Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB15-049CC
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION HINT: This bulletin applies to vehicles equipped with a 4G network compatible TCU. TCUs compatible with 3G network only are no longer supported. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the NissanConnect® Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. · A table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. · A CHECK-OFF SHEET has been provided on page 20 to print and check off steps as they are performed. Staple the completed CHECK-OFF SHEET to the repair order.
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB24-048
Service Bulletin/Repair Instructions
*****Dealer Announcement***** Nissan is conducting a service campaign on certain specific MY2018-2025 Nissan LEAF vehicles identified in Service Comm and National Service History – Open Campaigns. On affected vehicles, at temperatures below -10°C/14°F, use of the blower motor at full speed can cause the defrost function to operate at a low electrical current and trigger failsafe logic. This may result in reduced defrost performance. Dealers will update the HVAC control software. *****What Dealers Should Do***** 1. Verify if vehicles are affected by this service campaign using Service Comm or DBS National Service History – Open Campaigns I.D. P4A17 • New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). Refer to NPSB 15-460 for additional information • Please continue to check newly arriving inventory for campaign applicability. 2. If a retailed vehicle affected by this Campaign ID visits the dealer for service, the dealer should inform the customer about the service campaign and communicate that the updated software is available. 3. Once remedied, dealers should submit the applicable warranty claim for the action performed so it can be closed in Service Comm and release the vehicle to the customer.
NTB20-066C
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. For all other models/model years, consult the Electronic Service Manual (ESM).
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB24-034
Service Bulletin/Repair Instructions
Subject: REVISION 2 R23D7 2018-2022 LEAF Rear View Camera Inspection - NCIR - Dealer Announcement REVISION 2 Please discard earlier versions of this bulletin. The announcement from May 20, 2024 has been revised to include the following: • The remedy and parts are now available, please refer to NTB24-034 to remedy any vehicle affected by this campaign Parts for this campaign are on restriction and can be ordered via DBS. The parts restriction will be removed and dealers can order, as needed, via normal ordering process beginning July 19, 2024. Part number 24271-ZW40A (Protector Harness Kit) will be automatically shipped to dealers beginning July 1, 2024. The Protector Harness Kit will repair seven (7) vehicles. • The “Service Parts Return” section in this dealer announcement has updated part numbers Nissan is requesting dealers to check their parts inventories for any of the part numbers listed in the table below under the “Service Parts Return” section, and if found, return these parts immediately using the instructions provided in this dealer announcement. If any of these parts are found in inventory, do not sell this part or install this part on any vehicle.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB24-012
Service Bulletin/Repair Instructions
DTC P18B1 STORED IN THE SHIFT CONTROL UNIT IF YOU CONFIRM DTC P18B1 for âCONTROL MODULEâ is stored in the Shift Control Unit. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current Shift Control Unit part number. 2. Reprogram the Shift Control Unit, if applicable.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB15-049AA
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051B
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-054
Service Bulletin/Repair Instructions
LIB PACK INTERCHANGEABILITY SERVICE INFORMATION 40kWh Lithium-ion Battery (LiB) Packs are now interchangeable between 2018-2023 vehicles. For Example: 2018-2022 LEAF 40kWh LiB packs can be used on 2023 LEAF 40kWh vehicles and 2023 LEAF 40kWh LiB packs can be used on 2018-2022 LEAF vehicles. IMPORTANT: ï The LiB modules and the Li-ion Battery Controller (LBC) are not interchangeable between LiB packs. ï If a LiB module or the LBC requires replacement, do not look up the part number in EPC using the VIN. Use the installed LiB module or LBC part number to determine the correct LiB module or LBC to order. ï Due to MY18-23 LiB pack, LiB module and LBC part numbers being restricted, please follow the existing LEAF Battery Pack pre-authorization process for Powertrain Call Center review.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013B
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051A
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-009L
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
2018-2023 LEAF P
Service Bulletin/Repair Instructions
PTC Heater *****Dealer Announcement***** Nissan is committed to a high level of customer service and satisfaction. This commitment requires Nissan to periodically place certain vehicles on temporary Quality Assurance (QA) Hold to ensure that these vehicles, as delivered to our customers, meet our exacting standards and our customersâ expectations. Effective immediately, Nissan is placing a temporary Quality Assurance Hold on all 2018-2023 Nissan LEAF vehicles due to an investigation of a potential issue with the PTC heater operation in very cold temperatures. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** 1. Please do not drive, loan, rent, sell or trade the specific vehicles in dealer inventory subject to this quality hold. 2. Nissan is currently investigating a potential concern with the PTC Heater operation. Additional information on next steps will be provided as soon as possible.
NTB15-049Z
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB15-049Y
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-105C
Service Bulletin/Repair Instructions
CLICKING/POPPING NOISE FROM FRONT AXLE AREA DURING TAKE-OFF/ACCELERATION AND/OR DECELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013A
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051
Service Bulletin/Repair Instructions
HORN INOPERATIVE IF YOU CONFIRM The horn on an APPLIED VEHICLE is inoperative. ACTION Inspect the horn pad for a pinched ground wire. If a pinched ground wire is found, replace the high and low horns.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB15-049X
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB19-105B
Service Bulletin/Repair Instructions
CLICKING/POPPING NOISE FROM FRONT AXLE AREA DURING TAKE OFF/ACCELERATION AND/OR DECELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-035
Service Bulletin/Repair Instructions
2018-2021 LEAF AND 2017-2020 ROGUE; STEERING WHEEL CHROME FINISHER REPLACEMENT SERVICE INFORMATION If the chrome finisher on the steering wheel needs to be replaced, the chrome finisher can be ordered separately from the steering wheel. SERVICE PROCEDURE 1. Remove the driver side air bag module. ï· For removal of the driver side air bag module, refer to the Electronic Service Manual (ESM), section REPAIR â RESTRAINTS â SRS AIRBAG â REMOVAL AND INSTALLATION â DRIVER AIR BAG MODULE. NOTE: ï· When removing the chrome finisher from the steering wheel, reference Figure 2 for the 6 attachment points. ï· During removal of the chrome finisher (step 2 on page 3), pull on the chrome finisher just enough to release the pawls from the steering wheel.
NTB15-049W
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-009K
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077C
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL SERVICE INFORMATION If an Applied Vehicle needs to have a front axle nut removed, for any reason, the staking of the nut into the axle keyway must first be removed. The essential tool (part number # J-52982, Figure 1) required to remove the nut staking, is called out as a âCape Chiselâ in the Electronic Service Manual (ESM), and must be used to prevent thread damage to the axle (see Figure 2 on page 2). ï· The Cape Chisel arrived at dealers in December of 2020. ï· Damaged threads, due to improper removal of the stake placed in the nut, will not be covered by warranty. For information on using the Cape Chisel, refer to the Electronic Service Manual (ESM): Section TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT > LH/RH.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-057c
Service Bulletin/Repair Instructions
2018 LEAF; MALFUNCTION AND AEB WARNING LIGHTS ON This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-086a
Service Bulletin/Repair Instructions
2018-2019 LEAF; REPLACING OR ALIGNING DISTANCE SENSOR (ICC SENSOR) BRACKET OR CHARGE PORT LID This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066b
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049v
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-042b
Service Bulletin/Repair Instructions
KICKS, LEAF, SENTRA AND VERSA; FRONT DOOR WILL NOT OPEN This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-105a
Service Bulletin/Repair Instructions
CLICKING/POPPING NOISE FROM FRONT AXLE AREA DURING TAKE OFF/ACCELERATION AND/OR DECELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066a
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. ï· For all other models/model years, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure. ï· Refer to the ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).
NTB15-049u
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-042a
Service Bulletin/Repair Instructions
2018-2020 LEAF; FRONT DOOR WILL NOT OPEN This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-017
Service Bulletin/Repair Instructions
2018-2019 LEAF; EV BATTERY WARNING LIGHT ON AND DTC B2902-42 STORED IF YOU CONFIRM The EV Battery warning light is ON AND DTC B2902-42 (PDM POWER DELIVERY MODULE) is stored. ACTION 1. Confirm the current Power Delivery Module (PDM) part number. 2. Reprogram the PDM, if applicable.
NTB15-049t
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-056a
Service Bulletin/Repair Instructions
2018-2019 LEAF; LITHIUM-ION BATTERY WILL NOT QUICK CHARGE This bulletin has been amended. See Amendment History on the last page. Discard all previous versions of this bulletin.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NTB19-055a
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2011-2019 LEAF; LITHIUM-ION BATTERY BONDING PLATES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-056
Service Bulletin/Repair Instructions
2018-2019 LEAF; LITHIUM-ION BATTERY WILL NOT QUICK CHARGE This bulletin applies only to vehicles equipped with a 40kWh lithium-ion battery. IF YOU CONFIRM The customer states their vehicle will not charge with a quick charge setting after many back-to-back quick charges Or It takes too long to charge with a quick charge setting. NOTE: - DTC U1009-96 (Quick charger comm [Quick charger communication]) may be stored. - This issue applies to vehicles equipped with a 40 kWh lithium-ion battery only. ACTION Refer to step 20 under SERVICE PROCEDURE to confirm this bulletin applies to the vehicle being worked on. - If this bulletin applies, reprogram the lithium battery controllers (LBC) for HV BATTERY 2 and HV BATTERY.
P9312 2011-19 LE
Service Bulletin/Repair Instructions
Lithium-ion Battery Bonding Plate Voluntary Service Campaign ***** Campaign Summary***** Nissan is committed to the safety, security and satisfaction of our customers and their passengers, as well as the safety of Nissan technicians. Nissan will be conducting a voluntary service campaign in North America on certain MY 2011-19 Nissan LEAF vehicles to replace the Lithium-ion Battery Bonding Plates. The plates may corrode and in areas where road salt is extensively used, could break. In rare cases during vehicle servicing in which both plates fail, the battery cover plate is removed and the vehicle is left in READY mode, a technician could be exposed to electric shock if all EV servicing safety instructions are not followed. Although no such incidents have been reported to Nissan, this voluntary service campaign is being conducted as a preventative measure out of an abundance of caution. The issue does not affect battery or vehicle performance. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History ? Open Campaigns I.D. P9312. - New vehicles in dealer inventory can be also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB19-055 to remedy any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
P9312 LEAF Autom
Service Bulletin/Repair Instructions
2011?2019 LEAF Lithium?ion Battery Bonding Plate Voluntary Service Campaign Automatic Parts Shipment
NTB19-055
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2011-2019 LEAF; LITHIUM-ION BATTERY BONDING PLATES This bulletin applies to 2018-2019 vehicles equipped with a 40kWh lithium-ion battery. INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2011-2019 LEAF vehicles to replace the Lithium-Ion battery bonding plates. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P9312 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
NTB15-049s
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
NTB15-009j
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSINGOR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB15-049r
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB18-057b
Service Bulletin/Repair Instructions
2018 LEAF; MALFUNCTION AND AEB WARNING LIGHTS ON This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-086
Service Bulletin/Repair Instructions
2018-2019 LEAF; REPLACING OR ALIGNING DISTANCE SENSOR (ICC SENSOR) BRACKET OR CHARGE PORT LID SERVICE INFORMATION If a distance sensor (ICC sensor) bracket is removed or replaced (see Figure 1 on the next page): - Take care when handling the distance sensor bracket. It can be damaged if dropped. - Do not bend the distance sensor bracket to adjust radar alignment. NOTE: If the distance sensor is difficult to align, confirm the bracket is not bent by comparing it to a known good vehicle. - Always perform an ICC Sensor Alignment (Radar Alignment Procedure) whenever the distance sensor bracket is removed or replaced. - To locate the Radar Alignment Procedure in the Electronic Service Manual (ESM), select the "Trouble Diagnosis" section and enter ICC Sensor Alignment into the Title Search field. If a charge port lid is removed or replaced: - Do not bend the charge port lid frame to adjust (Figure 2). - Do not bend any of the components attached to the charge port bracket (Figure 2). - To locate the Charge Port Lid Adjustment Specs and Procedure in the ESM, select the ?Inspection, Removal, and Installation? section and enter Charge Port Lid Assembly into the Title Search field. - Always perform an ICC Sensor Alignment (Radar Alignment Procedure) whenever any of the components called out in Figure 2 are removed or replaced. - To locate the Radar Alignment Procedure in the Electronic Service Manual (ESM), select the "Trouble Diagnosis" section and enter ICC Sensor Alignment into the Title Search field.
NTB15-077b
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB15-049q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
NTB18-057a
Service Bulletin/Repair Instructions
2018 LEAF; MALFUNCTION AND AEB WARNING LIGHTS ON This bulletin has been amended to update the color of the distance sensor mounting tab to yellow. Please discard all previous versions of this bulletin.
NTB18-057
Service Bulletin/Repair Instructions
2018 LEAF; MALFUNCTION AND AEB WARNING LIGHTS ON IF YOU CONFIRM Malfunction and Automatic Emergency Braking (AEB) warning lights are ON with DTCs: - C1B84-00 ? (DIST SEN MALFUNCTION) - C1A17-49 ? (CONTROL UNIT (INTERNAL ELECTRONIC ERROR)) ACTION 1. Install the new Distance Sensor. 2. Add a foam strip to the new Distance Sensor. 3. Perform Radar Alignment. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work youwill be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB15-049p
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.
NTB18-017b
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.
NTB18-042
Service Bulletin/Repair Instructions
2018 LEAF; FRONT DOOR WILL NOT OPEN IF YOU CONFIRM Either front door of an affected vehicle will not open with either the inside or outside door handle and The door handles, cables, and latch are in good working order and There is no damage to the door. ACTION Inspect, and adjust as necessary, the gap between the lever on the latch and the tab of the stiffener. - Go to this bulletin?s Service Procedure for Inspection. CAUTION: Do not bend the stiffener tab up or down only to adjust the gap. See this bulletin?s Service Procedure for proper adjustment.
PC622
Service Bulletin/Repair Instructions
State Specific Bumper Performance Label Dealer Inventory *****Detailed Information***** Nissan is conducting a quality action specific to dealers located in California and Hawaii only to apply a supplemental bumper performance label. Due to an issue that has since been corrected, the bumper performance language may be missing from the Monroney label. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. In the interest of customer satisfaction, Nissan requests dealers to apply the supplemental bumper performance label on the affected vehicles prior to retail sale. *****What Dealers Should Do***** 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History ? Open Campaign I.D. PC622 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to remedy vehicles affected by this quality action. 3. The service department should submit the applicable warranty claim for the action(s) performed so it can be closed on Service Comm and release the vehicle. 4. Dealers will receive five (5) extra labels, but if additional labels are needed, please send your request for the number of labels needed to CampaignAnnouncements@nissan-usa.com along with your dealer name, address and contact name and phone number. - Labels will be mailed beginning May 25, 2018 and should arrive no later than June 1, 2018
NTB15-009i
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The tables on pages 6 - 9 have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-018c
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-009h
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The tables on page 5 and 6 have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-017a
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.
NTB11-044c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-009g
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The Applied Vehicles section has been revised, and changes have been made to the table beginning on page 5. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-017
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.
NTB15-049o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.