Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
M230108
MANUAL TRANSMISSION - STIFF DIAGONAL GEARSHIFT LEVER MOVEMENT. The customer may complain of a "stiff diagonal shift" (e.g., N-R, R-N, 2-3/3-2 or 4-5/5-4). Also, in some cases, gears cannot be selected, or the selector gear does not go into the neutral position. CAUSE 1. The deflection lever circlip of the gearshift mechanism is damaged or missing. 2. Possible corrosion at the gearshift mechanism (shift cables or transmission gearshift unit)
M090115
New programming feature: Exclusion of Infotainment Control Units from Programming.
M110815
Surface Cracks on the Water Pump Drive Pulley. During a repair, service or inspection, the drive pulley on the water pump shows signs of cracking. No part replacement is necessary unless there is another issue found that will be corrected by replacing the drive pulley.
M610515
CAS Module Fails Programming with CoAPI Error 2082. During vehicle programming, the CAS (Car Access System) module fails to program with CoAPI error 2082 displayed. Refer to the attachment, which lists the affected CAS serial numbers. The following part numbers are affected: 61 35 9 287 534 61 35 9 226 238 61 35 9 227 053 61 35 9 287 535
M620115
Door Open Message Displayed, Even Though Door Is Closed. The customer complains that while driving, a CCM (check control message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. Unspecified FRM (footwell module) door lock status due to voltage variations
M110112
N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC Below is the procedure for identifying how far the engine oil has migrated inside the engine electrical harness, when this issue occurs, if at all. The procedure must be followed very carefully so that the proper repair is identified. 1. Disconnect the oil pump volume control solenoid valve electrical connection per Repair Instructions 11 41 519 "Removing and installing or replacing the solenoid valve (engine oil pump)." Inspect the electrical connector; if no engine oil is found inside the electrical connector, perform the oil pump volume control valve repair procedure. If engine oil is found inside the electrical connector, proceed to diagnostic procedure step 2. 2. Remove the cover from the DME and remove all three electrical connectors from the DME. Inspect the connectors for traces of engine oil. If no engine oil is found, perform the oil pump volume control valve repair procedure and replace the engine section of the wire harness. Refer to EPC for the additional part number. If engine oil is found in the DME connector, proceed to step 3. 3. If engine oil is found in the DME electrical connector, perform the oil pump volume control valve repair procedure, replace the engine section of the wire harness and replace the DME. Refer to EPC for the additional part numbers. Do not remove the engine oil pan. Do not replace the oil pump volume control valve. Do not replace engine oil pump. OIL PUMP VOLUME CONTROL VALVE REPAIR
M130114
N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, "Removing and installing or replacing high-pressure pump (N14, N18)" has a procedure error. The current version of the Repair Instruction states to replace the high-pressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Bosch High-pressure Pump (1): All vehicles equipped with the N18 engine and produced from 3/2012 and later When the engine is fitted with a Bosch High-pressure Pump (1), the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightening torques is correct. Refer to EPC for the applicable part numbers when making repairs.
M340113
?SI M34 01 13 November 2013 BrakesTechnical Service This Service Information bulletin supersedes SI 34 01 13 dated October 2013. designates changes to this revision SUBJECT Erroneous "Service due" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness.
M540513
Service Action: Convertible Top Does Not Close. During the closing process, it is possible that the convertible top locating pin on the right side is not correctly positioned in the landing plate at the top of the A-pillar (passenger's side). AFFECTED VEHICLES This Service Action affects certain R57 vehicles produced from July 2013 to October 2013. 3.This picture shows the left side locating pin correctly positioned in the landing plate on the driver's side A-pillar. 4.The passenger's side should In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 63. If code number 63 has been punched out, the campaign has already been performed. If code number 63 has not been punched out, it will be necessary to utilize the Service Menu" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A Campaign can be reserved in ISPA Light as "Pending" prior to submission of a claim. If you find this Campaign reserved, please verify the reason before attempting to perform this repair."
M000113
Vehicle Document Pouch Missing. The pouch in which the vehicle documents (e.g., Owner's Manual, Service and Warranty booklet, tire manufacturer warranty CD, etc.) are to be inserted during QC1 may be missing from the some of the vehicles in this production period. CAUSE There was a temporary supply shortage during a change of pouch suppliers.
M170213
PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Retrofit of Engine Coolant Temperature Sensor. Internal corrosion can form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading can lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.
M650512
DWA (Anti-theft Alarm System): False Alarm Is Triggered Intermittently. INFORMATION Parts replacement will not solve the problem if one or more of the conditions described in the situation above caused the alarm to trigger. The sensitivity of the interior ultrasonic sensor cannot be reduced. If the customer wishes to park the vehicle with the sunroof tilted, the window partially open, and/or in an area with excessive local noise, the interior sensor must be switched off by using the following procedure: Press the lock button on the remote control twice in succession. The LEDs flash in short succession for approx. 2 seconds. The interior ultrasonic sensor is switched off until the vehicle is unlocked and locked the next time. NOTE: This information can be found in the Owner's Manual in the "Controls" section under "Switching off the tilt alarm sensor and interior movement detector."
M610607
Discharged Battery: Energy Diagnosis Must Be Performed. MINI electrical systems and advancements in vehicle technology have resulted in an increased demand on the vehicle battery. This SI will help the dealer handle "discharged battery" complaints. A discharged battery can have various causes, most unrelated to the battery. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to http://www.batteryuniversity.com/parttwo-42B.htm. For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. To repair the vehicle properly the first time in the workshop, the diagnostic test plans must be performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair. CAUSE Discharged battery.
M540113
White Wear Marks on Canvas Top. Wear marks appear on the convertible top on the left and/or right side C-pillar areas. A For vehicles produced to December 12, 2011 1. Replace the defective canvas convertible top. Refer to ISTA Repair Instruction 54 34 120, "Replacing soft top fabric." Note: The following repair steps must be performed before the new top is installed to prevent a repeat repair for wear marks. 2. With the defective canvas cover removed, the current main pillars must be replaced. Refer to ISTA Repair Instruction 54 34 996, "Replacing left or right main pillar." 3. The current locking mechanisms and bump stops must be replaced as well. Refer to ISTA Repair Instruction 54 34 196, "Removing and installing / replacing both stowage locks." The repair kit* needed is listed below. 7. Reinstall the removed parts in the reverse order of their removal. 8. Operate the top several times to quality check the repair.
M320113
Noise from Steering Column when Turning or Adjusting Height. A squeaking noise is heard from the area around the steering column when turning or adjusting its height. CAUSE Material contact between the upper steering column bearing inner race and the plastic sleeve
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.