Vehicle report

2017 NISSAN ALTIMA

Compare every NISSAN ALTIMA yearNHTSA and EPA records

Service bulletins

235 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

NTB09-131C

Service Bulletin/Repair Instructions

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

NTB19-033G

Service Bulletin/Repair Instructions

INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual

NTB19-071D

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

NTB12-103I

Service Bulletin/Repair Instructions

CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-066C

Service Bulletin/Repair Instructions

CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-027D

Service Bulletin/Repair Instructions

CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-107G

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-127C

Service Bulletin/Repair Instructions

INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB09-081K

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028I

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-019H

Service Bulletin/Repair Instructions

WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-039R

Service Bulletin/Repair Instructions

DTC P17F0 OR P17F1 STORED IN THE TCM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB23-018G

Service Bulletin/Repair Instructions

NTB18-031F

Service Bulletin/Repair Instructions

NISSANCONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018F

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.

NTB17-039Q

Service Bulletin/Repair Instructions

CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

REV1 Altima_Sent

Service Bulletin/Repair Instructions

CVT Warranty Extension REVISION 1 Please discard earlier versions of this bulletin. The announcement from May 23, 2023 has been revised to include the following: â¢ The voucher program has been updated and the program rules and dealer instructions have been added to the FAQ section of this dealer announcement.

NTB08-097L

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

REVISION 4 PC861

Service Bulletin/Repair Instructions

Halogen Headlamp Voluntary Service Campaign REVISED August 18, 2023 Please discard earlier versions of this bulletin. The announcement from March 2, 2023 has been revised to include the following changes: â¢ Dealer headlamp support by email requests thru âFQA_Inspection_Support@nissan-usa.comâ for claim review will no longer be considered after September 23, 2023 ï See Claims Information, section 2 & 3

NTB23-018E

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018D

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-049

Service Bulletin/Repair Instructions

12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

NTB23-053

Service Bulletin/Repair Instructions

SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

Altima_Sentra_Ve

Service Bulletin/Repair Instructions

CVT Warranty Extension In an effort to assure customer satisfaction, demonstrate our confidence in continuously variable transmissions (CVTs), and to address customer concerns including those expressed by customers in the class actions, Nissan will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable) and reprogramming of the Transmission Control Module (TCM), on the vehicles listed in this announcement. The warranty is being extended from its original duration of 60 months/60,000 miles to 84 months/84,000 miles (whichever occurs first). Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissanâs New Vehicle Limited Warranty continue to apply. ***** What Dealers Should Do ***** 1. If an owner contacts a dealer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the customer of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension by excluding themselves from the class action settlement, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval using the VCAT tool. Please reference WBI/21-002. Control valves and CVT belt and pulley kits do not require pre-authorization for repairs made under warranty if they are within the dealerâs DCAL limit. 3. CVT warranty coverage can be confirmed using the warranty extensions/customer service initiatives page in Service Comm or DBS National Service History.

NTB17-039P

Service Bulletin/Repair Instructions

CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB12-103H

Service Bulletin/Repair Instructions

CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-107F

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB14-012I

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-003C

Service Bulletin/Repair Instructions

INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB23-018C

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB03-074Q

Service Bulletin/Repair Instructions

HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-031E

Service Bulletin/Repair Instructions

NISSANCONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055J

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018B

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018A

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-071C

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-145B

Service Bulletin/Repair Instructions

ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

REVISION 3 PC861

Service Bulletin/Repair Instructions

Halogen Headlamp Voluntary Service Campaign REVISED March 2, 2023 Please discard earlier versions of this bulletin. The announcement from September 16, 2022 has been revised to include the following changes: â¢ The parts restriction will be removed on the following parts and dealers will be able to order, as needed, via normal ordering process beginning March 9, 2023: ï 26060-3TA9A LAMP ASSY â HEAD (LH) (Headlamp Assembly) ï 26010-3TA9A Lamp ASSY â HEAD (RH) (Headlamp Assembly)

NTB09-081J

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028H

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB08-097K

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-126C

Service Bulletin/Repair Instructions

WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-101

Service Bulletin/Repair Instructions

DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.

NTB22-100

Service Bulletin/Repair Instructions

3G TELEMATICS HARDWARE DEACTIVATION SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Tâs 3G network connection, including Nissan Group, have had connectivity services affected. NissanConnectÂ® Services are no longer available on the APPLIED VEHICLES listed above.

NTB12-055I

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

REV 5 - 2013-18

Service Bulletin/Repair Instructions

Halogen Headlamp Warranty Extension REVISED September 27, 2022 Please discard earlier versions of this bulletin. The announcement from April 12, 2022 has been revised to include the following: â¢ The claims information section has been updated with parts ordering information: ï Parts must now be ordered using PC914. ï Parts orders using PC861 will no longer be accepted. Prior orders placed using PC861 will continue to be filled as parts become available.

NTB22-024B

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2013-2018 ALTIMA SEDAN; FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION Voluntary Service Campaign ID # PC861 is no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # PC861. ï· Discard all previous versions of NTB22-024.

PC861 2013-2018

Service Bulletin/Repair Instructions

Expiration Notification - Halogen Headlamp Voluntary Service Campaign ***** Dealer Announcement ***** On March 25, 2022 Nissan launched a Voluntary Service Campaign on certain MY2013-2018 Nissan Altima vehicles with halogen headlamps dimming due to delamination to support the settlement approved by the court presiding over the class action lawsuit. Customers that obtained approval by the Settlement Administrator were included in this VSC. Dealers were to inspect for delamination and, if necessary, replace both the right and left Halogen Headlamps. This customer service campaign and customer reimbursement for these repairs are no longer available under PC861. ***** What Dealers Should Do ***** 1. Service Comm will deactivate PC861 on any VINs that have not yet been inspected and/or repaired on September 23, 2022. 2. For vehicles that had halogen headlamp inspection under PC861 between May 20, 2022 and September 23, 2022, were diagnosed with no good (NG) condition but the repair was not completed due to parts not yet available will move to campaign ID PC890. a. For vehicles that had halogen headlamp inspection before May 20, 2022, were diagnosed with a no good (NG) condition and a dealer was not able to make claim, please email FQA_Inspection_Support@nissan-usa.com for claim processing support. 3. VINs will be noted with PC890 in Service Comm/NSH to allow future headlamp replacement as parts become available. 4. Dealers should use NTB22-039 to correct any vehicles subject to PC890. 5. Once repaired, dealers should submit the claim, using the appropriate claims coding provided for the action taken, and release the vehicle.

REVISION 2 PC861

Service Bulletin/Repair Instructions

Halogen Headlamp Voluntary Service Campaign REVISED September 16, 2022 Please discard earlier versions of this bulletin. The announcement from May 20, 2022 has been revised to include the following changes: Nissan has experienced an unexpected high volume of dealer orders for headlamp assemblies during this campaign. Nissan continues to work expeditiously with the supplier to improve the supply schedule in effort to fulfill DBS orders as quickly as possible. However, headlamp parts supply continues to be very limited for the foreseeable future. Nissan is requesting dealer support to reduce the impact across the network and ensure our customers are taken care of. Nissan is requesting dealers to review their current open parts orders, and is offering a limited opportunity to 1) cancel unnecessary orders and 2) return excess parts in dealer inventory. In the review, please consider future orders, as parts 26060-3TA90 & 26010-3TA9A will not be returnable (J-coded) after October 21, 2022. Nissan reserves the right to make changes to part returns at any time and is subject to change. Parts ordered under PC861 â¢ Dealers can cancel open DBS orders by contacting NNA Campaign Parts at nnacampaignparts@Nissan-Usa.com, and including the required dealer order information. â¢ Dealers can return any excess campaign parts using RFC âIâ-Code by the October 21, 2022 deadline and not affect your obsolescence accrual credit â¢ Parts 26060-3TA9A & 26010-3TA9A will not be returnable (J-coded) after October 21, 2022 Claims processing support â¢ Instruction for claims with inspection prior to May 20, 2022 (PC861); see item 2 under Claims Information section below o Requires work order with open date prior to May 20, 2022 with headlamp diagnosis NG

NTB14-012H

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

REVISION 1 PC861

Service Bulletin/Repair Instructions

Halogen Headlamp Voluntary Service Campaign REVISED May 20, 2022 Please discard earlier versions of this bulletin. The announcement from March 25, 2022 has been revised to include the following: â¢ Revised campaign claims procedure and new campaign ID, due to limited parts availability. See Claims Information section for more detail. â¢ Affected VIN population updated

NTB22-024A

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2013-2018 ALTIMA SEDAN; FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-039

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2013-2018 ALTIMA SEDAN; FRONT COMBINATION LAMPS (HEADLAMPS) INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2013- 2018 Altima sedan vehicles, to replace both combination lamp (headlamp) assemblies (Halogen only). This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC890 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.

NTB19-071B

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

REV 4 - 2013-18

Service Bulletin/Repair Instructions

Halogen Headlamp Warranty Extension REVISED April 12, 2022 Please discard earlier versions of this bulletin. The announcement from March 25, 2022 has been revised to include the following: â¢ The claims information section has been updated with information regarding vehicles whose warranty extension expired while waiting for parts.

NTB22-026

Service Bulletin/Repair Instructions

SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

REV 3 - 2013-18

Service Bulletin/Repair Instructions

Halogen Headlamp Warranty Extension REVISED March 25, 2022 Please discard earlier versions of this bulletin. The announcement from February 23, 2022 has been revised to include the following: â¢ The following parts have been placed on parts restriction. Dealers may place a SVC order for the parts listed below via DBS beginning March 25, 2022. Orders will be fulfilled in the order they were received. Existing CSC and VOR backorders will be filled, while STK (stock) backorders will be cancelled. ï 26060-3TA9A LAMP ASSY â HEAD (LH)(Headlamp Assembly) ï 26010-3TA9A LAMP ASSY â HEAD (RH)(Headlamp Assembly)

NTB22-024

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2013-2018 ALTIMA; FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2013-2018 Altima vehicles, to inspect and, if necessary, replace both combination (headlamp) assemblies (Halogen only). This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC861 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.

NTB17-039O

Service Bulletin/Repair Instructions

CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB15-049X

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

REV2 - 2013-18 A

Service Bulletin/Repair Instructions

Halogen Headlamp Warranty Extension REVISED February 23, 2022 Please discard earlier versions of this bulletin. The announcement from January 25, 2022 has been revised to include the following: â¢ If a customer requests inspection due to a visibility concern, dealers should determine eligibility using the warranty extension page of Service Comm. If eligible, refer to the repair bulletin to perform the necessary diagnostic inspection. o The Technical Service Bulletin has been updated to include an inspection procedure OP Code to support warranty claims processing.

NTB13-027C

Service Bulletin/Repair Instructions

CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-127B

Service Bulletin/Repair Instructions

NISSAN; INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB22-002A

Service Bulletin/Repair Instructions

2013-2018 ALTIMA; FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-097J

Service Bulletin/Repair Instructions

EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-082E

Service Bulletin/Repair Instructions

DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110Q

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-039N

Service Bulletin/Repair Instructions

PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB17-045C

Service Bulletin/Repair Instructions

CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB99-001F

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-077

Service Bulletin/Repair Instructions

DRIVERS POWER SEAT IS INOPERATIVE IF YOU CONFIRM The customer states that one or more of the driver (LH) seat controls are (or were) inoperative, AND/OR The windows, sunroof, sunshade and power mirrors are (or were) inoperative. NOTE: A no start condition may also be present. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Inspect the power seat switch wiring harness for damage. 2. Repair any damage found. 3. Install the rubber grommet listed in PARTS INFORMATION.

NTB18-031D

Service Bulletin/Repair Instructions

2016-2018 NISSANCONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on page 14. Please discard previous versions of this bulletin.

2013-18 Altima H

Service Bulletin/Repair Instructions

Halogen Headlamp Class Action Owner Notification Beginning October 25, 2021, current and former owners and lessees of certain 2013-2018 Altimas will receive a postcard from a Settlement Administrator informing them of the terms of a proposed class action that, subject to final court approval, could extend the warranty on the halogen headlamps. The class action lawsuit alleges that 2013-18 Altima models manufactured with halogen headlamps have a defect that causes the internal reflecting surface to delaminate, resulting in dimming of the low beam headlamps. Nissan denies all allegations of wrongdoing and liability but has agreed to this customer service initiative in order to resolve the dispute. Beginning in December 2018, all genuine Nissan replacement parts were manufactured with a new design. The proposed settlement is still subject to final approval by the court presiding over the class action lawsuit. The court will determine if the settlement will be approved at or shortly after a hearing that is scheduled for December 20, 2021. If approved, the warranty extension will become effective 31 days after the approval is granted. Additional communication will be distributed prior to the warranty extension going into effect. To be clear, unless and until the proposed settlement is approved by the presiding court, there is no warranty extension and you should proceed with halogen headlamp-related claims as outlined below in #3 under what dealers should do. The proposed settlement, and the associated potential warranty extension, include many terms and conditions. Rather than attempting to address questions about the proposed settlement terms from customers, it is strongly recommended that you refer customers to the websites and/or telephone numbers listed below so that they can receive information from appropriate sources and to avoid providing incorrect and/or incomplete information.

NTB18-055E

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055H

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-077D

Service Bulletin/Repair Instructions

SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-028D

Service Bulletin/Repair Instructions

INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-118B

Service Bulletin/Repair Instructions

NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Altima Maxima Lo

Service Bulletin/Repair Instructions

Rear Lower Suspension Link Warranty Extension Dealer Notification In October 2019, Nissan launched a Voluntary Service Campaign (P9324) on MY2013 Nissan Altima vehicles registered in high road-salt-usage states (Connecticut, Delaware, Iowa, Illinois, Indiana, Kentucky, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, Washington D.C., West Virginia and Wisconsin). In the interest of customer satisfaction, Nissan is providing a warranty extension to certain MY2013 Nissan Altima vehicles that were not included in P9324 and certain MY2014-2018 Nissan Altima and MY2016-2018 Nissan Maxima vehicles in all states. On some affected vehicles, one of the rear lower suspension links may corrode and separate at the bushing joint area. Customers may notice a knocking or rattling noise from the rear of the vehicle or observe wheel misalignment on the rear wheel(s) if the link separates. Owners of eligible vehicles will receive a notification indicating their eligibility for the following: â¢Warranty extension for the rear lower suspension links of 84 months and unlimited miles to their current 36 month/36,000 mile New Vehicle Limited Warranty for a total of 120 months warranty coverage (without regard to mileage). â¢This warranty extension will allow for a one-time replacement of the rear lower suspension links with new parts and a four-wheel alignment if parts are cracked or broken. Voluntary Service Campaign (P9324) on MY2013 Nissan Altima vehicles registered in high road-salt-usage states will continue. What Dealers Should Do: 1.Verify if vehicles are eligible for this Warranty Extension using the warranty extension page of Service Comm. 2.Dealers should remedy any eligible vehicles subject to this warranty extension to ensure customer satisfaction using Technical Field Bulletin NTB21-045.

NTB21-045

Service Bulletin/Repair Instructions

2013-2018 ALTIMA AND 2016-2018 MAXIMA; REAR SUSPENSION LOWER LINK IF YOU CONFIRM The customer experiences a knocking or rattling noise from the rear of the vehicle, Or The rear wheel and tire assemblies have a large amount of positive camber. ACTION Replace both rear lower links.

NTB16-018D

Service Bulletin/Repair Instructions

MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

NTB15-049W

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-008A

Service Bulletin/Repair Instructions

ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-106G

Service Bulletin/Repair Instructions

CORRECT OPERATION OF AUDIO CONTROLS AND BACK-UP CAMERA REQUIRES CONFIGURATION WITH C-III PLUS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB17-118A

Service Bulletin/Repair Instructions

NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-127A

Service Bulletin/Repair Instructions

NISSAN; INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB13-099G

Service Bulletin/Repair Instructions

AUDIO UNIT REPLACEMENT - VEHICLES WITH COLOR DISPLAY AUDIO AND NAVIGATION SYSTEM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin

NTB15-077C

Service Bulletin/Repair Instructions

NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-028C

Service Bulletin/Repair Instructions

INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-014A

Service Bulletin/Repair Instructions

BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

NTB19-071A

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-013f

Service Bulletin/Repair Instructions

NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin is no longer active. Please discard previous versions of NTB15-013. Refer to the ESM for the fluid cooler cleaning procedure.

NTB16-110p

Service Bulletin/Repair Instructions

NTB17-039m

Service Bulletin/Repair Instructions

NTB99-001e

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-031c

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on page 9. Please discard previous versions of this bulletin.

NTB15-049v

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-039l

Service Bulletin/Repair Instructions

NTB20-076

Service Bulletin/Repair Instructions

2021 ALTIMA WITH PR25DD ENGINE; NO ENGINE COVER SERVICE INFORMATION The APPLIED VEHICLE is not equipped with an engine cover. DO NOT file a warranty claim for a missing engine cover.

NTB17-039k

Service Bulletin/Repair Instructions

PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of these DTCs is stored: ï· P17F0 (CVT_JUDDER (T/M INSPECTION)) ï· P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: ï If a transmission judder (as described above) is not reported, this bulletin does not apply. ï If either P17F0 or P17F1 are not stored, this bulletin does not apply. ï If any DTCs are stored other than P17F0 or P17F1, this bulletin does not apply. ï NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTION ï· Refer to the Repair Flow Chart on page 2 for CVT repair. CAUTION: Always handle the CVT and component assemblies carefully and with the appropriate lifting tools.

NTB15-049u

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110o

Service Bulletin/Repair Instructions

NTB17-039j

Service Bulletin/Repair Instructions

NTB18-055d

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-039i

Service Bulletin/Repair Instructions

NTB16-110n

Service Bulletin/Repair Instructions

NTB15-049t

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055g

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-045b

Service Bulletin/Repair Instructions

MIL ON WITH DTC P0087, P0101, P0448, OR P2008, VEHICLES REGISTERED OUTSIDE OF CALIFORNIA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-115a

Service Bulletin/Repair Instructions

VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9345, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.

P9328_P9343_P934

Service Bulletin/Repair Instructions

Engine Control Module (ECM) Reprogram California Voluntary Emissions Service Campaign ***** Campaign Summary***** Nissan is conducting a Voluntary Emissions Service Campaign on approximately 104,221 specific Nissan vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or âSmog Checkâ test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. ï· P9328 â Affected Model Year 2015 ï· P9343 â Affected Model Year 2016 ï· P9345 â Affected Model Year 2017 ï· P9347 â Affected Model Year 2018 ï· P9349 â Affected Model Year 2019 2. Dealers should remedy any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction.

NTB19-115

Service Bulletin/Repair Instructions

VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9435, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.

NTB15-013e

Service Bulletin/Repair Instructions

NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-039h

Service Bulletin/Repair Instructions

NTB16-085b

Service Bulletin/Repair Instructions

ENHANCED DIAGNOSTIC LOGIC FOR CVT This bulletin has been superseded by NTB17-039. Please discard previous versions of this bulletin.

NTB17-039g

Service Bulletin/Repair Instructions

NTB16-110m

Service Bulletin/Repair Instructions

NTB19-045a

Service Bulletin/Repair Instructions

MIL ON WITH DTC P0087, P0101, P0448, OR P2008 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-072

Service Bulletin/Repair Instructions

TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch of the APPLIED VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. ï· Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.

NTB19-071

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.

NTB19-006a

Service Bulletin/Repair Instructions

2015-2017 ALTIMA WITH 4-CYL ENGINE; EXHAUST LEAK FROM EXHAUST MANIFOLD This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB14-012e

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-049s

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-045

Service Bulletin/Repair Instructions

MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has a stored DTC shown in Table A on the next page, AND The ECM part number is shown in Table B, starting on page 3. ACTION First, perform the appropriate diagnostic procedure for the stored code to repair the vehicle according to the Electronic Service Manual (ESM), AND Reprogram the ECM after performing the diagnosis and repair.

NTB18-019a

Service Bulletin/Repair Instructions

2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB14-060c

Service Bulletin/Repair Instructions

ABNORMAL NOISE FROM FRONT ENGINE MOUNT SERVICE INFORMATION A two-piece design front engine mount is currently being used for the Applied Vehicles listed. A single thunk noise may be heard during the first few accelerations of the day from this type of mount, and is considered normal operation. The mount has also been designed with built-in free play that is normal. Under normal driving conditions: - A thunk noise may be heard during the first few accelerations of the day, And - Does not occur again, or at any other time. DO NOT REPLACE THE MOUNT: - If it has free play or a ?single event? thunk sound during the first few accelerations of the day. This is considered a normal characteristic of this type of engine mount. - Allowable free play (vertical movement) is 5 mm. - If a shift shock condition is present when shifting from Park into gear or between any combination of gears. This condition is due to transmission line pressure and not movement of the mount. - If a whistle type noise is heard. This is caused by a disconnected vacuum line. NOTE: Refer to the appropriate section of the Electronic Service Manual (ESM) related to transaxles for further diagnostic information on shift shock. Warranty claims for front engine mount replacement due to a whistle noise or a mount that has 5 mm or less free play will be denied.

NTB18-055c

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-030

Service Bulletin/Repair Instructions

2016-2018 NISSAN; MIL ON WITH DTC P0171, P0174, P2097, AND/OR P2099 This bulletin applies to Altima vehicles equipped with VQ35 engine only. IF YOU CONFIRM The MIL is ON with one or more of the following Air/Fuel (A/F) Sensor DTCs stored: - P0171 (Fuel Injection System Function) - P0174 (Fuel Injection System Function) - P2097 (A/F SENSOR 1) - P2099 (A/F SENSOR 1) ACTION 1. Perform the appropriate diagnostic procedure outlined in the Electronic Service Manual (ESM). 2. Refer to Table A on page 2 and page 3 to confirm if Electronic Control Module (ECM) reprogramming is needed.

NTB12-100b

Service Bulletin/Repair Instructions

CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-103g

Service Bulletin/Repair Instructions

NTB15-102b

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; WHINE NOISE FROM CVT AT HIGHWAY SPEEDS This bulletin applies only to vehicles equipped with a QR25DE (4-cyl) engine. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB18-055b

Service Bulletin/Repair Instructions

NTB19-022

Service Bulletin/Repair Instructions

NISSAN; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.

NTB19-021

Service Bulletin/Repair Instructions

NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.

NTB16-028b

Service Bulletin/Repair Instructions

INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110L

Service Bulletin/Repair Instructions

NTB13-097g

Service Bulletin/Repair Instructions

ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB15-049r

Service Bulletin/Repair Instructions

NTB17-082b

Service Bulletin/Repair Instructions

NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB19-006

Service Bulletin/Repair Instructions

2015-2017 ALTIMA WITH 4-CYL ENGINE; EXHAUST LEAK FROM EXHAUST MANIFOLD IF YOU CONFIRM An exhaust leak is coming from the exhaust manifold AND A crack is found in the exhaust manifold. - See page 2, Figure 1. ACTION Replace the exhaust manifold and exhaust tube. - For 2015-2016 Altima: Refer to the Electronic Service Manual (ESM), sections EMEngine Mechanical and EX-Exhaust System, for exhaust manifold and exhaust tube replacement procedures, respectively. - For 2017 Altima: Refer to the ESM, section ENGINE / ENGINE MECHANICAL / QR25DE and ENGINE / EXHAUST SYSTEM / QR25DE, for exhaust manifold and exhaust tube replacement procedures, respectively.

NTB16-110k

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813 OR P0841 STORED This bulletin applies only to vehicles equipped with a 4 cylinder engine. This bulletin has been amended. Please see amendment history on the last page. Please discard previous versions of this bulletin.

NTB17-030a

Service Bulletin/Repair Instructions

NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

Revision 1-NEVAP

Service Bulletin/Repair Instructions

OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

NTB18-080

Service Bulletin/Repair Instructions

AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

NTB12-103f

Service Bulletin/Repair Instructions

CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-055a

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110j

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776 OR P0841 STORED This bulletin has been amended. Please see amendment history on the last page. Please discard previous versions of this bulletin.

NTB15-077b

Service Bulletin/Repair Instructions

NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB17-040b

Service Bulletin/Repair Instructions

REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended to add 2018-2019 Kicks. Please discard previous versions of this bulletin.

NTB15-049q

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

NTB13-077d

Service Bulletin/Repair Instructions

CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

NTB15-049p

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

NTB18-055

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each dealer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.

NTB18-017b

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.

PC633 PM827 P832

Service Bulletin/Repair Instructions

CAMPAIGN BULLETIN Engine Control Module (ECM) Reprogram Regional (NV & AZ) Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a Regional Voluntary Service Campaign to reprogram the Engine Control Module (ECM) on affected vehicles currently registered in Nevada and Arizona. The current programming may cause the air/fuel ratio to become excessively rich resulting in engine stop under certain high temperature and high altitude conditions. In addition, Nissan is asking dealers to inspect and, if necessary, replace the Positive Crankcase Ventilation (PCV) valve on certain 2013-14 Nissan Sentra vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History - Open Campaign I.D. Due to the various models involved and the associated responsible manufacturing location of origin, there are three (3) separate campaign IDs with unique Campaign Bulletins for each model: - PC633 - PM827 - P8325 New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information NOTE: These campaigns are state-specific and limited to vehicles that are currently registered, or previously registered, in the state of Nevada or Arizona only. 2. Nissan requests dealers repair any affected vehicles in retailer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use the appropriate repair bulletin for the applicable model as listed below to correct any vehicles subject to this campaign. 4. Once repaired, dealer should submit a warranty claim and release the vehicle.

NTB18-048

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2013-2017 ALTIMA ENGINE CONTROL MODULE REPROGRAM This bulletin applies only to vehicles equipped with a 4-cylinder engine. INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2013-2017 Altima vehicles that are currently registered in the States of Arizona or Nevada. The Engine Control Module (ECM) software will be reprogrammed. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC633 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.

NTB16-110i

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR P0841 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin has been amended to add additional information under If You Confirm on page 1, the Claims Information and to add part numbers to Table B. No other changes have been made.

NTB13-054d

Service Bulletin/Repair Instructions

ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. Table A on page 5 has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-031b

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. The IF YOU CONFIRM section and software number has changed. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-006

Service Bulletin/Repair Instructions

2016-2018 ALTIMA WITH QR25DE/4-CYL ENGINE; MOAN NOISE AFTER A/C COMPRESSOR ENGAGES This bulletin applies only to vehicles equipped with a 4-cylinder engine. IF YOU CONFIRM A moan type noise is heard just after the A/C is turned ON (compressor engages) and lasts for about 10 seconds and/or While the A/C is operating and the compressor clutch cycles from OFF to ON, the moan noise is heard for about 10 seconds. ACTION Replace the low pressure A/C flex hose with the one listed in PARTS INFORMATION. Do NOT replace the compressor for this incident, if it should occur. This bulletin does not apply for compressor clutch locked, squeal noises, or any other A/C malfunctions.

NTB18-031a

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. This bulletin has been amended to correct Bosch contact information on page 2. No other changes have been made. Please discard previous versions of this bulletin.

NTB13-054c

Service Bulletin/Repair Instructions

ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. Table A on page 6 has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-031

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. IF YOU CONFIRM One or more of the following is occurring: - The navigation unit intermittently reboots: - At random or while listening to SXM or on a Bluetooth hands-free phone call. - Loud booming noise from speakers while on a Bluetooth hands-free call. - Navigation unit screen illumination does not change at night as designed. - AM/FM signal strength issues. - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. AND - The Software version has been confirmed as ?needs update? (refer to page 4). ACTION - Perform the SERVICE PROCEDURE starting on page 3 and reprogram the Navigation system with USB memory stick shown below.

NTB03-074m

Service Bulletin/Repair Instructions

FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.

NTB14-053b

Service Bulletin/Repair Instructions

2014-2018 ALTIMA; HYDRAULIC ELECTRIC POWER STEERING SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

NTB16-018c

Service Bulletin/Repair Instructions

MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-029

Service Bulletin/Repair Instructions

2013-2018 ALTIMA; AFTERMARKET HEADLIGHTS SERVICE INFORMATION If a headlight housing assembly on an applied vehicle needs to be replaced for any reason, note the following: - Only Original Equipment (O.E.) components are warrantable though Nissan. - Aftermarket components are not warrantable through Nissan. - Confirm that it is a genuine Nissan part before submitting a Warranty Claim. - Genuine Nissan headlight housings, on an applied vehicle, will have "Nissan" and "NAL" markings on the housing. - See examples of an O.E. headlight housing assembly (Figure 1 on page 2) and aftermarket headlight housing assembly (Figure 2 on page 3). NOTE: The Nissan New Vehicle Limited Warranty does not cover aftermarket components. Refer to the Nissan Assurance Products Resource Manual (APRM) for guidelines on warranty coverage. The vehicle Owner's Manual contains the complete details regarding the limited warranty.

NTB13-107b

Service Bulletin/Repair Instructions

INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.

NTB18-017a

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.

NTB11-044c

Service Bulletin/Repair Instructions

WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

NTB16-110h

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies only to Altima vehicles equipped with a 4 cylinder engine. This bulletin has been amended to add additional information under NOTE on page 1. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-039f

Service Bulletin/Repair Instructions

NTB17-039e

Service Bulletin/Repair Instructions

PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies only to vehicles equipped with a V6 engine. This bulletin has been amended to add Quest to Applied Vehicles and information related to Quest on pages 25, 100, 102, 103 and 105. Please discard previous versions of this bulletin. IMPORTANT: You must read the entire bulletin to properly perform this repair.

NTB18-019

Service Bulletin/Repair Instructions

2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS SERVICE INFORMATION A new Engine Support Tool and Engine Support Bracket are now available to allow the CVT to be removed from the Applied Vehicles without having to remove the engine. The procedures in this bulletin are different than those that are currently in the Electronic Service Manual (ESM), which will be updated with this information at a later date. Please refer to the vehicle specific service procedure to use these new tools: Altima Page 2 Rogue AWD Page 11 Rogue FWD Page 24

NTB18-017

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.

NTB15-049o

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.

NTB18-008

Service Bulletin/Repair Instructions

ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin applies only to vehicles equipped with Automatic Emergency Braking (AEB) or Forward Emergency Braking (FEB). SERVICE INFORMATION If the following ICC/ADAS codes are stored, make sure to follow the diagnostic procedures in the Electronic Service Manual (ESM) before replacing any parts. C1A03 ? VEHICLE SPEED SENSOR -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1A04 ? ABS/TCS/VDC SYSTEM -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1B01 CAM AIMING INCMP -The diagnostic procedure in the ESM includes check and, if needed, repair for LANE CAMERA DTCs before replacing ADAS components. -LANE CAMERA DTC may require adjustment of the lane camera. -If repairs/adjustments are performed for the Lane Camera; when compete, perform DTC Confirmation Procedure again before doing any additional repairs.

NTB13-054b

Service Bulletin/Repair Instructions

ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. The APPLIED VEHICLES section and Table A on pages 5 and 6 have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-049n

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a TCU (Telematics Communication Unit). This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.

NTB16-110g

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a 4-cyl engine only. This bulletin has been amended to add 2013-2014 Altima to the Applied Vehicles and Table A on page 80, and to supersede NTB15-084 and NTB15-086. The Service Procedure was updated on page 81. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-127

Service Bulletin/Repair Instructions

NISSAN; INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE SERVICE INFORMATION When the initialization procedure being performed with a new or existing Intelligent Key to an applied vehicle is interrupted (the procedure stops or will not continue), the BCM may be left in learn mode and will not function until it returns to normal mode. Under this condition, the BCM and Intelligent Key(s) will not function normally. If this condition occurs, the BCM must be returned to normal mode and the initialization procedure started over. To get back to the beginning of the Initialization procedure, use one of the following procedures: - Successfully perform the initialization procedure using one of the original Intelligent Keys twice consecutively. - Each successful initialization will follow with two (2) quick tones. OR - When the initialization procedure cannot be successfully performed twice (more than two quick tones), perform the initialization procedure five (5) times using the inoperative ?failed? Intelligent Key. - Initialization does not need to be successful when performed five times. When returning to normal operating mode, the initialization procedure for all Intelligent Keys may be started again.

NTB16-117b

Service Bulletin/Repair Instructions

2016-2017 ALTIMA; MIL ON WITH A/F RATIO SENSOR DTC(s) This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard all previous versions of this bulletin.

NTB17-118

Service Bulletin/Repair Instructions

NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin applies to vehicles equipped with Intelligent Key only. SERVICE INFORMATION When replacing or adding an Intelligent Key, it is very important to make sure the correct Intelligent Key is selected from the parts department. - A running change was made that will help identify the correct Intelligent Key. - Beginning in late 2017 and early 2018 the last five digits of the Intelligent Key part number is marked on the Intelligent Key under the mechanical key. - See page 2 for location images of this part number addition. NOTE: - A correct Intelligent Key may or may not have the last five digits of the part number as shown on page 2. - The above running change was applied as a ?help? to identify the correct Intelligent Key for a given vehicle, but the actual part number listed in the parts catalog did not change. - Make sure to use the electronic parts catalog (FAST) or equivalent to confirm the correct Intelligent Key for a given vehicle.

NTB17-040a

Service Bulletin/Repair Instructions

REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended to add 2018 Versa Sedan and 2018 Versa Note. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-049m

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with a wireless communication device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.

NTB16-110f

Service Bulletin/Repair Instructions

2015-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles with a 4 cylinder engine only. This bulletin has been amended. Changes were made on pages 2, 3, 85-89 and 96. Please discard previous versions of this bulletin. You must read the entire bulletin to properly perform this repair; includes TCM reprograming.

NTB16-110e

Service Bulletin/Repair Instructions

2015-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a 4-cylinder engine only. This bulletin has changed. You must read the entire bulletin to properly perform this repair. Please discard previous versions of this bulletin.

NTB17-039c

Service Bulletin/Repair Instructions

PATHFINDER, ALTIMA, MAXIMA, MURANO; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a V6 engine only. This bulletin has changed. You must read the entire bulletin to properly perform this repair. Please discard previous versions of this bulletin.

NTB17-039d

Service Bulletin/Repair Instructions

PATHFINDER, ALTIMA, MAXIMA, MURANO; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a V6 engine only. This bulletin has been amended to change the parts table information on page 101. Please discard previous versions of this bulletin. IMPORTANT: You must read the entire bulletin to properly perform this repair.

NTB15-049L

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-107

Service Bulletin/Repair Instructions

2016-2017 MAXIMA AND ALTIMA; POP/CLUNK NOISE FROM REAR WHEN DRIVING OVER BUMPS This bulletin applies to SR trim level Altima vehicles. IF YOU CONFIRM A pop or clunk noise from the rear of the vehicle, especially when driving over bumps, AND The rear suspention connecting rod nuts are found to be loose on the left and/or right side. ACTION Replace the connecting rod and nuts on the left and/or right side with the ones listed in Parts Information.

NTB11-044b

Service Bulletin/Repair Instructions

NTB16-110D

Service Bulletin/Repair Instructions

2015-2017 ALTIMA; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies only to Altima vehicles equipped with a 4-cylinder engine. This bulletin has been amended to change the If You Confirm, Repair Flow Chart information and Figures 10G, 3I and 4I. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-064a

Service Bulletin/Repair Instructions

2013 ? 2017 ALTIMA AND PATHFINDER; SHIFT LOCK SOLENOID REMOVAL AND INSTALLATION This bulletin has been amended to change the PFP in the Claims Information. Please discard all previous versions of this bulletin.

NTB15-049k

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. The Applied Vehicles section has been revised and TCU Configuration section has been added. No other changes have been made. Please discard previous versions of this bulletin.

NTB13-077c

Service Bulletin/Repair Instructions

CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

NTB17-082a

Service Bulletin/Repair Instructions

NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-008b

Service Bulletin/Repair Instructions

NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima Sedan, Pathfinder and Murano vehicles with a 6-cylinder engine and Titan/Titan XD vehicles with a V8 gasoline engine. This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-090

Service Bulletin/Repair Instructions

DTC P0036 DIAGNOSTIC INFORMATION This bulletin applies only to Altima and Pathfinder vehicles with a 6-cylinder engine. SERVICE INFORMATION The Electronic Service Manual (ESM) information for DTC P0036 may be inaccurate or incomplete for the Applied Vehicles. If an Applied Vehicle stores a DTC P0036, follow diagnostic procedures in the ESM for Bank 2 A/F Sensor Heater open or shorted.

NTB17-091

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; MIL ON WITH DTC P2004 STORED IF YOU CONFIRM MIL is ON with P2004 (INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR) stored. And There are no drivability issues. ACTION 1. Remove the intake manifold. 2. Replace the intake manifold runner control valve position sensor. 3. Re-install intake manifold.

NTB14-060b

Service Bulletin/Repair Instructions

THUNK SOUND ON FIRST FEW ACCELERATIONS OF THE DAY This bulletin applies only to Altima, Murano, and Pathfinder vehicles equipped with 6-cylinder engine. This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.

NTB16-112a

Service Bulletin/Repair Instructions

2013-2017 ALTIMA; A/C DOES NOT BLOW COLD AND CLUTCH DOES NOT ENGAGE This bulletin has been amended. The Title and APPLIED VEHICLES section have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB14-053a

Service Bulletin/Repair Instructions

2014-2017 ALTIMA; HYDRAULIC ELECTRIC POWER STEERING SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised and information on page 10 has been added. No other changes have been made. Please discard previous versions of this bulletin.

NTB12-055f

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-064

Service Bulletin/Repair Instructions

2013 ? 2017 ALTIMA AND PATHFINDER; SHIFT LOCK SOLENOID REMOVAL AND INSTALLATION SERVICE INFORMATION If an Applied Vehicle needs the shift lock solenoid replaced for any reason, use the Service Procedure in this bulletin.

NTB16-110c

Service Bulletin/Repair Instructions

2015-2017 ALTIMA; 4 CYLINDER WITH DTC P0776 STORED This bulletin applies only to 4 cylinder models. This bulletin has been amended to add model years to Applied Vehicles, to change Figure 10G on page 53 and to change footnote 2 on page 80. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-015h

Service Bulletin/Repair Instructions

PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended to remove 2013-2014 Pathfinder from applied vehicles. No other changes have been made. Please discard all previous versions of this bulletin.

NTB12-103e

Service Bulletin/Repair Instructions

CVT / TCM CALIBRATION DATA "WRITE" PROCEDURE This bulletin does not apply to Pathfinder Hybrid, Murano Hybrid or Rogue Hybrid This bulletin has been amended. APPLIED VEHICLES has been updated. SERVICE INFORMATION has been amended. A REPAIR TABLE has been added. Procedural steps have been added to SERVICE PROCEDURE. Discard all previous versions of this bulletin.

NTB15-013d

Service Bulletin/Repair Instructions

NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-008a

Service Bulletin/Repair Instructions

NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies to vehicles equipped with 6-cylinder engines. For Titan and Titan XD, this bulletin applies only vehicles equipped with gasoline engines. This bulletin has been amended in the PARTS INFORMATION and CLAIMS INFORMATION sections. Discard previous versions of this bulletin.

NTB17-040

Service Bulletin/Repair Instructions

REVISED WHEEL ALIGNMENT SPECIFICATIONS SERVICE INFORMATION For the Applied Vehicles, some wheel alignment specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the Electronic Service Manual (ESM) have been revised. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the corrected specifications listed in this bulletin.

NTB15-015g

Service Bulletin/Repair Instructions

PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended to add applied vehicles and change the Parts Information. No other changes have been made. Please discard all previous versions of this bulletin.

NTB16-085a

Service Bulletin/Repair Instructions

ENHANCED DIAGNOSTIC LOGIC FOR CVT This bulletin has been amended to add model years to the Applied Vehicles and part numbers to Table A. No other changes have been made. Please discard all previous versions of this bulletin.

NTB17-030

Service Bulletin/Repair Instructions

NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

NTB14-068b

Service Bulletin/Repair Instructions

POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.

NTB17-008

Service Bulletin/Repair Instructions

NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima, Pathfinder and Murano vehicles equipped with V6 engine OR Titan/Titan XD equipped with VK56 engine IF YOU CONFIRM Engine oil is leaking from a valve timing control solenoid valve, And The valve timing control solenoid valve operates correctly and is not externally damaged. ACTION Replace the valve timing control solenoid valve O-ring with a new one using the Service Procedure starting on page 2.

PC502 - 2017 Alt

Service Bulletin/Repair Instructions

Front Member Welds ***** Detailed Information ***** On October 26, 2016, Nissan announced a Quality Assurance Hold certain MY2017 Altima (L33) and MY2017 Maxima (A36) vehicles. A repair procedure, parts, and tools are now available to repair these vehicles. Nissan is requesting that dealers enhance the front member weld on affected vehicles using the procedure included with this announcement. The quality hold can be released once the procedure has been performed. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this inventory service action using Service Comm I.D. PC502. - New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information 2. Use the attached procedure to repair the affected Altima and Maxima front member welds. - Nissan has developed an automatic parts shipment plan to ship parts and essential tools (J-52384 - Manual Rivet Gun & J-52385 - Protective Shield) to dealers with affected inventory. - Shipments will begin arriving at dealers on January 27th, 2017. 3. Dealers are requested to remedy any affected vehicle in dealer new or pre-owned inventory prior to sale to ensure customer satisfaction. NOTE: Only dealer inventory units are active in Service Comm at this time. If a retailed vehicle is identified in Service Comm, no action is necessary at this time. Dealers may request a manual campaign closure by emailing campaign_manual_closure@nissan-usa.com and providing the following information: - Customer?s VIN: - Dealer Number: - Campaign ID: Note: If a vehicle previously held and sold, there is no need to notify the customer at this time. If necessary, Nissan will contact affected customers.

PC514 - 2016-17

Service Bulletin/Repair Instructions

ECM Reprogram Voluntary Emissions Service Campaign This bulletin applies only to vehciles equipped with 4 cylinder engine. ***** Campaign Summary***** Nissan is conducting a Voluntary Emissions Service Campaign on approximately 311,675 specific 2016-2017 model year Nissan Altima vehicles equipped with a 2.5L engine. Nissan has discovered that some model year 2016 and 2017 Altima vehicles are equipped with an improperly calibrated Engine Control Module (ECM) that may illuminate a Malfunction Indicator Light (MIL) for abnormal Air/Fuel (A/F) sensor output. The cause is a grille shutter calibration issue which may lead to higher than expected A/F sensor temperature, resulting in the MIL for delayed sensor response rate. To correct this condition, Nissan is conducting a Voluntary Emissions Service Campaign to reprogram the Engine Control Module (grille shutter opening logic) free of charge. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm I.D. PC514. 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB16-514 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.

NTB17-002

Service Bulletin/Repair Instructions

VOLUNTARY EMISSIONS SERVICE CAMPAIGN 2016-2017 ALTIMA ENGINE CONTROL MODULE REPROGRAM This bulletin applies only to vehicles equipped with 4-cylinder engines. INTRODUCTION Nissan is conducting a Voluntary Emissions Service Campaign on certain specific model year 2016 - 2017 Altima vehicles to reprogram the Engine Control Module (ECM). The reprogram will affect the operation of the grille shutters and will reduce under hood temperatures which, if not reprogrammed, could lead to a false Malfunction Indicator Lamp in some circumstances. The ECM will be reprogrammed at no charge to customers for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC514 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer?' responsibility to check Service Comm for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer?s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

NTB16-123

Service Bulletin/Repair Instructions

PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

NTB16-117a

Service Bulletin/Repair Instructions

2016-2017 ALTIMA; MIL ON WITH A/F RATIO SENSOR DTC(s) This bulletin applies only to models equipped with 4-cylinder engines. This bulletin has been amended. The Parts Information section has been corrected. Please discard previous versions of this bulletin.

NTB16-117

Service Bulletin/Repair Instructions

2016-2017 ALTIMA; MIL ON WITH A/F RATIO SENSOR DTC(s) IF YOU CONFIRM One or more of the following DTCs is stored: - P014C - A/F SENSOR1 (B1) (O2 sensor slow response - rich to lean bank 1 sensor 1) - P014D - A/F SENSOR1 (B1) (O2 sensor slow response - lean to rich bank 1 sensor 1) - P015A - A/F SENSOR1 (B1) (O2 sensor delayed response - rich to lean bank 1 sensor 1) - P015B - A/F SENSOR1 (B1) (O2 sensor delayed response - lean to rich bank 1 sensor 1) ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. If this bulletin applies: 2. Reprogram the ECM. 3. Replace the Air Fuel Ratio (A/F) Sensor 1. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB13-107a

Service Bulletin/Repair Instructions

INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.

NTB16-116

Service Bulletin/Repair Instructions

NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS

NTB15-049j

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. Information for 2017 Rogue and Rogue Hybrid has been applied. No other changes have been made. Please discard previous versions of this bulletin.

NTB13-077b

Service Bulletin/Repair Instructions

CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

Update - PC497 -

Service Bulletin/Repair Instructions

Front Member Welds - Quality Assurance Hold ***** Detailed Information ***** On October 14th, 2016, Nissan announced a Quality Assurance (QA) Hold on certain MY2017 Nissan Altima and Maxima vehicles identified in Service Comm as a precaution. Further investigation by Nissan confirmed the subject vehicles meet Nissan's standards and applicable regulations and require no further action. Accordingly, the Quality Assurance Hold is rescinded. IMPORTANT: Effective immediately, the Quality Assurance Hold is rescinded and the subject vehicles may be released for sale. ***** What Dealers Should Do ***** 1. Effective immediately, dealers may release for sale any vehicles in dealer inventory affected by this quality hold.

PC497 - 2017 Alt

Service Bulletin/Repair Instructions

Front Member Welds - Quality Assurance Hold ***** Detailed Information ***** Nissan is committed to a high level of customer service and satisfaction. This commitment requires Nissan to periodically place certain specific vehicles on a temporary Quality Assurance (QA) Hold to assure that these vehicles, as delivered to our customers, meet our exacting standards and our customers? expectations. Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on approximately 408 specific MY2017 Altima (L33) and 152 specific MY2017 Maxima (A36) vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this QA Hold using Service Comm I.D. PC497 Note: Dealers should continue to check new arriving inventory for QA Hold applicability. 2. Please do not drive, sell, or trade the specific 2017 Altima and Maxima vehicles in Dealer Inventory subject to this QA Hold. 3. No further action is necessary at this time. Nissan will provide an update by October 28th, 2016.

NTB15-049i

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION ONLY SPECIFIC TRIM PACKAGES ARE AFFECTED This bulletin has been amended. Information for 2017 Altima, Murano, Pathfinder, Sentra, and Titan/Titan XD vehicles has been applied. No other changes have been made. Please discard previous versions of this bulletin.

PC495 2016-17 Al

Service Bulletin/Repair Instructions

CAMPAIGN BULLETIN - Accelerator Pedal ***** Detailed Information ***** Nissan is conducting a dealer inventory inspection on approximately 5,797 MY2016-17 Nissan Altima and 1,646 MY2017 Maxima vehicles to tighten the accelerator pedal mounting bolts to specification. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this inventory inspection using Service Comm I.D. PC495. 2. Use the attached repair procedure to tighten the accelerator pedal mounting bolts to specification. - If bolts are missing, please send the requested information to nnafqasupport@nissan-usa.com and await further instruction. 3. Submit the warranty claim, and release the vehicle. Note: Dealers should continue to check new arriving inventory for applicability. 4. Dealers are requested to inspect any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.

NTB13-097D

Service Bulletin/Repair Instructions

ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.

NTB15049H

Service Bulletin/Repair Instructions

SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnectSM Services subscription, the TCU communicates with the NissanConnectSM Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. See this bulletin for further detail.

NTB15043

Service Bulletin/Repair Instructions

SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.

NTB14032

Service Bulletin/Repair Instructions

SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.