ITS59080
Service Bulletin/Repair Instructions
Technical Instruction for NABI model buses describing how to install a jumper harness to allow an upgraded engine Electric Control Unit (ECU) to properly function specific dash indication lamps.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITS59080
Technical Instruction for NABI model buses describing how to install a jumper harness to allow an upgraded engine Electric Control Unit (ECU) to properly function specific dash indication lamps.
SSM 49440
Some 2020 Mustang GT500 vehicles may exhibit various transmission related concerns and/or DTCs. In addition to following normal Workshop Manual (WSM) diagnostics, inspect C105, an inline connector next to the right side valve cover, for signs of pushed out terminals, terminal damage, or harness damage. If any pushed out terminals, terminal damage, or harness damage is found, repair as necessary.
L3-FSV-326
Technical Instruction to Add Lock Washers to Closeout Panel Screws.
L3-FSV-318
Technical Instruction to Adjust Horn Orientation.
SB-15-02-01
Service Bulletin - Rear Lower Radius Rod Maintenance
L3-FSV-135_C
Technical Instruction to Adjust Ride Height.
L3-FSV-308
Technical Instruction to Retrofit D4-VDL-01 Data Logger.
L3-FSV-310
Technical Instruction to Install Program Change.
L3-FSV-306
Technical Instruction to Replace Coolant Valve.
FSV-284
NABI: THE CONTROLLERS ARE SHUTTING DOWN DUE TO ENGINE COOLING SYSTEM FANS FAILING AND WILL REPLACE MODINE GEN I CONTROLLER WITH MODINE GEN 2 CONTROLLER. *PE
L3-FSV-301
Technical Instruction to Adjust Steering Column Rubber Boot Dust Seal.
L3-FSV-302
Technical Instruction to Add Heat Shrink to Engine Shut Down in Radio Locker.
L3-FSV-303
Technical Instruction to Inspect JKA Ballast.
L3-FSV-304
Technical Instruction to Add Add Insuliner to CNG Fuel Line Conduit.
L3-FSV-224_A
TECHNICAL INSTRUCTION TO INSPECT REAR BULKHEAD SEAL.
L3-FSV-238_A
TECHNICAL INSTRUCTION TO INSPECT UNDERBODY FRAME PROTECTION.
L3-FSV-279
TECHNICAL INSTRUCTION TO INSPECT CONDENSOR DRAIN LINES.
L3-FSV-262
TECHNICAL INSTRUCTION TO RELOCATE AIR SYSTEM QUICK RELEASE (QR1) VALVE.
L3-FSV-263
TECHNICAL INSTRUCTION TO MODIFY STEERING COLUMN COSMETIC COVER.
L3-FSV-266
TECHNICAL INSTRUCTION TO ADD ISOLATION SEAL TO CNG FUEL LINE COVER ASSEMBLY.
L3-FSV-267
TECHNICAL INSTRUCTION TO ADJUST SHOCK ABSORBERS.
SU2013-1
Work Instruction - Sutrak - FMI Discharge Anaconda Line 1.
WI-077 REV 2
WORK INSTRUCTION - AGILITY - FIELD REPAIR - RUST TREATMENT
WI-077 REV 3
WORK INSTRUCTION - AGILITY - FIELD REPAIR - RUST TREATMENT
WI-080 REV1
WORK INSTRUCTION - AGILITY - FIELD REPAIR - SUPPORT CHANNELS AND BRACKETS
WI-081
WORK INSTRUCTION - AGILITY - FIELD REPAIR - R&R RUBBER STRIPS
L3-FSV-221
Technical Instruction to Modify CNG Tank Cradle Bolt.
L3-FSV-231
Technical Instruction to Remove plugs from Drain Holes in Frame.
WI-078
Work Instruction - Agility - Center Door Latches
L3-FSV-219
Technical Instruction to Relocate Brake Modulator Valve Remote Exhaust Outlet.
L3-FSV-224
Technical Instruction to Inspect Rear Bulkhead Seal.
L3-FSV-225
Technical Instruction to Replace CNG Front Cap Rubber Seal.
L3-FSV-214
Technical Instruction to Remove Kneeling Sensor.
L3-FSV-201
Technical Instruction to Adjust Driver's Seat Belt Retractor.
WI 112013
Work Instruction - Agility Systems - Field Inspection and Field Replacement of Lower Member CNG Fuel Tank Frame Brackets
SB-13-02-01
Service Bulletin - Brake Indicator Light.
WI-L3-FSV-142
NABI: A NEW, UPDATED COOLANT RECOVERY TANK WAS INSTALLED TO ENHANCE SERVICEABILITY FOR THE COOLING SYSTEM. MODEL BIRMINGHAM 31LFW-06, 283000. NO MODEL YEARS LISTED. *PE
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.