap Missing from Temperature Control Wheel. The customer states the red or blue cap is missing from the temperature control wheel of the heat and air conditioning control panel.
M840113
Service Bulletin/Repair Instructions
Telephone: Phonebook Does Not Transfer to the Vehicle. The telephone book does not transfer to the vehicle after the pairing process is completed. CAUSE Software error in the head unit
M210113
Service Bulletin/Repair Instructions
Clutch Is Slipping or Grabbing. The customer states that the clutch is slipping or grabbing.
M650313
Service Bulletin/Repair Instructions
Basic SVS: Voice Recognition Inoperative After Programming. After programming the vehicle with ISTA/P 2.48.x, the voice recognition (Basic SVS) is inoperative. NOTE: The Basic SVS only includes voice recognition for phone functions. Error in the coding data of ISTA/P 2.48.x The voice recognition function is unintentionally deactivated.
M170712
Service Bulletin/Repair Instructions
Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.
M340112
Service Bulletin/Repair Instructions
ABS/DSC Control During Light Braking. When driving slowly over uneven road surfaces, there may sometimes be pre-mature ABS application relative to the driving situation with the brake lightly applied. Software in the Dynamic Stability Control unit (DSC)
M170612
Service Bulletin/Repair Instructions
Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.
SIM-17-06-12
Service Bulletin/Repair Instructions
MINI: ON ENGINE COOLANT TEMPERATURE SENSOR, INTERNAL CORROSION MIGHT BE FORMING, CAUSING A FALSE, INACCURATE ENGINE TEMPERATURE READING, LEADING TO DIFFICULTY IN STARTING ENGINE AND/OR A SERVICE ENGINE SOON ILLUMINATION. MODELS 2010-2012 R55, R56, R57, R58 (COOPER, COOPER S-CONVERTIBLE, CLUBMAN, HARDTOP, COUPE). *PE UPDATED 1/18/13. *PE UPDATED 3/11/2013 *JS
SIM-12-06-12
Service Bulletin/Repair Instructions
MINI: ENGINE COOLANT TEMPERATURE SENSOR, NOW AN INDIVIDUAL COMPONENT DUE TO CHANGE IN WIRING HARNESS AND REPLACEMENT OF HARNESS HAS TWO SEPARATE TWO PIN CONNECTORS, WHERE ONE FOR COOLANT TEMPERATURE SENSOR AND OTHER COOLANT THERMOSTAT. ALL MODELS BUILT UP TO 3/2012. *PE
SIM-16-01-09
Service Bulletin/Repair Instructions
MINI: INFORMATION PROVIDED REGARDING PROCEDURE OF REPLACING FUEL LEVEL SENSOR DUE TO FAILURE ON THE RIGHT AND/OR LEFT SIDE. *PE
SIM-12-03-11
Service Bulletin/Repair Instructions
MINI: SERVICE ENGINE SOON IS ILLUMINATED DUE TO TANK VENTILATION VALVE (TEV) BEING JAMMED OPEN AND FUEL CAP, WITH EVAPORATIVE SYSTEM LEAKAGE, WAS INCORRECTLY INSTALLED. *PE
SIM-13-02-11
Service Bulletin/Repair Instructions
MINI: THE TANK VENTILATION VALVE (PURGE VALVE) NO LONGER NEEDS TO BE REPLACED DUE TO IMPROVED RESULTS OF TEILECLEARING. *PE
SIM-32-01-09
Service Bulletin/Repair Instructions
BMW: INFORMATION ON THE BUMPER BRACKET CASTING FAILURE AND REPLACEMENT. *RM
SIM-17-01-10
Service Bulletin/Repair Instructions
BMW: ENGINE TOO HOT MESSAGE IS DISPLAYED WITH STORED TROUBLE CODES. THE WATER PUMP DOESNT POWER UP. *RM
SIM-11-07-08
Service Bulletin/Repair Instructions
BMW: DESCRIPTION AND SPECIFICATIONS OF CRANKCASE VENTILATION SYSTEM. *RM