Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB26-026
STEERING WHEEL SWITCH ILLUMINATION IS TOO DARK AT DUSK AND/OR DAWN IF YOU CONFIRM The customer states that the steering wheel switches are too dark at dusk and/or dawn. ACTION 1. Replace the Light & Rain Sensor. 2. Configure the BCM to "Mode 2" with CONSULT 4.
NTB09-131C
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB25-032B
HVAC INSUFFICIENT COOLING CONCERNS IF YOU CONFIRM The customer states a lack of comfort due to insufficient cooling, AND The outside ambient temperature is considered hot, for example around 40°C (104°F). ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current Amplifier-Control, Air Conditioner (A/C auto amp) part number. 2. Reprogram the A/C auto amp, if applicable. 3. Confirm the current Controller Assy – Refrigerator (Heat pump control unit) part number. 4. Reprogram the Controller Assy – Refrigerator (Heat pump control unit) after reprogramming the A/C auto amp, if applicable. 5. Erase all DTCs. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NPSB 15-460
ACTION Date: October 2, 2025 To: FOMs, DOMs, RAMs, & RGMs Subject: LAUNCH PD172 PMA55 Multi Model Monroney Bumper Label – QA – Dealer Announcement and Procedure ACTION: FOMs & DOMs are asked to ensure that dealers are aware of this new campaign information. Dealer Announcement: To ensure continued customer satisfaction and confidence, Nissan is conducting a quality action on certain specific model year 2025 ARIYA, 2024-2025 Pathfinder, 2024-2026 Rogue, 2024-2025 Murano and 2025-2026 Kicks vehicles, as identified in Service Comm and DBS National Service History. This action updates the Monroney labels to reflect corrected bumper labeling requirements for California and Hawaii. Dealers will replace original Monroney labels with corrected Monroney labels. Nissan will send VIN-specific corrected labels to address affected vehicles in dealer inventory. New labels will begin shipping via Federal Express Wednesday, October 1, 2025. Dealers will replace original Monroney labels with corrected Monroney labels. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History – Open Campaigns I.D. PD172 & PMA55 •New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). Refer to NPSB 15-460 for additional information •Some vehicles may still be in transit. Please continue to check newly arriving inventory for applicability. 2.Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3.Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4.If you have exchanged or traded one of the affected vehicles to another Nissan dealer, please forward the corrected Monroney label to the current dealer upon receipt so it can be attached to the vehicle. •If a vehicle has been retailed, dispose of the corrected Monroney label using the same procedure as for destroying the original Monroney label. 5.The service department should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle.
NTB24-009A
SIDE RADAR ALIGNMENT SERVICE INFORMATION The SERVICE INFORMATION in this bulletin can be used in conjunction with the ESM if experiencing difficulty while performing Side Radar alignment, including but not limited to the following DTCs: C1E50-54 - SIDE RADAR ALIGNMENT C1E50-78 - SIDE RADAR ALIGNMENT C1ED0-54 - SIDE RADAR ALIGNMENT C1ED0-78 - SIDE RADAR ALIGNMENT C1E10-54 - SIDE RADAR ALIGNMENT C1E10-78 - SIDE RADAR ALIGNMENT C1E90-54 - SIDE RADAR OFF-CENTER C1E90-78 - SIDE RADAR OFF-CENTER To increase the chance of successful completion of Side Radar alignment, follow the recommendations below: Ideal road conditions are long, straight two (2) lane roads with minimal stop signs/signals and some structures along the sides of the roads. Keep speeds between 20-40 MPH and avoid interstates. Minimize stops. Minimize driving below 13 MPH. Utilize a USB cable to connect CONSULT 4 to the VI. A continuous internet connection is not required to complete the alignment, only to start it. Side Radar LH and RH alignment may not proceed at the same rate to 100%. Continue Side Radar alignment if only one (1) LH or RH side displays 100% until BOTH LH and RH sides display 100%. HINT: If the above conditions are being met, the alignment will take approximately 30 minutes.
NTB24-040
VEHICLE NOT CHARGING THROUGH HIGH VOLTAGE CHARGE PORT IF YOU CONFIRM The vehicle is not charging from the level 3 high voltage charger, AND One (1) or two (2) Terminal Cap(s) are missing at the level 3 High Voltage Charge Port. ACTION Refer to the SERVICE PROCEDURE to: 1. Inspect the bottom two (2) terminals and check for missing Terminal Cap(s). 2. Replace any missing Terminal Cap(s) as needed. 3. Erase any DTCs using CONSULT 4. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB23-077A
ADAS DTC SERVICE INFORMATION SERVICE INFORMATION If one or more of the following ADAS (Advanced Driver Assistance System) DTCs are stored, but continue to be current after the vehicle is turned OFF (IGN OFF) and then back to Ready Mode (IGN ON), C1F90-97 – ADAS control unit 2 circuit C1F05-49 – Front camera unit C1F05-97 – Front camera unit C1F05-04 – Front camera unit U19BC-87 – CAN comm err (Side radar rear LH) U19BD-87 – CAN comm err (Side radar rear RH) U19C2-87 – Ethernet circuit ERROR(AVM) U19C7-87 – Ethernet comm err (HD map module) U19C6-87 – Ethernet comm err (Front camera) C21F6-49 – Camera C258E-86 – Steering Angle Sensor C2500-49 – Camera unit malf C2506-49 – Front camera unit U2159-87 – CAN communication error (steering control unit) C2540-04 – Backup mode C1F95-11 – System BU func power supply circ
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.