Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
M010424
The automatic transmission limited warranty for the vehicle Selector Lever Magnetic Shift Interlock Mechanism (Gearshift lug assembly portion) has been extended to 10 years/120,000 miles, as determined by the vehicle’s original in-service date, when a gearshift lug repair kit installation procedure is required to be performed to address a displayed Check Control message (CCM) that states P not engaged - secure vehicle with parking brake against rolling away.
M511616
Cavity protection applied to underside of the hood is leaking out onto the wheel arch trim and grille.
M610607
MINI electrical systems have continued to develop over the past few years. As a result, the demand on the batteries has increased. Breakdowns due to an empty battery or problems in the vehicles electrical system can have various causes, most of which are not due to the battery itself. For this reason, a battery replacement will permanently eliminate the problem only in the rarest of cases. The energy diagnosis test module helps to localize these causes. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints. Without performing the energy diagnosis test plan, the root cause of a discharged battery cannot be identified. In order to properly repair the vehicle the first time, it is very important that the diagnostic test plan is performed to completion; with all results taken into consideration.
M110323
?BMW AG has issued a Delivery Stop: REPLACE CHARGE AIR LINE.
M540123
?The panoramic roof sunblind does not close, or jams while closing.
M610123
Oscillations in the electric drive can occur. As a result, the 12 V positive battery cable may rub against the battery box cover.
M610223
The buttons on the gear selector switch (GWS) do not work, or the function indicator lighting has failed.
M840322
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, MINI Assistance and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.
M630122
Ambient lighting changes color after the vehicle goes to sleep.
M220122
During a vehicle inspection and/or while addressing a customer's concern, the engine stabilizer bar/link appears to be worn.
M610820
During the service life of the vehicle, the high-voltage battery may unexpectedly not provide power to the vehicle.
SIM610321
The Check Control message "Door open" appears in the instrument cluster (Kombi) even though all vehicle doors are securely closed and locked.
M340317
Vehicles with total mileage below approx. 12,500 may experience premature wear of the left rear brakes. In some cases, there also may be visible damage due to thermal overload.
M230121
When the vehicle is on a lift and wheels are manually spun, a clanking noise is heard from the transmission area.
M360119
New RDC wheel electronics will be introduced with future generation MINI models. The new wheel electronics are identified as Huf Generation 5. These new wheel electronics will need to be programmed using the new tool when replaced or when depressurized (0 psi) for more than 2 minutes.
M610321
Any or all of the following CCM ID code 14/15/16/17 door open appear in the instrument cluster when the door is properly closed and locked. The locking operation of the door is not affected by the incorrect display.
M640221
Different air temperatures are felt from left to right out of the front fresh air grilles (air vents).
M651015
The Headunit High (HU-H), also called NBT came in vehicles with option 609. This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and came in vehicles with option code 609. This uses map North America EVO. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and came in vehicles with option 6UM. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and came in vehicles with option code 609 or 6NP . This uses map North America WAY.
M310115
A groaning and/or squeaking noise from the front axle occurs when turning at low speeds or idle
M220117
Creaking Noise When Cornering: A creaking noise is heard from the front end of the vehicle while cornering (predominantly left turns)
M660121
ACTIVE CRUISE CONTROL (ACC) CANNOT BE ACTIVATED: After the recent software update, the cruise control cannot be activated.
M410121
REWORKING THE PVC SEAM ON THE TAILGATE WATER CHANNEL: The body seam on the rear upper left of the body may not have been completely sealed, causing a water leak.
M610121
CLICKING NOISE IN VEHICLE INTERIOR DURING CHARGING: Clicking noise from the interior passenger side footwell when the vehicle is being charged, with the air conditioning running at the same time.
SIM110816
B38, B46 and B48 Engines: Engine Replacement Procedures
M640120
BUZZING NOISE IS HEARD WHEN AIR CONDITIONING IS DEACTIVATED: A buzzing noise is heard when the air conditioning (A/C) is deactivated while the vehicle is in park or neutral. Prior to turning off the A/C, the system was functional and cooling properly. A/C compressor, or The power supply to the A/C compressor is too low.
M640220
CONDENSATION FROM AIR CONDITIONING LEAKS INTO PASSENGER FOOTWELL: Condensation from the air conditioning systems evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.
M340120
SERVICE ACTION - PROGRAM THE BODY DOMAIN CONTROL (BDC) UNIT: Aftermarket scan tools cannot read fault codes in the Dynamic Stability Control (DSC) unit via the On Board Diagnostic (OBD) socket. The DSC data is not processed correctly in the BDC and therefore cannot transmit any diagnostic requests via the OBD using aftermarket scan tools.
M610520
MINI TURBOCORD PORTABLE EV 120V/240V CHARGER: The MINI-approved accessory TurboCord will not charge the vehicle.
M010520
B46M ENVIRONMENTAL AIR CATALYST SENSOR - LTD WTY EXT TO 15 YEARS/150,000 MILES: Component/Issue-Specific Limited Warranty Extension For the eligible vehicles, MINI USA, a division of BMW of North America, LLC ("MINI USA") is extending the limited warranty for the engine radiator's Environmental Air Catalyst (EAC) sensor (shown) to: 15 years/150,000 miles as determined by the vehicle's original in-service date.
M011116
OC3 SEAT OCCUPANCY MAT - LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES: Component-Specific Limited Warranty Extension For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (MINI USA) is extending the limited warranty for the front passenger's OC3 seat occupancy mat (shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date.
M160220
NOISES FROM THE FUEL TANK AT IDLE: While driving slowly with low RPM or while idling, a faint knocking or fluttering noise can be heard from inside the fuel tank when the tank is full. The customer may describe this noise as a "helicopter noise" from the rear of the vehicle.
M620318
BLACK SPOT IN THE CENTRAL INFORMATION DISPLAY: A small black spot remains on the Central Information Display's (CID) illuminated screen which does not go away after a key cycle or sleep mode. Dead pixels in the Liquid Crystal Display (LCD) diodes. Each individual light pixel on an LCD screen is made up of three diodes- red, blue and green. If all three fail, the pixel will appear as a permanent black dot. Dead pixels can occur as a result of: Blunt force contact to the screen that does not result in a cracked surface Non-functioning diodes Manufacturer defects (e.g., gas bubble).
M660220
KAFAS (CAMERA-BASED DRIVER ASSISTANCE SYSTEMS) LIMITATIONS: KAFAS camera-based assistance system (without radar) is not operating up to customer expectations. Customers can report system errors such as: Vehicle equipped with camera-based ACC, brakes without apparent reason and then does not accelerate When ACC is active, the vehicle does not brake, although it is obvious it should brake; or it even accelerates KAFAS system deactivates independently, due to system limitations that are not clear to the customer KAFAS system cannot be activated due to system limitations that are not clear to the customer When accelerating from a standstill, the vehicle does not automatically start in "Follow mode" Road signs are sporadically not detected Lane departure warning sporadically fails to function For the situations described in this service information bulletin that pertain to normal system limitations, ISTA diagnosis does not show any relevant fault codes stored.
M130120
TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.
M220317
CREAKING NOISE FROM THE LOWER ENGINE AREA: This Service Information Bulletin (Revision 1) replaces SI M22 03 17 dated January 2018. During load reversal or taking off from a stop there is a creaking or droning noise heard from the lower engine area. CAUSE The bushing in the lower engine stabilizer link is working its way out of its aluminum housing thereby rubbing against the engine oil pan. The bushing in the lower engine stabilizer link (1) is working its way out of its aluminum housing. The aluminum housing starts to rub against the engine oil pan (2).
M510120
FRONT DOORS DO NOT LATCH IN COLD WEATHER: At ambient temperatures below freezing one or both front doors may not open when attempting to enter. In some cases after opening they may not correctly latch. A missing seal on the inner Bowden release cable may allow water to enter the cable sheathing and freeze.
M610220
CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear. When performing a vehicle test the following diagnostic fault codes are stored in the BDC: CD0420 - "error of Flexray controller on Flexray bus" D91FF9 - "Flexray message data drivetrain 2 (DT_PT_2): Timeout" This message may be read out in the ZGM control unit or Body Domain Controller CAUSE Software in the Body Domain Control unit (BDC).
M620119
CENTRAL INSTRUMENT PANEL LED SURROUND RING DOES NOT ILLUMINATE WHEN IGNITION IS TURNED ON: This Service Information Bulletin (Revision 2) replaces SI M62 01 19 dated January 2019.The central instrument's outer perimeter LED ring (arrows) does not illuminate when switching on the ignition or with the engine start-stop button. It only illuminates after direct actuation of a component (e.g. setting the temperature radio volume etc.). F57 shown; other models similar Software error in the Automotive Pixel Link driver (APIX driver). APIX is the serial high-speed Gigabit multichannel link that connects displays such as the LED ring with vehicle control modules.
M840818
CONNECTEDDRIVE/MINI ASSIST SYSTEM DIAGNOSIS INFORMATION: ConnectedDrive/BMW Assist features are partially or completely inoperative.
M640116
WATER INGRESS IN FOOTWELL AREA FROM A/C CONDENSATE DRAIN: This Service Information Bulletin (Revision 1) replaces SI M64 01 16 dated September 2016. The condensate drain hose is blocked by the heat shield - The condensate drain hose is not attached properly to the housing - The condensate drain hose was damaged during installation or previous repair.
M720120
SAFETY BELT WARNING GONG SOUNDS AFTER UNBUCKLING WHILE VEHICLE IS STATIONARY. After a vehicle has been programmed to an I-level greater than 19-11-5xx and lower than I-level 20-03-530; the safety belt (aka seat belt) acoustic warning sounds when in Park (engine running) and the safety belt is unbuckled. The chime/gong lasts for up to 1 minute 40 seconds. The customer only expects the acoustic warning when the vehicle is moving and the safety belt is not buckled. The acoustic warning can occur when the seat is occupied and the safety belt buckle is opened on the driver's or passenger's side. Software in the ACSM4 Control Unit.
M110117
SETS DURING WINTER WITH COLD AMBIENT TEMPS: This Service Information Bulletin (Revision 8) replaces SI M11 01 17 dated May 2019. The Service Engine Soon (MIL) light is on together with the following fault stored in the Digital Motor Electronics (DME). Fault Code: Control Unit: Fault Code Text: 118002 DME Mixture control: Fuel-air mixture too rich In the situation being described the fault is only stored during the cold winter months. Note: Various other causes for a rich mixture fault are possible and should not be overlooked. DME software diagnostic is too sensitive This situation is most likely to occur if the driving profile is one of frequent cold engine starts and/or primarily short distance trips (idle / low load operation) where full engine operating temperature is not reached Due to the lower engine oil temperatures crankcase vapors that contain a higher fuel content are not completely drawn off via the crankcase ventilation system A false DME adaptation routine could then lead to this fault being set.
M110120
MALFUNCTION INDICATOR LAMP IS ILLUMINATED WITH A CRANKSHAFT ADAPTION FAULT: When diagnosing an illuminated malfunction indicator lamp (MIL) and/or a different issue the following fault may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.
M320114
Power-assisted Steering Intermittently Not Available at Engine Startup This Service Information Bulletin (Revision 1) replaces SI M32 01 14 dated October 2016. The power assisted steering is unavailable at start up/drive readiness. No communication with the Electric Power Steering (EPS).
M130118
DME FAULT CODE 1B8004 ENVIRONMENTAL AIR CATALYST(EAC) SENSOR: The Malfunction Indicator Lamp (MIL) light is on and the following fault code is stored in the DME: 1B8004 - EAC Sensor: Temperature - Engine coolant temperature radiator outlet comparison to each other implausible DME software calibration error for EAC sensor diagnostics.
M510419
POWER WINDOWS INOPERATIVE. The power windows won't operate in any direction. CAUSE Possible faulty window motor.
M610319
VEHICLE WILL NOT UNLOCK USING THE REMOTE CONTROL KEY BUTTON. The vehicle cannot be unlocked using the remote control key button. However, Comfort Access operates normally on the front doors and the tailgate. In addition, the Check Control Message (CCM) for Tire pressure control is present on the Central Information Display (CID). The following fault codes may be stored in the Dynamic Stability Control (DSC) control unit: 480A46 - Tire Pressure Monitor D35694 - Message Missing Software error in the Body Domain Controller (BDC).
M710119
SERVICE ACTION: REPLACE UNDERHOOD EMISSIONS LABEL. An incorrect "Group" number may be listed on the underhood emissions label for certain model year 2020 vehicles.
M510319
RATTLE FROM FRONT DOOR: A rattle noise is present from the door while driving most commonly when driving over rough roads.
M540119
SUNROOF WILL NOT OPEN: The sunroof does not move and the vehicle has no faults stored related to the sunroof. A software error in the FZD (Roof function center).
M540219
RATTLE NOISE FROM SUNROOF WHILE DRIVING: A rattle noise is present from the sunroof while driving only with the sunroof glass in the closed position.
M130119
LIN BUS COMMUNICATION FAULT FOR ENVIRONMENTAL AIR CATALYST (EAC) SENSOR FC1B8302. The malfunction indicator lamp light is on (MIL) with the following fault code stored in the DME.
M650219
SECURITY IMPROVEMENTS FOR HEAD UNITS. Security patches for non-safety critical vulnerabilities in MINI head units Entry Nav Entry Media NBT and NBT EVO.
M120219
DIAGNOSTIC HINT: CATALYTIC CONVERTER INSPECTION AFTER LOSS OF CRANKSHAFT SIGNAL: In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.
M240119
EGS FAULTS STORED AFTER AISIN TRANSMISSION REPLACEMENT. Due to hardware changes in the AISIN GA6F21AW or GA8F22AW transmissions.
M650119
Safety Systems HEAD UNIT NBT EVO (HU-H2) PROGRAMMING ABORT. During programming several aborts can occur in the head unit NBT EVO (HU-H2).
M840319
BLUETOOTH CONNECTION IS LOST DURING A PHONE CALL. During an active call the call audio autonomously switching from the vehicle hands-free system to the phone. The Bluetooth connection returns after a vehicle sleep cycle (20 minutes).
M840918
TELEMATICS CONTROL UNIT ACTIVATION VIA DCSNET FOR MINI ASSIST.
M010817
N16 ENGINE IGNITION COILS: LIMITED WARRANTY EXTENSION TO 10 YEARS/120000 MILES This Service Information bulletin supersedes SI M01 08 17 dated February 2018.
M650117
AIR BAG WARNING LAMP CC MESSAGE 'RESTRAINT SYSTEM' This Service Information bulletin replaces SI M65 01 17 dated February 2017.
M840119
SAMSUNG SMARTPHONE WITH ANDROID 8 NO USB AUDIO PLAYBACK OR CHARGING FUNCTION. The Samsung Smartphone running Android 8.x does not support USB audio playback and/or charging of the device via the USB port.
M840219
PHONE CALL AUDIO AUTONOMOUSLY SWITCHES FROM VEHICLE TO PHONE. During an active phone call the call audio autonomously switches from the vehicle hands-free system to the phone.
M120119
SERVICE ACTION: LOCK THE DME FAULT MEMORY. The fault memory lock in Digital Motor Electronics (DME) control unit was not activated. This lock should prevent the manual deletion of permanent fault codes. The DME fault memory lock has not been set.
M160119
ENGINE STALLS AFTER STARTING OR WILL NOT START. The engine stalls right after starting (when stationary).
M650418
AIRBAG INDICATOR LIGHT REMAINS ON AFTER SEAT OCCUPANCY MAT REPLACEMENT. The airbag indicator light illuminates after replacing the CIS (Capacitive Interior Sensing) mat.
M650116
XM Satellite Radio Reception. INFORMATION Currently Satellite Radio is provided by SiriusXM for MINI customers. SiriusXM is the only company currently broadcasting Satellite Radio in North America. Satellite radio was broadcast from two different sets of Satellites using different earth orbits. XM uses geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. This is different than Sirius Satellites in a Highly Elliptical Orbit (HEO) which came in to the vehicle at a higher angle to the horizon. As of April 2016 Sirius equipped head units moved to the XM Satellites constellation and now show the same location based cutouts.
M230108
MANUAL TRANSMISSION - STIFF DIAGONAL GEARSHIFT LEVER MOVEMENT. The customer may complain of a "stiff diagonal shift" (e.g., N-R, R-N, 2-3/3-2 or 4-5/5-4). Also, in some cases, gears cannot be selected, or the selector gear does not go into the neutral position. CAUSE 1. The deflection lever circlip of the gearshift mechanism is damaged or missing. 2. Possible corrosion at the gearshift mechanism (shift cables or transmission gearshift unit)
M510817
TRUNK OPEN MESSAGE ON CLUSTER. Check Control Message (CCM) "Trunk Open" message is displayed. Trunk is closed and latched. Improper attachment of trunk lock connector.
M540318
RATTLE NOISE FROM SUNSHADE WHILE DRIVING. With either of the sunshades fully opened, there is a rattle noise present when driving over rough road surfaces The sunshade is contacting the roof liner trim.
M610318
THE DISPLAY GOES BLACK, THE ENGINE CAN BE SWITCHED OFF ONLY VIA THE EMERGENCY-OFF.. * On board computer and navigation system goes black or resets. * The engine can only be switched off by pressing the START/STOP button three times (Emergency STOP) * Various Check Control messages are displayed * At a minimum the following fault code is present: D91C86 - CAN message, status functional safety (ST_FSSY): Timeout-BDC * Additional fault messages may also be displayed Software error in the central gateway of the Body Domain Controller (BDC) control unit. Note: Parts replacement does NOT provide a solution!
M510916
?TAILGATE UNINTENTIONALLY OPENS. Customer inquires about tailgate opening process, mentioning: * Trunk/tailgate may open when vehicle is locked. * Trunk/tailgate may open while the vehicle is in motion. * Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.
M120115
ENGINE MISFIRE DUE TO FAILED IGNITION COIL: The Check Engine or Service Engine Soon (MIL) lamp is on with misfire fault(s) stored in the DME.
M170115
ENGINE CRANKS, NO START AND/OR ENGINE COOLANT TEMPERATURE FAULTS: NOTE: The engine may also exhibit the same starting behavior as in Situation1.
M540118
SUNROOF WILL NOT CLOSE: The sunroof glass will not close, and the sunroof glass panel may appear twisted in the roof frame.
M620218
VEHICLE CHECK DISPLAYS DUE IN CBS DATA AFTER RESET FOR 2ND OIL SERVICE: After reset of service interval (e.g. oil change), the vehicle check is displayed as ÒDueÓ (yellow).
M840718
PHONE CONTACTS: HEADUNIT BASIC 2 SORTING ORDER: Improper sorting of phone contacts, in the on-board computer or in the Central Information Display (CID), upon connecting to the vehicle:
M510616
SQUEAKING NOISE FROM POWER FOLDING EXTERIOR REARVIEW MIRRORS: A squeaking noise can be heard when folding the exterior rear view mirrors in or out.
M640117
FOUL, MUSTY ODOR FROM HVAC: WET FOOTWELL CARPET: The customer reports one, or both, of the following:
M650610
NAVIGATION SYSTEM HAS MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
M650617
COMPONENT PROTECTION ACTIVE. HEAD UNITS CANNOT BE SWAPPED BETWEEN VEHICLES FOR TESTING.
M120618
JCW ENGINE TUNING KIT - ENGINE LOSS OF POWER IN STOP-AND-GO DRIVING: The engine may lose power if the vehicle is decelerated, in gear, to a near stop and then accelerated again.
M510715
PAINT ON THE B-PILLAR IS SCRATCHED/DAMAGED: The paint finish of the door jamb (above the door striker) is scratched due to the inner door cavity window seal.
M840518
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when:
M510516
WATER LEAK IN REAR HATCH: Water is found in trunk area.
M610216
HORN DOES NOT WORK: Horn operation is difficult or impossible.
M620415
INSTRUMENT CLUSTER OUTSIDE TEMPERATURE DISPLAY IMPLAUSIBLE: In the Instrument Cluster (Kombi) display you may observe an implausible outside temperature reading.
M660218
CHECK CONTROL STATES REMOTE KEY IS MISSING WHEN THE KEY IS LOCATED IN THE VEHICLE: Only vehicles that have been programmed with ISTA 4.10.1x and I-level 18-03-511 or 18-03-512.
M840418
IPHONE: CALL LIST MISSING AFTER RESTART: The call list from iPhone 8 or iPhone X, that is displayed, is missing after cycling the ignition.
M120318
BUZZING NOISE FROM VALVETRONIC MOTOR BEFORE OR AFTER ENGINE OPERATION: Buzzing noise may be heard from the Valvetronic motor when the vehicle is unlocked, before the engine is started, or after engine is turned off.
M120418
NOISE COMING FROM OIL FILTER AREA AFTER A COLD START: repeating fizzing noise may be heard from the engine oil filter area after a cold start.
M120718
ROUGH RUNNING WITH VARIOUS VANOS FAULTS: The check engine light is illuminated and the vehicle may run rough.
M630118
SERVICE ACTION: REPLACE THE LEFT FRONT LIGHT ELECTRONICS CONTROL MODULE: The FLE_L (Front Light Electronic _ Left) module - left side malfunctions.
M630318
SERVICE ACTION: REPLACE THE LIGHT ELECTRONICS CONTROL MODULES ON BOTH SIDES: The FLE (Front Light Electronic) module on both sides malfunctions.
M110119
ENGINE VIBRATIONS OR NOISE. One of the following complaints may be reported: The engine runs erratically; The engine causes vibrations when running; Grinding noise from the engine compartment when engine is running.
M240118
AISIN AUTOMATIC TRANSMISISON: RIGHT SIDE OUTPUT SHAFT SEAL REPLACEMENT
M410218
SERVICE ACTION PVC SEAM ON TAILGATE WATER CHANNEL COULD LEAK WATER; CHECK AND REWORK. Water may leak into the luggage compartment from inside the D-Pillar. Insufficient sealing of the D-Pillar sheet metal.
M620217
FUEL GAUGE ERRONEOUS DISPLAY: Vehicle runs out of fuel but the instrument cluster still displays fuel remaining in the tank.
M840218
HEAD UNIT HIGH RESETS WITH CONNECTION OF IPHONE 8, IPHONE 8 PLUS OR IPHONE X
M650118
NO AUDIO PLAYBACK AFTER REPLACING THE HEAD UNIT HIGH 2 (HU-H2): After replacing the Head Unit High (HU-H2) and performing ISTA4 programming there is no audio playback.
M120917
THE ENGINE STARTER INTERMITTENTLY DOES NOT CRANK OVER: The engine will not start, either consistently or intermittently.
M320116
EPS INTERMITTENT ASSIST FAILURE, FC 4823FA: The steering assistance fails after several, consecutive parking maneuvers or sustained hold at the end stop.
M660617
EMERGENCY START FUNCTION DOES NOT WORK WITH DEAD REMOTE BATTERY: Remote battery is dead.
M640217
AIR CONDITIONING COOLING IS INSUFFICIENT. * With option code SA 530 air conditioning or SA 534 Automatic air conditioning Produced from 2/1/2016 through 9/30/2016. * A/C system contains little or no A/C refrigerant. Contaminants under O-ring seals have allowed refrigerant loss.
M650717
NAVIGATION PRO (NBT EVO) MAP UPDATE NOT POSSIBLE, NAVIGATION DOES NOT START. A. Navigation system will not start at all or the "Navigation system starts" message is permanently displayed. B. While attempting to update the Navigation system's map, it will not update. Subfolder on internal Hard Disk Drive (HDD) is missing.
M120617
SERVICE ACTION:PROGRAM CONTROL UNITS (DME). During certain driving situations, there could be an uncomfortable transition when slowing or decelerating and then reaccelerating. CAUSE Unfavorable DME software
M360115
CHECK CONTROL MESSAGE: TIRE PRESSURE MONITOR (RDCI) FAILURE. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware failure in the remote control unit (FBD3 antenna).
M620117
ERRONEOUS SERVICE INCLUSIVE CBS DISPLAY. After pre-delivery check or after instrument cluster exchange, MINI Service Inclusive is displayed although the vehicle does not feature the optional Service Inclusive coverage. Instrument Cluster display error
M640114
Automatic Deactivation of Recirculation Mode. The customer states the recirculation display goes out, even though the recirculation button was switched on. CAUSE The automatic recirculation air deactivation feature was introduced in July 2012. Note: If the customer dislikes this feature, it can be deactivated by using the following steps.
M220217
KNOCKING NOISE FROM THE ENGINE COMPARTMENT. There is a knocking noise coming from the engine compartment or the engine shakes during: z Engine start z When driving off from a stop z When applying brakes CAUSE Damage to the right side engine mount. The damage may be subtle (1st picture) or obvious (2nd picture). Inspect the right engine mount and replace if necessary.
M120317
?Primarily when vehicle is at altitudes higher than 1500m above sea level, and engine is at operating temperature, the idle is sporadically elevated (up to approx. 1200 rpm). MIL indicator is illuminated. Fault code 1E0001 - "Idle speed control: Speed too high" is stored in DME. CAUSE DME software error The DME software improvements come in 2 steps 1. Primary improvements with I-level XXXX-17-03-50x. 2. Additional minor improvements with I-level XXXX-17-07-50x (ISTA/P 3.62.0 - expected release July 6, 2017 or ISTA NEXT 4.06.1x -expected release June 23, 2017).
M410116
EDGE CORROSION IN THE DOOR JAMB AREA. Corrosion on inner door panels at the following holes and cavity openings: Door brake (1). Door wiring harness pass-thru (2).
M650516
SPORADIC FAILURE OF DIFFERENT AUDIO CHANNELS. Intermittently, different speakers may be inoperative during an entire drive cycle until the vehicle enters sleep mode and the vehicle is restarted. Shut-down of output circuit(s) from pressure variations caused by door shutting during diagnostic self-test. After unlocking the vehicle the Harman/Kardon (HK) Amplifier goes into a speaker self-test mode. If a door is slammed during this self-test vibrating the speaker cone, the HK amplifier may interpret the changing resistance of the speaker as a circuit failure. The HK Amplifier will then go into protection mode and turn off the output transistor(s) for the particular speaker(s) until the next selftest which is performed after the next sleep cycle.
M120117
MIL IS ON WITH FAULT CF0486 STORED IN THE EGS MODULE. The Service Engine Soon (MIL) light is on. The following fault is stored in the AISIN EGS module: z CF0486: EGS,PT-CAN2: Line fault/electrical fault It is possible the following Check Control messages could be displayed: z Engine fault! Power loss (CCM ID 29) z Drive faulty! (CCM ID 419) - The transmission is in the emergency program and the engine is running with reduced power. This fault occurs sporadically when the ignition is turned on or the engine started. Unfavorable DME software Only vehicles at the following I-levels are affected: z F056-16-03-50x or F056-16-07-50x.
M120217
?SERVICE ACTION: PROGRAM CONTROL UNITS (DME). Due to an error in the OBD diagnostics of the DME software, a marginal catalytic convertor or post catalyst oxygen sensor may not be detected as faulty.
M650417
LIST OF AVAILABLE FM RADIO STATIONS TEMPORARILY NOT AVAILABLE. As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an "update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/407...
M511416
? INTERIOR REARVIEW MIRROR MOVES OUT OF POSITION . The "manually-dimming" interior rearview mirror does not hold its set position when traveling over rough roads and/or with "low ambient" interior temperatures. The pivot ball surface finish does not provide sufficient friction for stable positioning.
M650317
. INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. MINI is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for MINI customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: ? Do not replace any parts ? Do not program or carry out other work on the vehicle ? Explain to customer about the new Wireless Communications Service (WCS) signalsWhen investigating Satellite Radio cutouts or a temporary loss of reception: ? Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna.
M660117
? COMFORT ACCESS LOCKING REQUIRES MULTIPLE BUTTON PRESSES . Locking vehicle with CA button requires two presses, with up to 3 second delay between presses. Body Domain Controller (BDC) software
M310117
FRONT SUSPENSION RIDE HEIGHT HAS DROPPED. INFORMATION Please refer to the Electronic Parts Catalog (EPC), using the VIN to locate the part numbers.
M120815
?REDUCED ENGINE POWER WITH EXHAUST CAMSHAFT SENSOR FAULT STORED. DME software error or incorrect oil viscosity. Ensure that the engine oil level is correct and no other VANOS or oil pressure faults are present.
M120916
?ENGINE MAY RUN ROUGH AFTER MSA ENGINE RESTART. Unfavorable DME software. Program and recode the vehicle using the latest version of ISTA.
M60116
?Front Windshield Wiper Noises. Customer complains wipers are noisy or chattering during wiper operation.
M650217
?Technical Service ERRONEOUS CID MENU ENTRY- 'IMPORT JOURNEY'. ?Import Journey (USB)? submenu item in the Stored Journeys menu of the Navigation system is not working.
M111316
Service Action: B38 Engine - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.
M120816
RATTLING NOISE UNDER LIGHT LOAD. Faint rattling noise is heard from engine while under a light load or in a coasting overrun condition. Normal turbocharger operational sounds. Depending on current Integration level, reprogram vehicle to improve engine acoustics. For conditions that are similar to the situation described: Run diagnosis with ISTA and check the level to which the vehicle has been programmed; Program and encode the complete vehicle using ISTA/P 3.60.0 or ISTA NEXT 4.02.10 or higher to integration level F056-16-11-500 or higher.
M510513
Creaking/Cracking Noise from the Upper Roof Area. A creaking noise can be heard from the rear roof area when driving on rough roads or uneven surfaces. The body shell roof support area, where the C-pillar is joined to the roof, is buckling, creating the noise.
M120716
COMMUNICATION FAULT FOR ELECTRIC FAN. The Service Engine Soon light is on with the following fault code stored in the DME: ? 1A2005 - electric fan: Communication fault DME software calibration
M310315
CRACKING NOISE IN THE AREA OF THE FRONT AXLE SUPPORT/WISHBONE This Service Information bulletin supersedes SI 31 03 15 dated February 2016. Cracking noise coming from the area of the front axle when driving over rough road surfaces, railroad crossings and speed bumps. CAUSE Wishbone rubber mount.
M340316
The front outer brake pads are worn more than the inner pads. The brake pad wear indicator has not been activated. Very aggressive driving
M651016
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
M120615
ENGINE POWER REDUCTION WITH CLUTCH DAMAGED"" FAULTS STORED This Service Information bulletin supersedes SI M12 06 15 dated July 2015. A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for a service visit. F54, F55, F56, F57Target Integration level: F056-16-11-501 or higherThe vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME. ? 1D3101 - Clutch: Damaged, transmittable torque too low ? 1D3201 - Clutch: Severely damaged, transmittable torque too low CAUSE 1. The DME software diagnostic for detecting excessive clutch slip is too sensitive. 2. The clutch is damaged."
M650816
echnical Service AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
M650916
No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: Battery discharge when engine off, Caution, no acoustic warning signals. CAUSE Non MINI approved (third-party supplier) USB cable plugged into the USB port. CORRECTION Install new MINI approved USB cable.
M111216
Service Action: B46 and B48 Engines - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.
M120616
MIL LIGHT WITH DME FAULTS 1B2002 AND 1F1A51 STORED. Service Engine Soon (MIL) light is on. Both of the following fault codes are stored in Digital Motor Electronics (DME) memory: 1B2002: "EWS protection against tampering: no starting value programmed" 1F1A51: "DME, internal fault: Read EEPROM faulty" Note: Only vehicles with DME MEVD17.2.3 produced or programmed to Integration level 16-03-50x - 16-07-50x - 16-11-50x are affected. Ineffective DME software.
M121714
DME FAULT 168A20 FOR KNOCK CONTROL: SYSTEM ERROR STORED This Service Information bulletin supersedes SI M12 17 14 dated January 2015. A Check Control Message (CCM) is displayed: "Drive Faulty; Drive at moderate speed." Fault 168A20: Knock control; system error is stored in the DME. DME software
M210116
GROANING NOISE WITH CLUTCH OPERATION. Clutch operation may exhibit the following characteristics: produces a groaning noise, especially when engine is at operating temperature, during stopand-go travel. noise comes from transmission housing. noise can be heard in the interior and exterior of the vehicle. Friction between clutch slave cylinder piston rod end and ball socket (thrust piece).
M520116
HEATED SEAT TEMPERATURES INSUFFICIENT. Seat heater output is too low. Seat heating mat is ineffective.
M640214
Foul Odor when Switching On A/C. The customer reports a foul smell (musty, rotten, and vinegary) when the A/C is first turned on that lasts about five minutes. Micro-filter position too low in the IHKA housing.
M010316
B38 AND B48 LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the eligible vehicles, MINI USA a division of BMW of North America, LLC ("MINI USA") is extending the limited warranty for the leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Note: This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. ELIGIBLE VEHICLES To assist you in identifying the "eligible vehicles" that have this extended limited warranty coverage, the DCSnet Warranty Vehicle Inquiry will be updated with the VIN-specific "Vehicle Comment" shown below: MINI USA has extended the limited warranty for the leak diagnosis module (NVLD) on this vehicle to 10 years/120,000 miles as determined from the original in-service date. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. Please see SI M01 03 16. Warning: Before performing and submitting a repair under this extended limited warranty (ELW), always do a DCSnet Warranty inquiry to confirm that the vehicle has the above "Notice of Limited Warranty Extension" in the Vehicle Comment section. The "model year" production start (SOP) and end date (EOP) for a specific "model variant" within a "Series" will vary, please do not use a vehicle's production date as the sole determent for ELW coverage eligibility. If you have ELW eligibility and/or coverage question, please send an ema 10147064 20181105 M010316 20160801 Service Bulletin/Repair Instructions MINI COOPER S 2014 ELECTRICAL SYSTEM B38 AND B48 LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the eligible vehicles, MINI USA a division of BMW of North America, LLC (""MINI USA"") is extending the limited warranty for the leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Note: This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. ELIGIBLE VEHICLES To assist you in identifying the ""eligible vehicles"" that have this extended limited warranty coverage, the DCSnet Warranty Vehicle Inquiry will be updated with the VIN-specific ""Vehicle Comment"" shown below: MINI USA has extended the limited warranty for the leak diagnosis module (NVLD) on this vehicle to 10 years/120,000 miles as determined from the original in-service date. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. Please see SI M01 03 16. Warning: Before performing and submitting a repair under this extended limited warranty (ELW), always do a DCSnet Warranty inquiry to confirm that the vehicle has the above ""Notice of Limited Warranty Extension"" in the Vehicle Comment section. The ""model year"" production start (SOP) and end date (EOP) for a specific ""model variant"" within a ""Series"" will vary, please do not use a vehicle's production date as the sole determent for ELW coverage eligibility. If you have ELW eligibility and/or coverage question, please send an ema
M010416
B46 LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES FOR "NON-CALIFORNIA EMISSION" STATUTE STATES. INFORMATION For the eligible vehicles that are not eligible for coverage under the "State of California PZEV (SULEV) emission regulation," MINI USA a division of BMW of North America, LLC ("MINI USA") is extending the limited warranty for the leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Item #1: This componentspecific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty.Note: This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. ELIGIBLE VEHICLES To assist you in identifying the "eligible vehicles" that have this extended limited warranty coverage, the DCSnet Warranty Vehicle Inquiry will be updated with the VIN-specific "Vehicle Comment" shown below: MINI USA has extended the limited warranty for the leak diagnosis module (NVLD) on this vehicle to 10 years/120,000 miles as determined from the original in-service date. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. See SI M01 04 16. Vehicles that are registered in California or a State that has "fully" adopted the "State of California PZEV (SULEV) emission regulation." 10147572 20181113 M010416 20160801 Service Bulletin/Repair Instructions MINI COOPER S 2015 EQUIPMENT B46 LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES FOR ""NON-CALIFORNIA EMISSION"" STATUTE STATES. INFORMATION For the eligible vehicles that are not eligible for coverage under the ""State of California PZEV (SULEV) emission regulation,"" MINI USA a division of BMW of North America, LLC (""MINI USA"") is extending the limited warranty for the leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Item #1: This componentspecific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty.Note: This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. ELIGIBLE VEHICLES To assist you in identifying the ""eligible vehicles"" that have this extended limited warranty coverage, the DCSnet Warranty Vehicle Inquiry will be updated with the VIN-specific ""Vehicle Comment"" shown below: MINI USA has extended the limited warranty for the leak diagnosis module (NVLD) on this vehicle to 10 years/120,000 miles as determined from the original in-service date. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. See SI M01 04 16. Vehicles that are registered in California or a State that has ""fully"" adopted the ""State of California PZEV (SULEV) emission regulation.""
M111016
THERMOSTAT FAULTS (B-ENGINES). The Service Engine Soon light is on. A Check Control message for "Engine overheated" and or "Exercise caution!" may also display. The following fault codes may be stored in the DME: 1D2401 - Characteristic map thermostat, actuation: Short circuit to B+ 1D2402 - Characteristic map thermostat, actuation: Short circuit to ground 1D2404 - Characteristic map thermostat, actuation: Line disconnection During diagnosis the coolant may be found to be discolored. Insulation on the wiring for the map activation thermostat (heating element) may be damaged. Exposed wiring may allow coolant to enter the harness. This may cause damage to the heating element.
M340116
DRIVING STABILIZATION CONTROL FAILURE: ABS/DSC INSTRUMENT LAMPS LIT. ABS/DSC lamps lit in instrument cluster. Fault codes may be saved in the DSC control unit: 480AAD - wheel speed sensor - rear left - smoke monitoring 480AAC - wheel speed sensor - rear left - unexpected jump in the signal 4809B9 - wheel speed sensor - rear left - driving off recognition faulty 480716 - wheel speed sensor - rear left - plausibility: direction of rotation 4809B7 - wheel speed sensor - rear left - missing tooth 480719 - wheel speed sensor - rear right - plausibility: direction of rotation 480686 - wheel speed sensor - rear right - driving off recognition faulty 480AB3 - wheel speed sensor - rear right - unexpected jump in the signal 480AB4 - wheel speed sensor - rear right - smoke monitoring 4809C2 - wheel speed sensor - rear right - missing tooth Rear wheel pulse generator (wheel speed sensor) retaining screw is loose, missing or broken.
M340216
DRIVING STABILIZATION CONTROL FAILURE: ABS/DSC INSTRUMENT LAMPS LIT- DIAGNOSIS. 1. DSC's fault codes stored from two different wheel speed sensors (both front or both rear): 4809B0 - wheel speed sensor - front left - drive off recognition faulty and 4809CD - wheel speed sensor - front right - drive off recognition faultyor 4809B9 - wheel speed sensor - rear left - drive off recognition faultyand 480686 - wheel speed sensor - rear right - drive off recognition faulty. 2. Next ignition ON (after above codes stored). a) DME fault can occur:1F054D - drive, safety function: Drive power output reduced, DSC signals implausible and b) Malfunction Indicator Lamp (MIL) may light up. Faulty drive off recognition due to: a towing operation with a raised axle operation of the vehicle on the vehicle hoist operation of the vehicle on the roller test stand DSC diagnosis recognizes implausible wheel speeds, so no control is possible. DME fault is entered on safety grounds since the DSC fault still exists after a terminal change and may only be removed while driving.
M510716
ACTIVE REAR SPOILER IS STIFF MOVING IN AND OUT. The active rear spoiler binds while moving in and out. It also may not operate properly. The mechanics of the active rear spoiler are stiff and/or show corrosion.
M510816
WATER INGRESS, FRONT DOOR. Water found on Driver's or Passenger's side front carpet. Improper sealing of door at A-pillar.
M610116
SI M61 01 16 General Electrical Systems August 2016 Technical Service Front Windshield Wiper Noises This Service Information bulletin supersedes SI M61 01 16 dated April 2016.. Customer complains wipers are noisy or chattering during wiper operation. CAUSE Wiper arms out of adjustment and/or windshield cowl misaligned.
M620216
PERCEIVED SCRATCH IN INSTRUMENT CLUSTER. INFORMATION Replacing the instrument cluster for this issue will NOT be covered or reimbursed under MINI limited warranties. [ Copyright (c)2016 BMW of North America, Inc. ] Page 1 of 3 Page 2 of 2 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016 Page 1 of 3 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016
M650616
FM RADIO INTERFERENCE. Poor radio reception quality, short interruptions or a hissing noise in FM radio mode on weak radio stations. The wire harness which is run underneath the amplifier may be influenced by Electro-magnetic interference (EMI) from the amplifier. This can generate noise(s) under certain circumstances.
M110916
VANOS AND VANOS CENTRAL BOLT IDENTIFICATION. INFORMATION Replacing the VANOS gear central bolts or the VANOS gear will require a component inspection when the engine assembly has been previously replaced in one of the vehicles listed above. Ordering the parts via the model, production or VIN may provide the incorrect part numbers. The procedure below will help identify which VANOS parts are installed in the replacement engine. 11 36 7 608 788 Inlet adjustment unit Oulet adjustment unit Refer to the ETK and the repair instructions for one time use fastener and component information regarding additional screws, gaskets and seals.
M620515
The Clock in the Instrument Cluster Loses time This Service Information Bulletin supersedes SI M62 05 15 dated June 2016. The time displayed in the instrument cluster (KOMBI) may lose a few minutes each week and the clock needs to be adjusted periodically.
M640216
Air Conditioning Refrigerant R1234yf Introduction. INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipment may be an indication of refrigerant/equipment incompatibility with the vehicle's system. Always carefully ascertain the type of refrigerant used in the vehicle's system before performing service. Labels on underside of hood, will detail which refrigerant is used in the air conditioning system. Service the vehicle with compatible recycling equipment ONLY. Attempts to adapt and use incompatible service tools will destroy both the vehicle's air conditioning system and the service tool. Never use any R-12/R134a service tools on R1234yf systems. Tools, such as manifold gauge sets, retain small amounts of refrigerant and lubricant. Attempting to use the same equipment on both R-12/R134a and R1234yf vehicles will contaminate the air conditioning systems. Obtain and use the correct type of refrigerant recovery/recycling machine. Follow the directions included in the machine's instruction manual. WARR
M110315
B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil This Service Information bulletin supersedes SI M11 03 15 dated February 2016. The customer may have one of the following complaints: The engine malfunction light is illuminated with misfire or mixture faults stored in the DME. The vehicle runs poorly and may consume engine oil. Smoke from the exhaust tailpipe. Engine oil leak at the cylinder head cover gasket area. See illustrations for additional information. Engine oil leak (1) at the front edge of the cylinder head cover where it meets the cylinder head (2). In some cases the cylinder head cover gasket material may be bulging out from between the cylinder head cover and cylinder head mating surfaces. When the cylinder head cover is removed, the cylinder head cover gasket material is damaged near the crankcase ventilation drains or the bolt holes.
M120316
Service Action: Program Control Units (DME - VANOS). If the engine has been off for long period of time, when started it may run very rough at idle with the Service Engine Soon (MIL) light on. The engine power is reduced and a Check Control Message (CCM) "Drive Faulty; Drive at moderate speed" is also displayed. If the engine is then stopped and restarted the problem would no longer be present.
M630116
Delay in Automatic Driving Light Switching on/off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes. Shut-off period varies based on detected situation. This is normal operational behavior.
M660216
Collision warning and Pedestrian Warning Failed. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed CAUSE The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield, And/ or The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. KAFAS camera mounting bracket not secured correctly to the windshield. Notice the spacing between the white outline and the bracket. Possible solutions: Verify the KAFAS camera is installed (seated) properly in its bracket Replace the KAFAS camera Replace the windshield
M840114
Bluetooth Connection Failures This Service Information bulletin supersedes SI M84 01 14 dated February 2016.. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware
M110416
The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves "396" F55 and F56 vehicles produced from January 2014 to February 2015. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. UN
M110715
This Service Information bulletin and attachment supersedes SI M11 07 15 dated October 2015.. Excessive amount of water condensation may accumulate in the engine's crankcase. With prolonged vehicle storage, water condensation in engine's oil may cause oil pump malfunction. AFFECTED VEHICLES This Service Action involves F55 and F56 models (MINI Cooper with the B38 engine) produced from 07/05/2014 to 02/24/2015 that are: Still a "new vehicle" in dealer inventory (no in-service date reported), and the Current odometer mileage is 155 or less. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. Increased number of colds starts and stops during a vehicle's transportation and storage process (prior to customer delivery).
M110816
B38, B46 and B48 Engines: Engine and Cylinder Head Replacement Procedures. The engine may run rough and exhibit an engine noise from the VANOS area after the cylinder head or the engine is replaced.
M121214
VANOS Faults Stored in DME (Bosch). The Service Engine Soon (MIL) is on and the engine could go into a reduced power mode with the "Drivetrain Malfunction" message displayed. One or more of the VANOS faults (listed in the attachment) are stored in the DME, although the engine is mechanically sound and no unusual noises can be heard from the VANOS area. Due to unfavorable Engine Position Management (EPM) parameters in the DME software, various VANOS control faults could be set. These control faults relate to implausible camshaft position (intake or exhaust), the camshaft stuck situation, or the camshaft angle offset to crankshaft outside the tolerance range.
M510316
Air Intake Makes Rattle Noise At Engine Idle. Engine has rattle noise from engine compartment. Check Hyperlink for video of rattle noise at engine idle. http://tinyurl.com/zwb8e6s Worn buffer in the battery tray
M120216
Engine will not Start (No Crank). The engine will not crank or the engine loses power while driving, followed by a no crank situation. There is no communication with the DME when diagnosing with ISTA (DME is yellow on control unit tree). In certain instances, the startup of the turbocharger coolant pump can exceed the 5A rating of Fuse 83.
M650216
False Alarms of the Anti-Theft Alarm System. The alarm (DWA) siren continues to activate after locking vehicle A device is connected to the On-Board Diagnostics (OBD) port of the vehicle. This keeps the Ethernet communication line active which triggers the alarm when the vehicle tries to enter sleep mode.
M650316
NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI M65 01 16).
M651315
Hissing noise from speakers when radio volume is turned down. There is an audible hissing noise from the speakers when there is no active audio source. This noise is most apparent with the engine and climate system fan turned off. Software in the HK HiFi amplifier.
M660116
"Comfort Access Restricted" Check Control Message is Displayed. "Comfort Access Restricted" CCM (Check Control Message) is permanently displayed.. The CCM ID: D0h. The comfort access is functioning correctly. No comfort access aerial fault codes stored in the BDC (Body Domain Controller). Software error in the BDC.
SIM650416
Service Action: Program Vehicle to Activate Speech Recognition
M110216
SI M11 02 16 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 02 16 dated February 2016.. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves "382" F55 and F56 vehicles produced from February 2014 to December 2014. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. UN
M110316
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
M110516
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
M610115
This Service Information bulletin supersedes SI M61 01 15 dated February 2015. SUBJECT Noise from Steering Column Switch Center when Turning. The customer states that there is a grating or scraping noise when the steering wheel is turned. The noise comes from the area of the Steering Column Switch Center (SZL). When turning the steering wheel, the connection between the steering wheel and the SZL causes torsion stress, creating interference noise.
SIM610115
The customer states that there is a grating or scraping noise when the steering wheel is turned. The noise comes from the area of the steering column switch center.
SIM650116
XM Satellite Radio Recekption - Audio, Navigation, Monitors, Alarms, SRS
M121315
?SUBJECT Service Action: Program Control Units (DME) . A Check Control Message could intermittently be displayed indicating a Start/Stop Function failure. Vehicle may not restart after stopping. The following fault is stored in the DME: Fault 20BA20: clutch switch, signal: missing In addition the BDC may have the following fault stored: Fault 804084: clutch switch, plausibility fault compared to CAN signal This can occur if for example 14 gears changes are made, but the upper clutch position switch is only activated 10 times. This difference could occur when the clutch pedal is not being fully released between gear shifts or by resting a foot on the pedal so the upper switch position is not recognized.
M620116
?Vehicles which have had the Instrument Cluster (KOMBI) replaced may display incorrect CBS (Condition Based Service) data after programming.
M840215
SI M84 02 15 Communication Systems SUBJECT HU-B: Bluetooth Connection Fails Sporadically . Page 1 of 2 January 2016 Technical Service The Bluetooth system works intermittently. One or more of the following scenarios may occur: ? Bluetooth pairing is not possible - display shows "Please wait" ? Unable to select the check box to activate Bluetooth? Device does not reconnect to the vehicle after a key cycle ? Audio interference noise is heard listening to iPod etc. ? When trying to access the user manual, the display shows "Please wait" Incorrect software installed in the Radio MINI Visual Boost.
SIM120815
The engine power is reduced and a check control message (CCM) "drive faulty: drive at moderate speed" is displayed. DME software error
SIM121315
Service Action: Kprogram Control Units (DME)
SIM840215
HU-B: BLUETOOTH CONNECTION FAILS SPORADICALLY. INCORRECT SOFTWARE INSTALLED IN THE RADIO MINI VISUAL BOOST.
M090115
New programming feature: Exclusion of Infotainment Control Units from Programming.
M110815
Surface Cracks on the Water Pump Drive Pulley. During a repair, service or inspection, the drive pulley on the water pump shows signs of cracking. No part replacement is necessary unless there is another issue found that will be corrected by replacing the drive pulley.
M120415
B38, B46, and B48 Engines: Engine Noise, Drivability Complaints, and Various DME Faults. The vehicle exhibits one the following complaints: z Noise from the lower engine area, described as a high-pitched whine z Loss of power when idling z At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. z Extended cranking before the engine will start z The customer notices an increased level of "free play" in the clutch pedal when changing gears. z The clutch pedal remains depressed, and will not return to the disengaged position. z Emergency operation is active, with one or more of the faults listed below. One or more of the following faults may be stored in the vehicle: z 160020 Crankshaft sensor, signal: implausible z 180001 Catalytic converter: efficiency too low z 200D0C Powertrain, safety function: bus signal rpm reduction implausible z 11A002 Fuel high pressure, plausibility: Pressure too low z 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible Note: If additional faults are found in the DME memory (e.g., misfire, camshaft sensor, knock sensor, etc.), then those faults will be the primary focus of the diagnosis using the test plans provided for those faults. "FC 120408 Boost pressure control: Shut-down as a consecutive reaction" is only a result of the component fault and is not the primary reason for the complaint or https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/286...1/4/2016 Page 2 of 2 illumination of the engine malfunction warning.
M210115
B38, B46, and B48 Engines: Clutch Operation, Engine Noise, and Drivability Complaints. The vehicle exhibits one the following complaints: z The customer notices an increased level of "free play" in the clutch pedal when changing gears. z The clutch pedal remains depressed and will not return to the disengaged position. z Noise from the lower engine area described as a high-pitched whine z Loss of power when idling z At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. z Extended cranking before the engine will start z Emergency operation is active with one or more of the faults listed below. One or more of the following faults may be stored in the vehicle: z 160020 Crankshaft sensor, signal: implausible z 180001 Catalytic converter: efficiency too low z 200D0C Powertrain, safety function: bus signal rpm reduction implausible z 11A002 Fuel high pressure, plausibility: Pressure too low z 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible Note: If additional faults are found in the DME memory (e.g., misfire, camshaft sensor, knock sensor, etc.), then those faults will be the primary focus of the diagnosis using the test plans provided for those faults. "FC 120408 Boost pressure control: Shut-down as a consecutive reaction" is only a result of the component fault and is not the primary reason for the complaint or illumination of the engine malfunction warning.
M120414
Turbocharger Coolant Pump: Fault Code 20A503. "Drive Faulty" message is displayed in the Check Control. Fault code 20A503 "Turbocharger coolant pump, self diagnosis: Signal implausible" is stored in the DME. Unfavorable DME software application
M011014
MINI Motorer-Focused Satisfaction (MFS) Program. Based on Motorer feedback, MINI has determined that during the first three years of service, some vehicles may require specific additional service work to be performed. To address this issue, MINI USA, a division of BMW of North America, LLC ("MINI USA") is providing the following Motorer-Focused Satisfaction (MFS) Program. This program's procedures have been available to you to address specific Motorers' concerns since September 1, 2014. As part of our Motorer Pledge to deliver an incredible MINI motoring experience, for the abovereferenced MINI vehicles, we developed this program to increase our Motorers' satisfaction by helping to prevent unexpected dealer service repair visits.
M330115
Noises from the Rear Axle Shock Absorber. The customer complains about a hammering noise from the rear axle area, when driving on rough road surfaces with low ambient temperatures. This noise will disappear with warmer ambient temperature. CAUSE Rear axle shock absorbers
M620115
Door Open Message Displayed, Even Though Door Is Closed. While driving, a CCM (Check Control Message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. The FRM (Footwell Module) sees an incorrect door lock status caused by voltage variations in the door locks.
M640215
The Blower Motor is Faulty. The blower motor does not operate at any fan speed. The blower motor may work intermittently with the blower fan speed operating only on FULL speed. CAUSE The blower motor is faulty and causes the blower resistor to fail.
M640315
Intermittent Failure of the Blower Motor. Intermittent failure of the blower motor at high vehicle speeds and/or strong headwinds. The fault code "0x801204 - blower output stage: Short circuit or blocked" is stored in IHX_I1 (Heater-air conditioning control unit) sets under the following conditions: High vehicle speeds. Or Driving into strong headwind. Sunroof in the open/tilt position and/or an open side window may cause situation to occur at lower speeds. The blower resumes operation again after 60 seconds. CAUSE High wind flow and wind force causes a current overload in the blower motor.
SIM640215
Designates changes to this revision - The blower motor is faulty
M110615
Engine Electrical September 2015 Technical Service. This Service Information bulletin supersedes SI B11 06 15 dated July 2015. designates changes to this revision SUBJECT B38, B46 and B48 Engines: Various Faults Related to Engine Oil Pressure. The engine malfunction warning and the engine oil pressure warning is illuminated. One or more of the following faults are stored in the DME: 1C2002 Engine oil pump: pressure too low 1C0301 Engine oil pressure regulating valve: Jams in a fully energized position 1FB801 Check Control message (ID 212): Engine oil pressure. Stop carefully
M160115
Fuel Filling Nozzle Shuts Off Repeatedly While Refueling. The fuel filling nozzle turns off repeatedly while filling the fuel tank, regardless of the pump being used. CAUSE Defective service valve located within the fuel tank assembly. The service valve mechanism can stick closed at times and restrict the vapor release to the carbon canister while filling with fuel.
M310215
In isolated cases, during the vehicles assembly, it is possible that one of the front spring struts was not correctly positioned in the swivel bearing.
M640115
Air Draft into Driver's Foot-well. With the blower motor on, a draft in to the driver's foot-well area can be felt. As shown in the picture, the plug is missing from the air conditioning housing near the driver's foot-well area. The missing plug may be found in the vehicle DO NOT reinstall since it fits too loose and may fall out again.
M650415
Business Navigation (HU Basic) - not possible to downgrade the navigation map. After replacing the HU Basic (Entry Navigation), the version of the navigation map cannot be downgraded to the version of the replaced HU Basic. This is caused by an error in the routing table which is stored in the Central Gateway Module. Therefore, no communication with the map server can be established.
M121115
In the seven affected vehicles, the DME control unit (Digital Motor Electronics) may have a manufacturing defect which could cause the engine not to start.
M650315
Real-Time Traffic Information (RTTI) is Not Displayed On the Map. Real time traffic information (RTTI) is not displayed on the map. This only affects the specific VINs (vehicle identification numbers) listed below. The vehicle was built incorrectly (without option 6UH).
11 06 15
MINI: DIFFERENT FAULTS ACTIVATES ENGINE MALFUNCTION AND OIL WARNING. *MA
12 06 15
MINI: BECAUSE OF THE DME SOFTWARE, AND A DAMAGED CLUTCH, THE DRIVETRAIN MALFUNCTION CHECK MESSAGE APPEAR. *MA
12 09 15
MINI: FAULTY SOFTWARE FOR THE TANK VENTILATION CONTROL DISPLAYS ENGINE THROTTLE REACTION WHEN TEMPERATURE IS HIGH OUTSIDE, AND MORE OBVIOUS IF THE TANK IS ONLY PARTLY FILLED. *MA
M120715
Reduced Engine Power with Misfiring and Valvetronic Shutdown. The engine misfires with the engine power reduced, and a Check Control Message (CCM) "Drive Faulty; Drive at moderate speed" is displayed. Various misfire faults and the following Valvetronic fault codes are stored in the DME: ? Fault 134A02: Valvetronic servomotor: Overloading ? Fault 135302: Valvetronic servomotor: Switch-off, Component protection CAUSE DME software error
M120915
Intermittent Poor Throttle Response at High Ambient Temperatures. The engine throttle response from a stop can intermittently be sluggish when the outside ambient temperatures are higher. Additionally, this can be more noticeable when the fuel tank is only partially filled. CAUSE DME software for fuel tank ventilation control
M310114
Knocking Noise from Front of Vehicle when Turning. While driving or with the vehicle stationary, a knocking or popping noise can be heard from the front of the
11 02 15
MINI: A MECHANICAL FAILURE AND DME SOFTWARE ERROR OF THE VANOS ACTUATORS CAUSE THE ENGINE TO RUN ROUGH WHICH ACTIVATES THE MALFUNCTION WARNING LIGHT. *MA
12 05 15
MINI: DUE TO FAULTY DME SOFTWARE, THE SERVICE ENGINE LIGHTS COMES ON, INCLUDING THE CHECK CONTROL MESSAGE FOR MOTOR FORCE DECREASE. *MA
12 07 15
MINI: FAULTY SOFTWARE CAUSES THE CHECK CONTROL AND ENGINE POWER REDUCED LIGHT TO APPEAR. *MA
M110215
B38 and B48 Engines: Rough Running and Various Faults for Camshaft Sensor Signal and VANOS Control Stored in the DME. The engine runs rough and the malfunction warning is illuminated. One or more of the following faults are stored in the DME: 130104 Variable camshaft timing control, intake: Control fault, camshaft jamming 130108 Variable camshaft timing control, intake: Control fault, position not reached 130304 Variable camshaft timing control, exhaust: Control fault, camshaft jamming 130308 Variable camshaft timing control, exhaust: Control fault, position not reached 130E11 Intake camshaft sensor, plausibility: Signal implausible 130E20 Intake camshaft: Angle offset with respect to the crankshaft lies outside tolerance range 130F20 Exhaust camshaft: Angle offset with respect to the crankshaft lies outside tolerance range 131401 Variable camshaft timing control, exhaust, cold start: Cannot be controlled 131501 Variable camshaft timing control, intake, cold start: Cannot be controlled 131808 Variable camshaft timing control, exhaust, cold start: Position not reached 131908 Variable camshaft timing control, intake, cold start: Position not reached CAUSE DME software error and/or a mechanical failure of the VANOS actuators, camshafts and the VANOS central bolt valves.
M110515
Service Action: Replace Oil Filter Housing Assembly. A coolant leak could occur at the oil filter housing, resulting in overheating, loss of power, and an engine warning light.
M120515
Engine Power Reduction with Electrical Wastegate Faults Stored. The Service Engine Soon (MIL) light is on, along with a check control message for engine power reduction. The following faults can sporadically be stored in the DME: B38M ? 123431 - Electric wastegate, adaptation: Limit position open implausible ? 123432 - Electric wastegate, adaptation: Limit position closed implausible B48M ? 123433 - Electric wastegate, adaptation: Adjustment range implausible The following fault can also be stored in either engine as a result of the engine power reduction: ? 120408 - Charging pressure control: Switch-off, pressure build-up blocked CAUSE DME diagnostic software
M230115
Manual Transmission Will Not Stay in First Gear. When starting off in first gear, the transmission may ?pop? into neutral. Insufficient spring tension in the shifting mechanism of the manual transmission
SIM-12-04-15
MINI: SOME VEHICLES ARE EXPERIENCING SEVERAL ISSUES AS WHEN IDLING POWER IS LOSS, BEFORE ENGINE STARTS, EXTENDED CRANKING, CLUTCH PEDAL FAILS TO RETURN TO DISENGAGED POSITION, A HIGH PITCHED WHINE NOISE FROM LOWER AREA OF ENGINE. MODEL F55, 56 (COOPER, COOPER S, JCW). NO YEARS LISTED. *PE
N-14-05-09
MINI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. QUESTIONS AND ANSWERS FOR TIMING CHAIN OF VARIOUS MINI. *PE
M121614
When Warm, Engine Fails to Start with Valvetronic Fault 135608 Stored. The engine cannot be started once it is already warm. The Valvetronic (VVT) is fixed at a minimum lift position. The following fault is stored in the DME memory: ? 135608 - Valvetronic: No movement identified DME software error
M240115
"Coasting" Feature May Not Function After Programming. After programming to I-level F056-14-11-50x or higher, "coasting" while in green mode may no longer function. This feature is shown as activated in the green mode menu, and no relevant faults are stored. An EGS software error (I-levels of F056-13-11-50x to F056-14-07-50x) leads to incorrect EEPROM data when programmed to an I-level of F056-14-11-50x or higher.
M360215
Valve Stem Replacement with Wheel Electronics. Tire pressure loss after replacement of the RDC/RDCi wheel electronics. Valve stems are not being replaced in conjunction of the RDC/RDCi wheel electronics replacement.
M510215
Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a "Vehicle Comment" in the DCS Warranty Vehicle Inquiry or ISPA Light. The text on the label does not conform to legal regulations.
SIM-12-06-15
MINI: INSTRUMENT CLUSTER DISPLAYING A MALFUNCTION DRIVETRAIN CHECK CONTROL DUE TO DAMAGE CLUTCH AND EXCESSIVE SLIP OF CLUTCH IS TOO SENSITIVE. MODEL 2015 COOPER, COOPER S (2 AND 4 DOOR). *PE
SIM-11-02-15
MINI: CAMSHAFT TIMING CONTROL INTAKE, CAMSHAFT JAMMING, SIGNAL IMPLAUSIBLE, POSITION NOT REACHED, TOLERANCE RANGE OUTSIDE, CANNOT CONTROL COLD START EXHAUST AND ENGINE RUNNING ROUGH WITH MALFUNCTION WARNING ILLUMINATED DUE TO SOFTWARE ISSUE. *PE
SIM-11-03-15
MINI: SOME VEHICLES ARE CONSUMING ENGINE OIL AND RUNS POORLY, FROM CYLINDER HEAD COVER GASKET AREA AN OIL LEAK FROM ENGINE AND ILLUMINATION OF ENGINE MALFUNCTION LIGHT IS ON. MODEL F56 (COOPER). NO YEARS LISTED. *PE
M-120115
FAILED IGNITION COIL CAUSES ENGINE MISFIRE. HIGH TEMPERATURES DURING OPERATION CAUSES DIFFERENT MATERIALS USED IN THE IGNITION COIL CAN DETERIORATE OVER TIME *CN
M070115
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
M130115
N18:MINI Fuel Additive. INFORMATION Because carbon deposit buildup is related to fuel quality, it is not considered a defect in the vehicle's materials or workmanship. Consequently, the use of MINI Fuel Additive as outlined in this bulletin is not covered under the terms of the MINI New Passenger Car Limited Warranty, MINI Maintenance Program, any applicable Federal, State or MINI Emissions Warranty or the MINI Next Certified Pre-Owned Limited Warranty. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/217...4/7/2015
M610315
Engine Starts on Its Own After Switching Ignition Off. After switching the ignition off, with the vehicle in neutral and the brake applied, the vehicle starts on its own after 1.5 seconds, without pressing the Start/Stop button. No faults are stored in the Body Domain Controller (BDC). Software error in the BDC
M660115
Comfort Access Inoperative. 1. Unlocking the vehicle with the Comfort Access button does not work. 2. Lowering both windows with the Comfort Access button does not work. Vehicles with option 6FP (MINI Visual Boost radio) and option 609 (Navigation Professional) are not affected. Software error
M110112
SI M11 01 12February 2015 EngineTechnical Service This Service Information bulletin supersedes SI M11 01 12 dated March 2014. designates changes to this revision SUBJECT N16 and N18 Engine: Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC
M250214
eAutomatic Transmission Selector Lever Will Not Move Out of Park. The transmission selector lever cannot be disengaged from the "P" position. This can occur very randomly and is difficult to reproduce. No faults are stored in the EGS control unit, and no warnings are displayed in the instrument cluster. For the most part, if the vehicle is locked and goes to sleep (the light in the hazard switch goes out), the problem is no longer present. Unfavorable EGS software
M510414
Driver's Side Exterior Door Handle Cover Cap Is Loose. The driver's side exterior door handle cover cap is loose or missing. Driver's side exterior door handle.
M610215
Check Control Message "Battery Discharge" Displays Intermittently. The customer states that a "Battery Discharge" check control message is displayed intermittently when the vehicle is started. The following fault code is also stored: DME "213901 - Power management: Reduction or switch-off of individual electrical consumers" DME/IBS software error.
M650115
HU-H Headunit: Navigation System Road Map Usage. INFORMATION For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all MINI dealers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set into the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly onto the hard disc drive (HDD) integrated into the HU-H by inserting the DVDs one by one into the HU-H internal DVD drive. It will take approximately 2 to 2.5 hours to download the entire database. Please note that the HU-H NAV road map DVD set is for workshop use only, and is not to be left in customers' vehicles.
M320115
SUBJECT Sporadic Electronic Power Steering (EPS) Warning Lamp when Starting Engine. An EPS warning lamp may light up in the instrument cluster intermittently when the engine starts. No steering assistance is available at this time. After a terminal change (switching the ignition off and on again), the warning lamp is no longer illuminated. Software error in the EPS control unit Fault code "FC 4823E6-Internal control unit-power pack faulty" may be stored in the EPS.
M840115
SUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received.
M840214
This Service Information bulletin supersedes SI M84 02 14 dated December 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this Service Action to be completed prior to customer delivery. AFFECTED VEHICLES This Service Action involves certain R5x, R6x equipped with COMBOX (CMedia), and F56 vehicles equipped with HU-H (option code 7L5). First check if a Service Action label with a code number 75 is already attached to the B-pillar. If code number 75 has been punched out, the campaign has already been performed, no further action is required. For the affected vehicles, the DCSnet Warranty Vehicle Inquiry "Vehicle Comment" and/or the Key Reader/ISPA Light application's "Comments Information on" tab has been updated to display the following message: Service Action SI M84 02 14: Bluetooth So 10147644 20181113 M840214 20150101 Service Bulletin/Repair Instructions MINI COOPER S CLUBMAN 2012 ELECTRICAL SYSTEM This Service Information bulletin supersedes SI M84 02 14 dated December 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this Service Action to be completed prior to customer delivery. AFFECTED VEHICLES This Service Action involves certain R5x, R6x equipped with COMBOX (CMedia), and F56 vehicles equipped with HU-H (option code 7L5). First check if a Service Action label with a code number 75 is already attached to the B-pillar. If code number 75 has been punched out, the campaign has already been performed, no further action is required. For the affected vehicles, the DCSnet Warranty Vehicle Inquiry ""Vehicle Comment"" and/or the Key Reader/ISPA Light application's ""Comments Information on"" tab has been updated to display the following message: Service Action SI M84 02 14: Bluetooth So
M110914
Service Action: Replace Oil Filter Housing Assembly. A coolant leak could occur at the oil filter housing, resulting in overheating, loss of power and an engine warning light.
M170114
Damage to Radiator when Removing Fan Cowl. There is coolant leaking from the radiator after performing repairs where the fan cowl was removed.
M210114
Dual Mass Flywheel: Diagnosis and Inspection. INFORMATION The following three criteria must to be checked, evaluated and the resulting findings documented on the repair order prior to replacing a dual-mass flywheel as defective: 1. Total rotational angle at no load condition (with applied torque less then 20 Nm) 2. Secondary plate longitudal axial play 3. Friction surface appearance changes due to thermal overload. PROCEDURE Refer to the attached "Dual-mass Flywheel Inspection" document for the complete inspection procedure. The dual-mass flywheel replacement is justified only if one or more of the following criteria are met: 1. The total rotational free-play measured at the flywheel gear ring is: Equal to or greater than 3 tooth gaps on N14/N18-equipped engines; Equal to or greater than 14 tooth gaps on B38/B46/B48-equipped engines. 2. The secondary plate total axial bearing play measured at outside diameter of the flywheel is: Equal to or greater than 3 mm on N14/N18-equipped engines; Equal to or greater than 5 mm on B38/B46/B48-equipped engines. 3. Significant discoloration in the adjoining area outside the friction ring, or a severe ablation/erosion of the friction area, is present. WARRANTY INFORMATION Warranty claims for replacing a Dual Mass Flywheel are subject to denial or debit when it is determined that the diagnostic procedures outlined above were not followed. ATTACHMENTS View PDF attachment M210114_Dual-Mass_Flywheel_Inspection.
M510814
Front Doors Will Not Latch. The front door(s) may not latch or lock correctly when opening or closing. The condition mainly occurs with high or low temperature changes, making it difficult to duplicate. This only affects the Magna door lock and models without option 323 (automatic soft close). Manufacturing tolerances of the door lock
M540114
Panoramic Sunroof Rattles. A rattling noise is heard coming from the sunroof. This occurs when driving over rough road surfaces with the sunroof roller-blind fully open. The sunroof roller-blind hand grip vibrates against the frame.
M650414
Automated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle by entering the 20-digit enabling code manually.
SIM-11-10-14
MINI: SOME VEHICLES HAVE TURBOCHARGER NOISE AND A LACK OR LOSS OF PERFORMANCE, DUE TO RESTRICTION OF TURBOCHARGER OIL SUPPLY, RESULTING IN OIL STARVATION AND SEIZING OF TURBOCHARGER ASSEMBLY. MODEL ALL. *PE
M110414
N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.
M310214
Noise from Front Axle Control Arm Hydraulic Bearing. When driving in high ambient temperatures on rough road surfaces, at speeds between 5 and 30 mph, a squeaking noise may be heard coming from the front axle. Hydraulic bearing of the front axle control arm
M370114
Knocking Noise from Rear Shock Absorber. A knocking noise may be heard from the rear axle. The noise only occurs when the Driving Experience Switch (FES) is set to "Mid" mode or "Green" mode. The noise cannot be heard in the "Sport" mode. Rear axle shock absorbers
M630314
Headlight Range Adjustment Does Not Work Up or Down. z Headlight-range adjustment (LWR) is not functioning correctly while driving. z Both headlights are set too low and are aimed too far downwards. The screw holding the ride-height sensor's bracket on the right front and/or right rear control arm is broken.
M650314
Vehicle in Transport Mode Cannot Be Unlocked with Remote Control. When the vehicle is in transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle is in transport mode, to reduce power consumption, the software is designed to disable the outside antenna receiver from waking up the vehicle.
M320414
Front Axle Brake Pad Wear Sensor Routing.During brake service, the brake pad wear sensor cable may be incorrectly routed and also fastened to the front brake caliper?s bleed valve dust cap. Incorrect routing of the brake sensor cable may cause damage to the cable or brake sensor, resulting in a brake warning message being displayed.
M610614
Start/Stop Button Must Be Pressed Several Times to Stop Engine. To turn the engine off when it is running, the Start/Stop button must be pressed several times. This error does not affect starting the engine. Body Domain Controller (BDC) application software error. BDC fault "8040A9 - Start-stop button SST: Incorrect operation (pushed at an angle)" is stored.
M720114
Delivery Stop: Head Airbag.A Delivery Stop has been issued on certain F56 vehicles produced from August 8, 2014 through August 14, 2014. These vehicles will need both head airbags replaced. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at ports of entry will be repaired prior to dealer delivery. This bulletin will be updated with instructions and warranty information when parts become available. Please contact your field representatives if you have any questions. Affected vehicles can be identified with a ?Vehicle Comment? in the DCS Warranty Vehicle Inquiry or ISPA.
SIM-61-06-14
MINI: THE START/STOP BUTTON NEEDS TO BE TOUCHED SEVERAL TIMES BEFORE THE ENGINE CAN BE TURNED OFF AFTER RUNNING. STARTING ENGINE IS NOT AFFECTED. POSSIBLE SOFTWARE APPLICATION ERROR. MODEL F56. *PE
M000314
?Incorrect Vehicle Identification Number (VIN) Labels Installed. Twenty-six "Model Year 2014" vehicles have incorrect VIN labeling that indicates they are "Model Year 2015." Incorrect VIN labels were applied at the factory. The 9th and 10th digits of the VIN indicate that it is a MY 15 (F), when in reality the vehicle is a MY 14 (E). This includes the NHTSA compliance label, VIN number in the windshield and the VIN number on the front strut tower.
M011214
MINI "AMP-up" Motorer Care Fleet Increases. MINI USA, a division of BMW of North America, LLC ("MIN USA"), is pleased to introduce the Aftersales Mobility Program (AMP) Motorer Care Fleet Increase. The "AMP-up" program is designed to support (on a temporary basis) your alternate transportation needs, even in challenging times. When a significant "service initiative" (Recall, Service Action or other program) is identified by MINI USA, and this "AMP-up" bulletin is referenced under the "Alternate Transportation" heading, it will allow you to temporarily "AMP-up" your fleet so you can focus on the important things, like Motorer care. We anticipate an increased AMP car demand, in volume and duration, in association with a release of a service initiative. Your Area Manager (AM) has a procedure to assist you in calculating and determining if a temporary fleet increase is needed at your dealer. This option is not available if your dealer already has an approved and active temporary fleet increase in place. Example communication within a service initiative or critical Motorer care notifications: Please refer to AMP Bulletin M01 12 14 for process details. In the communication example above, the following would be required: * All requests must be submitted no later than the Submission Period specified above. * An additional number of vehicles may be added to your existing fleet immediately upon approval and fully utilized for the duration of the pre-determined Increase Period. * Your fleet must be restored to pre-Motorer Care approved limits by the Fleet level Restoration Deadline date, without exception.
M121014
Service Action: Program Control Units (DME). Due to unfavorable DME software, the engine idle speed may be unstable and fluctuate at times.
M121314
The Service Engine Soon (MIL) On with Fault 102001: Air Mass Too High. The Service Engine Soon light (MIL) is illuminated with the Check Control message: "Drivetrain: Drive Moderately" displayed. Fault 102001: Air mass too high is stored in the DME. CAUSE Unfavorable DME software
SIM-31-01-14
MINI: THERE IS NOISE, POPPING OR KNOCKING, HEARD FROM FRONT OF VEHICLE, WHEN DRIVING OR STATIONARY, AND TURNING STEERING WHEEL TO LOCK POSITION AND IS CAUSED BY SCREW THAT IS CONNECTED BETWEEN CONTROL ARM AND SWIVEL BEARING. MODEL F56 HARDTOP. *PE
M120514
?Service Engine Soon Lamp (MIL) On with DME Fault 120408 Stored. The Service Engine Soon lamp (MIL) is illuminated with a reduction of engine power. Fault 120408: Charging pressure control: Switch-off, pressure build-up blocked is stored in the DME. CAUSE 1. This fault normally sets as the result of a problem with another component of the engine management system. 2. When there are no faults, the vehicle voltage might drop momentarily below the threshold of 9.985V, typically during an MSA engine start. This could result in the charge-air control being switched off.
M120614
At operating temperature, the engine idle speed could dip low. In rare cases, the engine may stall, requiring a restart. This could mostly likely occur at a low speed (2nd gear) when coasting off the throttle and slowing to a stop. This situation could be perceived as an MSA malfunction: intermittent and not easily reproduced. Unfavorable DME software.
M120714
B38M Shuts Off when Placed into Gear After Cold Engine Start. After a cold start, the engine idles poorly and could shut off when the transmission in placed into Reverse or Drive position. Unfavorable DME software.
M120814
Various Check Control Messages with Fault 11B033 Stored in DME. A drivetrain or MSA malfunction Check Control message may be displayed, along with a Service Engine Soon light (MIL). DME fault 11B033: Fuel pump control module (FPC), signal: Short circuit to ground is stored in the DME. CAUSE Unfavorable DME software diagnostics
M170812
Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor which is integrated into the thermostat housing (not replaceable). This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting or a "Service Engine Soon" lamp being illuminated.
M170912
Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor which is integrated into the thermostat housing (not replaceable). This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting or a "Service Engine Soon" lamp being illuminated.
M250114
Service Action: Manual Gear Shift Knob Loose. The manual transmission gear shift knob easily comes off the shift rod with minimal upward force.
M510614
Squeaking Noise When Operating Front Windshield Wiper. A squeaking noise can be heard when operating the front windshield wiper. Fitment between the cowl panels and the left windshield wiper post
M610314
Washer Fluid Leaks from Front Washer Jets. When operating the rear window washer, washer fluid leaks from the front windshield washer nozzles. Design issue with the windshield washer system
M330114
Delivery Stop/Service Action: Shock Absorber Rear Axle MODEL F56 (MINI Hardtop) SITUATION A rear shock absorber with a malfunctioning damper valve may have been fitted into some vehicles. Important note: In the group of identified vehicles, only four shock absorbers in total are affected. The damper function of these four units is only partially effective. These four shock absorbers can be identified, based on a particular date and serial number, as seen in the attachment M330114 Labels. This Service Action involves F56 MINI Hardtop vehicles produced from April 7, 2014 through May 14, 2014. First check if a Service Action label with a code number 67 is already attached to the B-pillar. If a code number 67 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
M610514
Front Windshield Washer Jets Not Working. When operating the windshield washer, very little or no washer fluid is coming out of the washer jets. The windshield washer hose shown below is too short. This causes it to kink or disconnect.
M110314
B38 and B48 Engines: Engine Oil Pressure Faults Stored in DME Memory. INFORMATION When diagnosing the vehicle, the following fault is stored in the DME: FC 1C0102 Engine Oil Pressure control, plausibility, static: pressure too low If the vehicle's integration level is not F056-14-11-500 or higher, and no other faults related to the engine oil pump or engine oil pressure regulating valve are stored in the DME, it can be ignored. This fault will not illuminate the Service Engine Soon lamp. When available, the vehicle can be reprogrammed to integration level F056-14-11-500 or higher to eliminate this erroneous fault. The release of this integration level is scheduled for December 2014. This bulletin will be updated when the applicable programming software is available. If one of the following faults is stored in the DME memory in conjunction with the fault above, or the oil pressure warning lamp is illuminated, proceed with diagnosing the vehicle with the applicable test plan for the fault stored. FC 1C2002 Oil pump, mechanical: Oil pressure too low And/or FC 1C0301 Oil pressure regulating valve, mechanical: hangs in a fully energized position (minimum oil pressure WARRANTY INFORMATION Not applicable.
M120114
N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software
M340113
Erroneous "Service due" Message Although Brake Lining Thickness is Above Minimum Specification. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.
M360114
Erroneous Check Control Message: Tire Pressure Check Failed. After pressing the Start/Stop button, Check Control message "Tire pressure check failed" appears briefly, as well as the corresponding light in the instrument cluster. These displays disappear after a few seconds. Software in the BDC (Body Domain Controller)
M510314
Transportation Protective Sleeve Introduced for Windshield Wipers. The windshield wipers streak and judder. The windshield wiper blades become distorted during transportation and when in storage.
M510514
F56 Make Good Program: Install Accessory Roof Graphic or Mirror Caps. Due to production restrictions at Plant Oxford, certain F56 vehicles produced in May and June of this year cannot be built with the factory option for the contrasting roof and/or mirror caps. This production issue was caused by the plant expanding its paint capabilities to meet increasing vehicle demand. In a continuing effort to maintain the utmost in Motorer satisfaction, MINI USA is offering our dealer partners an alternative solution, the "Make Good" program. For all affected MINI F56 vehicles: * Produced from May 1, 2014 to June 30, 2014 and * Built without the factory order "Contrasting Roof and Mirror Caps" option (382 and 383) Your MINI dealer can offer these Motorers the installation of an accessory roof graphic or set of mirror caps. The Motorer has the choice of either the accessory roof graphic or exterior mirror caps, not both. MINI Area Manager (AM) "Field Authorization" (FAS) is not required. Note: For eligible vehicles (VINs) that are affected by this production restriction, the procedure outlined in this bulletin only applies to mirror caps or roof graphics installed by your dealer. Mirror caps or roof graphics installed through the MINI USA "VIA" (VDC-Installed Accessory) program are not eligible for reimbursement through this Make Good Program.
M610414
Vehicle Honks for 20 Seconds when Left in Neutral. INFORMATION This is normal vehicle operation if the customer leaves the vehicle (with the key in pocket) in Neutral without being shifted into Park. The honking noise notifies the customer that if the shifter is not put into Park position, the vehicle will roll away or, if left alone for longer periods, have a discharged battery. Please refer to the attached information sheet for further information. Additional information may be found in the Owner's Manual for the vehicle. ATTACHMENTS View PDF attachment M610414_Flyer.
M630214
LED Headlight Malfunction Displayed, but Lights Function Properly. A check control message or warning light is on, indicating a headlight malfunction, but the lights operate correctly. The BDC (Body Domain Controller) fault code 8041B6: "Headlight (LWR): System failed" is the only fault stored. This fault can occur after QC1 is performed or after a vehicle software update. BDC (Body Domain Controller) software error
M710114
Service Action: Replace Wheel Bolt Wrench. The internal thread of the wheel bolt wrench is incorrect at M8. AFFECTED VEHICLES This Service Action involves F56 vehicles according to VIN selection. First check if a Service Action label with a code number 64 is already attached to the B-pillar. If a code number 64 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
M110114
Delivery Stop/Service Action:Replace Oil Filter Housing Assembly. A Delivery Stop has been issued on certain 2014 model year F56 vehicles produced from November 2013 to March 2014. A coolant leak could occur at the oil filter housing, resulting in overheating, loss of power and an engine warning light. Affected vehicles in dealer inventory must not be retailed or delivered until the oil filter assembly has been replaced. Vehicles at ports of entry will be repaired prior to dealer delivery. The affected vehicles are listed in the attachment to this bulletin; they are also identified with a "Vehicle Comment" in the DCSnet Warranty Vehicle Inquiry or ISPA, as follows: Defect Code 0011330300, Delivery Stop, Oil Cooler; see SI M11 01 14.
M110214
B38 and B48 Engines: Grease Residue Found at Bottom of Transmission Bell Housing. INFORMATION While performing repairs to the underside of the vehicle, the technician may notice yellow grease residue has formed on the lowest point of the transmission bell housing near the engine starter. The residue is not related to the engine oil or transmission fluid. The grease was applied to the starter during vehicle assembly. If the residue is noticed, the grease can be wiped away with a shop towel. The residue will stop accumulating after the engine has been operated for a few hundred miles. If the residue were to drip from the bell housing, it would be caught by the under body covering and would not create a customer complaint. In a severe case, some marks may be seen on the engine side of the under body covering. The grease drippings will not be seen on the ground under the vehicle. Do not remove or replace any components.
M120314
Service Action: Grease Engine Starter Electrical Terminals. Due to the location of the engine starter, the electrical contacts must be coated with special contact grease for protection from moisture and outside elements.
M630114
After deleting transport mode during PDI (QCI Pre-Delivery Inspection), fault code ?8041A9 - Daytime running light lock active? is present in the BDC (Body Domain Controller) and the DRL (Day Running Light) is switched off. CAUSE Software in the BDC.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.