Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB20-016G
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016F
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-010C
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB22-087
Service Bulletin/Repair Instructions
NOISE AND/OR VIBRATION FROM FRONT OR REAR PROPELLER SHAFT SERVICE INFORMATION If you confirm abnormal noise and/or vibration is coming from the front or rear propeller shaft of an APPLIED VEHICLE, inspect the propeller shaft journals (U-Joints) for binding and/or abnormal noise before replacing the propeller shaft. If binding and/or abnormal noise is confirmed from the propeller shaft U-Joints, replace the propeller shaft U-Joints. Refer to the ESM for the propeller shaft U-Joint replacement procedure. NOTE: Replacement of the propeller shaft due to noise and/or vibration caused by the propeller shaft U-Joints may result in warranty charge back.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-079G
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0448 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-103D
Service Bulletin/Repair Instructions
MANUAL SEAT TRACK ADJUSTMENT DOES NOT LOCK INTO POSITION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-018D
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB20-016E
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016d
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016c
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-103c
Service Bulletin/Repair Instructions
2014 â 2020 FRONTIER; MANUAL SEAT TRACK ADJUSTMENT DOES NOT LOCK INTO POSITION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016b
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016a
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-079e
Service Bulletin/Repair Instructions
2005-2019 FRONTIER; MIL ON WITH DTC P0448 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-026
Service Bulletin/Repair Instructions
2005-2019 FRONTIER; HIGH-MOUNTED STOP LAMP SERVICE PART SERVICE INFORMATION The mounting stud diameter for the high-mounted stop lamp service part has changed from 5 mm to a 6 mm. If for any reason the high-mounted stop lamp needs to be replaced, the mounting hole will need to be enlarged to 6.5 mm (¼ inch) as follows: 1. Remove the high-mounted stop lamp. ï· - For high-mounted stop lamp removal, refer to the Electronic Service Manual: Section DRIVER CONTROLS > EXTERIOR LIGHTING SYSTEM > REMOVAL AND INSTALLATION > STOP LAMP. 2. Enlarge the high-mounted stop lampâs mounting holes (see Figure 1 on page 2) using a 6.5 mm (¼ inch) drill bit. NOTICE: To avoid damage to the vehicle, apply light pressure to the drill while drilling. Excessive force may cause the drill bit to penetrate too far and damage the headliner. 3. Apply touch-up paint to the mounting holes to protect the bare metal. 4. Install the new high-mounted stop lamp using M6 mounting nuts. Refer to the PARTS INFORMATION on page 2.
PC704 Frontier_N
Service Bulletin/Repair Instructions
Engine Crankshaft Inspection *****Dealer Announcement***** Nissan is conducting a quality action on 186 specific MY 2019 Frontier and 83 NV vehicles identified in Service Comm, to remove and inspect the engine crankshaft counterweight surface for an impact mark. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC704 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, sell or trade the specific vehicles in Dealer Inventory subject to this Quality Action. 3. Use the attached procedure to inspect the vehicle. - If an impact mark is not found on the counterweight machined surface, reassemble vehicle per the Electronic Service Manual (ESM). - File a claim for the inspection, and release the vehicle for sale - If an impact mark is located on machined surface area of the counterweight when the crankshaft pulley notches are in the indicated positions, provide the requested information via ASIST/Tech Support Info/Powertrain Call Center Pre-Call forms/New Engine Form as per the attached instructions and HOLD the vehicle. - Do not file a claim
NTB19-022
Service Bulletin/Repair Instructions
NISSAN; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.
NTB19-021
Service Bulletin/Repair Instructions
NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
NTB16-103b
Service Bulletin/Repair Instructions
2014 ? 2019 FRONTIER; MANUAL SEAT TRACK ADJUSTMENT DOES NOT LOCK INTO POSITION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-079d
Service Bulletin/Repair Instructions
2005-2019 FRONTIER; MIL ON WITH DTC P0448 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-080
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-018c
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.