Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB15-049CC
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION HINT: This bulletin applies to vehicles equipped with a 4G network compatible TCU. TCUs compatible with 3G network only are no longer supported. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the NissanConnect® Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. · A table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. · A CHECK-OFF SHEET has been provided on page 20 to print and check off steps as they are performed. Staple the completed CHECK-OFF SHEET to the repair order.
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB20-066C
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. For all other models/model years, consult the Electronic Service Manual (ESM).
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB12-103I
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-038C
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-073B
Service Bulletin/Repair Instructions
REAR AUTOMATIC BRAKING WARNING LIGHT ILLUMINATED AND/OR DTC C1B56-04 AND/OR C1B56-97 STORED IN THE ADAS CONTROL UNIT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB20-046G
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB15-049AA
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003F
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-094B
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC989 2019-2020
Service Bulletin/Repair Instructions
Active Grille Shutter Emission Warranty Extension Dealer Notification *****Dealer Announcement***** Nissan is committed to providing the highest levels of product quality and customer satisfaction. Therefore, Nissan is extending the emission warranty coverage on the model year 2019-2020 Altima Active Grille Shutter to 15 Years or 150,000 miles, whichever occurs first. All other warranty terms, limitations, and conditions remain unchanged. On affected vehicles, over time, the shaft connecting the grille shutter motor and shutter louvers may become twisted and/or cracked resulting in the shutter remaining in the closed position and illumination of the malfunction indicator light (MIL). This issue will have no effect on vehicle safety or drivability, but the vehicle may experience reduced fuel efficiency. During the limited emission warranty extension period, owners are eligible for free replacement of the Active Grille Shutter if a MIL-On condition occurs with DTC P059F and/or P159F that requires replacement of the grille shutter assembly. Owners of eligible vehicles will receive notification of this limited emission warranty extension during December 2023. ***** What Dealers Should Do ***** 1. Verify if vehicles are eligible for this Warranty Extension using the warranty extension page of Service Comm. 2. If a customer contacts the dealer with an Active Grille Shutter concern in an owned or leased vehicle, dealers should use the ESM to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval when the repair cost exceeds a Dealerâs Claims Administration/Authorization Limits (DCAL). 3. The service department should submit the applicable warranty claim for the action performed.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051B
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-038B
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB12-103H
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-038
Service Bulletin/Repair Instructions
WARNING LIGHT ON WITH DTC C111F STORED AS CRNT IN THE ABS IF YOU CONFIRM DTC C111F (G-SENSOR) is stored as âCRNTâ in the ABS Actuator and Electric Unit (Control Unit). IMPORTANT: Do not replace the ABS control unit unless instructed to do so. ACTION Refer to the SERVICE PROCEDURE on page 2 to calibrate the Decel G-Sensor.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-071C
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-030
Service Bulletin/Repair Instructions
CVT SHIFT SELECTOR LEVER KNOB REMOVAL AND INSTALLATION SERVICE INFORMATION If the CVT Shift Selector Lever Knob needs to be removed or installed for any reason, refer to the SERVICE PROCEDURE in this bulletin, beginning on page 2.
NTB20-046F
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013B
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-010C
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051A
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-038A
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-073A
Service Bulletin/Repair Instructions
REAR AUTOMATIC BRAKING WARNING LIGHT ILLUMINATED AND/OR DTC C1B56-04 AND/OR C1B56-97 STORED IN THE ADAS CONTROL UNIT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049Z
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB15-049Y
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-029I
Service Bulletin/Repair Instructions
ABNORMAL NOISE, VIBRATION AND/OR BINDING FEELING FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-097
Service Bulletin/Repair Instructions
DTC P0404 STORED IN THE ECM AT TEMPERATURES BELOW 32°F IF YOU CONFIRM DTC P0404 (EGR A CONTROL) is stored in the ECM at temperatures below 32°F. ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013A
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-073
Service Bulletin/Repair Instructions
REAR AUTOMATIC BRAKING WARNING LIGHT ILLUMINATED AND/OR DTC C1B56-04 OR C1B56-97 STORED IN THE ICC/ADAS2 CONTROL MODULE SERVICE INFORMATION If the customer states the rear automatic braking (RAB) warning light was illuminated and âMalfunction See Ownerâs Manualâ appears in the message center (Figure 1), AND / OR DTC C1B56-04 and/or C1B56-97 are stored in the ICC/ADAS2 Control Module. Refer to the information on page 2 to determine next steps.
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003E
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-094A
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051
Service Bulletin/Repair Instructions
HORN INOPERATIVE IF YOU CONFIRM The horn on an APPLIED VEHICLE is inoperative. ACTION Inspect the horn pad for a pinched ground wire. If a pinched ground wire is found, replace the high and low horns.
NTB10-029H
Service Bulletin/Repair Instructions
NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-038
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED IF YOU CONFIRM The customer states an RAB warning light in the instrument panelâs information display is ON (Figure 1), AND/OR DTC B2724-23 (SONAR CONTROL UNIT - SONAR ECU INTERNAL FAILURE [UNDER VOLTAGE]) is stored. NOTE: A RAB warning light may appear in the vehicle information display. ACTION Reprogram and configure the Sonar Control Unit with the SERVICE PROCEDURE in this bulletin, if applicable.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB10-029G
Service Bulletin/Repair Instructions
NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-020
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR BRAKE SWITCH ADJUSTMENT FOR DTC C1142 AND/OR C1116 STORED SERVICE INFORMATION DTC C1142 (PRESS SEN CIRCUIT) and/or C1116 (STOP LAMP SW) may be stored if the Stop Lamp Switch and/or the Brake Pedal Position Switch are out of adjustment. Before replacing any components for DTCs C1142 (PRESS SEN CIRCUIT) and/or C1116 (STOP LAMP SW), stored as past or current, confirm that the Stop Lamp Switch and the Brake Pedal Position Switch are properly adjusted. If either the Stop Lamp Switch and/or the Brake Pedal Position Switch are found to be out of adjustment, adjust them as per the ESM, and then clear the DTCs and perform DTC confirmation. ï· Refer to the ESM: BRAKES > BRAKE SYSTEM > PERIODIC MAINTENANCE > BRAKE PEDAL > Adjustment
NTB15-049X
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003D
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071B
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003C
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-046E
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-083A
Service Bulletin/Repair Instructions
DTC P17F0, P17F1, P0776, P2813 AND/OR P0841 STORED IN THE TCM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB21-094
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL SERVICE INFORMATION When removing the front passenger (RH) side drive shaft on an applied vehicle for any reason, transfer assembly drive shaft oil seal and dust cover seal replacement is required. Refer to the SERVICE PROCEDURE in this bulletin.
NTB21-083
Service Bulletin/Repair Instructions
DTC P17F0, P17F1, P0776, P2813 AND/OR P0841 STORED IN THE TCM IF YOU CONFIRM One or more of the following DTCs are stored: P0776, P2813, P0841, P17F0, P17F1 HINT: ï· If DTCs other than those listed above are stored, this bulletin does not apply. ï· If the customer states the engine stalled while going from 'P' or N' range to 'R' or 'D' range, this bulletin does not apply. ï· If DTC P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. ACTION See Repair Flow Chart on page 2 to confirm if this bulletin applies. HINT: The following pages must be printed and attached to the Repair Order (RO): 1. Clutch Total End Play Calculation (step 93 on page 60) 2. Current Calibration Data (step 138 on page 80) 3. New Calibration Data (step 154 on page 81)
NTB21-034A
Service Bulletin/Repair Instructions
AC INOPERATIVE WITH DTC B20C8-14 STORED IN THE IPDM E/R This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-118B
Service Bulletin/Repair Instructions
ALTIMA, KICKS AND VERSA SEDAN; DTC B26FE IN BCM AND KEY SYSTEM ERROR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB17-003B
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-034
Service Bulletin/Repair Instructions
2019-2021 ALTIMA AND 2021 ROGUE; AC INOPERATIVE WITH DTC B20C8-14 STORED IF YOU CONFIRM The AC compressor is not engaging when the AC is in the ON position as indicated by the yellow illumination on the AC button, And DTC B20C8-14 ECV (ELECTRICAL CONTROL VALVE) is stored in the IPDM. SERVICE PROCEDURE 1. Clear the DTC, and follow the DTC CONFIRMATION PROCEDURE in the ESM. ï· If DTC B20C8-14 is past, AC compressor operation is inhibited until the DTC is cleared. ï· If DTC B20C8-14 returns after being cleared (either Current or Past status), follow the ESM diagnosis procedure. ï For models with Automatic Air Conditioning, go to section: VENTILATION, HEATER & AIR CONDITIONER > HEATER & AIR CONDITIONING CONTROL SYSTEM > AUTOMATIC AIR CONDITIONING > DTC/CIRCUIT DIAGNOSIS > B20C8-14 ECV (ELECTRICAL CONTROL VALVE). ï For models with Manual Air Conditioning, go to section: VENTILATION, HEATER & AIR CONDITIONER > HEATER & AIR CONDITIONING CONTROL SYSTEM > MANUAL AIR CONDITIONING > DTC/CIRCUIT DIAGNOSIS > B20C8-14 ECV (ELECTRICAL CONTROL VALVE).
NTB21-027
Service Bulletin/Repair Instructions
MIL ON WITH DTC P062F AND/OR P0603 STORED IF YOU CONFIRM The MIL is ON and DTC P062F (EEPROM) and/or P0603 (ECM BACK UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicleâs 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.
NTB19-118A
Service Bulletin/Repair Instructions
ALTIMA, KICKS AND VERSA SEDAN; DTC B26FE IN BCM AND KEY SYSTEM ERROR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB15-049W
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077C
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028C
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL SERVICE INFORMATION If an Applied Vehicle needs to have a front axle nut removed, for any reason, the staking of the nut into the axle keyway must first be removed. The essential tool (part number # J-52982, Figure 1) required to remove the nut staking, is called out as a âCape Chiselâ in the Electronic Service Manual (ESM), and must be used to prevent thread damage to the axle (see Figure 2 on page 2). ï· The Cape Chisel arrived at dealers in December of 2020. ï· Damaged threads, due to improper removal of the stake placed in the nut, will not be covered by warranty. For information on using the Cape Chisel, refer to the Electronic Service Manual (ESM): Section TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT > LH/RH.
NTB20-083A
Service Bulletin/Repair Instructions
2019-2020 ALTIMA; DTC P2015 OR P2004 STORED DURING COLD WEATHER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-008b
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-046d
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066b
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-029a
Service Bulletin/Repair Instructions
INTELLIGENT KEY DOES NOT WORK AFTER BATTERY REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080a
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
NTB21-009
Service Bulletin/Repair Instructions
DTC B12A3-72 FOR FUEL PUMP RELAY STUCK OPEN SERVICE INFORMATION DTC B12A3-72 (Fuel Pump Relay Stuck Open) may be stored when the IPDM monitor circuit internally sees 0V to ground at pin #46. This is caused by an internal short to ground in the IPDM or one of the IPDM fuses listed below is open. If B12A3-72 is current or reoccurs after erasing DTCs, inspect the model specific fuse first. If the fuse is not open replace the IPDM. ï· Altima â Fuse # 58 (page 2) ï· Kicks â Fuse # 54 (page 3) ï· Versa â Fuse # 61 (page 4) For additional IPDM diagnostic information refer to the Electronic Service Manual (ESM): Section ELECTRICAL & POWER CONTROL > POWER CONTROL SYSTEM > IPDM E/R. See model specific fuse locations starting on page 2.
NTB15-049v
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-056a
Service Bulletin/Repair Instructions
MIL ON WITH P0101 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-083
Service Bulletin/Repair Instructions
2019-2020 ALTIMA; DTC P2015 OR P2004 STORED DURING COLD WEATHER IF YOU CONFIRM The customer stated that the MIL was on after starting the engine in cold weather, below 0°F. And DTC P2015 (INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR) and/or DTC P2004 (INTAKE MANIFOLD RUNNER CONTROL VALVE) are stored in the ECM. DTC status is either current or past. And No problem is found after performing the DTC diagnosis per the Electronic Service Manual (ESM). ACTION Replace the intake manifold.
NTB20-080
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV control unit before starting the diagnosis. The software update in the following service procedure is to address the items below: ï· Stability improvements and âbugâ fixes. ï· Android Auto skips while playing music. Refer to steps 1 - 4 to confirm that this bulletin applies. HINT: The update-software only needs to be downloaded once and then can then be used on multiple vehicles until other infotainment software is loaded onto the USB drive to overwrite the original data.
NTB19-042a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-076
Service Bulletin/Repair Instructions
2021 ALTIMA WITH PR25DD ENGINE; NO ENGINE COVER SERVICE INFORMATION The APPLIED VEHICLE is not equipped with an engine cover. DO NOT file a warranty claim for a missing engine cover.
NTB20-066a
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-029f
Service Bulletin/Repair Instructions
NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle during the following conditions: ï· When making turns ï· On dry roads ï· At low speeds (under 40 MPH) And ï· The above vibration does not occur if the Electric Controlled Coupling is electrically disconnected. NOTE: In some cases, electrically disconnecting the Electric Controlled Coupling may not eliminate the vibration as described above. In these cases, further confirm the incident by removing the rear propeller shaft and retest. If the vibration does not occur with the rear propeller shaft removed, the incident is confirmed. IMPORTANT: Tire size, brand or tread pattern mismatches can cause similar symptoms. To avoid tire related mismatch vibration, it is recommended that when tires need to be replaced, all tires are replaced at the same time with tires of the proper size, same brand and pattern. See ACTION on page 2.
NTB20-066
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. ï· For all other models/model years, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure. ï· Refer to the ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).
NTB20-064
Service Bulletin/Repair Instructions
ALTIMA WITH PR25DD ENGINE; DTC P0015 STORED IF YOU CONFIRM DTC P0015 (B camshaft position B1) is stored NOTE: The MIL may or may not be ON. And Diagnosis has determined the exhaust valve timing control solenoid valve is the cause. ACTION Replace the exhaust valve timing control solenoid valve. NOTE: The exploded views in the 2019 and 2020 Altima ESM may incorrectly label the exhaust valve timing control solenoid valve and the exhaust valve timing intermediate lock control solenoid valve. The exhaust valve timing control solenoid valve is positioned below the exhaust valve timing intermediate lock control solenoid valve on the front cover.
NTB20-046a
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-046
Service Bulletin/Repair Instructions
2019-2020 ALTIMA; VOLUME KNOB DOES NOT FUNCTION PROPERLY IF YOU CONFIRM The customer states the speaker volume does not change or changes erratically when rotating the volume knob. ACTION 1. Rotate the volume knob rapidly two times, for a total of 60-seconds, to remove contaminate build-up. 2. Update the display control unit software.
NTB19-067c
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049u
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003a
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049t
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-045b
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008, VEHICLES REGISTERED OUTSIDE OF CALIFORNIA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-115a
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9345, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
P9328_P9343_P934
Service Bulletin/Repair Instructions
Engine Control Module (ECM) Reprogram California Voluntary Emissions Service Campaign ***** Campaign Summary***** Nissan is conducting a Voluntary Emissions Service Campaign on approximately 104,221 specific Nissan vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or âSmog Checkâ test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. ï· P9328 â Affected Model Year 2015 ï· P9343 â Affected Model Year 2016 ï· P9345 â Affected Model Year 2017 ï· P9347 â Affected Model Year 2018 ï· P9349 â Affected Model Year 2019 2. Dealers should remedy any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction.
NTB19-115
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9435, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
NTB19-118
Service Bulletin/Repair Instructions
ALTIMA, KICKS AND VERSA SEDAN; MIL ON WITH DTC B26FE IF YOU CONFIRM ï· A âKey System Errorâ message is displayed on the combination meter, And ï· DTC B26FE (IPDM - KEY SYSTEM ERROR) is stored in the BCM. ACTION 1. Disconnect the main power harness connector from the IPDM (E16 for Altima and E42 for Kicks and Versa Sedan). ï· - See Figure 1, Figure 2 and Figure 3 on the next page for IPDM main power harness connector locations. 2. Wait at least 20 seconds. 3. Reconnect the main power harness connector to the IPDM. 4. Confirm that the DTC is now past, and then erase the DTC. If the DTC will not erase, refer to the Electronic Service Manual for additional diagnostic information.
Expiraton Notifi
Service Bulletin/Repair Instructions
VCR Engine Inspection â Expiration Notice UPDATE November 11, 2019 Please discard earlier versions of this bulletin. Nissan announced the following quality action in July 2019. Service Comm will de-active PC707 on any unrepaired VINs on November 15, 2019. Please inspect and, if necessary, remedy any vehicles with an open campaign prior to November 15, 2019.
NTB19-100
Service Bulletin/Repair Instructions
2019-2020 ALTIMA; FOAM OUT OF POSITION AND VISIBLE AT LEADING EDGE OF INSTRUMENT PANEL IF YOU CONFIRM There is foam out of position and visible between the leading edge of the instrument panel and the bottom of the windshield (Figure 1 shows foam out of position as viewed from outside the vehicle on the passenger side). ACTION Remove the foam following the SERVICE PROCEDURE on the next page.
NTB19-067b
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-045a
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-072
Service Bulletin/Repair Instructions
TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch of the APPLIED VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. ï· Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NTB19-067a
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV unit before starting the diagnosis. The software updates in the following Service Procedure are for the items below: ï· Stability improvements and bug fixes ï· System enhancements that will allow future Over-The-Air (OTA) updates. Without these software updates, future OTAs will not be possible. Refer to step 5 on page 5 to confirm that this bulletin applies. HINT: The update software only needs to be downloaded once and can then be used on multiple Applied Vehicles until other infotainment software is loaded onto the USB drive to overwrite the original data.
NTB14-012e
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC707 2019-20 Al
Service Bulletin/Repair Instructions
VCR Engine Inspection *****Dealer Announcement***** Nissan is conducting a quality action on 356 specific MY 2019-20 Altima (L34) vehicles identified in Service Comm, to remove and inspect the lower engine oil pan. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC707 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, sell or trade the specific 2019-2020 Altima vehicles in Dealer Inventory subject to this Quality Action. 3. Use the attached procedure to inspect the vehicle. - If no gold colored debris is found in the lower engine oil pan, reseal the oil pan per the Electronic Service Manual (ESM). - File a claim for the inspection, and release the vehicle for sale - If gold colored debris is found in the lower engine oil pan, provide the requested information in an email to nnafqasupport@nissan-usa.com and HOLD the vehicle. - Do not file a claim Nissan Field Quality will review the E-mail submissions within two (2) business days of receipt and provide further instruction.
NTB15-049s
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-050
Service Bulletin/Repair Instructions
2019 ALTIMA; CLUNK NOISE FROM REAR WHEN DRIVING OVER DIPS AND/OR POTHOLES IF YOU CONFIRM A clunk type noise from the rear of the vehicle ONLY when driving over dips and/or potholes, AND The noise is isolated to the rear shock absorbers. ACTION Replace both rear shock absorbers. See PARTS INFORMATION on the next page.
NTB19-048
Service Bulletin/Repair Instructions
2019 ALTIMA; MIL ON WITH DTC P0087 This bulletin applies only to vehicles equipped with the 2.5L engine. IF YOU CONFIRM The Malfunction Indicator Light (MIL) is ON with Diagnostic Trouble Code (DTC) P0087 (FRP CONTROL SYSTEM) stored in the Engine Control Module (ECM), AND The fuel level indicates ¼ or less. ACTION Reprogram the ECM, if applicable.
NTB19-045
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has a stored DTC shown in Table A on the next page, AND The ECM part number is shown in Table B, starting on page 3. ACTION First, perform the appropriate diagnostic procedure for the stored code to repair the vehicle according to the Electronic Service Manual (ESM), AND Reprogram the ECM after performing the diagnosis and repair.
NTB18-055c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
NTB19-041
Service Bulletin/Repair Instructions
2019 ALTIMA; CREAK OR POP NOISE WHEN TURNING AND ACCELERATING OR DECELERATING This bulletin applies to vehicles equipped with a 2.5L (PR25DD) engine ONLY. IF YOU CONFIRM A creak or pop noise is heard from the front of the vehicle when turning right while accelerating or decelerating. ACTION Replace the engine mounting insulator (LH) with the one listed in the PARTS INFORMATION. - For the procedure to replace the engine mounting insulator (LH) refer to the Electronic Service Manual (ESM): section REPAIR > ENGINE > ENGINE MECHANICAL > REMOVAL AND INSTALLATION > ENGINE MOUNTING INSULATOR (LH)
NTB19-008a
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-029
Service Bulletin/Repair Instructions
INTELLIGENT KEY DOES NOT WORK AFTER BATTERY REPLACEMENT SERVICE INFORMATION If the Intelligent Key of an APPLIED VEHICLE does not work after replacing the battery, inspect the positive (+) terminals. If the battery side of the Intelligent Key is held by pinching down on the terminals while removing the battery, it is possible to bend the terminals down far enough that they will not touch the contacts on the other half of the Intelligent Key. If the terminals are found to be bent down, pry them back up so that they will come in contact with the other half of the Intelligent Key?s contacts. - Refer to the photos on the following pages.
PC692 - 2019 Alt
Service Bulletin/Repair Instructions
Fuel Pump Dealer Inventory This bulletin applies only to vehicles equipped with Front Wheel Drive (FWD). *****Detailed Information***** Nissan is conducting a quality action to inspect and, if necessary, tighten the fuel pump lock ring on one hundred eleven (111) specific 2019 Altima (L34) FWD only vehicles identified in Service Comm. In rare occurrences, the lock ring may be completely disengaged which may require the fuel pump module and seal to be replaced. Due to a supplier issue that has since been corrected, it is possible that the fuel pump module?s lock ring is not fully engaged. If partially locked, it is possible for the fuel pump module?s lock ring to rotate to an unlocked position due to vibration during normal driving conditions. This condition may result in MIL illumination, fuel smell, and/or a rattle noise associated with the fuel pump module plastic flange. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History ? Open Campaign I.D. PC692 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability.
NTB12-100b
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103g
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC689 2019 Altim
Service Bulletin/Repair Instructions
Front Exhaust Tube Voluntary Emission Recall Campaign ***** Campaign Summary ***** Nissan is conducting a Voluntary Emissions Recall Campaign on approximately 5 specific MY2019 Altima (L34) vehicles identified in Service Comm. Due to a manufacturing issue that has since been corrected, certain vehicles may have an incorrect front exhaust tube installed. Dealers will inspect the etched number in the center of the rear front exhaust tube and, if found to be out of specification, replace the front exhaust tube with the correct specification part. ***** What Dealers Should Do**** 1. Verify if campaign applicability using Service Comm or National Service History ? Open Campaign I.D. PC689. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460a for additional information 2. Dealers should use NTB19-024 to identify and, if necessary, correct any vehicles subject to this campaign. 3. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
NTB19-024
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2019 ALTIMA; FRONT EXHAUST TUBE INTRODUCTION Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2019 Altima vehicles. The front exhaust tube will be inspected and, if necessary, replaced. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC689 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer?s responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer?s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of an emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties and/or fines. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
NTB19-021
Service Bulletin/Repair Instructions
NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
PC681 2019 Altim
Service Bulletin/Repair Instructions
Fuel Tank Dealer Inventory *****Dealer Announcement***** Nissan is conducting a quality action to inspect the fuel tank on 80 specific 2019 Altima AWD vehicles identified in Service Comm. Due to a manufacturing issue that has since been corrected, the fuel readings may not be accurate due to the presence of a plastic slug inside the fuel tank. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to complete this inspection and, if necessary, remedy any affected inventory prior to sale to ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC681 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers should use the attached procedure to identify the presence of a plastic slug in the fuel tank for any vehicle subject to this quality action. - Nissan has developed an automatic parts shipment to provide affected dealers with replacement fuel sensing unit packing for affected vehicles in dealer inventory. Parts should begin to arrive at dealers on February 13, 2019 - If no plastic slug is present, install new fuel sensing unit packing and reinstall the fuel sensing unit assembly. Once reinstalled, the vehicle may be immediately released for sale. - If a plastic slug is present, remove the plastic slug, install new fuel sensing unit packing, and reinstall the fuel sensing unit assembly.
NTB16-028b
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB15-049r
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-008
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D SERVICE INFORMATION When key registration is unsuccessful after BCM replacement, P161D (Immobilizer) will set when the ignition is turned on. Possible causes - Improper key registration - Defective BCM (Vehicles with Intelligent Key only) - EPS control unit (Vehicles with mechanical key only) - Intelligent Key unit (Vehicles with mechanical key only) Trouble Diagnosis NOTE: If DTC B2196-52 is stored with P161D, perform the diagnosis procedure for DTC B2196-52 first. - Before replacing the BCM, confirm that the keys were programmed correctly by ensuring the vehicle will start and that the lock/unlock buttons function normally. - If any keys do not function normally, re-register all of the keys. - After re-registering all of the keys, reconfirm each key's function. - If OK, erase the code to complete the repair. - If NG, diagnose the Key, BCM and/or EPS control unit per the ESM.
NTB18-082
Service Bulletin/Repair Instructions
VOLUNTARY RECALL CAMPAIGN 2019 ALTIMA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary recall campaign on certain specific model year 2019 Altima vehicles. The Engine Control Module (ECM) will be inspected, and if necessary, reprogrammed. This action will resolve a potential false Malfunction Indicator Lamp (MIL) issue. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number R1813 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer's responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer's inventory.
PC669 2019 Altim
Service Bulletin/Repair Instructions
Fuel Feeder Tube Clip Dealer Inventory *****Dealer Announcement***** Nissan is issuing a quality hold to require dealers to inspect the Fuel Feeder Tube Clip position and confirm it is in the lock position on ~15,800 specific 2019 Altima vehicles identified in Service Comm. The clips may not be fully locked into place. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Dealers must complete this inspection and if necessary, repair, prior to sale. The inspection and if necessary, repair; will take less than 15 minutes per vehicle to complete and no parts are required. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC669 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers should inspect the Fuel Feeder Tube Clip position to confirm it is in the locked position. 3. Use the attached procedure to inspect any vehicles affected by this quality action: - If inspection result is ?OK?, dealers may submit a warranty claim using Op Code PC6690 and release the vehicle. - If the inspection result is ?NG? (clip is not fully locked into place) - Take a photograph of the clip position and email it to: nnafqasupport@nissan-usa.com along with the following: - E-mail subject line: PC669 (Altima Fuel Feeder Tube Clip) - Attach Clear Pictures of the clip that is not locked into place. - Dealer Name: - Dealer Code: - Dealer Address:
NTB12-103f
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC665 2019 Altim
Service Bulletin/Repair Instructions
Wheel Cover Dealer Inventory *****Dealer Announcement***** Nissan is conducting a quality action to replace all four (4) wheel covers on 91 specific 2019 Altima vehicles identified in Service Comm. Due to a manufacturing issue that has since been corrected, the silver paint may peel away from the black base paint layer on two-tone wheel covers, when the wheel film is removed. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to complete this repair prior to sale to ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC665 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers should replace all four (4) of the wheel covers to remedy any vehicle subject to this quality action. - Nissan has developed an automatic parts shipment to provide parts to affected dealers. Please see the attached list to identify how many sets your dealership should receive. Orders will begin arriving at dealers by November 7, 2018 - If additional wheel covers are necessary, please order via normal means 3. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealer?s responsibility to check Service Comm or DBS National Service History ? Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.
PC665 Automatic
Service Bulletin/Repair Instructions
Automatic Parts Shipment List
PC666 2019 Altim
Service Bulletin/Repair Instructions
Front Exhaust Tube Dealer Inventory *****Dealer Announcement***** Nissan is conducting a quality action to inspect and, if necessary, replace the incorrect exhaust component on 31 specific 2019 Altima vehicles identified in Service Comm. Due to a manufacturing issue that has since been corrected, suspect units may have an incorrect front exhaust pipe installed. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC666. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers must use the attached procedure to inspect the vehicle. - If the first three digits are ?6CJ? submit a claim for the inspection and release the vehicle. - If the first three digits are ?6CL?, take a picture and provide the requested information listed below in an email to nnafqasupport@nissan-usa.com and await further instruction: - E-Mail Subject Line: PC666 Front Exhaust Tube - Attach Clear Picture as referenced in inspection instructions - Dealer Name: - Dealer Code: - Dealer Address: - VIN: - Contact Person Name: - Contact Person Phone Number: Note: Instructions and claims information will be provided within 48 hours.
PC663 2019 Altim
Service Bulletin/Repair Instructions
Electronic Control Module (ECM) Reprogram Dealer Inventory *****Dealer Announcement***** Nissan is issuing a quality hold and requiring dealers to update Electronic Control Module (ECM) software on 8,007 specific 2019 Altima vehicles identified in Service Comm. The current software installed may allow the Malfunction Indicator Lamp (MIL) to illuminate improperly during full throttle operation at high altitudes. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC663 ? New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ? Refer to NPSB 15-460 for additional information ? Please continue to check newly arriving inventory for campaign applicability. 2. Dealers must use the attached procedure to install the updated software prior to retail delivery of the vehicle to ensure emissions regulation compliance. 3. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealer?s responsibility to check Service Comm or DBS National Service History ? Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory. Thank you for your prompt attention to this matter. NISSAN NORTH AMERICA, INC. Aftersales DIVISION
NTB15-077b
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-018c
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.