Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB23-081C
Service Campaign
VOLUNTARY SAFETY RECALL CAMPAIGN 2005-2013 FRONTIER, PATHFINDER, AND XTERRA; DRIVER AIR BAG COVER CAMPAIGN ID #: PC945 and PC948 APPLIED VEHICLES: 2005-2013 Frontier (D40) 2005-2012 Pathfinder (R51) 2005-2013 Xterra (N50) Check Service COMM or Dealer Business Systems (DBS) National Service History to confirm campaign eligibility. INTRODUCTION Nissan is conducting this voluntary safety recall campaign on certain specific model year 2005-2012 Pathfinder, and 2005-2013 Frontier and Xterra vehicles to inspect and, if necessary, replace the Driver Air Bag Cover. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC945 and PC948 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer’s responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer’s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-079G
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0448 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
DOR-M3J3F-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
DOR-M9J4S-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
NTB15-079e
Service Bulletin/Repair Instructions
2005-2019 FRONTIER; MIL ON WITH DTC P0448 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-026
Service Bulletin/Repair Instructions
2005-2019 FRONTIER; HIGH-MOUNTED STOP LAMP SERVICE PART SERVICE INFORMATION The mounting stud diameter for the high-mounted stop lamp service part has changed from 5 mm to a 6 mm. If for any reason the high-mounted stop lamp needs to be replaced, the mounting hole will need to be enlarged to 6.5 mm (¼ inch) as follows: 1. Remove the high-mounted stop lamp. ï· - For high-mounted stop lamp removal, refer to the Electronic Service Manual: Section DRIVER CONTROLS > EXTERIOR LIGHTING SYSTEM > REMOVAL AND INSTALLATION > STOP LAMP. 2. Enlarge the high-mounted stop lampâs mounting holes (see Figure 1 on page 2) using a 6.5 mm (¼ inch) drill bit. NOTICE: To avoid damage to the vehicle, apply light pressure to the drill while drilling. Excessive force may cause the drill bit to penetrate too far and damage the headliner. 3. Apply touch-up paint to the mounting holes to protect the bare metal. 4. Install the new high-mounted stop lamp using M6 mounting nuts. Refer to the PARTS INFORMATION on page 2.
NTB15-079d
Service Bulletin/Repair Instructions
2005-2019 FRONTIER; MIL ON WITH DTC P0448 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-030a
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB18-080
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
REVISION 3_P7318
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Voluntary Service Campaign UPDATE January 5, 2018 The announcement from October 6, 2017 has been revised: - Dealers may now use revised TSB NTB17-070 to resume repair of 2004-2006 model year vehicles. Please discard previous versions of this bulletin
NTB17-070a
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2004-2011 TITAN, AND 2005-2011 FRONTIER AND XTERRA; AIR BAG DIAGNOSIS SENSOR UNIT This bulletin has been amended. The reprogramming procedure has been revised. No other changes have been made. Discard all previous versions of this bulletin.
P7318
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Voluntary Service Campaign UPDATE October 6, 2017 The announcement from August 15, 2017 has been revised to include: - Claims information for unintended airbag deployment (related to campaign) Temporary suspension of this campaign on all affected 2004-2006 model year vehicles is still in affect - Nissan is aware of reprogramming concerns on 2004-2006 models subject to P7318 Air Bag Control Unit Reprogramming and is working diligently with the supplier to provide a solution. - In the interim, Nissan recommends dealers suspend reprogramming activity on all 2004-2006 models until a software remedy is available. These models will continue to be identified in Service Comm and DBS National Service History with an open P7318 campaign. Nissan will provide an update as soon as revised software is available. Please discard previous versions of this bulletin
NTB17-082a
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
REV1_P7318
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Voluntary Service Campaign Temporary suspension of this campaign on all affected 2004-2006 model year vehicles. Nissan is aware of reprogramming concerns on 2004-2006 models subject to P7318 Air Bag Control Unit Reprogramming and is working diligently with the supplier to provide a solution. In the interim, Nissan recommends dealers suspend reprogramming activity on all 2004-2006 models until a software remedy is available. These models will continue to be identified in Service Comm and DBS National Service History with an open P7318 campaign. Nissan will provide an update as soon as revised software is available. Please discard previous versions of this bulletin.
P7318a
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Software Update Notice ***** Campaign Update***** Updated software has been released to ASIST at 3:00 PM Central Time to address concerns with some vehicles not being able to complete the reprogramming. This software will be released automatically overnight, but dealers can download the new software immediately by manually syncing their ASIST on their CONSULT III to acquire the latest updates.
P7318b
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Voluntary Service Campaign ***** Campaign Summary***** Nissan is committed to customer satisfaction. Nissan is conducting a Voluntary Service Campaign to reprogram the Air Bag Control Unit (ACU) in 2004-2014 Titan, 2005-2014 Frontier, and 2005-2014 Xterra vehicles. The current ACU rollover-sensing calibration logic could allow for unintended curtain air bag deployment in rare instances occurring under certain unique driving scenarios, usually involving unpaved roads or off-road where one side of the vehicle is higher than the other. The ACU reprogramming will improve rollover-sensing calibration to address certain unique driving scenarios, and help prevent unintended curtain air bag deployment, while maintaining the design intent for deployment in rollover crashes. Owners of affected vehicles will be notified beginning in June 2017 and asked to bring their vehicle to an authorized Nissan dealer to have the remedy work completed at no cost to the owner.
NTB17-070
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2004-2011 TITAN, AND 2005-2011 FRONTIER AND XTERRA; AIR BAG DIAGNOSIS SENSOR UNIT INTRODUCTION Nissan is conducting a voluntary service campaign on certain specific model year 2004- 2011 Titan, and 2005-2011 Frontier and Xterra vehicles to reprogram the air bag diagnosis sensor unit. This repair will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P7318 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
NTB17-030
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
NTB17-026
Service Bulletin/Repair Instructions
BALL JOINT AXIAL END PLAY PROCEDURE SERVICE INFORMATION When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.
NTB14-068b
Service Bulletin/Repair Instructions
POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.
NTB15-079c
Service Bulletin/Repair Instructions
2005-2015 FRONTIER; MIL ON WITH DTC P0448 This bulletin has been amended to add steps to apply EPT foam to seal the fuel filler pipe and other minor changes made throughout. Please discard previous versions of this bulletin.
NTB14033B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Nissan electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.
NTB09099A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB15079A
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The MIL is ON with DTC P0448 (EVAP canister vent control valve close) stored in the ECM. ACTION: 1. Replace the EVAP canister (canister) and EVAP canister vent control valve (vent control valve). 2. Remove the canister filter. 3. Attach the EPT foam seal to fuel filler tube. 4. Replace the fuel filler pipe, canister drain hose, and fuel filler cap (on some model years) listed in PARTS INFORMATION. 5. Erase the DTC. See this bulletin for further detail.
NTB09081C
Service Bulletin/Repair Instructions
SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NTB15107
Service Bulletin/Repair Instructions
IF YOU CONFIRM: A remanufactured automatic transmission supplied by ATC Drivetrain is installed in an APPLIED VEHICLE AND CONSULT-III plus (C-III plus) is not able to communicate with the TCM through Diagnosis (One System) OR C-III plus is able to communicate with the TCM, but the TCM part number?s (P/N) sixth digit is a "5", "6", or "7" (for example, 31020-7xxxx). NOTE: To determine if an applied vehicle is equipped with an ATC Drivetrain remanufactured A/T, see page 3. ACTION: Refer to the Flow Chart on page 2. See this bulletin for further detail.
NTB13028A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NTB14068A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
NTB13088A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
NTB15060
Service Bulletin/Repair Instructions
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB15055
Service Bulletin/Repair Instructions
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB12078A
Service Bulletin/Repair Instructions
SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
NTB00042D
Service Bulletin/Repair Instructions
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB11021A
Service Bulletin/Repair Instructions
IF YOU CONFIRM: Squeal/Squeak noise from the front brakes: While moving forward or reverse, with very light brake application (pedal pressure), after the vehicle has been sitting, typically overnight ("cold" brakes), at speeds less than 10 MPH, while traveling straight or turning. ACTION: Replace the hardware on both front brake calipers with the kit listed in the Parts Information in this bulletin. See this bulletin for further detail.
NTB14107
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
NTB10066A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NTB13081A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The specifications for the intake and exhaust valves and valve lifter service parts have been changed. * The valve stem length of both intake and exhaust valve has been increased (Figure 1) and are a direct replacement for the shorter style valve. * The related valve lifter cup has been shortened (Figure 2) and the point at which the valve lifter contacts the valve stem has been shortened (not shown). These service parts will require that the valve and valve lifter be replaced at the same time. See this bulletin for further details.
NTB-08-055-A
Service Bulletin/Repair Instructions
NISSAN: SRS PRECAUTIONS DURING SERVICE;IMPROPER MAINTENANCE, INCLUDING INCORRECT REMOVAL AND INSTALLATION OF THE SRS, CAN LEAD TO A SERIOUS INJURY OR DEATH CAUSED BY UNINTENTIONAL ACTIVATION OF THE SRS ON ALL NISSAN MODELS WITH THE SRS SYSTEMS. *PE UPDATED 2/21/14. *PE
NTB08055C
Service Bulletin/Repair Instructions
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB-03-074-C
Service Bulletin/Repair Instructions
NISSAN: EXTERIOR LAMP FOGGING. OCCASIONALLY WATER IS NOTICED IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). THIS IS NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. THE FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. NO MODELS LISTED. *PE UPDATED 5/7/10. *PE UPDATED 12/9/13. *PE
NTB-09-020-F
Service Bulletin/Repair Instructions
NISSAN: A LOOSE FUEL FILL CAP IS THE CAUSE OF EVAP LEAK DTCS (P0442, P0455, P0456) STORED ON SOME VEHICLES. MODEL YEARS 2007-2011. MODEL NOT LISTED. *PE
NTB09020F
Service Bulletin/Repair Instructions
SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.
NTB92123D
Service Bulletin/Repair Instructions
Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
NTB13027A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
NTB00033E
Service Bulletin/Repair Instructions
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
NTB04094A
Service Bulletin/Repair Instructions
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
NTB98018G
Service Bulletin/Repair Instructions
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
NTB-13-038
Service Bulletin/Repair Instructions
NISSAN: LOCK/UNLOCK REQUEST BUTTON ON OUTSIDE HANDLE DOES NOT RESPOND. *JS
NTB99001A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
NTB11012B
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
MAILM
Service Bulletin/Repair Instructions
Nissan has decided in the interest of customer satisfaction, to further extend the warranty for the Radiator Assembly on all 2005-10 Frontier, Pathfinder, and Xterra vehicles equipped with automatic transmissions.
NPSB-12-063
Service Bulletin/Repair Instructions
NISSAN: CONSUMER ALERT ISSUED, REGARDING COUNTERFEIT AIR BAGS AND DANGER OF USING, INSTALLING OR REPLACING, IN VEHICLES AND AIR BAGS FAILS TO MEET STANDARDS OF RELIABILITY, QUALITY, AND DURABILITY OF GENUINE PARTS. NO MODELS OR YEARS LISTED. *PE
NTB-10-102-A
Service Bulletin/Repair Instructions
NISSAN: BULLETIN REGARDING DIAGNOSIS OF ABS/VDC WHEEL SPEED SENSOR. MODEL 2007-2013 NISSAN. *PE
NTB12-035
Service Bulletin/Repair Instructions
NISSAN: ECM REPLACEMENT PROCEDURES WITH CONSULT III PLUS. APPLIES TO ALL 2004 AND LATER (DOES NOT APPLY TO LEAF/EV) VEHICLES. *JS
NTB12-027
Service Bulletin/Repair Instructions
NISSAN: PATHFINDER, XTERRA, AND FRONTIER; POWER STEERING HOSE SERVICE PART CHANGE. *JS
NTB12-009
Service Bulletin/Repair Instructions
NISSAN: DOOR LOCK/UNLOCK INOPERATIVE WITH INTELLIGENT KEY. *KB
NTB-07-069C
Service Bulletin/Repair Instructions
NISSAN: FUEL GAUGE ISSUES AND/OR DTC P0461/2/3. THE FUEL GAUGE IS ERRATIC, INACCURATE, OR INOPERATIVE. THE MIL IS ON WITH DTC P0461, P0462, OR P0463 STORED IN SELF DIAGNOSIS. REPLACE THE FUEL LEVEL SENDING UNIT WITH THE ONE FROM THE PARTS INFORMATION SECTION. *PE UPDATED 1/24/11. *PE AMENDMENT UPDATED. 2/28/11. *PE
NTB-10-072A
Service Bulletin/Repair Instructions
NISSAN: FRONT SUSPENSION NOISE. A NOISE (CLUNKING, SQUEAKING, POPPING) CAN BE HEARD WHEN PERFORMING AT LEAST ONE OF THE FOLLOWING ACTIONS: TURNING THE STEERING WHEEL LEFT OR RIGHT, DRIVING OVER SPEED BUMPS, DRIVING ON ROUGH ROADS, ACCELERATING OR DECELERATING AND NOISE IS COMING FROM THE FRONT STABILIZER BAR BUSHING. *PE
NTB-09-101
Service Bulletin/Repair Instructions
NISSAN: TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON/FLASHING. NO MODELS OR MODEL YEARS LISTED. *PE UPDATED ON 08-11-2011. *KB
NTB-10-115
Service Bulletin/Repair Instructions
NISSAN: POWER STEERING OIL COOLER SERVICE. IF A POWER STEERING OIL COOLER NEEDS TO BE REPLACED FOR ANY REASON, PLEASE REFER TO THE SERVICE PROCEDURE. *PE
NTB-09-129
Service Bulletin/Repair Instructions
NISSAN: VENT CONTROL VALVE REPLACEMENT. WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE
NTB-10-061
Service Bulletin/Repair Instructions
NISSAN: XENON HEAD LAMP SERVICE. A XENON HEADLAMP IS NOT FUNCTIONING BECAUSE OF AN ISSUE INSIDE THE HEADLAMP ASSEMBLY (AN INTERNAL ISSUE). IN MOST CASES, REPLACEMENT OF A BULB OR HID CONTROL UNIT WILL SOLVE THE INCIDENT. THIS INCLUDES ALL MODELS WITH XENON HEAD LAMPS. NO MODELS LISTED. *PE
NTB-10-055
Service Bulletin/Repair Instructions
NISSAN: BLOWER MOTOR DOES NOT WORK. THE BLOWER MOTOR FOR HEATER AND AIR CONDITIONER DOES NOT OPERATE. THERE ARE SIGNS OF WATER INTRUSION IN THE BLOWER MOTOR. *PE
NTB-04-047
Service Bulletin/Repair Instructions
NISSAN: OIL LEAKING FROM TRANSFER CASE. OIL IS LEAKING FROM ONE OR A COMBINATION OF THREE BOLTS AT THE REAR OF THE TRANSFER CASE. IF BOLTS ARE NOT MISSING, DO NOT REPLACE TRANSFER CASE, TRANSFER CONTROL DEVICE; OR TRANSFER CONTROL UNIT FOR THIS INCIDENT, IT SHOULD OCCUR. *PE
NTB-10-008
Service Bulletin/Repair Instructions
NISSAN: REAR AXLE SEAL LEAKS. THE REAR AXLE ASSEMBLY IS LEAKING GEAR OIL FROM THE RIGHT AND/OR LEFT HAND AXLE SEAL, AND THE VEHICLE IS EQUIPPED WITH A M226 STYLE AXLE AND NO NOISE OR VIBRATION IS COMING FROM THE REAR FINAL DRIVE GEARS AND SIDE BEARINGS. *PE
NTB-09-030
Service Bulletin/Repair Instructions
NISSAN: THE 12 VOLT BATTERY IS AN IMPORTANT PART OF THE VEHICLE ELECTRICAL SYSTEM AND IS REQUIRED TO STAY CONNECTED WHEN THE ENGINE IS RUNNING. TO PREVENT DAMAGE TO VEHICLE ELECTRONIC COMPONENTS FOLLOW THE INSTRUCTIONS/CAUTIONS. NO MODEL YEARS LISTED. *PE
NTB08-062
Service Bulletin/Repair Instructions
SEAT BACK BOARD REMOVAL/INSTALLATION. *NJ
NTB08-063
Service Bulletin/Repair Instructions
RIGHT FRONT SEAT BACK VIBRATION AT HIGHWAY SPEEDS. *NJ
NTB08-049
Service Bulletin/Repair Instructions
NISSAN; SPECIAL AUTOMATIC TRANSMISSION FLUID REQUIREMENT. 2004 TO CURRENT NISSAN VEHICLES. *NJ
07042
Service Bulletin/Repair Instructions
BUZZING/WHINING NOISE FROM TIMING CHAIN AREA. *KB
03030
Service Bulletin/Repair Instructions
EXTERIOR LAMP FOGGING. *KB