Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB15-049CC
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION HINT: This bulletin applies to vehicles equipped with a 4G network compatible TCU. TCUs compatible with 3G network only are no longer supported. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the NissanConnect® Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. · A table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. · A CHECK-OFF SHEET has been provided on page 20 to print and check off steps as they are performed. Staple the completed CHECK-OFF SHEET to the repair order.
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB12-103I
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-127C
Service Bulletin/Repair Instructions
INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039R
Service Bulletin/Repair Instructions
DTC P17F0 OR P17F1 STORED IN THE TCM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB15-049AA
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039Q
Service Bulletin/Repair Instructions
CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
REV1 Altima_Sent
Service Bulletin/Repair Instructions
CVT Warranty Extension REVISION 1 Please discard earlier versions of this bulletin. The announcement from May 23, 2023 has been revised to include the following: ⢠The voucher program has been updated and the program rules and dealer instructions have been added to the FAQ section of this dealer announcement.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REVISION 4 PC861
Service Bulletin/Repair Instructions
Halogen Headlamp Voluntary Service Campaign REVISED August 18, 2023 Please discard earlier versions of this bulletin. The announcement from March 2, 2023 has been revised to include the following changes: ⢠Dealer headlamp support by email requests thru âFQA_Inspection_Support@nissan-usa.comâ for claim review will no longer be considered after September 23, 2023 ï See Claims Information, section 2 & 3
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
Altima_Sentra_Ve
Service Bulletin/Repair Instructions
CVT Warranty Extension In an effort to assure customer satisfaction, demonstrate our confidence in continuously variable transmissions (CVTs), and to address customer concerns including those expressed by customers in the class actions, Nissan will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable) and reprogramming of the Transmission Control Module (TCM), on the vehicles listed in this announcement. The warranty is being extended from its original duration of 60 months/60,000 miles to 84 months/84,000 miles (whichever occurs first). Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissanâs New Vehicle Limited Warranty continue to apply. ***** What Dealers Should Do ***** 1. If an owner contacts a dealer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the customer of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension by excluding themselves from the class action settlement, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval using the VCAT tool. Please reference WBI/21-002. Control valves and CVT belt and pulley kits do not require pre-authorization for repairs made under warranty if they are within the dealerâs DCAL limit. 3. CVT warranty coverage can be confirmed using the warranty extensions/customer service initiatives page in Service Comm or DBS National Service History.
NTB17-039P
Service Bulletin/Repair Instructions
CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB12-103H
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-071C
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
REVISION 3 PC861
Service Bulletin/Repair Instructions
Halogen Headlamp Voluntary Service Campaign REVISED March 2, 2023 Please discard earlier versions of this bulletin. The announcement from September 16, 2022 has been revised to include the following changes: ⢠The parts restriction will be removed on the following parts and dealers will be able to order, as needed, via normal ordering process beginning March 9, 2023: ï 26060-3TA9A LAMP ASSY â HEAD (LH) (Headlamp Assembly) ï 26010-3TA9A Lamp ASSY â HEAD (RH) (Headlamp Assembly)
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-009L
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049Z
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB15-049Y
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REV 5 - 2013-18
Service Bulletin/Repair Instructions
Halogen Headlamp Warranty Extension REVISED September 27, 2022 Please discard earlier versions of this bulletin. The announcement from April 12, 2022 has been revised to include the following: ⢠The claims information section has been updated with parts ordering information: ï Parts must now be ordered using PC914. ï Parts orders using PC861 will no longer be accepted. Prior orders placed using PC861 will continue to be filled as parts become available.
NTB22-024B
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013-2018 ALTIMA SEDAN; FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION Voluntary Service Campaign ID # PC861 is no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # PC861. ï· Discard all previous versions of NTB22-024.
PC861 2013-2018
Service Bulletin/Repair Instructions
Expiration Notification - Halogen Headlamp Voluntary Service Campaign ***** Dealer Announcement ***** On March 25, 2022 Nissan launched a Voluntary Service Campaign on certain MY2013-2018 Nissan Altima vehicles with halogen headlamps dimming due to delamination to support the settlement approved by the court presiding over the class action lawsuit. Customers that obtained approval by the Settlement Administrator were included in this VSC. Dealers were to inspect for delamination and, if necessary, replace both the right and left Halogen Headlamps. This customer service campaign and customer reimbursement for these repairs are no longer available under PC861. ***** What Dealers Should Do ***** 1. Service Comm will deactivate PC861 on any VINs that have not yet been inspected and/or repaired on September 23, 2022. 2. For vehicles that had halogen headlamp inspection under PC861 between May 20, 2022 and September 23, 2022, were diagnosed with no good (NG) condition but the repair was not completed due to parts not yet available will move to campaign ID PC890. a. For vehicles that had halogen headlamp inspection before May 20, 2022, were diagnosed with a no good (NG) condition and a dealer was not able to make claim, please email FQA_Inspection_Support@nissan-usa.com for claim processing support. 3. VINs will be noted with PC890 in Service Comm/NSH to allow future headlamp replacement as parts become available. 4. Dealers should use NTB22-039 to correct any vehicles subject to PC890. 5. Once repaired, dealers should submit the claim, using the appropriate claims coding provided for the action taken, and release the vehicle.
REVISION 2 PC861
Service Bulletin/Repair Instructions
Halogen Headlamp Voluntary Service Campaign REVISED September 16, 2022 Please discard earlier versions of this bulletin. The announcement from May 20, 2022 has been revised to include the following changes: Nissan has experienced an unexpected high volume of dealer orders for headlamp assemblies during this campaign. Nissan continues to work expeditiously with the supplier to improve the supply schedule in effort to fulfill DBS orders as quickly as possible. However, headlamp parts supply continues to be very limited for the foreseeable future. Nissan is requesting dealer support to reduce the impact across the network and ensure our customers are taken care of. Nissan is requesting dealers to review their current open parts orders, and is offering a limited opportunity to 1) cancel unnecessary orders and 2) return excess parts in dealer inventory. In the review, please consider future orders, as parts 26060-3TA90 & 26010-3TA9A will not be returnable (J-coded) after October 21, 2022. Nissan reserves the right to make changes to part returns at any time and is subject to change. Parts ordered under PC861 ⢠Dealers can cancel open DBS orders by contacting NNA Campaign Parts at nnacampaignparts@Nissan-Usa.com, and including the required dealer order information. ⢠Dealers can return any excess campaign parts using RFC âIâ-Code by the October 21, 2022 deadline and not affect your obsolescence accrual credit ⢠Parts 26060-3TA9A & 26010-3TA9A will not be returnable (J-coded) after October 21, 2022 Claims processing support ⢠Instruction for claims with inspection prior to May 20, 2022 (PC861); see item 2 under Claims Information section below o Requires work order with open date prior to May 20, 2022 with headlamp diagnosis NG
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REVISION 1 PC861
Service Bulletin/Repair Instructions
Halogen Headlamp Voluntary Service Campaign REVISED May 20, 2022 Please discard earlier versions of this bulletin. The announcement from March 25, 2022 has been revised to include the following: ⢠Revised campaign claims procedure and new campaign ID, due to limited parts availability. See Claims Information section for more detail. ⢠Affected VIN population updated
NTB22-024A
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013-2018 ALTIMA SEDAN; FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-039
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013-2018 ALTIMA SEDAN; FRONT COMBINATION LAMPS (HEADLAMPS) INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2013- 2018 Altima sedan vehicles, to replace both combination lamp (headlamp) assemblies (Halogen only). This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC890 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REV 4 - 2013-18
Service Bulletin/Repair Instructions
Halogen Headlamp Warranty Extension REVISED April 12, 2022 Please discard earlier versions of this bulletin. The announcement from March 25, 2022 has been revised to include the following: ⢠The claims information section has been updated with information regarding vehicles whose warranty extension expired while waiting for parts.
NTB19-076C
Service Bulletin/Repair Instructions
DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
REV 3 - 2013-18
Service Bulletin/Repair Instructions
Halogen Headlamp Warranty Extension REVISED March 25, 2022 Please discard earlier versions of this bulletin. The announcement from February 23, 2022 has been revised to include the following: ⢠The following parts have been placed on parts restriction. Dealers may place a SVC order for the parts listed below via DBS beginning March 25, 2022. Orders will be fulfilled in the order they were received. Existing CSC and VOR backorders will be filled, while STK (stock) backorders will be cancelled. ï 26060-3TA9A LAMP ASSY â HEAD (LH)(Headlamp Assembly) ï 26010-3TA9A LAMP ASSY â HEAD (RH)(Headlamp Assembly)
NTB22-024
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013-2018 ALTIMA; FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2013-2018 Altima vehicles, to inspect and, if necessary, replace both combination (headlamp) assemblies (Halogen only). This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC861 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
NTB17-039O
Service Bulletin/Repair Instructions
CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB15-049X
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REV2 - 2013-18 A
Service Bulletin/Repair Instructions
Halogen Headlamp Warranty Extension REVISED February 23, 2022 Please discard earlier versions of this bulletin. The announcement from January 25, 2022 has been revised to include the following: ⢠If a customer requests inspection due to a visibility concern, dealers should determine eligibility using the warranty extension page of Service Comm. If eligible, refer to the repair bulletin to perform the necessary diagnostic inspection. o The Technical Service Bulletin has been updated to include an inspection procedure OP Code to support warranty claims processing.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-127B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-071B
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-002A
Service Bulletin/Repair Instructions
2013-2018 ALTIMA; FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039N
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-076B
Service Bulletin/Repair Instructions
2018 ALTIMA AND 2018-2019 ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-077
Service Bulletin/Repair Instructions
DRIVERS POWER SEAT IS INOPERATIVE IF YOU CONFIRM The customer states that one or more of the driver (LH) seat controls are (or were) inoperative, AND/OR The windows, sunroof, sunshade and power mirrors are (or were) inoperative. NOTE: A no start condition may also be present. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Inspect the power seat switch wiring harness for damage. 2. Repair any damage found. 3. Install the rubber grommet listed in PARTS INFORMATION.
2013-18 Altima H
Service Bulletin/Repair Instructions
Halogen Headlamp Class Action Owner Notification Beginning October 25, 2021, current and former owners and lessees of certain 2013-2018 Altimas will receive a postcard from a Settlement Administrator informing them of the terms of a proposed class action that, subject to final court approval, could extend the warranty on the halogen headlamps. The class action lawsuit alleges that 2013-18 Altima models manufactured with halogen headlamps have a defect that causes the internal reflecting surface to delaminate, resulting in dimming of the low beam headlamps. Nissan denies all allegations of wrongdoing and liability but has agreed to this customer service initiative in order to resolve the dispute. Beginning in December 2018, all genuine Nissan replacement parts were manufactured with a new design. The proposed settlement is still subject to final approval by the court presiding over the class action lawsuit. The court will determine if the settlement will be approved at or shortly after a hearing that is scheduled for December 20, 2021. If approved, the warranty extension will become effective 31 days after the approval is granted. Additional communication will be distributed prior to the warranty extension going into effect. To be clear, unless and until the proposed settlement is approved by the presiding court, there is no warranty extension and you should proceed with halogen headlamp-related claims as outlined below in #3 under what dealers should do. The proposed settlement, and the associated potential warranty extension, include many terms and conditions. Rather than attempting to address questions about the proposed settlement terms from customers, it is strongly recommended that you refer customers to the websites and/or telephone numbers listed below so that they can receive information from appropriate sources and to avoid providing incorrect and/or incomplete information.
NTB18-055E
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Altima Maxima Lo
Service Bulletin/Repair Instructions
Rear Lower Suspension Link Warranty Extension Dealer Notification In October 2019, Nissan launched a Voluntary Service Campaign (P9324) on MY2013 Nissan Altima vehicles registered in high road-salt-usage states (Connecticut, Delaware, Iowa, Illinois, Indiana, Kentucky, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, Washington D.C., West Virginia and Wisconsin). In the interest of customer satisfaction, Nissan is providing a warranty extension to certain MY2013 Nissan Altima vehicles that were not included in P9324 and certain MY2014-2018 Nissan Altima and MY2016-2018 Nissan Maxima vehicles in all states. On some affected vehicles, one of the rear lower suspension links may corrode and separate at the bushing joint area. Customers may notice a knocking or rattling noise from the rear of the vehicle or observe wheel misalignment on the rear wheel(s) if the link separates. Owners of eligible vehicles will receive a notification indicating their eligibility for the following: â¢Warranty extension for the rear lower suspension links of 84 months and unlimited miles to their current 36 month/36,000 mile New Vehicle Limited Warranty for a total of 120 months warranty coverage (without regard to mileage). â¢This warranty extension will allow for a one-time replacement of the rear lower suspension links with new parts and a four-wheel alignment if parts are cracked or broken. Voluntary Service Campaign (P9324) on MY2013 Nissan Altima vehicles registered in high road-salt-usage states will continue. What Dealers Should Do: 1.Verify if vehicles are eligible for this Warranty Extension using the warranty extension page of Service Comm. 2.Dealers should remedy any eligible vehicles subject to this warranty extension to ensure customer satisfaction using Technical Field Bulletin NTB21-045.
NTB21-045
Service Bulletin/Repair Instructions
2013-2018 ALTIMA AND 2016-2018 MAXIMA; REAR SUSPENSION LOWER LINK IF YOU CONFIRM The customer experiences a knocking or rattling noise from the rear of the vehicle, Or The rear wheel and tire assemblies have a large amount of positive camber. ACTION Replace both rear lower links.
NTB16-018D
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB15-049W
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-008A
Service Bulletin/Repair Instructions
ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-009K
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118A
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077C
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028C
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-023A
Service Bulletin/Repair Instructions
NISSAN; MICROPHONE DOES NOT WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-013f
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin is no longer active. Please discard previous versions of NTB15-013. Refer to the ESM for the fluid cooler cleaning procedure.
NTB17-039m
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071a
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-008b
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049v
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039l
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB20-076
Service Bulletin/Repair Instructions
2021 ALTIMA WITH PR25DD ENGINE; NO ENGINE COVER SERVICE INFORMATION The APPLIED VEHICLE is not equipped with an engine cover. DO NOT file a warranty claim for a missing engine cover.
NTB19-076a
Service Bulletin/Repair Instructions
2018 ALTIMA AND 2018-2019 ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED IF YOU CONFIRM One or more of the following DTCs are stored: P0776, P2813, P0841, P17F0, P17F1, P1715 HINT: ï· If DTCs other than those listed above are stored, this bulletin does not apply. ï· If the customer states the engine stalled while going from 'P' or 'N' range to 'R' or 'D' range, this bulletin does not apply. ï· If DTC P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. ï· If DTC P1715 is the only code stored, this bulletin does not apply. ACTION See Repair Flow Chart on page 2 to confirm if this bulletin applies. HINT: The following pages must be printed and attached to the RO: 1. Clutch Total End Play Calculation (Step 97 on page 63) 2. Consult screen shot showing the TCM part numbers (Step 152 on page 89) 3. Current Calibration Data (Step 155 on page 90) 4. New Calibration Data (Step 171 on page 91) 5. Parts Kit Reference Table (Page 99)
NTB17-039k
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of these DTCs is stored: ï· P17F0 (CVT_JUDDER (T/M INSPECTION)) ï· P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: ï If a transmission judder (as described above) is not reported, this bulletin does not apply. ï If either P17F0 or P17F1 are not stored, this bulletin does not apply. ï If any DTCs are stored other than P17F0 or P17F1, this bulletin does not apply. ï NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTION ï· Refer to the Repair Flow Chart on page 2 for CVT repair. CAUTION: Always handle the CVT and component assemblies carefully and with the appropriate lifting tools.
NTB15-049u
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-025a
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2018 ALTIMA AND ROGUE; CYLINDER HEAD This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard previous versions of this bulletin.
NTB20-027a
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2018 ALTIMA AND ROGUE; EXHAUST MANIFOLD AND THREE WAY CATALYST ASSEMBLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard previous versions of this bulletin.
PC716_PC717 2018
Service Bulletin/Repair Instructions
QR25 Cylinder Head Voluntary Emission Recall Campaign ***** Campaign Summary ***** Nissan is conducting a Voluntary Emission Recall Campaign on approximately 2,209 specific MY2018 Nissan Rogue (T32) and 5,557 specific MY2018 Altima (L33) 2.5L vehicles identified in Service Comm to inspect the engine identification markings and, if they are from the subject manufacturing lot, the suspect cylinders and spark plugs will be inspected. If necessary, dealers may replace the engine, exhaust manifold catalyst, air fuel (A/F) ratio sensor, and oxygen sensor. A machining issue in the engine may exist, which could allow oil to escape past the valve guides and enter the combustion chamber. If an affected engine is not repaired, the performance of the manifold catalyst could degrade over time and cause exhaust gas emissions to exceed standards at high mileage. This incident has no effect on safety or fuel consumption but may decrease engine performance in rare cases. If Nissan has previously replaced the engine in the vehicle due to this condition, the exhaust manifold catalyst, air fuel (A/F) ratio sensor, and oxygen sensor will be replaced. ***** What Dealers Should Do**** 1. Verify campaign applicability using Service Comm or DBS National Service History â Open Campaign I.D. ï· PC716 - Inspect Engine Identification Markings ï· PC717 - Manifold Catalyst Replacement 2. Dealers should use the appropriate campaign bulletin to remedy any vehicles subject to these campaigns: ï· PC716 â NTB20-025 ï· PC717 â NTB20-027 3. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
NTB20-025
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2018 ALTIMA AND ROGUE; CYLINDER HEAD INTRODUCTION Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2018 Altima and Rogue vehicles. The cylinder head will be inspected, and the long engine assembly replaced if needed. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC716 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealerâs responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealerâs inventory. Federal law requires that new vehicles in dealer inventory which are the subject of an emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
NTB20-027
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2018 ALTIMA AND ROGUE; EXHAUST MANIFOLD AND THREE WAY CATALYST ASSEMBLY INTRODUCTION Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2018 Altima and Rogue vehicles. The exhaust manifold and three way catalyst assembly and two exhaust sensors will be replaced. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC717 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealerâs responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealerâs inventory. Federal law requires that new vehicles in dealer inventory which are the subject of an emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
NTB17-039j
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-055d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039i
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB15-049t
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055g
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-045b
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008, VEHICLES REGISTERED OUTSIDE OF CALIFORNIA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-115a
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9345, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
P9328_P9343_P934
Service Bulletin/Repair Instructions
Engine Control Module (ECM) Reprogram California Voluntary Emissions Service Campaign ***** Campaign Summary***** Nissan is conducting a Voluntary Emissions Service Campaign on approximately 104,221 specific Nissan vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or âSmog Checkâ test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. ï· P9328 â Affected Model Year 2015 ï· P9343 â Affected Model Year 2016 ï· P9345 â Affected Model Year 2017 ï· P9347 â Affected Model Year 2018 ï· P9349 â Affected Model Year 2019 2. Dealers should remedy any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction.
NTB19-115
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9435, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
NTB15-013e
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-076
Service Bulletin/Repair Instructions
2018 ALTIMA AND ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED IF YOU CONFIRM One or more of the following DTCs are stored: P0776, P2813, P0841, P17F0, P17F1, P1715 HINT: ï· - If DTCs other than those listed above are stored, this bulletin does not apply. ï· - If the customer states the engine stalled while going from 'P' or 'N' range to 'R' or 'D' range, this bulletin does not apply. ï· - If DTC P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. ï· - If DTC P1715 is the only code stored, this bulletin does not apply. ACTION See Repair Flow Chart on page 2 to confirm if this bulletin applies. HINT: The following pages must be printed and attached to the RO: 1. Clutch Total End Play Calculation (Step 97 on page 63) 2. Consult screen shot showing the TCM part numbers (Step 152 on page 89) 3. Current Calibration Data (Step 155 on page 90) 4. New Calibration Data (Step 171 on page 91) 5. Parts Kit Reference Table (Page 99)
NTB19-045a
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-072
Service Bulletin/Repair Instructions
TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch of the APPLIED VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. ï· Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NTB14-012e
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049s
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-045
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has a stored DTC shown in Table A on the next page, AND The ECM part number is shown in Table B, starting on page 3. ACTION First, perform the appropriate diagnostic procedure for the stored code to repair the vehicle according to the Electronic Service Manual (ESM), AND Reprogram the ECM after performing the diagnosis and repair.
NTB18-019a
Service Bulletin/Repair Instructions
2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-060c
Service Bulletin/Repair Instructions
ABNORMAL NOISE FROM FRONT ENGINE MOUNT SERVICE INFORMATION A two-piece design front engine mount is currently being used for the Applied Vehicles listed. A single thunk noise may be heard during the first few accelerations of the day from this type of mount, and is considered normal operation. The mount has also been designed with built-in free play that is normal. Under normal driving conditions: - A thunk noise may be heard during the first few accelerations of the day, And - Does not occur again, or at any other time. DO NOT REPLACE THE MOUNT: - If it has free play or a ?single event? thunk sound during the first few accelerations of the day. This is considered a normal characteristic of this type of engine mount. - Allowable free play (vertical movement) is 5 mm. - If a shift shock condition is present when shifting from Park into gear or between any combination of gears. This condition is due to transmission line pressure and not movement of the mount. - If a whistle type noise is heard. This is caused by a disconnected vacuum line. NOTE: Refer to the appropriate section of the Electronic Service Manual (ESM) related to transaxles for further diagnostic information on shift shock. Warranty claims for front engine mount replacement due to a whistle noise or a mount that has 5 mm or less free play will be denied.
NTB18-055c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-008a
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-030
Service Bulletin/Repair Instructions
2016-2018 NISSAN; MIL ON WITH DTC P0171, P0174, P2097, AND/OR P2099 This bulletin applies to Altima vehicles equipped with VQ35 engine only. IF YOU CONFIRM The MIL is ON with one or more of the following Air/Fuel (A/F) Sensor DTCs stored: - P0171 (Fuel Injection System Function) - P0174 (Fuel Injection System Function) - P2097 (A/F SENSOR 1) - P2099 (A/F SENSOR 1) ACTION 1. Perform the appropriate diagnostic procedure outlined in the Electronic Service Manual (ESM). 2. Refer to Table A on page 2 and page 3 to confirm if Electronic Control Module (ECM) reprogramming is needed.
NTB12-100b
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103g
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-022
Service Bulletin/Repair Instructions
NISSAN; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.
NTB19-021
Service Bulletin/Repair Instructions
NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
NTB18-032a
Service Bulletin/Repair Instructions
ALTIMA AND MAXIMA; NOISE FROM TRUNK AREA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028b
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-009j
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSINGOR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB15-049r
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-008
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D SERVICE INFORMATION When key registration is unsuccessful after BCM replacement, P161D (Immobilizer) will set when the ignition is turned on. Possible causes - Improper key registration - Defective BCM (Vehicles with Intelligent Key only) - EPS control unit (Vehicles with mechanical key only) - Intelligent Key unit (Vehicles with mechanical key only) Trouble Diagnosis NOTE: If DTC B2196-52 is stored with P161D, perform the diagnosis procedure for DTC B2196-52 first. - Before replacing the BCM, confirm that the keys were programmed correctly by ensuring the vehicle will start and that the lock/unlock buttons function normally. - If any keys do not function normally, re-register all of the keys. - After re-registering all of the keys, reconfirm each key's function. - If OK, erase the code to complete the repair. - If NG, diagnose the Key, BCM and/or EPS control unit per the ESM.
REVISION 1-PC657
Service Bulletin/Repair Instructions
Front Passenger Seatback Voluntary Service Campaign REVISED November 16, 2018 Please discard earlier versions of this bulletin. The announcement from October 5, 2018 has been revised to include the following: The following parts are no longer on restriction and may be ordered via normal ordering process beginning November 16, 2018. - 87600-9HT0B Seatback (Beige/C) - 87600-9HT2A Seatback (Charcoal/G) - 87600-9HU1C Seatback (Sport Interior/Z) Parts currently on order in DBS will be fulfilled
NTB18-080
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
NTB12-103f
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055a
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR SERVICE INFORMATION Applied Vehicles listed above are no longer equipped with a door unlock sensor and/or Body Control Module (BCM) software to provide support for the door unlock sensor. Normal Functionality For Vehicles Built Without Door Unlock Sensor And/Or BCM Software To Support Door Unlock Sensor For Applied Vehicles built after the Applied Dates listed on page 1, using the mechanical key on the driver door will operate differently than vehicles built before the Applied Dates. For these later models, the BCM will not recognize operation of the mechanical key. If a mechanical key is used to lock the driver door: - The security system will not set. If the vehicle is broken into, the alarm will not sound. - Only the driver door will be locked. Other doors will not lock using the mechanical key. If a mechanical key is used to unlock the driver door: - Only the driver door will be unlocked. Other doors will not be unlocked. - If the security system is set, when the door is opened the alarm will sound. NOTE: Using the Unlock button on the Intelligent Key, pushing the request switch on the driver or passenger door with the Intelligent Key in range, or using the Intelligent Key to start the vehicle will silence the alarm. The mechanical key will not operate the power windows.
NTB15-077b
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
PC657 2018 Altim
Service Bulletin/Repair Instructions
Front Passenger Seatback Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a Voluntary Service Campaign to replace the seat back assembly on specific 2018 Nissan Altima (L33) vehicles. Due to a manufacturing issue, which has since been corrected, an outboard headrest tube was not fully welded to the right front seat back frame during headrest assembly. As a result, customers may experience a rattle (noise) concern. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or National Service History ? Open Campaign I.D. PC657. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory prior to sale to ensure customer satisfaction. 3. Dealers should use NTB18-067 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
NTB18-067
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2018 ALTIMA; FRONT PASSENGER SEATBACK INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2018 Altima vehicles to replace the front passenger seatback assembly. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC657 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
NTB15-049q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
NTB13-077d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB15-049p
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.
NTB18-055
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each dealer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.
NTB18-017b
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.
NTB18-006
Service Bulletin/Repair Instructions
2016-2018 ALTIMA WITH QR25DE/4-CYL ENGINE; MOAN NOISE AFTER A/C COMPRESSOR ENGAGES This bulletin applies only to vehicles equipped with a 4-cylinder engine. IF YOU CONFIRM A moan type noise is heard just after the A/C is turned ON (compressor engages) and lasts for about 10 seconds and/or While the A/C is operating and the compressor clutch cycles from OFF to ON, the moan noise is heard for about 10 seconds. ACTION Replace the low pressure A/C flex hose with the one listed in PARTS INFORMATION. Do NOT replace the compressor for this incident, if it should occur. This bulletin does not apply for compressor clutch locked, squeal noises, or any other A/C malfunctions.
PC622
Service Bulletin/Repair Instructions
State Specific Bumper Performance Label Dealer Inventory *****Detailed Information***** Nissan is conducting a quality action specific to dealers located in California and Hawaii only to apply a supplemental bumper performance label. Due to an issue that has since been corrected, the bumper performance language may be missing from the Monroney label. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. In the interest of customer satisfaction, Nissan requests dealers to apply the supplemental bumper performance label on the affected vehicles prior to retail sale. *****What Dealers Should Do***** 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History ? Open Campaign I.D. PC622 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to remedy vehicles affected by this quality action. 3. The service department should submit the applicable warranty claim for the action(s) performed so it can be closed on Service Comm and release the vehicle. 4. Dealers will receive five (5) extra labels, but if additional labels are needed, please send your request for the number of labels needed to CampaignAnnouncements@nissan-usa.com along with your dealer name, address and contact name and phone number. - Labels will be mailed beginning May 25, 2018 and should arrive no later than June 1, 2018
NTB15-009i
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The tables on pages 6 - 9 have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB14-053b
Service Bulletin/Repair Instructions
2014-2018 ALTIMA; HYDRAULIC ELECTRIC POWER STEERING SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB18-032
Service Bulletin/Repair Instructions
ALTIMA AND MAXIMA; NOISE FROM TRUNK AREA IF YOU CONFIRM A ticking, tapping, or popping type noise is coming from the area of the right rear parcel shelf or right rear passenger seatback area while driving. ACTION 1. Widen the gap between two pieces of body paneling in the right side trunk area. 2. Fill the gap with expanding foam. - Refer to Service Procedure in this bulletin for the repair procedure.
NTB16-018c
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-009h
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The tables on page 5 and 6 have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-029
Service Bulletin/Repair Instructions
2013-2018 ALTIMA; AFTERMARKET HEADLIGHTS SERVICE INFORMATION If a headlight housing assembly on an applied vehicle needs to be replaced for any reason, note the following: - Only Original Equipment (O.E.) components are warrantable though Nissan. - Aftermarket components are not warrantable through Nissan. - Confirm that it is a genuine Nissan part before submitting a Warranty Claim. - Genuine Nissan headlight housings, on an applied vehicle, will have "Nissan" and "NAL" markings on the housing. - See examples of an O.E. headlight housing assembly (Figure 1 on page 2) and aftermarket headlight housing assembly (Figure 2 on page 3). NOTE: The Nissan New Vehicle Limited Warranty does not cover aftermarket components. Refer to the Nissan Assurance Products Resource Manual (APRM) for guidelines on warranty coverage. The vehicle Owner's Manual contains the complete details regarding the limited warranty.
NTB13-107b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
NTB18-017a
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.
NTB11-044c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-023
Service Bulletin/Repair Instructions
NISSAN; MICROPHONE DOES NOT WORK This bulletin applies only to vehicles equipped with Telematics. IF YOU CONFIRM The microphone of an applied vehicle does not work. - The person receiving your call through Bluetooth® cannot hear you. And Voice Recognition does not respond to any commands. NOTE: DTCs U1A01 and/or U1A02 may be found stored. ACTION 1. Confirm TCU reprogramming will resolve the issue. - Refer to ?Issue Confirmation? on page 2. 2. If confirmed, reprogram the TCU.
NTB15-009g
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The Applied Vehicles section has been revised, and changes have been made to the table beginning on page 5. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-019
Service Bulletin/Repair Instructions
2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS SERVICE INFORMATION A new Engine Support Tool and Engine Support Bracket are now available to allow the CVT to be removed from the Applied Vehicles without having to remove the engine. The procedures in this bulletin are different than those that are currently in the Electronic Service Manual (ESM), which will be updated with this information at a later date. Please refer to the vehicle specific service procedure to use these new tools: Altima Page 2 Rogue AWD Page 11 Rogue FWD Page 24
NTB18-017
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.
NTB15-049o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.
NTB18-008
Service Bulletin/Repair Instructions
ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin applies only to vehicles equipped with Automatic Emergency Braking (AEB) or Forward Emergency Braking (FEB). SERVICE INFORMATION If the following ICC/ADAS codes are stored, make sure to follow the diagnostic procedures in the Electronic Service Manual (ESM) before replacing any parts. C1A03 ? VEHICLE SPEED SENSOR -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1A04 ? ABS/TCS/VDC SYSTEM -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1B01 CAM AIMING INCMP -The diagnostic procedure in the ESM includes check and, if needed, repair for LANE CAMERA DTCs before replacing ADAS components. -LANE CAMERA DTC may require adjustment of the lane camera. -If repairs/adjustments are performed for the Lane Camera; when compete, perform DTC Confirmation Procedure again before doing any additional repairs.
NTB15-049n
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a TCU (Telematics Communication Unit). This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.
NTB17-123
Service Bulletin/Repair Instructions
2018 ALTIMA AND SENTRA; DO NOT ERASE DTC P0315 This bulletin applies to vehicles equipped with a 4-cyl (non-turbo) engine only. SERVICE INFORMATION If DTC P0315 is stored on an Applied Vehicle, do not erase it. If DTC P0315 is stored, the description on the CONSULT-III plus screen will be listed as: (TBD) Crankshaft Position System Variation Not Learned. If you find DTC P0315 stored, please note the following: - Do not erase the DTC. - It will not turn ON the MIL. - No diagnosis or repair is necessary. - It will clear itself after a few trips with normal operation of the vehicle. NOTE: If DTC P0315 is erased with C-III plus, the ECM will restart the learning pattern: - The DTC may be stored again before the learning/driving pattern is complete. - The MIL will not come ON. - The DTC will clear itself after a few trips with normal operation of the vehicle.
NTB17-118
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin applies to vehicles equipped with Intelligent Key only. SERVICE INFORMATION When replacing or adding an Intelligent Key, it is very important to make sure the correct Intelligent Key is selected from the parts department. - A running change was made that will help identify the correct Intelligent Key. - Beginning in late 2017 and early 2018 the last five digits of the Intelligent Key part number is marked on the Intelligent Key under the mechanical key. - See page 2 for location images of this part number addition. NOTE: - A correct Intelligent Key may or may not have the last five digits of the part number as shown on page 2. - The above running change was applied as a ?help? to identify the correct Intelligent Key for a given vehicle, but the actual part number listed in the parts catalog did not change. - Make sure to use the electronic parts catalog (FAST) or equivalent to confirm the correct Intelligent Key for a given vehicle.
NTB15-049m
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with a wireless communication device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.
NTB15-049L
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.
NTB11-044b
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-049k
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. The Applied Vehicles section has been revised and TCU Configuration section has been added. No other changes have been made. Please discard previous versions of this bulletin.