Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB23-048A
Service Bulletin/Repair Instructions
DTC P17F4 STORED IN THE TCM IF YOU CONFIRM The customer reports transmission vibration when accelerating, HINT: Vibration occurs during quick reacceleration after braking, during a 2-1 downshift of the auxiliary gearbox. AND DTC P17F4 for “AUXILIARY GEARBOX (CL JUDDER)” is stored in the TCM. · If DTCs other than P17F4 are stored, this bulletin does not apply. Refer to the ESM for further diagnostic information. ACTION Refer to the Repair Overview on page 2 to determine if this bulletin applies. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB22-027B
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. CONSULT has been updated to allow DTC B2E01-96 for “Internal battery” to be cleared in the TCU. If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-038C
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB24-002A
Service Bulletin/Repair Instructions
DTCS C1B53-04 AND/OR C1B54-04 STORED IN THE ADAS CONTROL MODULE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB21-078B
Service Bulletin/Repair Instructions
HIGH FREQUENCY NOISE WITH AUDIO SYSTEM DISPLAY ON This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB24-002
Service Bulletin/Repair Instructions
DTCS C1B53-04 AND/OR C1B54-04 STORED IN THE ADAS CONTROL MODULE IF YOU CONFIRM DTCs C1B53-04 for âSIDE RDR R MALFâ and/or C1B54-04 for âSIDE RDR L MALFâ are stored as CURRENT in the ADAS Control Module. AND The ESM diagnosis leads to Side Radar Sensor replacement. ACTION If replacing one or more affected Side Radar Sensor(s), refer to the SERVICE PROCEDURE in this bulletin to apply a strip of foam around each of the Side Radar Sensors before reinstalling the rear bumper fascia. HINT: This bulletin does not cover the diagnosis or replacement of the Side Radar Sensors.
NTB22-105B
Service Bulletin/Repair Instructions
REDUCED POWER AFTER COLD START AT BELOW FREEZING TEMPERATURES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051B
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB23-048
Service Bulletin/Repair Instructions
DTC P17F4 STORED IN TCM IF YOU CONFIRM The customer reports transmission vibration when accelerating, HINT: Vibration occurs during quick reacceleration after braking, during a 2-1 downshift of the auxiliary gearbox. AND DTC P17F4 for âAUXILIARY GEARBOX (CL JUDDER)â is stored in the TCM. ï· If DTCs other than P17F4 are stored, this bulletin does not apply. Refer to the ESM for further diagnostic information. ACTION Refer to the Repair Overview on page 2 to determine if this bulletin applies.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-038
Service Bulletin/Repair Instructions
WARNING LIGHT ON WITH DTC C111F STORED AS CRNT IN THE ABS IF YOU CONFIRM DTC C111F (G-SENSOR) is stored as âCRNTâ in the ABS Actuator and Electric Unit (Control Unit). IMPORTANT: Do not replace the ABS control unit unless instructed to do so. ACTION Refer to the SERVICE PROCEDURE on page 2 to calibrate the Decel G-Sensor.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-078A
Service Bulletin/Repair Instructions
HIGH FREQUENCY NOISE WITH AUDIO SYSTEM DISPLAY ON This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-028B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-021A
Service Bulletin/Repair Instructions
DTC P0746, P0776, P0841, P0965, P17F0 AND/OR P17F1 STORED IN THE TCM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-010C
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051A
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-085B
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-027A
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB20-029F
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB22-018A
Service Bulletin/Repair Instructions
MANUAL FRONT SEAT DOES NOT MOVE FORWARD/REARWARD This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-028A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051
Service Bulletin/Repair Instructions
HORN INOPERATIVE IF YOU CONFIRM The horn on an APPLIED VEHICLE is inoperative. ACTION Inspect the horn pad for a pinched ground wire. If a pinched ground wire is found, replace the high and low horns.
NTB22-034
Service Bulletin/Repair Instructions
ROCKFORD PREMIUM AUDIO KIT DTCS STORED IN INFOTAINMENT HEAD UNIT SERVICE INFORMATION The following DTCs may be stored in the infotainment head unit of an APPLIED VEHICLE that a Rockford Premium Audio Kit (dealer/port accessory, Figure 1 on page 2) has been installed. These DTCs do not indicate a malfunction of the system, and shall be ignored. ï· B130B-13 â (Rear RH speaker -or- Rear Right Speaker Open Load) ï· B130D-13 â (Front RH speaker -or- Front Right Speaker Open Load) ï· B130F-13 â (Front LH speaker -or- Front Left Speaker Open Load) ï· B1311-13 â (Rear LH speaker -or- Rear Left Speaker Open Load) NOTE: o These DTCs will all appear together and cannot be permanently erased. o If sound is not coming out of one or more speakers, refer to the ESM for additional diagnostic information.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-085A
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-028
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION IMPORTANT: ï· For Sentra, if Service Comm shows that PM991 applies to the vehicle you are working on, perform PM991 and do not apply this bulletin. ï· Refer to NTB21-038 to verify if the customer concern is a Hardware or Software related issue. This bulletin does not apply to hardware issues. The software update in the following SERVICE PROCEDURE is to address the items below: ï· Stability improvements and "bug" fixes ï· High Frequency noise with audio system display ON Refer to steps 1 - 5 starting on page 3 to confirm that this bulletin applies.
NTB22-027
Service Bulletin/Repair Instructions
B2E01-96 (INTERNAL BATTERY) DTC STORED AS CURRENT IN IVC SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 (Internal battery) to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and No additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEURE starting on page 2.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB19-040H
Service Bulletin/Repair Instructions
DTC P0741/4/6, P0776, P0841, P0875, P0965, P2857/8/9, P17F0/1/2/4 AND/OR P285A STORED IN THE TCM, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been superseded. If one or more of the following DTCs is stored, refer to NTB22-021. ï· P0746 â PRESSURE CONTROL SOLENOID A ï· P0776 â PRESSURE CONTROL SOLENOID B ï· P0965 â PRESSURE CONTROL SOLENOID B ï· P17F0 â CVT JUDDER (T/M INSPECTION) ï· P17F1 â CVT JUDDER (C/V INSPECTION) ï· P285A â CLUTCH B PRESSURE ï· P0875 â T/M FLUID PRESS SENSOR/SWITCH D If one or more of the following DTCs is stored, refer to the ESM: ï· P0741 â TORQUE CONVERTER ï· P0744 â TORQUE CONVERTER ï· P0841 â TRANSMISSION FLUID PRESSURE SEN/SW A ï· P17F2 â CVT JUDDER (T/C INSPECTION) ï· P17F4 â AUXILIARY GEARBOX (CLUTCH JUDDER) ï· P2857 â CLUTCH A PRESSURE ï· P2858 â CLUTCH B PRESSURE ï· P2859 â CLUTCH A PRESSURE Please discard previous versions of this bulletin.
NTB22-021
Service Bulletin/Repair Instructions
DTC P0746, P0776, P0841, P0965, P17F0 AND/OR P17F1 STORED IN THE TCM IF YOU CONFIRM One or more of the following DTCs are stored: ï· P0746 â PRESSURE CONTROL SOLENOID A ï· P0776 â PRESSURE CONTROL SOLENOID B ï· P0841 â TRANSMISSION FLUID PRESSURE SEN/SW A ï· P0875 â T/M FLUID PRESS SENSOR/SWITCH ï· P0965 â PRESSURE CONTROL SOLENOID B ï· P17F0 â CVT JUDDER (T/M INSPECTION) ï· P17F1 â CVT JUDDER (C/V INSPECTION) ï· P17F2 â CVT JUDDER (T/C INSPECTION) ï· P2857 â CLUTCH A PRESSURE ï· P2858 â CLUTCH B PRESSURE ï· P2859 â CLUTCH A PRESSURE ï· P285A â CLUTCH B PRESSURE IMPORTANT: ï· If DTCs are stored other than those listed above, this bulletin does not apply. ï· If DTCs P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. ï· If ONLY P0875 T/M FLUID PRESS SENSOR/SWITCH is stored, refer to the ESM. ï· NTB20-060, 2018-2019 Kicks; Enhanced Diagnostic Logic For CVT, has reprogramming instructions that may apply. ACTION Refer to the REPAIR OVERVIEW on page 2.
PMA04 2021 Kicks
Service Bulletin/Repair Instructions
Steering Column Dealer Inventory ***** Dealer Announcement ***** Nissan is now updating the temporary hold on 6 specific model year 2021 Kicks® vehicles identified in Service Comm to a dealer inventory quality action. Dealers will inspect the steering column torque sensor lot code and, if necessary, replace the steering column assembly. Due to a supplier manufacturing concern, vehicles may lose Steering Assist. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. ***** What Dealers Should Do ***** PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PMA04 ⢠New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ⢠Refer to NPSB 15-460 for additional information ⢠Some vehicles may still be in transit. Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4. Once remedied, dealers should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle for sale.
NTB20-029E
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB19-040G
Service Bulletin/Repair Instructions
DTC P0741/4/6, P0776, P0841, P0875, P0965, P2857/8/9, P17F0/1/2/4 AND/OR P285A STORED IN THE TCM, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-078
Service Bulletin/Repair Instructions
HIGH FREQUENCY NOISE WITH AUDIO SYSTEM DISPLAY ON IF YOU CONFIRM There is a high frequency (17 kHz) noise with the audio system display screen turned ON, NOTE: ï· The 17kHz range may not be audible to some people. ï· Noise can be heard with the audio system ON or OFF. AND The high frequency noise is not heard with the audio system display screen turned OFF. ACTION 1. Confirm the current Audio Control Unit software version is numerically below software version 423. 2. Update the Audio Control Unit software version to 423.
NTB21-070
Service Bulletin/Repair Instructions
LOCATION OF INTELLIGENT KEYS DURING PDI SERVICE INFORMATION The APPLIED VEHICLES built after August 1, 2021 will arrive at dealerships with the Intelligent Keys concealed under the rear seat. To locate the Intelligent Keys during PDI: ï· Open the driverâs side (LH) rear door, and then ï· Raise the corner of the rear seat.
PM988 2021 Kicks
Service Bulletin/Repair Instructions
Windshield Inspection Dealer Inventory *****Dealer Announcement***** Nissan is conducting a quality action to inspect the front windshield for a water leak and, if necessary, replace the windshield on 39 specific model year 2021 Nissan Kicks vehicles. Due to a manufacturing concern that has since been corrected, the urethane application on the left upper corner to the windshield may not adhere to the body primer. This condition may allow water to leak into the cabin. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PM988 ⢠New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information ⢠Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. ⢠If an affected vehicle was inadvertently traded, this information should be forwarded to the new dealer. 3. Use the attached procedure to inspect the windshield and, if necessary, remedy any vehicles affected by this quality action: ⢠Dealers have the option to sublet the repair (up to $150 sublet allowance is available). 4. The service department should submit the applicable warranty claim for the action performed to close the campaign on Service Comm and release the vehicle.
NTB19-040F
Service Bulletin/Repair Instructions
DTC P0741/4/6, P0776, P0841, P0875, P0965, P2857/8/9, P17F0/1/2/4 AND/OR P285A STORED, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-049
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0101 AND/OR P0507 STORED IN THE ECM IF YOU CONFIRM The MIL is ON and DTC P0101 (MAF SENSOR) and/or P0507 (ISC SYSTEM) is stored in the ECM. ACTION 1. Test the vehicle's 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs. 3. Perform Idle Air Volume Learning (IAVL).
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-118B
Service Bulletin/Repair Instructions
ALTIMA, KICKS AND VERSA SEDAN; DTC B26FE IN BCM AND KEY SYSTEM ERROR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
PM979 2021 Kicks
Service Bulletin/Repair Instructions
Telematics Reprogram Dealer Inventory *****Dealer Announcement***** Nissan is conducting a quality action to update the Telematics (Audio Control Unit) software on 418 specific model year 2021 Nissan Kicks (P15) due to a program logic concern. The telematics vehicle message features for Breakdown Call, Over the Air (OTA) and Remote Data Wipe may be inoperative. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PM979 ⢠New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information ⢠Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to update the Audio Control Unit software on any vehicles affected by this quality action. 3. The service department should submit the applicable warranty claim for the action performed to close the campaign on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.
NTB20-029D
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB21-027
Service Bulletin/Repair Instructions
MIL ON WITH DTC P062F AND/OR P0603 STORED IF YOU CONFIRM The MIL is ON and DTC P062F (EEPROM) and/or P0603 (ECM BACK UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicleâs 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.
NTB19-118A
Service Bulletin/Repair Instructions
ALTIMA, KICKS AND VERSA SEDAN; DTC B26FE IN BCM AND KEY SYSTEM ERROR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-040E
Service Bulletin/Repair Instructions
DTC P0741/4/6, P0776, P0841, P0965, P2857/8/9, P17F0/1/2/4 AND/OR P285A STORED, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL SERVICE INFORMATION If an Applied Vehicle needs to have a front axle nut removed, for any reason, the staking of the nut into the axle keyway must first be removed. The essential tool (part number # J-52982, Figure 1) required to remove the nut staking, is called out as a âCape Chiselâ in the Electronic Service Manual (ESM), and must be used to prevent thread damage to the axle (see Figure 2 on page 2). ï· The Cape Chisel arrived at dealers in December of 2020. ï· Damaged threads, due to improper removal of the stake placed in the nut, will not be covered by warranty. For information on using the Cape Chisel, refer to the Electronic Service Manual (ESM): Section TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT > LH/RH.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-009
Service Bulletin/Repair Instructions
DTC B12A3-72 FOR FUEL PUMP RELAY STUCK OPEN SERVICE INFORMATION DTC B12A3-72 (Fuel Pump Relay Stuck Open) may be stored when the IPDM monitor circuit internally sees 0V to ground at pin #46. This is caused by an internal short to ground in the IPDM or one of the IPDM fuses listed below is open. If B12A3-72 is current or reoccurs after erasing DTCs, inspect the model specific fuse first. If the fuse is not open replace the IPDM. ï· Altima â Fuse # 58 (page 2) ï· Kicks â Fuse # 54 (page 3) ï· Versa â Fuse # 61 (page 4) For additional IPDM diagnostic information refer to the Electronic Service Manual (ESM): Section ELECTRICAL & POWER CONTROL > POWER CONTROL SYSTEM > IPDM E/R. See model specific fuse locations starting on page 2.
NTB20-085
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION SERVICE INFORMATION The Telematics Control Unit (TCU) has the ability to send an automatic collision notification when the vehicle is involved in an accident. Once an automatic collision notification is performed, the function becomes disabled. The TCU must be reset to re-enable the automatic collision notification function. This bulletin describes how to reset the TCU after an automatic collision notification has been performed.
NTB19-042a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.